微乳液催化苯乙烯聚合反应

微乳液催化苯乙烯聚合反应１）郝京诚汪汉卿２）（中国科学院兰州化学物理研究所兰州７３００００）石元昌李干佐（山东大学胶体与界面化学研究所济南２５０１００）关键词微乳液催化苯乙烯聚合微乳液［１］是油、水、表面活性剂和助表面活性剂在适当比例下自发形成的热力...     

O／W微乳液催化苯乙烯聚合动力学研究

Ｏ／Ｗ微乳液催化苯乙烯聚合动力学研究１）郝京诚孙海英汪汉卿２）（中国科学院兰州化学物理研究所兰州７３００００）尤进茂（曲阜师范大学化学系曲阜２７３１６５）关键词微乳液催化苯乙烯聚合动力学分类号Ｏ６４３．１３微乳液作为聚合反应介质，催化单体聚合反应研究...     

微乳液法制备Pt/ZrO2催化剂及其催化加氢活性研究

采用十六烷基三甲基溴化铵（CTAB）/正丁醇/环己烷/H2PtCl6微乳液体系,以N2H4.H2O为还原剂,ZrO2为载体,制备Pt/ZrO2催化剂。以对氯硝基苯（p-CNB）选择加氢反应为探针,考察微乳液组成及载体焙烧温度对Pt/ZrO2催化剂催化活性的影响。由TEM、XRD对载体和催化剂进行表征。结果表明,采用微乳...     

Ｌa1—xSrxMn0.7Zn0.3O3＋λ钙钛矿的制备及稀燃条件下氮氧化物的催化还原性能

利用微乳液法和共沉淀法制备了Ｌa1-xSrxMn0.7Zn0.3O3 λ纳米钙钛矿材料，研究了在稀燃条件下对一氧化氮（NO）还原催化活性。结果表明，在10％O2的富氧气氛下，利用微乳液法得到的Ｌa1-xSrxMn0.7Zn0.3O3 λ催化剂的NO转化率在430℃达到80％左右，与之相比，共沉淀法得到的试样只有48％。XRD分析发现，Sr^2 进入钙钛矿晶格，部分取代La^3 ，使催化剂活性提高，而过量的Sr^2 则导致Mn 由三价变为四价，形成SrMnO3，催化活性降低。表面形貌照片表明微乳液法制备的纳米粒子粒径较小，尺寸分布均匀。     

微乳液凝胶固定化脂肪酶催化α-单硬脂酸甘油酯水解反应活性

微乳液凝胶固定化脂肪酶催化α-单硬脂酸甘油酯水解反应活性;微乳液凝胶;固定化脂肪酶;催化活性;水解反应;α-单硬脂酸甘油酯     

SDBS/n-C8H18/n-C4OH/盐水体系中相微乳液双连续结构

微乳液是指由水（盐水）、油（烃）、一种或几种表面活性剂组成的热力学稳定体系,这类体系具有低粘度、各向导性、透明或半透明的性质[1],微乳液在许多工业实际问题中,例如润滑、以洗涤、催化等方面得到了应用[2],近年来,微乳液和反向胶束中酶催化技术的开发[3]以及分离蛋白质中的应用[4],使微乳液在生化技术研究中倍受青睐．与过剩盐水相和过剩油相达三相平衡时的微乳液即为中相微乳液。中相微乳液具有既可增溶水又可增溶油的特殊性质,并且微乳液与过剩水相和过剩油相间的界面张力（飞uw和7;n。;）极低顺干2．0。10－’1liN·111…     

DEA与SDS/n-C5H11OH/H2O微乳液的相互作用

以循环伏安法研究了N,N-二乙基苯胺（DEA）与十二烷基硫酸钠（SDS）/正戊醇（n-C5H11OH）/H2O体系O/W和W/O结构微乳液的相互作用.结果表明,DEA在SDS/n-C5H11OH/H2O体系微乳液中有两种定位方式:其一,DEA分子在微乳液液滴膜相中定位于表面活性剂和助表面活性剂的极性基团附近;其二,DEA分子在微乳液液滴膜相中定位于表面活性剂疏水基团一侧.两种定位的分布与微乳液的结构和组成相关.     

吩噻嗪在十二烷基硫酸钠/苯甲醇/水微乳液中的定位

采用循环伏安法和荧光猝灭法研究了吩噻嗪（PTZ）在十二烷基硫酸钠（SDS）/苯甲醇（BA ）/ 水（H2O）微乳液中的定位.结果表明,吩噻嗪在十二烷基硫酸钠/苯甲醇/水体系微乳液中位于微乳液膜相中靠近表面活性剂极性头基的一侧,PTZ分子中的S原子和N原子均可朝向表面活性剂的极性头基.     

逆微乳液体系研制镧系六铝酸盐甲烷燃烧催化剂

采用逆微乳液为媒介合成对甲烷燃烧有高温热稳定性又有催化活性的六铝酸镧催化剂的前躯体.分别用十二烷基磺酸钠(SDS)和十六烷基三甲基溴化铵(CTAB)作为表面活性剂,脂肪醇作助表面活性剂,分别用水和正辛烷作分散相和连续相,绘制四组分拟三元体系相图,考察影响微乳液形成和稳定的因素,选取形成微乳液的最佳条件和合适配比进行反应,在较低温度(1050℃)下焙烧转化成六铝酸盐催化剂,并考察和讨论了Fe,Mn金属离子取代的镧系同晶催化剂对甲烷燃烧催化活性的影响.     

逆微乳液法合成六铝酸盐甲烷燃烧催化剂

采用逆微乳液为媒介合成六铝酸盐及其金属取代系列甲烷燃烧催化剂.首先研制了由表面活性剂、助剂、油相和水相四组分逆微乳液拟三元体系相图,选择十六烷基三甲基溴化铵(CTAB)为表面活性剂,脂肪醇为助剂,正辛烷为油相和水相[或Al(NO3)3溶液].研究了助剂脂肪醇链长、表面活性剂与助剂相对量和盐浓度对微乳液体系形成和稳定性影响,并以电导率随水含量变化的规律很好地印证了微乳液体系的相行为.选取相图中稳定微乳区合成了具有高温稳定性的甲烷催化燃烧催化剂六铝酸镧[La(Mnx/Fex)Al12-xO19-δ].用BET、TG-DTA和XRD表征了催化剂的物性和结构,并在微型固定床反应器中考察了对甲烷燃烧的催化活性.结果表明,利用逆微乳液作为反应介质使催化剂前驱体分散更充分,使六铝酸盐晶相形成的温度有效地降低到950℃.Fe取代的六铝酸盐具有较好高温催化活性和热稳定性,而Mn取代的同晶体则具有较好的低温催化活性,Fe和Mn离子同时对Al3 进行取代时,由于两者之间存在的协同效应明显提高了催化剂的催化活性和比表面,T10仅为475℃,T90为660℃.     

A novel water-in-ionic liquid microemulsion and its interfacial effect on the activity of laccase

It is of great significance to develop an appropriate water-in-ionic liquid (W/IL) microemulsion suitable for the expression of the catalytic activity of a given enzyme. In this paper, the phase diagram of a new AOT/Triton X-100/H(2)O/[Bmim][PF(6)] pseudo ternary system is presented. With the aid of nonionic surfactant Triton X-100, AOT could be dissolved in hydrophobic ionic liquid [Bmim][PF(6)], forming a large single phase microemulsion region. The water-in-[Bmim][PF(6)] (W/IL) microemulsion domain was identified electrochemically by using K(3)Fe(CN)(6) as a probe. The existence of W/IL microemulsions was demonstrated spectrophotometrically by using CoCl(2) as a probe. New evidences from the FTIR spectroscopic study, which was first introduced to the W/IL microemulsion by substituting D(2)O for H(2)O to eliminate the spectral interference, demonstrated that there existed bulk water at larger ω(0) values (ω(0) was defined as the molar ratio of water to the total surfactant) in the W/IL microemulsion, which had remained unclear before. In addition to the inorganic salts, biomacromolecule laccase could be solubilized in the W/IL microemulsion. The laccase hosted in the microemulsion exhibited a catalytic activity and the activity could be regulated by the composition of the interfacial membrane.     

Electrochemical Oxidation of L-Cystenine in SDS／BA／H2O Microemulsion

The electrochemical oxidation of L-cysteine in an SDS/BA/H2O microemulsion system was studied with the methods of ultramicroelectrode cyclic voltammetry and AC impedance. The catalytic efficiency of the microemulsion on the electrochemical oxidation increases with the increase of BA or SDS content, but decreases with the increase of the water content because of the effects of BA, SDS and water on the solubilization of Lcysteine in the microemulsion. Furthermore, the catalytic efficiency of the bicontinuous structure is greater than that of an O/W microemulsion system. The results derived from both the rate constant k^0 and Gibbs free energy △G^≠ accord with those from the catalytic efficiency.     

负载金属催化剂Ir(γ-Al2O3)对阿维菌素选择加氢反应研究

分别采用氢气、NaBH₄、醇水混合溶剂还原, PVP(聚乙烯吡咯烷酮)保护和微乳液法制备了γ-Al₂O₃负载的Ir金属催化剂, 通过XPS、XRD、TEM对催化剂的结构进行了表征, 考察了催化剂对阿维菌素选择加氢制备伊维菌素的性能, 探讨了催化剂制备方法对催化剂活性和选择性的影响. 实验结果表明, 在不同金属催化剂Ru/γ-Al₂O₃、Pd/γ-Al₂O₃、Pt/γ-Al₂O₃、Ir/γ-Al₂O₃中, Ir/γ-Al₂O₃的活性和选择性最好. 用PVP保护的Ir/γ-Al₂O₃, 其催化活性和选择性比没有PVP保护的催化剂有显著提高; 采用微乳液法制备的Ir/γ-Al₂O₃催化剂显示出最好的活性, 但反应选择性比PVP保护的催化剂差.     

微乳液法制备的PtSn/C催化剂对乙醇的电催化氧化性能

以甲酸钠为还原剂,在水/triton X-100/乙二醇/环己烷的W/O型微乳液中制备PtSn/C催化剂.采用X射线衍射（XRD）分析催化剂的结构,循环伏安法和电化学阻抗谱法测试催化剂对乙醇的催化氧化性能.结果表明,微乳法制备的PtSn/C催化剂部分合金化,与Pt/C相比,PtSn/C对乙醇的电催化氧化活性有明显提高,具有更高的抗CO中毒能力.     

Structure and catalytic properties of nanosized alumina supported platinum and palladium particles synthesized by reaction in microemulsion

Mixtures of nanosized platinum and palladium particles have been prepared by reduction of salt-containing microemulsion droplets using hydrazine as the reducing agent. To avoid possible negative effects of the presence of sulfur compounds during the preparation the microemulsion was made using the sulfur-free nonionic polyoxyethylene 4 lauryl ether surfactant. Transmission electron microscopy showed that the as-prepared mixtures contained crystalline platinum particles of fairly homogeneous size (20 to 40 nm) with adsorbed amorphous palladium particles 2 to 5 nm in size. Catalyst samples were prepared by depositing the nanoparticles on a gamma-Al(2)O(3) support followed by heating in air at 600 degrees C. Alloyed particles of platinum and palladium with sizes ranging from 5 to 80 nm were obtained during the heating. The majority of the particles had the fcc structure and their compositional range was dependent upon the Pt:Pd molar ratio of the microemulsion. A catalyst prepared from a microemulsion with a 20:80 Pt:Pd molar ratio showed the highest catalytic activity for CO oxidation, while pure platinum and palladium catalysts showed higher sulfur resistance. These results differ from the performance of conventional wet-impregnated catalysts, where a 50:50 Pt:Pd molar ratio resulted in the highest catalytic activity as well as the highest sulfur resistance.     

The catalytic activity of bimetallic Pt—Pd polymer nanocomposites in formic acid oxidation

The platinum-palladium/Nafion metal—polymer nanocomposites were synthesized by chemical reduction of metal ions in water—organic reverse microemulsion solutions. The catalytic activity of the synthesized polymer composites with bimetallic Pt—Pd nanoparticles was estimated in the oxidation of hydrogen and formic acid.     

Formation of a novel type of reverse microemulsion system and its application in synthesis of the nanostructured La0.95Ba0.05MnAl11O19 catalyst

In the study, a novel microemulsion system, consisting of water, iso-propanol and n-butanol, was developed to synthesize the nanostructured La(0.95)Ba(0.05)MnAl(11)O(19) catalyst with high surface area and catalytic activity for methane combustion.     

Synthesis of hexaaluminate catalysts for methane combustion by reverse microemulsion medium

The aim of this study is to synthesize the catalysts of Fe- and Mn-substituted hexaaluminate by reverse microemulsion medium for methane catalytic combustion application. Pseudo-ternary phase diagrams in quaternary microemulsion systems of cetyltrimethylammonium bromide (CTAB), n-butanol, n-octane, and water [or Al(NO₃)₃ solution] were presented. The effects of the alcohol chain length, ratio of sur-factant to cosurfactant, and salt concentration on the formation and stability of microemulsion systems were studied. The phase behavior of microemulsion systems was confirmed through the varying of the conductivity with the water content. The performance and structure of the catalysts, La(Mn _x /Fe _x )Al_12−x ⁻ O_19-δ synthesized with the optimal parameter in the phase diagrams of microemulsions systems were characterized by BET, TG-DTA, and XRD. The micro fix-bed reactor was used to measure the catalytic activities of catalysts to methane combustion. The results showed that this synthesis method could yield non-agglomerated and highly dispersed precursors that would undergo crystallization at the lower temperature of 950°C. When temperature was raised up to 1050°C, the complete crystalline La-hexaaluminate was shaped. The hexaaluminate substituted with Fe had high-catalytic activity and stability at high temperature, while the Mn-substituted had higher catalytic activity at lower temperature. When the cooperation of Fe and Mn occurred, i.e., LaFeMnAl₁₀O_19−δ exhibited a high surface area and catalytic activity to CH₄ combustion, the CH₄ light-off temperature was only 475°C and the complete combustion temperature was 660°C. This was attributed to the synergistic effect between Fe and Mn. Supported by the National Natural Science Foundation of China (No. 20706004) and Beijing Natural Science Foundation (Nos. 2062017 and 8072018)     

Ce_(0.67)Zr_(0.33)O_2材料的制备和表征及其负载单Pd三效催化剂的性能

采用共沉淀法、均匀沉淀法、微乳法和水热法四种方法制备了铈锆固溶体(CZ),对其进行了X射线衍射和N2吸附脱附分析.以CZ为载体制备了负载单Pd三效催化剂,并对催化剂进行了氧化还原性能测试.结果表明,制备方法对CZ载体的物理、化学性能有显著的影响,而其负载单Pd催化剂的催化活性与CZ载体比表面积的大小没有明显的对应关系.采用共沉淀法制备的CZ载体具有相对良好的热稳定性以及储放氧能力,其负载单Pd催化剂在老化前后表面PdO物种有良好的还原性能,并表现出优异的三效催化性能.     

微乳液法制备固体催化剂在多相催化领域中的应用

采用微乳液法制备纳米粒子具有粒径可控、粒度分布均匀、粒子不易团聚等优点,在一些反应中表现出优良的催化性能.本文介绍了微乳液的概念,阐述了反相微乳体系(W/O)作为纳米反应器的原理以及用于制备固体催化剂的方法.综述了反相微乳液法制备固体催化剂在多相催化领域中的应用,并指出该技术存在的问题和发展趋势.