三维有序大孔锂离子筛的制备及其交换性能研究

由110 nm聚苯乙烯(PS)微球组装晶体胶体模板,并用此模板合成三维有序大孔(3-dimensionally ordered macroporous,3DOM)锂离子筛前驱体Li4Ti5O12,用1.0 mol.L-1的盐酸改型制得锂离子筛H4Ti5O12(LiTi-H)。用XRD、SEM、饱和交换容量、pH滴定曲线等表征了材料的形貌、结构和离子交换性能。同时测定了25℃时LiTi-H在0.05 mol.L-1Li+体系吸附锂的动力学数据,并采用吸附动力学Bangham方程和Elovich方程关联离子筛LiTi-H对Li+的离子交换动力学数据。结果表明:PS胶体晶体模板和3DOMLi4Ti5O12锂离子筛前驱体均排列规则有序,大孔直径约90 nm,Li4Ti5O12为尖晶石结构;3DOM Li4Ti5O12酸稳定性好,锂离子筛LiTi-H对Li+具有较高的选择性,对Li+的饱和交换容量达56.70 mg(Li+).g-1;动力学模型用Elovich模型关联较好,离子筛对Li+的离子交换动力学方程是Q=-26.510 4+11.977 4lnt(25℃)。     

Li4Ti5Ol2的合成及对Li+的离子交换动力学

用溶胶-凝胶法合成出Li4Ti5Ol2, 对其进行了酸改性, 制得锂离子筛IE-H. 测定了IE-H对Li+、Na+的饱和交换容量和pH滴定曲线等离子交换性能, 并对其进行了X射线衍射分析, 同时采用中断接触法判断该离子交换反应的控制机理, 用缩核模型描述离子筛IE-H交换Li+的动力学. 结果表明, 合成出的Li4Ti5Ol2和锂离子筛IE-H均为尖晶石结构; 用不同浓度HNO3溶液处理Li4Ti5Ol2时, Li+的抽出率为19.6%-81.5%, Ti4+的抽出率在4.2%以下; 锂离子筛IE-H 对Li+的饱和交换容量较高, 达到5.95 mmol·g-1, 离子筛IE-H交换Li+的控制步骤是颗粒扩散控制(PDC), 得到了25 ℃, Li+浓度为20.0 mmol·L-1和5.0 mmol·L-1时锂离子筛交换Li+的动力学方程和颗粒扩散系数.     

工艺参数对o-LiMnO2相纯度及Li1.6Mn1.6O4合成的影响及作用（英文）

以MnSO4,KMnO4及LiOH为原料,经水热处理后得到LiMnO2,再由固相焙烧得到尖晶石相Li1.6Mn1.6O4,酸洗处理后得到锂离子筛。研究了水热温度,氧气和MnO4-/Mn2+的物质的量之比(nMnO4∶nMn^2+)对所得LiMnO2的组成及相应前驱体Li1.6Mn1.6O4酸处理中Mn溶损率的影响。开路电势测量及化学分析表明,氧气会参与反应。若按照理论氧化剂用量nMonO4∶nMn^2+=1∶4进行水热反应会导致杂质Li2MnO3和LiMn2O4的生成。若控制水热温度为160℃,nMnO4∶nMn^2+=1∶6时可得到纯相正交LiMnO2(o-LiMnO2)。所得离子筛在高镁锂比盐湖卤水中Li+吸附容量可达42.87 mg·g^-1,且对Li+具有优异的选择吸附性并遵循化学吸附过程。经过5个循环后吸附容量保持在37.21 mg·g^-1,锰溶损率降至0.34%。     

球形PVC-MnO2离子筛的制备及锂吸附性能

本实验室前期所制备的Li4Mn5O12超细粉末在卤水体系中对Li+具有较大的吸附容量和良好的选择性。但由于超细粉体的流动性和渗透性差,无法直接应用于固定床,需对粉末吸附材料进行成型造粒,以便于实际应用。本论文采用聚氯乙烯为粘结剂,制备出粒径约为2.0~3.5 mm的球形PVC-Li4Mn5O12,经盐酸处理后得到球形PVC-MnO2离子筛。并通过扫描电镜(SEM)、X射线衍射仪(XRD)、静态和动态连续锂吸附实验研究了球形离子筛形貌和锂离子吸附性能。结果表明,球形离子筛对Li+的吸附容量高达5.28 mmol.g-1,在混合溶液中对Li+具有良好的选择性,这对于在盐湖卤水或海水提锂具有重要的实用意义。     

高效锂离子筛吸附剂MnO2·0.5H2O的软化学合成及吸附性能研究

以MnCl2·4H2O,LiOH·H2O等试剂为初始原料,采用溶胶-凝胶、水热处理、固化等软化学合成步骤制备了锂离子筛前驱体Li1.6Mn1.6O4,并经稀盐酸抽锂后得到了高选择性锂离子筛吸附剂MnO2·0.5H2O.着重对合成过程中锂锰比,氧化剂用量等因素影响进行了探讨,并对所制备吸附剂的吸附性能进行了研究.结果表明,经软化学合成步骤制备的锂离子筛对Li 有良好的吸附量和选择性,在未来从海水、卤水等液态锂资源富集或提取锂的应用中具有很大的潜力.     

富锂锂锰氧化物的制备及其在溶液中的抽Li+/吸Li+性能

采用柠檬酸配合法合成了系列尖晶石富锂锂锰氧化物Li2O.nMnO2(n=1.75,2.0,2.25,2.5,3.0)。通过X射线衍射(XRD)和酸浸实验发现,350℃合成的Li2O.2.25MnO2具有纯相尖晶石锂锰氧化物结构,且在弱酸性介质中具有较高的锂溶出率和较低的锰溶损率。Li2O.2.25MnO2在酸浸之后转型为锂离子筛。XRD和扫描电子显微镜(SEM)分析发现锂离子筛能够保持尖晶石锂锰氧化物的结构和形貌。吸附实验表明,该锂离子筛在碱性含锂溶液中对Li+具有吸附性能,且吸附容量随着溶液温度和pH值的升高而增大,最高能达到40.14 mg.g-1。通过傅立叶红外光谱(FTIR)研究了锂离子筛的吸附机理,并用Langmuir模型描述了其在LiCl+LiOH溶液中的吸附行为。     

不同晶型和形貌MnO2纳米材料的可控制备

以KMnO4为锰源, 采用水热技术在180 ℃条件下于不同种类酸溶液中可控制备了α-, β-, δ-MnO2, 系统研究了 K＋, H＋及阴离子对制备产物MnO2晶型和形貌的影响. 研究结果表明, K＋与H＋在反应体系中对于制备产物晶相的生成形成竞争性影响, 其量的大小对制备产物晶型具有控制作用, 高浓度K＋离子有助于生成α-MnO2, 而高浓度的H＋有利于生成β-MnO2; 阴离子的种类和浓度对制备产物MnO2的晶型和形貌无显著影响. 在对制备产物进行XRD, SEM和元素分析的基础上, 提出了不同晶型和形貌MnO2的可能形成机理.     

正极材料Li_(0.99)Nb_(0.01)Fe_(1-x)Mg_xPO_4/C的制备及电化学性能的研究

采用两步固相反应合成了锂、铁双位掺杂的锂离子电池正极材料Li0.99Nb0.01Fe1-xMgxPO4/C(x=0,0.01,0.02,0.03,0.04)。通过X射线衍射(XRD)、扫描电镜(SEM)以及恒电流充放电测试,研究了复合材料的晶体结构、形貌以及电化学性能。实验结果表明,制备的Li0.99Nb0.01Fe1-xMgxPO4/C(x=0,0.01,0.02,0.03,0.04)为纯相,掺杂适量的Nb5+、Mg2+离子可减小材料的晶粒尺寸,当Nb离子掺杂量为1mol%、Mg离子掺杂量为3mol%时,Li0.99Nb0.01Fe0.97Mg0.03PO4/C的电化学性能最佳。室温下,0.2C、1C、2C、4C(1C=170mA·g-1)倍率充放电其首次放电比容量分别为153.7、149.7、144.6、126.4mAh·g-1,即使在8C倍率下放电其放电比容量也有92.2mAh·g-1,并表现出良好的循环性能。     

正庚烷造孔对球形锰钛复合锂离子筛吸附性能的影响

采用低温悬浮聚合造粒法,以苯乙烯为基体,以掺杂10%Li2Ti O3的Li1.6Mn1.6O4为原料,以正庚烷为造孔剂制备球形锂离子筛前驱体,经0.5 mol/L的HCl解析后得到球形锂离子筛。用扫描电子显微镜、X射线衍射仪、原子吸收分光光度计对样品的形貌和吸附性能等进行表征,实验结果表明,加入苯乙烯体积的5%正庚烷后的锂离子筛呈球形,锂离子筛中的孔隙率明显增加,比表面积达到1.768 m2/g,锂离子筛锂吸附量达到最大值9 mg/g,相比不添加正庚烷的对照组锂吸附量增加28.8%。吸附过程符合二级吸附动力学模型,属于化学吸附。球形锂离子筛的循环性能较好,添加5%正庚烷锂离子筛循环吸附10次后,Mn平均单次溶损率为0.13%,Ti平均单次溶损率为0.028%。     

锂离子交换剂制备及交换反应动力学

通过XRD分析、Li＋抽出率βLi及Mn2＋溶出率γMn的计算，考察了不同焙烧温度及抽锂剂对前驱体锂锰氧化物LiMn2O4结构及稳定性的影响.结果表明, 750 ℃下焙烧2 h，并使用过硫酸铵(NH4)2S2O8作抽锂剂，制备的Li＋交换剂MnO2(Li)对Li＋的交换容量αLi较大.另外，通过Li＋在固液两相间分配系数的测定及交换反应动力学实验，对离子交换反应机理进行了研究，并建立了有限浴条件下MnO2(Li)离子交换反应动力学模型.结果表明,该离子交换过程近似符合颗粒扩散控制；交换反应主要发生在交换剂颗粒外层；提出的动力学模型与实验结果符合较好.     

高效锂离子筛吸附剂MnO2•0.5H2O的软化学合成及吸附性能研究

以MnCl₂•4H₂O, LiOH•H₂O等试剂为初始原料, 采用溶胶-凝胶、水热处理、固化等软化学合成步骤制备了锂离子筛前驱体Li_1.6Mn_1.6O₄, 并经稀盐酸抽锂后得到了高选择性锂离子筛吸附剂MnO₂•0.5H₂O. 着重对合成过程中锂锰比, 氧化剂用量等因素影响进行了探讨, 并对所制备吸附剂的吸附性能进行了研究. 结果表明, 经软化学合成步骤制备的锂离子筛对Li^＋有良好的吸附量和选择性, 在未来从海水、卤水等液态锂资源富集或提取锂的应用中具有很大的潜力.     

HTO/Cellulose Aerogel for Rapid and Highly Selective Li+ Recovery from Seawater

To achieve rapid and highly efficient recovery of Li⁺ from seawater, a series of H₂TiO₃/cellulose aerogels (HTO/CA) with a porous network were prepared by a simple and effective method. The as-prepared HTO/CA were characterized and their Li⁺ adsorption performance was evaluated. The obtained results revealed that the maximum capacity of HTO/CA to adsorb Li⁺ was 28.58 ± 0.71 mg g⁻¹. The dynamic k₂ value indicated that the Li⁺ adsorption rate of HTO/CA was nearly five times that of HTO powder. Furthermore, the aerogel retained extremely high Li⁺ selectivity compared with Mg²⁺, Ca²⁺, K⁺, and Na⁺. After regeneration for five cycles, the HTO/CA retained a Li⁺ adsorption capacity of 22.95 mg g⁻¹. Moreover, the HTO/CA showed an excellent adsorption efficiency of 69.93% ± 0.04% and high selectivity to Li⁺ in actual seawater. These findings confirm its potential as an adsorbent for recovering Li⁺ from seawater.     

WQD-1沸石离子交换性能的研究

测定了W_QD-1沸石在一价碱金属离子混合溶液中的分配系数、饱和交换量和在25℃时，NH⁺₄/K⁺、NH⁺₄/Na⁺交换等温线。得出该沸石一价离子选择性序列为：Cs⁺>Rb⁺>K⁺>Na⁺>Li⁺, Na⁺/K⁺交换自由焓变ΔG(T,P)=-6.745 KJ/mol。     

Lithium extraction/insertion process on cubic Li-Mn-O precursors with different Li/Mn ratio and morphology

The cubic phase LiMn₂O₄ precursors are prepared by high-temperature calcinations (1003 K) of LiOH⋅H₂O and MnO₂ mixture with Li/Mn molar ratio = 0.55. The Li₄Mn₅O₁₂ precursors are synthesized via low-temperature solid-phase reaction (673 K) of LiNO₃ and MnO₂ mixture with Li/Mn molar ratio = 1.0. The ion-sieves counterparts (named SMO-H and SMO-L, respectively) are obtained by the acid treatment of Li-Mn-O precursors. The structure, chemical stability, morphology, ion-exchange property and mechanism of Li-Mn-O precursors and MnO₂ ion-sieve were systematically examined via X-ray diffraction (XRD), high-resolution transmission electron microscopy (HRTEM), selected-area electron diffraction (SAED), Infrared Spectroscopy (IR), X-ray photoelectron spectroscopy (XPS) and lithium ion selective adsorption measurements. The result shows the more compact Mn-O lattice makes the Li₄Mn₅O₁₂ spinel more stable after the Li⁺ is extracted. The results of IR and XPS show adsorption process of SMO-H exists ion-exchange between the Li⁺ and protons, and redox reaction, but only exists ion-exchange between the Li⁺ and protons in SMO-L. Agglomeration is well-improved by low calcination temperature and the morphology of the Li₄Mn₅O₁₂ precursor and final MnO₂ ion-sieve are effectively controlled within low-dimensional structure. The maximum pH titration capacity of SMO-L for Li⁺ is 6.76 mmol⋅g⁻¹, but only 3.47 mmol⋅g⁻¹ for SMO-H. The ion-sieve obtained from Li₄Mn₅O₁₂ precursor is promising in the lithium extraction from brine or seawater.     

(NH4)2V7O16 Microbricks as a Novel Anode for Aqueous Lithium-Ion Battery with Good Cyclability

Searching for novel anode materials to address the issues of poor cycle stability in the aqueous lithium-ion battery system is highly desirable. In this work, ammonium vanadium bronze (NH₄)₂V₇O₁₆ with brick-like morphology has been investigated as an anode material for aqueous lithium-ion batteries and Li⁺/Na⁺ hybrid ion batteries. The two novel full cell systems (NH₄)₂V₇O₁₆||Li₂SO₄||LiMn₂O₄ and (NH₄)₂V₇O₁₆||Na₂SO₄||LiMn₂O₄ both demonstrate good rate capability and excellent cycling performance. A capacity retention of 78.61 % after 500 cycles at 300 mA g⁻¹ was demonstrated in the (NH₄)₂V₇O₁₆||Li₂SO₄||LiMn₂O₄ system, whereas no capacity attenuation is observed in the (NH₄)₂V₇O₁₆||Na₂SO₄||LiMn₂O₄ system. The reaction mechanisms of the (NH₄)₂V₇O₁₆ electrode and impedance variation of the two full cells were also researched. The excellent cycling stability suggests that layered (NH₄)₂V₇O₁₆ can be a promising anode material for aqueous rechargeable lithium-ion batteries.     

Alkali metal cation doping of metal-organic framework for enhancing carbon dioxide adsorption capacity

Metal-organic frameworks (MOFs) have attracted much attention as adsorbents for the separation of CO₂ from flue gas or natural gas. Here, a typical metal-organic framework HKUST-1(also named Cu-BTC or MOF-199) was chemically reduced by doping it with alkali metals (Li, Na and K) and they were further used to investigate their CO₂ adsorption capacities. The structural information, surface chemistry and thermal behavior of the prepared adsorbent samples were characterized by X-ray powder diffraction (XRD), thermo-gravimetric analysis (TGA) and nitrogen adsorption-desorption isotherm analysis. The results showed that the CO₂ storage capacity of HKUST-1 doped with moderate quantities of Li⁺, Na⁺ and K⁺, individually, was greater than that of unmodified HKUST-1. The highest CO₂ adsorption uptake of 8.64 mmol/g was obtained with 1K-HKUST-1, and it was ca. 11% increase in adsorption capacity at 298 K and 18 bar as compared with HKUST-1. Moreover, adsorption tests showed that HKUST-1 and 1K-HKUST-1 displayed much higher adsorption capacities of CO₂ than those of N₂. Finally, the adsorption/desorption cycle experiment revealed that the adsorption performance of 1K-HKUST-1 was fairly stable, without obvious deterioration in the adsorption capacity of CO₂ after 10 cycles.     

Synthesis of LiAlTiO4 and its selectivity to Li+ exchange

The ion-exchanger LiAlTiO₄ of spinel type was prepared by the common precipitation/hydrothermal crystallization method, and was acid-modified. Its ion-exchange properties for alkali ions such as saturation capacity of exchange, distribution coefficient and pH titration curve were determined. LiAlTiO₄ was characterized by the X-ray diffraction method. The acid treatment of LiAlTiO₄ caused Li⁺ extraction ratio to change from 28% to 72%, while the dissolution of Al is less than 6.8%. This inorganic ion-exchanger (LiAlTiO₄-700) has a higher saturation capacity of exchange for Li than for other alkali ions, the saturation capacity of exchange for Li⁺ reaches 4.29 mmol/g (30.03 mg/g); LiAlTiO₄-700(H) has a higher selectivity of ion exchange for Li⁺ than for other alkali ions. These results show LiAlTiO₄-700(H) has better memory and selectivity of ion exchange, and higher capacity of ion exchange for Li⁺. It is a kind of prospective ionic sieve for Li⁺. __________ Translated from Chinese Journal of Applied Chemistry, 2005, 22 (7) (in Chinese)     

Novel Fe3O4/hydroxyapatite/β‐cyclodextrin nanocomposite adsorbent: Synthesis and application in heavy metal removal from aqueous solution

The increased global concern on environmental protection has made researchers focus their attention on new and more efficient methods of pollutant removal. In this research, novel nanocomposite adsorbents,i.e., magnetic hydroxyapatite (Fe₃O₄@HA) and magnetic hydroxyapatite β‐cyclodextrin (Fe₃O₄@HA‐CD) were synthesized and used for heavy metal removal. The adsorbents were characterized by FTIR, XRD, TGA, VSM, and SEM. In order to investigate the effect of β‐cyclodextrin (β‐CD) removal efficiency, adsorption results of nine metal ions were compared for both adsorbents. β‐CD showed the most increasing effect for Cd²⁺ and Cu²⁺ removal, so these two ions were selected for further studies. The effect of diverse parameters including pH, contact time, initial metal ion concentration and adsorbent dosage on the adsorption process was discussed. The optimum pH was 6 and adsorption equilibrium was achieved after 1 hr. Adsorption kinetic data were well fitted by pseudo‐second‐order model proposing that metal ions were adsorbed via chemical reaction. Adsorption isotherm was best described by the Langmuir model, and maximum adsorption capacity for Cd²⁺ and Cu²⁺ was 100.00 and 66.66 (mg/g), respectively. Desorption experiment was also done, and the most efficient eluent used for desorption of metal ions was EDTA (0.001 M) with 91% and 88% of Cd²⁺ and Cu²⁺ release, respectively. Recyclability studies also showed a 19% decrease in the adsorption capacity of the adsorbent after five cycles of regeneration. Therefore, the synthesized adsorbents were recognized as potential candidates for heavy metal adsorption applications.     

Thermodynamic properties of aqueous mixtures of LiCl and Li2SO4 at different temperatures

Emf measurements were made on the cell without liquid junction: Li?ISE LiCl(m₁), Li₂SO₄(m₂) Ag/AgCl. The performances of the electrode pairs constructed in our laboratory were tested and exhibited near-Nernstian behavior. The mean activity coefficients of LiCl for the system Li⁺?Cl^??SO ₄ ^2? ?H₂O have been investigated by the emf values at temperatures of 0, 15, 35°C and constant total ionic strengths of 0.05, 0.1, 0.5, 1.0, 2.0, 3.0 and 5.0 mol·kg^?1. The activity coefficients decrease with increasing temperature and the ionic strength fraction of Li₂SO₄ in the mixtures. The thermodynamic properties are interpreted by use of Harned's empirical equations and Pitzer's ion interaction approach including the contribution of higher order electrostatic terms. The experimental results obey Harned's rule and are described by using Pitzer equations satisfactorily. The activity coefficients of Li₂SO₄, the osmotic coefficients and the excess free energies of mixing for the system in the experimental temperature range were reported.