Al-Ni-Y三元共晶合金高压凝固组织

利用光学显微镜,扫描电镜,X射线衍射仪对不同压力(2,4,6 GPa)下凝固的Al-1Ni-3Y(%,原子分数)共晶合金组织形貌和相组成进行研究,并且与常压条件下合金凝固组织进行对比。实验结果表明,与常压凝固相比,在超高压力条件下凝固的合金的显微组织形貌发生了很大的改变,但是合金的相组成没有发生变化。常压凝固的合金具有共晶团组织,而高压下凝固的合金具有枝晶状亚共晶组织。高压凝固合金显微组织中出现了大量的初生α-Al相,这表明高压条件下凝固的合金共晶点发生偏移,使得常压共晶成分的合金在高压下变成亚共晶成分合金。同时,共晶组织的形貌发生了很大变化,常压下凝固的合金的组织为Al3Y相与α-Al相形成的菊花状的二元共晶和Al23Ni6Y4相与α-Al相形成的层片状的二元共晶,而高压下这两种共晶组织逐渐转化为离异共晶组织。随着压力的增大,共晶第二相的体积分数减小,α-Al的晶格常数增加。     

定向凝固Al-Ni-Y三元共晶合金的相组成与凝固特征

在5 K.mm-1温度梯度下,选用1,5,10 mm.min-1三种拉速率对成分为96.0%Al,1.0%Ni,3.0%Y的三元共晶合金进行定向凝固实验,研究下拉速率对合金组织演化的影响规律。通过X射线衍射和光学显微镜分析表明合金由α-Al相、Al3Y相、Al23Ni6Y4相三相组成。当下拉速率为1 mm.min-1时,合金组织呈现三相共晶结构,纵截面有定向凝固趋势;下拉速率为5和10 mm.min-1时,合金组织演变成两种二相共晶:一种是Al3Y相与α-Al相形成菊花状的不规则二相共晶组织,另一种是Al23Ni6Y4相与α-Al相形成层片状的规则二相共晶组织,纵截面上均有明显的定向凝固特征。     

微量元素La对Al—Si合金凝固过程的影响

本文用差热分析法系统地研究了La掺杂对Al-Si共晶合金、亚共晶、超共晶的动态凝固过程的影响。结果表明,La促使α(Al)成核,使体系中初晶α(Al)的析出温度比AJ-Si二元合金中Al初晶的实际析出温度明显提高;La对初晶Si的成核和长大起抑制作用,使超共晶中初晶Si相析出温度较二元合金中的Si初晶的实际析出温度明显降低。     

微量元素Sr对Al—Si合金凝固过程的影响

用差热分析法系统地研究了Sr对Al-Si共晶、亚共晶及超共晶合金的动态凝固过程的影响。结果表明,Sr既可促进α-Al成核,使其初晶析出温度比二元合金中α-Al相析出温度明显提高,又能抑制初晶Si成核,使超共晶中初晶Si相析出温度较二元合金中Si的初晶的实际析出温度明显降低,还能促使共晶合金成核,使加Sr后的共晶析出温度明显提高。     

稀土对镁-铝合金抗热裂性能的影响及其机制

研究了稀土（0.1%～1.2%,质量分数）对Mg-Al合金抗热裂性能的影响及其机制.结果表明： 往Mg-Al合金中添加稀土后,合金的抗热裂性能显著下降,其原因可归为： 稀土引起了Mg-Al合金晶粒粗化,使得热裂纹萌生所需的断裂应变降低;稀土减少了Mg-Al合金中的共晶组织,缩短了枝晶通道保持开通的时间,不利于合金进行补缩;而且稀土还提高了共晶反应的温度,使得凝固后期枝晶间液膜的强度有所下降;当α-Mg枝晶连成骨架时,分布在枝晶间的Al11RE3相容易堵塞枝晶通道,增加了合金补缩的难度;Al11RE3相与α-Mg基体的凝固收缩率不同,容易产生凝固收缩应力,促进热裂纹的萌生.     

阶梯模冷却Mg_(68)Zn_(29)Y_3合金的组织及准晶相的形成

采用五层阶梯形模具冷却方法在Mg68Zn29Y3合金中制备了二十面体准晶相(I相)。通过扫描电镜、能谱分析仪和透射电子显微分析技术,观察了合金凝固组织和准晶相的形貌,并确定了准晶相成分及结构。结果表明:Mg68Zn29Y3三元合金在普通凝固-阶梯模冷却过程中,冷却速度对准晶相形貌、数量、大小和分布存在较为显著的影响;随着冷速的降低,准晶相的生长方式由细小弥散演变为粗大碎化,准晶晶粒尺寸由20μm逐渐长大至100μm以上;准晶相通过包晶反应形核、长大;合金凝固组织为MgZn+α-Mg+Zn60Mg30Y10。     

压力、温度和晶粒尺寸对Fe-N合金的合成及结构的影响

在 1× 1 0 - 3 Pa～ 4 GPa的压力和 5 80～ 930 K温度范围内 ,利用高压技术并结合机械球磨 ,研究了压力、温度和晶粒尺寸对α-Fe与非晶 BN的固态反应的影响 .发现高压和晶粒细化可以极大地促进α-Fe和非晶 BN的固态反应过程 ,α-Fe与非晶 BN发生固态反应的临界晶粒尺寸约 8nm.压力和温度对反应产物及其晶体结构有明显影响 .2 GPa和 80 0 K时 ,反应产物为具有正交结构的 Fe-N新相 ;在 3～ 4 GPa和 690～80 0 K时 ,可形成单一ε-Fex N合金相 ;而在 4 GPa和 930 K以上 ,反应产物由 Fe-N合金相转变为 Fe3B相     

镧、铈对铝铜合金凝固过程及凝固组织的影响

本文用热分析对比法和金相法研究了微量镧、铈对Al-5wt％Cu合金的凝固过程和凝固组织的影响规律。发现微量镧、铈能改变该合金的凝固参数,增大其过冷度和明显细化组织,微量镧、铈改变了Al-5wt％Cu合金的凝固过程,使其在α相析出之后共晶析出之前有一中间相析出。加微量铈可形成Al_8Cu_4Ce。理论分析认为,Le_2O_3、Ce_2O_3、La(OH)_3和Ce(OH),可做为α相的异质核心。     

电脉冲作用下共晶铝硅合金凝固组织的变化

本文研究了连续电脉冲处理对共晶铝硅合金凝固组织的影响.结果显示,电脉冲处理后Al-12.5%Si共晶合金的凝固组织中出现了本应在过共晶成分的铝硅合金中才会出现的初生硅.X-射线能谱分析表明,电脉冲处理后α-Al枝晶中固溶Si含量降低.     

钇基重稀土合金变质团球γ+(Fe,Mn)3C共晶体增强奥氏体钢基自生复合材料

采用Y基重稀土合金变质处理钢液,通过影响钢液中C, Mn 等合金元素的偏析和相的生成,从而控制钢液凝固组织,在铸态下获得团球γ+(Fe, Mn)3C共晶体增强奥氏体钢基自生复合材料(AMGE). Y基重稀土合金增大C, Mn 元素的偏析,使凝固后期初生奥氏体枝晶间小熔池中的成分达到共晶反应区,在非平衡凝固条件下生成γ+(Fe, Mn)3C共晶体.干摩擦磨损试验表明,在中、低载工况下AMGE的磨损量比基体合金奥氏体中锰钢低1～3倍,并且AMGE发生严重磨损时的载荷高于基体合金.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.     

Mechanism of action of base-catalyzed oxygenation of phenol derivatives

Cyclopropyl derivative of 2,6-di-tert-butylphenol is synthesized as a probe to investigate the mechanism of base-catalyzed autooxidation of phenol derivatives. Our study indicates that one electron reduction of molecular oxygen from phenolate gives phenoxyl radical 3, a key intermediate of autooxidation. The coupling of phenoxyl radical and superoxide radical gives peroxylate anion 4 and produces the final epoxy alcohol adduct 6.     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

化学计量中不确定度评定研究进展

测量不确定度是表征合理地赋予被测量之值的分散性的参数。本文针对化学计量不确定度评定基础模型仅适用于线性模型、概率分布为正态分布或缩放位移t分布等局限,介绍了近年来不确定度评定的研究热点:蒙特卡罗方法(Monte Carlo Method,MCM),不确定度评定的来源、评定概念、评估方法及其发展过程,扩大了测量不确定度评定与表示的适用范围。     

微量钙的测定方法研究进展

介绍了1995-2006年期间测定微量和痕量钙的方法,如电感耦合等离子体-原子发射光谱法、原子吸收光谱法以及离子色谱法等的工作原理和特点,并说明了其测定微量钙的应用领域。并对微量钙的测定技术进行了展望(引用文献55篇)。