CeO2-ZrO2包覆石墨粉增强铝基复合材料的制备与耐蚀性能

采用非均匀成核法,在机械搅拌条件下通过硝酸亚铈和氧氯化锆水解生成无定形氧化铈、氧化锆对石墨进行表面包覆,利用扫描电镜、 X射线衍射和XPS对所得样品进行了表征,通过搅拌铸造法制备了氧化铈/锆包覆石墨颗粒增强铝基复合材料,并对复合材料耐蚀性能进行了初步研究. SEM和XPS表明,氧化铈/锆在石墨表面形成了均匀、致密的纳米级包覆层,氧化铈/锆通过与铝液的反应性润湿提高了石墨颗粒与铝液的润湿性,阻止了石墨与铝发生化学反应. 测试结果表明,氧化物的包覆基本抵消了由于石墨的添加而降低复合材料的腐蚀电位,也降低了腐蚀电流(两个数量级).     

TiO2包覆对LiCo1/3Ni1/3Mn1/3O2材料的表面改性

为了提高材料LiCo1/3Ni1/3Mn1/3O2的循环性能, 采用浸渍-水解法对其进行TiO2包覆. 用X射线衍射(XRD)、电化学交流阻抗谱(EIS)、电感耦合等离子体发射光谱(ICP-OES)和恒流充放电测试研究包覆材料的结构和电化学性能. TiO2仅在材料表面形成包覆层, 并未改变材料的结构. TiO2包覆能提高材料LiCo1/3Ni1/3Mn1/3O2的倍率性能和循环性能, TiO2包覆后的材料在5.0C(1.0C=160 mA·g-1)下的放电容量达到0.2C下的66.0%, 而包覆前的材料在5.0C下的放电容量仅为其0.2C下的31.5%. 包覆后的材料在2.0C下循环12周后的容量没有衰减, 而未包覆的材料容量保持率仅为94.4%. EIS测试表明包覆材料性能的提高是由于循环过程中材料的界面稳定性得到了提高. 循环后材料的XRD和ICP-OES测试表明, 包覆层能提高材料LiCo1/3Ni1/3Mn1/3O2的结构稳定性.     

TiO2包覆对LiCO1/3Ni1/3Mn1/3O2材料的表面改性

为了提高材料LiCo1/3Ni1/3MnO2的循环件能,采用浸渍-水解法对其进行TiO2包覆.用X射线衍射(XRD)、电化学交流阻抗谱(EIS)、电感耦合等离子体发射光谱(ICP-OES)和恒流允放电测试研究包覆材料的结构和电化学性能.TiO2仅在材料表面形成包覆层,并未改变材料的结构.TiO2包覆能提高材料LiCo1/3Ni1/3Mn1/3O2的倍率性能和循环性能,TiO2包覆后的材料在5.0C(1.0C=160 mA·g-1)下的放电容量达到0.2C下的66.0%,而包覆前的材料在5.0C下的放电容量仅为其0.2C下的31.5%.包覆后的材料在2.0C下循环12周后的容最没有衰减,而未包覆的材料容量保持率仅为94.4%.EIS测试表明包覆材料性能的提高是由于循环过程中材料的界面稳定性得到了提高.循环后材料的XRD和ICP-OES测试表明,包覆层能提高材料LiCo1/3Ni1/3Mn1/3O2的结构稳定性.     

包覆型磁性二氧化钛的制备及其光催化性能的研究

采用表面改性的方法分别制备了两种核-壳和核-壳-壳式结构的TiO2/γ-Fe2O3,TiO2/S iO2/γ-Fe2O3包覆型磁性二氧化钛.用XRD、TG-DTA、TEM、BET、和IR等手段对样品进行了结构表征,并研究了它们在紫外光照射下对甲基橙的降解性能.结果表明,在紫外光的照射下,包覆型磁性二氧化钛可有效地降解甲基橙;TiO2/S iO2/γ-Fe2O3的光催化活性优于TiO2/γ-Fe2O3,前者在循环使用三次后降解率仍不低于95%.     

Y_2O_3∶Eu荧光粉表面包覆In_2O_3的研究

采用高温固相法合成了FED用Y2O3∶Eu红色荧光粉,为提高其导电性,采用表面成膜包覆法对其进行了In2O3包膜研究。通过XRD,Zeta电位,SEM及低压光谱分析等检测手段分析了包膜前后Y2O3∶Eu的晶体结构、电位、形貌与发光性能,探索了包膜工艺。结果表明:在Y2O3∶Eu表面包覆3%的In2O3能有效改善荧光粉的发光亮度,这种改善的可能原因是包覆In2O3改善了Y2O3∶Eu晶粒表面的导电性。     

TiO_2颗粒表面无机包覆的研究进展

从表面处理的作用、过程、方法、种类、机理、影响因素等方面综述了二氧化钛颗粒无机包覆的研究进展 ,着重阐述了二氧化钛包硅、包铝的原理及工艺条件。     

新型负载配位催化剂ZBDPPEDAEPA／TiO2／Pd催化羰化反应研究

用乙二胺-N'-乙基膦酸的氨基与季盐[Ph2P+(CH2OH)2]Cl-,经曼尼希反应合成了N,N-双二苯膦甲基-乙二胺-N'-乙基膦酸(Ph2PCH2)2NCH2CH2N+H2CH2CH2PO3H-(BDPPEDAEPA), 并制备了相应的(N,N-双二苯膦甲基-乙二胺-N'-乙基膦酸-磷酸氢)锆载体Zr(HPO4)1.35[(Ph2PCH2)2NCH2CH2NHCH2CH2PO3]0.65·H2O (ZBDPPEDAEPA) 及二氧化钛和二氧化锆微粉表面包膜了ZBDPPEDAEPA的新型催化剂载体ZBDPPEDAEPA / TiO2、ZBDPPEDAEPA/ ZrO2和相应的钯催化剂ZBDPPEDAEPA / Pd、ZBDPPEDAEPA / TiO2 / Pd、ZBDPPEDAEPA/ZrO2/Pd. 在常压条件下, 对该类催化剂催化氯苄羰化反应的活性及产物组成作了初步考察. 对催化剂载体的粒径分析表明, ZBDPPEDAEPA / TiO2 / Pd的高活性归因于ZBDPPEDAEPA / TiO2载体的颗粒均匀、平均粒径小.ZBDPPEDAEPA以平均50 nm的薄层包膜在TiO2上, 这层包膜属于纳米级催化材料.     

Y2O3:Eu荧光粉表面包覆In2O3的研究

采用高温固相法合成了FED用Y2O3：Eu红色荧光粉，为提高其导电性，采用表面成膜包覆法对其进行了In2O3包膜研究。通过XRD，Zeta电位，SEM及低压光谱分析等检测手段分析了包膜前后Y2O3：Eu的晶体结构、电位、形貌与发光性能，探索了包膜工艺。结果表明：在Y2O3：Eu表面包覆3％的In2O3能有效改善荧光粉的发光亮度，这种改善的可能原因是包覆In2O3改善了Y2O3：Eu晶粒表面的导电性。     

TiO2颗粒表面无机包覆的研究进展

从表面处理的作用、过程、方法、种类、机理、影响因素等方面综述了二氧化钛颗粒无机包覆的研究进展,着重阐述了二氧化钛包硅、包铝的原理及工艺条件。     

纳米TiO2/高分子复合粒子的制备及表征

用水溶性的羟丙基纤维素(HPC)对纳米TiO2进行表面包覆,得到纳米TiO2/HPC粒子,再以硫酸铈铵[Ce(SO4)2·2(NH4)2SO4]作为引发剂,在纳米TiO2/HPC粒子表面进行HPC与甲基丙烯酸甲酯(MMA)的接枝聚合,最终得到纳米TiO2/HPC-g-PMMA复合粒子,实现了纳米TiO2的有机化改性.用IR, TEM和TG对复合粒子进行了一系列的测试与表征.     

Photocatalytic coatings for environmental applications

A series of nano- and micronparticle-grade anatase and rutile titanium dioxide pigments have been prepared with various densities of surface treatments, particle size and surface area. Their photocatalytic activites have been determined in a series of paint films by FTIR, chalking, color, gloss change and weight loss after artifical weathering. The pigments have also been examined by rapid assessment methodologies using photodielectric microwave spectroscopy, 2-propanol oxidation and hydroxyl analysis. The microwave response under light and dark cycles provides an extended timescale probe of charge-carrier dynamics in the pigments. Pigment particle size, surface area and properties clearly play an important role in dispersion and any polymer-pigment interactions. Photooxidation studies on several types of paint films show a clear demarcation between nanoparticle- and pigmentary-grade titanium dioxide, with the former being more active because of their greater degree of catalytic surface activity. The photosensitivity of titanium dioxide is considered to arise from localized sites on the crystal surface (i.e. acidic OH), and occupation of these sites by surface treatments inhibits photoreduction of the pigment by ultraviolet radiation; hence, the destructive oxidation of the binder is inhibited. Coatings containing 2-5% by weight alumina or alumina and silica are satisfactory for general-purpose paints. If greater resistance to weathering is desired, the pigments are coated more heavily to about 7-10% weight. The coating can consist of a combination of several materials, e.g. alumina, silica, zirconia, aluminum phosphates of other metals. For example, the presence of hydrous alumina particles lowers van der Waals forces between pigments particles by several orders of magnitude, decreasing particle-particle attractions. Hydrous aluminum oxide phases appear to improve dispersibility more effectively than most of the other hydroxides and oxides. Coated nanoparticles are shown to exhibit effective light stabilization in various water- and oil-based paint media in comparison with conventional organic stabilizers. Hindered piperidine stabilizers are shown to provide no additional benefits in this regard, often exhibiting strong antagonism. The use of photocatalytic titania nanoparticles in the development of self-cleaning paints and microbiological surfaces is also demonstrated in this study. In the former case, surface erosion is shown to be controlled by varying the ratio of admixture of durable pigmentary-grade rutile (heavily coated) and a catalytic-grade anatase nanoparticle. For environmental applications in the development of coatings for destroying atmospheric pollutants such as nitrogen oxide gases (NO(X)), stable substrates are developed with photocatalytic nanoparticle-grade anatase. In this study, porosity of the coatings through calcium carbonate doping is shown to be crucial in the control of the effective destruction of atmospheric NO(X) gases. For the development of microbiological substrates for the destruction of harmful bacteria, effective nanoparticle anatase titania is shown to be important, with hydrated high surface area particles giving the greatest activity.     

Probing the effects of interfacial chemistry on the kinetics of phase transitions in amorphous and tetragonal zirconia nanocrystals

In this work, we examine the phase stability of both uncoated and alumina-coated zirconia nanoparticles using in-situ X-ray diffraction. By tracking structural changes in these particles, we seek to understand how changing interfacial bonding affects the kinetics of amorphous zirconia crystallization and the kinetics of grain growth in both initially amorphous and initially crystalline zirconia nanocrystals. Activation energies associated with crystallization are calculated using nonisothermal kinetic methods. The crystallization of the uncoated amorphous zirconia colloids has an activation energy of 117 +/- 13 kJ/mol, while that for the alumina-coated amorphous colloids is 185 +/- 28 kJ/mol. This increase in activation energy is attributed to inhibition of atomic rearrangement imparted by the alumina coating. The kinetics of grain growth are also studied with nonisothermal kinetic methods. The alumina coating again dramatically affects the activation energies. For colloids that were coated with alumina when they were in an amorphous structure, the coating imparts a 5x increase in the activation energy for grain growth (33 +/- 8 versus 150 +/- 30 kJ/mol). This increase shows that the alumina coating inhibits zirconia cores from coarsening. When the colloids are synthesized in the tetragonal phase and then coated with alumina, the effect of surface coating on coarsening kinetics is even more dramatic. In this case, a 10x increase in activation energies, from 28 +/- 3 kJ/mol for the uncoated particles to 300 +/- 25 kJ/mol for the alumina-coated crystallites, is found. The results show that one can alter phase stability in colloidal systems by using surface coatings and interfacial energy to dramatically change the kinetic barriers to structural rearrangement.     

Characterization of covalently bonded and adsorbed polymer coatings on silica, alumina and zirconia by means of physico-chemical and chromatographic methods

Polymer coatings on porous silica, alumina and zirconia were prepared by covalent bonding of a copolymer of styrene and vinylsilane on the oxidic surface with or without subsequent cross-linking of the immobilized polymeric layer. Polybutadiene and polychloromethylstyrene were adsorbed on the surface of porous alumina without covalent bonding and were cross-linked after deposition. Analysis of the pore structure of coated oxides by means of nitrogen adsorption, mercury porosimetry and inverse size-exclusion chromatography revealed different polymer distributions across the modified surface and different changes of the porosity of the initial oxides depending on the method of polymer immobilization. By covalent bonding of the copolymer of styrene and vinylsilane to alumina and zirconia with subsequent cross-linking the modifying polymeric layer, highly hydrolytic stable packings were synthesized and their application in separations with aggressive eluents were demonstrated.     

Fe3+-TiO2/SiO2薄膜催化剂的结构对其光催化性能影响

以硅胶为载体,采用溶胶-凝胶法制备了掺杂不同量Fe3+的TiO2光催化剂(Fe3+-TiO2/SiO2),以氙灯为光源,罗丹明B为目标降解物,对其光催化活性进行了研究.结果表明,Fe3+-TiO2/SiO2比TiO2纳米粉有更好的催化活性,Fe3+的最佳掺入量为0.03％.罗丹明B在粉体和膜催化剂的作用下遵循不同的光催化反应机理.根据XRD,SEM,Raman,XPS和FTIR的表征结果可认为,TiO2在SIO2表面薄膜化和Ti-O-Si键的形成是催化活性提高和降解机理不同的主要原因.     

Characterization of ZrO2- Al2O3mixed oxides support prepared by urea hydrolysis

The characteristics of Al₂O₃, ZrO₂ and three binary mixtures of ZrO₂-Al₂O₃ were studied by determining their BET surface areas, micropore surface area, total pore volume, adsorption-desorption isotherms, the X-ray diffractogram, surface acidity and catalytic functionality for cumene cracking. The XRD results show that the incorporation of alumina into the zirconia from 50% and beyond renders it amorphous. Furthermore, the mixed oxide containing 50% alumina and 50% zirconia had the highest BET surface area of 199.9 m²/g whilst pure zirconia had the lowest BET surface area of 37.19 m²/g. The pores for all the mixed oxides were found to be monomodal and zirconia pores were more open. The results of the acidity measurements and cumene cracking functionality indicates that whilst pure zirconia has low total acidity, the incorporation of alumina increases its acidity through a synergistic effect. This revised version was published online in June 2006 with corrections to the Cover Date.     

TiO2在水及丙二醇介质中表面电性质的研究

0引言 固体颗粒在液相介质中的分散是基础研究领域和工业技术部门普遍遇到的问题 ?在化学工业领域,如涂料 ? 染料 ? 油墨 ? 化妆品等,固体颗粒的分散及分散稳定性直接影响着产品的质量和性能 ?TiO 2 颗粒的水基分散体系广泛应用于涂料 ? 油墨以及化妆品中,也是陶瓷制备过程中重     

聚多巴胺辅助的液相沉积法制备二氧化钛涂层毛细管柱及其在电色谱中的应用

利用多巴胺的自氧化聚合反应在毛细管内壁引入聚多巴胺涂层,并以聚多巴胺涂层作为连接臂辅助二氧化钛前躯体氟钛酸铵液相沉积制备了二氧化钛涂层毛细管柱。该方法制备过程简单,条件温和,形成的涂层稳固。采用X射线光电子能谱(XPS)、扫描电镜(SEM)和测定电渗流变化对涂层性质进行了表征。选择5种阴离子、生物碱作为分离对象,考察了缓冲液组成、浓度和p H值等因素对该涂层柱毛细管电色谱分离性能的影响。结果显示,在优化条件下,5种阴离子及生物碱在该涂层毛细管柱上均能得到较好的分离。     

Tentative links between thermal diffusivity and fire-retardant properties in poly(methyl methacrylate)-metal oxide nanocomposites

Possible relationships between fire-retardant properties and thermal diffusivity for poly(methyl methacrylate) (PMMA) filled by melt blending with titanium dioxide (TiO₂), alumina (Al₂O₃) and boehmite (AlOOH) were investigated for a better understanding of the mode of action of metal oxides as fire-retardants (FR) in PMMA. Fire-retardancy was measured with a cone calorimeter and thermal diffusivity (α) by Laser Flash Analysis (LFA). LFA measurements have shown that heat dispersion is higher with titanium dioxide and boehmite than with alumina despite a larger surface area. For thermal diffusivity, discrepancies between the different nanofillers were only visible from 10 wt% onwards. Thermal degradation of PMMA-oxide nanocomposites and their thermal diffusivity could be linked. Moreover, a bi-linear relationship between the peak of heat release rate (pHRR) and the average of heat release rate (AHRR) showed the occurrence of a barrier effect.     

氧化铝对Pt-SO4^2-／ZrO2-Al2O3固体酸催化剂结构与酸性的影响

通过混捏法制备了Pt-SO4^2-／ZrO2-Al2O3固体酸催化剂，考察了该催化剂在正构烷烃低温异构化反应中的催化稳定性．采用X射线衍射、差热分析、X射线光电子能谱、核磁共振、N2吸附-脱附和微量热等表征技术，对氧化铝的作用机理进行了研究．结果表明，氧化铝起到结构助催化剂作用，对四方相氧化锆具有稳定作用，并延迟了氧化锆的晶化，抑制了氧化锆的烧结，从而增大了催化剂的比表面积和孔容．XPS结果表明，Zr3d峰向低结合能方向移动，Al2p峰向高结合能方向移动，说明Al^3＋的电子向Zr^4＋偏移．微量热结果表明氧化铝的引入提高了催化剂的酸量和酸强度．^27Al固体核磁共振结果表明，Pt-SO4^2-／ZrO2-Al2O3中的六配位铝的结构发生了变化．氧化铝的引入还可能有助于氧化锆晶格缺陷的形成，焙烧过程中Al^3＋迁移进入氧化锆晶格并同晶取代Zr^4＋形成氧缺陷位，这些氧缺陷位在S=O键诱导下显示强酸性．