固相球磨法制备丙烷氧化脱氢V2O5/NiO催化剂

以不同温度焙烧制备的NiO和V2O5为前驱物,采用固相球磨法制备了V2O5/NiO催化剂,考察了前驱物的焙烧温度对该催化剂丙烷氧化脱氢制丙烯反应性能的影响,并采用x射线衍射、N2物理吸附、电感耦合等离子体原子发射光谱、透射电子显微镜、H2程序升温还原和x射线光电子能谱等对催化剂进行了表征.结果表明,固相球磨法制备的V2O5/NiO催化剂表现出较好的丙烷氧化脱氢制丙烯催化性能,当以400℃焙烧的氧化物为前驱体时,V2O5/NiO催化剂表面含有较多的未完全还原氧物种Oδ-,因而表现出了较高的丙烯选择性.在475℃反应时,丙烷转化率可达20.1%,丙烯选择性达到71.2%.     

不同制备方法的Mn-Ce催化剂低温SCR性能研究

采用新型共沉淀法、浸渍法以及沉淀沉积法制备基于Mn-Ce的催化剂. 对比60～160 ℃温度区间内三种方法制备的催化剂的低温选择性催化还原NO性能. 运用X射线衍射(XRD)、比表面积(BET)、程序升温脱附(NH₃-TPD)、程序升温还原(H₂-TPR)等对催化剂的形貌与性质进行了表征. 实验结果表明, 共沉淀法制备的Mn-Ce/TiO₂有更好的低温催化还原NO活性. 影响沉淀法低温催化还原NO活性的主要因素是催化剂的表面积、活性组分的分布以及Mn与Ti之间的内在作用.     

新型铁锰复合氧化物催化低温脱除NOx

采用溶胶-凝胶法合成了一系列铁锰复合氧化物催化剂, 利用X射线衍射(XRD)对催化剂的活性相态进行研究, 并考察了铁锰摩尔比及焙烧温度对催化性能的影响. 结果表明, 该催化剂体系在低温(80-220 ℃)下选择性催化氨还原NOx反应中显示出优异的活性. 其中Fe(0.4)-MnOx(500)(即摩尔比n(Fe)/(n(Fe)+n(Mn))=0.4, 焙烧温度500 ℃)催化剂具有最佳低温催化活性, 在空速30000 h-1, 温度80 ℃的条件下, NOx转化效率达到90.6%, N2选择性达100%. Fe-MnOx复合氧化物催化剂中形成的Fe3Mn3O8晶相有利于促进NO氧化成NO2, 从而提高低温选择性催化还原的活性.     

新型铁锰复合氧化物催化低温脱除NOx

采用溶胶-凝胶法合成了一系列铁锰复合氧化物催化剂,利用X射线衍射(XRD)对催化剂的活性相态进行研究,并考察了铁锰摩尔比及焙烧温度对催化性能的影响.结果表明,该催化剂体系征低温(80-220℃)下选择性催化氨还原NOx反应中显示出优异的活性.其中Fe(0.4)-MnOx(500)(即摩尔比n(Fe)/(n(Fe)+n(Mn))=0.4,焙烧温度500℃)催化剂具有最佳低温催化活性,在空速30000 h-1,温度80℃的条件下,NOx转化效率达到90.6%,N2 选择性达100%.Fe-MnOx复合氧化物催化剂中形成的Fe3Mn3O8晶相有利于促进NO氧化成NO2,从而提高低温选择性催化还原的活性.     

制备条件对Pd催化剂上C3H6选择性还原NO性能的影响

采用浸渍法和溶胶凝胶法,制备了Pd/AI2O3和Pd/AI2O3-CeO2样品,并测定了不同温度焙烧后催化剂的物相、比表面积及对丙烯选择性还原NO的活性。对于Pd/AI2O3,随着焙烧温度的提高,其NO的最大转化率逐渐下降,对应的反应温度在290－310℃左右,而溶胶凝胶法制备的样品活性略高于浸渍法制备的样品;对于Pd/AI2O3-CeO2,经600℃焙烧后,其NO的最大转化率为22％,900℃焙烧的催化剂样品上NO的最大转化率达到40％左右,对应的反应温度也逐渐下降,说明活性随焙烧温度的提高而明显提高,溶胶凝胶法和浸渍法制备的样品结果很接近,浸渍法制备了若干不同Pd负载量的Pd/AI2O3样品,活性测定的结果表明,Pd含量在0．5％左右的催化剂样品中具有最高的活性。     

氧化态Co/γ-Al2O3催化剂的结构与反应性能研究Ⅰ. 活性及体相、表相结构表征

采用等量浸渍法, 制得500、 600、 750和950 ℃焙烧的Co/γ-Al2O3催化剂; 考察了它们对CO氧化和乙烯选择还原NO的反应性能; 用XRD和XPS方法表征了催化剂的体相与表相结构. 活性测试结果表明, 随焙烧温度升高, 样品对CO的氧化活性呈下降趋势; 对乙烯选择还原NO反应, 活性先上升, 而后又有所下降(当焙烧温度高于750 ℃时). 从硝酸钴制得的样品, 其氧化活性要高于从醋酸钴制得的样品, 但对乙烯选择还原NO, 后者的活性更好. 结构表征结果表明, 催化剂中钴物种的存在形式与原料盐类及焙烧温度密切相关. 在Co/γ-Al2O3催化剂中主要存在两种钴相, 即Co3O4和非化学计量的CoxAl(8/3-2x/3)O4尖晶石相, 前者为完全氧化活性中心, 后者是NO选择还原的活性中心. 在相同焙烧温度下, 以醋酸钴为原料时, 更容易形成CoxAl(8/3-2x/3)O4尖晶石相. 随着焙烧温度提高, 活性组分与载体的相互作用加强, Co3O4相逐步向CoxAl(8/3-2x/3)O4尖晶石相转化, 这可能是样品氧化活性下降和选择还原活性升高的主要原因. 在更高焙烧温度下, 随着CoxAl(8/3-2x/3)O4尖晶石相颗粒度的增加和晶形改变, 以及钴离子由表相向体相的迁移, 使样品比表面积下降, 表面氧空位及活性位减少, 从而导致样品对乙烯选择还原NO的活性下降.     

Sn/Al2O3催化剂结构与选择性催化还原NO性能

以不同沉淀剂和铝盐与SnCl4共沉淀制备了Sn/Al2O3催化剂.考察了催化剂在富氧条件下催化丙烯选择性还原NO的性能,借助于X射线衍射(XRD)、扫描电镜(SEM)、N2吸附-脱附、吡啶吸附红外光谱(Py-IR)和程序升温还原(TPR)等方法研究了催化剂性能与结构的关系.发现以NH3.H2O和NH4HCO3为沉淀剂、NH4Al(SO4)2为铝盐制备的Sn/Al2O3催化剂催化活性最高,NO转化率达90.9%,最佳催化活性温度为350℃.该催化剂的比表面积为254 m2/g,孔体积为0.878 cm3/g,孔径分布曲线在3~8 nm出现双峰,Sn物种主要以晶态SnO2存在,且表面Lewis酸酸量增加.     

氧化态Co/γ-Al_2O_3催化剂的结构与反应性能研Ⅰ.活性及体相、表相结构表征

采用等量浸渍法 ,制得 5 0 0、 6 0 0、 75 0和 95 0℃焙烧的 Co/ γ- Al2 O3催化剂 ;考察了它们对 CO氧化和乙烯选择还原 NO的反应性能 ;用 XRD和 XPS方法表征了催化剂的体相与表相结构 .活性测试结果表明 ,随焙烧温度升高 ,样品对 CO的氧化活性呈下降趋势 ;对乙烯选择还原 NO反应 ,活性先上升 ,而后又有所下降 (当焙烧温度高于 75 0℃时 ) .从硝酸钴制得的样品 ,其氧化活性要高于从醋酸钴制得的样品 ,但对乙烯选择还原 NO,后者的活性更好 .结构表征结果表明 ,催化剂中钴物种的存在形式与原料盐类及焙烧温度密切相关 .在 Co/ γ- Al2 O3催化剂中主要存在两种钴相 ,即 Co3O4和非化学计量的 Cox Al( 8/ 3- 2 x/ 3) O4尖晶石相 ,前者为完全氧化活性中心 ,后者是 NO选择还原的活性中心 .在相同焙烧温度下 ,以醋酸钴为原料时 ,更容易形成 Cox Al( 8/ 3- 2 x/ 3) O4尖晶石相 .随着焙烧温度提高 ,活性组分与载体的相互作用加强 ,Co3O4相逐步向 Cox Al( 8/ 3- 2 x / 3) O4尖晶石相转化 ,这可能是样品氧化活性下降和选择还原活性升高的主要原因 .在更高焙烧温度下 ,随着 Cox Al( 8/ 3- 2 x / 3) O4尖晶石相颗粒度的增加和晶形改变 ,以及钴离子由表相向体相的迁移 ,使样品比表面积下降 ,表面氧空位及活性位减少 ,     

焙烧温度对MnO_x-CeO_2-WO_3-ZrO_2催化剂上NH_3选择性还原NO的影响（英文）

采用共沉淀法制备了MnOx-CeO2-WO3-ZrO2催化剂,考察了催化剂焙烧温度对O2和H2O存在下NH3选择性催化还原(NH3-SCR)NO的影响,并利用低温N2吸附、X射线衍射(XRD)、透射电镜(TEM)、X射线光电子能谱(XPS)、NH3程序升温脱附(NH3-TPD)和CO脉冲反应对催化剂进行了表征.结果表明在NH3-SCR反应中,催化剂的低温活性随焙烧温度的提高而降低,这是由于催化剂表面化学吸附氧和酸性位减少引起的;催化剂的高温活性随焙烧温度的提高先增加后减小,这与催化剂表面最易释放氧数量的变化趋势相反.700°C焙烧的催化剂具有良好的低温活性和最宽的反应温度窗口,在空速为90000 h-1的条件下,该催化剂的起燃温度(50%NO转化率)为189°C,且反应温度在218-431°C范围内,NO转化率可达到80%-100%.     

制备方法对Co_3O_4-CeO_2催化剂催化性能的影响研究

用水热法、共沉淀法、柠檬酸络合物法和多元醇法分别合成了铈钴摩尔比1∶1的Co3O4-CeO2催化剂,并用XRD、TPR、TPD、FT-IR、BET等对催化剂的晶相结构、还原性能、吸附性能及比表面积等进行了表征.结果表明,制备方法对Co3O4-CeO2催化剂的催化性能具有较大的影响,其中多元醇法制备的催化剂能促进Co3O4和CeO2的相互作用,该催化剂还原温度较低、CO脱附面积较大,在140℃温度下,CO的转化率达到90%以上.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

A carbanion induced synthesis of highly congested pyrazole and imidazole containing heterocycles

An efficient approach to the synthesis of highly congested di, penta and hexacyclic pyrazoles as well as imidazole fragment containing novel heterocyclic molecule has been developed through a carbanion induced transformation of suitably functionalized 2H-pyran-2-ones, benzo[h]chromene and thiochromeno[4,3-b]pyrans. Due to the presence of fluorescence, we report their prime application metal sensor as off/on switching in ferric ions.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

正丁胺对激光染料荧光谱影响的研究

用正丁胺作为碳源,采用射频辉光放电制备碳膜,选用激光染料R6G和聚乙二醇混合液作为蒸气源,采用单源热蒸发,在蒸发室与染料同时沉积得到混合膜,用拉曼光谱和红外光谱分析了碳膜的结构和键合方式,分析表明:碳膜中存在胺基团和氢原子.混合膜的荧光谱测量结果表明,认为正丁胺对染料荧光谱的影响是因为胺基和氢原子的存在.     

Selective synthesis of 4,5-dihydroimidazo- and imidazo[1,5-a]quinoxalines via modified Pictet–Spengler reaction

An efficient tandem approach for the selective synthesis of 4,5-dihydroimidazo[1,5-a]quinoxalines 6a–g and imidazo[1,5-a]quinoxalines 7a–h by the reaction of 2-imidazolyl anilines 4a–c with aryl aldehydes 5a–k under mild reaction conditions is described. Introduction of electron releasing alkyl groups in substrates 4a–b was found to be instrumental for the success of the reaction.     

Understanding the Diels-Alder reactivity of 1,2-azaborine analogues

The Diels-Alder reactivity of 1,2-heteroborines (H₄C₄B(H)X, X?=?NH, PH, AsH; O, S, Se) has been computationally explored by means of Density Functional Theory (DFT) calculations. The influence of the HB?=?X fragment on the reactivity of the system has been quantitatively analyzed in detail by means of the so-called Activation Strain Model (ASM) of reactivity. It is found that the interaction between these species and the dienophile is significantly stronger than that computed for their all-carbon isoelectronic counterpart, benzene. In addition, the strain energy plays a key role in the observed reactivity trends. The role of the aromaticity strength of these heteroarenes on the reactivity is also assessed.