具有三维贯通多级孔道结构大孔氧化铝的制备与表征

采用铝溶胶晶种引入、结合相分离的方法制备了具有三维贯通多级孔道结构的大孔氧化铝材料。采用扫描电镜（SEM）、X射线衍射（XRD）、N₂吸附-脱附、压汞、核磁共振波谱（NMR）等测试方法对所得材料进行了表征。结果表明,该氧化铝材料具有200-600 nm的均匀分布且贯通的连续大孔孔道,经550℃焙烧即可得到结晶态γ-氧化铝。大孔氧化铝比表面积达到366 m²/g,具有以5 nm及400 nm为中心的较为集中的介孔-大孔多级孔道分布。焙烧后的样品中,铝具有四、六两种配位状态。制备过程中,聚环氧乙烷（PEO）作为诱导剂引发固-液两相分离,形成具有三维贯通多级孔道结构大孔氧化铝,而凝胶中引入铝溶胶时,AlOOH晶粒与铝交联水合物均相伴生,在凝胶过程诱导铝交联水合物转变为AlOOH,最终使大孔氧化铝在较低的焙烧温度即可转化为γ-氧化铝。     

炭化温度对模板法合成介孔炭性能的影响

以蔗糖为炭源和硅酸钠为硅源,采用原位共聚法制备了炭/氧化硅复合体,除去氧化硅得到介孔炭材料.采用N2吸附-脱附、透射电子显微镜和红外光谱对不同炭化温度获得的样品进行表征.结果表明,随着炭化温度升高,所得的介孔炭比表面积和孔容均下降,650℃ ～ 950℃的炭化温度下获得的样品BET比表面积在586m2/g ～728 m2/g之间,孔容在0.549cm3/g～0.696cm3/g之间,孔径分布5-15nm之间.经红外光谱检测所得的介孔炭样品均含有氢和氧的功能团.     

负载Ni金属有序介孔氧化铝催化剂的制备及表征

采用原位合成法和传统浸渍法以价格低廉的硝酸铝作为铝源, 聚乙二醇1540为模板剂, 硝酸镍为镍源, 制备出负载Ni金属有序介孔氧化铝催化剂, 并采用BET、TEM、XRD、TG多种测试技术对合成催化剂的物理化学性质和结构特征进行了表征. 实验结果表明, 两种方法均能制备出比表面积大(＞210 m2·g-1)、孔径分布窄(4 nm左右)的负载Ni金属介孔氧化铝催化剂. 与浸渍法相比, 原位合成法所制备的负载Ni金属有序介孔氧化铝镍离子与载体具有更强的相互作用力, 且孔结构具有一定的有序性.     

高比表面积蠕虫状介孔SnO2的合成与表征

 以聚乙二醇 (PEG) 为模板剂, 氯化锡为锡源, 尿素为沉淀剂, 采用水热法合成出高比表面积的蠕虫状介孔四方相金红石型 SnO2. 考察了 PEG 分子量及其浓度、水热温度和焙烧温度对 SnO2 孔结构和形貌的影响. 采用 X 射线衍射、N2 吸附-脱附、透射电镜、红外光谱和紫外-可见光谱等技术对样品进行了表征. 结果表明, 模板剂可被水洗除去, PEG 分子量对介孔 SnO2 的比表面积影响不大, 而 PEG 浓度、水热温度和焙烧温度的影响较大. 在以分子量为 6000 的 PEG 与 Sn 的摩尔比为 0.01 的条件下, 于 120 oC 水热处理 29 h 后可合成出比表面积高达 161 m2/g 和平均孔径为 2.6 nm 的蠕虫状介孔 SnO2. 所制得样品具有较好的紫外光吸收性能, 适宜用作催化剂、载体和气体传感器等.     

碱处理脱硅与提高Y型分子筛硅铝比——矛盾的对立与统一

考察了 "水热处理"以及"碱处理+水热处理"两种方法所制得的超稳 Y 分子筛的骨架硅铝比、孔结构特征以及酸量, 并探讨了"碱处理+水热处理"方法对起始 NaY 分子筛的适应性. 结果表明, 在水热处理前, 对 NaY 分子筛进行碱处理脱硅可在不改变最终样品的骨架超稳化水平和酸量的同时, 样品的介孔体积显著增加. 直接水热处理 NaY 分子筛所得样品介孔体积不超过 0.14 cm3/g, 而先碱处理后水热处理, 所得样品介孔体积可达 0.22 cm3/g. 该法适用于制备骨架硅铝比高的 NaY 分子筛. 起始原料的骨架硅铝比较低时, 所得样品的介孔体积增幅小, 而且微孔受损严重.     

介孔氧化铝的制备及其在甲醇脱水制二甲醚反应中的应用

以硝酸铝为铝源,以十六烷基三甲基溴化铵为阳离子模板剂,采用均匀沉淀法成功制得热稳定性较高和高度有序的介孔Al2O3(其比表面积179.8 m2/g,孔径5.4 am,孔体积0.3 cm3/g),并用于甲醇脱水制二甲醚反应中.结果表明,在280℃,液时空速为30 h-1条件下,甲醇转化率为90.2%,二甲醚时空收率最高可...     

有序介孔氧化铝的制备及其在丁烯歧化中的应用

采用有机铝源及阴离子模板剂制备了高比表面积、大孔容、窄孔径分布的有序介孔氧化铝(Al₂O₃)载体, 研究了铝源水解速率、模板剂碳链长度以及洗涤介质等因素对有序介孔氧化铝载体合成的影响。实验结果表明,提高铝源水解速率和用乙醇溶剂洗涤Al₂O₃前躯体都有利于Al₂O₃载体形成有序介孔结构,所得Al₂O₃载体的孔径和孔体积随着模板剂碳链长度的增加而增大。分别用有序介孔Al₂O₃和普通介孔Al₂O₃为载体,采用浸渍法负载氧化铼(Re₂O₇)制备了铼基催化剂,并用于评价丁烯歧化合成丙烯的反应性能。实验结果表明,铼基有序介孔催化剂(Re/OMA)的丁烯歧化性能显著优于普通铼基介孔催化剂(Re/MA),丁烯转化率高于50%,丙烯选择性约60%,丙烯收率达30%,催化剂寿命明显延长。     

介孔氧化铝的溶胶-凝胶法制备

以硝酸铝为铝源,十六烷基三甲基溴化铵和尿素为复合模板剂,采用溶胶-凝胶法制备了介孔氧化铝（1）,其结构经TEM, XRD, TG-DTA和N₂-BET表征。结果表明：1比表面积较大（＞400 m²·g^-1）,孔径分布窄(3～5 nm),形成的蠕虫状孔道具有短程有序性。     

介孔分子筛V-MCM-41的水热法制备与合成机理

 以十六烷基三甲基溴化铵为模板剂,廉价的工业级高模数比(3.3)的硅酸钠为硅源,通过水热法合成了V-MCM-41介孔分子筛. 考察了合成条件对产物织构的影响,并采用低温氮吸附法分析探讨了介孔分子筛V-MCM-41的合成机理. 结果表明,模板剂用量、 pH值、加料方式、晶化温度、晶化时间、陈化时间和焙烧气氛等合成条件对介孔分子筛的制备均有影响,其中晶化温度、 pH值和模板剂用量的影响最为明显. X射线衍射谱表明合成的介孔分子筛具有六方晶体结构. 红外光谱和紫外可见光谱表明V进入了介孔分子筛的骨架结构.     

乙二胺和聚乙二醇在纳米介孔氧化铝制备中的协同导向作用

以无机铝盐Al(NO₃)₃为原料, 以乙二胺和聚乙二醇为协同模板导向剂, 与氨水反应, 经过“沉淀-超声-煅烧”等过程, 制得介孔纳米氧化铝. 用TEM, XRD, N₂吸附-脱附等测试技术对样品进行了测试和表征. 研究结果表明, 所得样品具有相当高的比表面积(510 m²•g^－1)、较大孔容(1.13 cm³•g^－1)和较为集中的孔径(5.8 nm)分布. 根据乙二胺和氧化铝表面的溶液化学反应及在不同pH条件下的溶液组分分布, 探讨了它们在介孔氧化铝制备过程中的协同模板作用机理.     

High surface area, mesoporous, glassy alumina with a controllable pore size by nanocasting from carbon aerogels

A strategy to synthesize amorphous, mesoporous alumina by nanocasting has been developed, involving carbon aerogel as a hard template and aluminum nitrate solution as an alumina precursor. The alumina generated exhibits small, transparent granules with a 3-6 mm diameter and has inherited the three-dimensional network structure of the carbon template. The mesopore surface area of the alumina can be as high as 365 m2 g(-1), and the pore volume reaches 1.55 cm3 g(-1) after calcination at 600 degrees C in air for 8 h. The pore parameters can be varied within a certain range by variation of the carbon aerogel template and the loading amount of the alumina precursor. At high loadings, the obtained glassy alumina clearly has a bimodal pore size distribution in the mesopore range.     

Using collagen fiber as a template to synthesize hierarchical mesoporous alumina fiber

Hierarchical mesoporous alumina fiber was synthesized by using collagen fiber as the template, and characterized by means of scanning electron microscopy, transmission electron microscopy, N2 adsorption techniques, X-ray photoelectron spectroscopy, and X-ray diffraction. The alumina fiber obtained is approximately 1-4 microm in outer diameter and 0.5-1 mm in length. The pore size distribution of the alumina fiber is narrow (2-20 nm), and its pore size is controllable by varying preparation methods. This study indicates that collagen fiber, which has hierarchical supermolecular structure, could be used as an ideal template to prepare well-defined porous metal oxide fibers.     

Facile synthesis for ordered mesoporous gamma-aluminas with high thermal stability

The facile synthesis of highly ordered mesoporous aluminas with high thermal stability and tunable pore sizes is systematically investigated. The general synthesis strategy is based on a sol-gel process associated with nonionic block copolymer as templates in ethanol solvent. Small-angle XRD, TEM, and nitrogen adsorption and desorption results show that these mesoporous aluminas possess a highly ordered 2D hexagonal mesostructure, which is resistant to high temperature up to 1000 degrees C. Ordered mesoporous structures with tunable pore sizes are obtained with various precursors, different acids as pH adjustors, and different block copolymers as templates. These mesoporous aluminas have large surface areas (ca. 400 m2/g), pore volumes (ca. 0.70 cm3/g), and narrow pore-size distributions. The influence of the complexation ability of anions and hydro-carboxylic acid, acid volatility, and other important synthesis conditions are discussed in detail. Utilizing this simple strategy, we also obtained partly ordered mesoporous alumina with hydrous aluminum nitrate as the precursor. FTIR pyridine adsorption measurements indicate that a large amount of Lewis acid sites exist in these mesoporous aluminas. These materials are expected to be good candidates in catalysis due to the uniform pore structures, large surface areas, tunable pore sizes, and large amounts of surface Lewis acid sites. Loaded with ruthenium, the representative mesoporous alumina exhibits reactant size selectivity in hydrogenation of acetone, D-glucose, and D-(+)-cellobiose as a test reaction, indicating the potential applications in shape-selective catalysis.     

介孔氧化铝的研究进展

介孔氧化铝（MA）是比表面积超过350m²/g，孔径在2－50nm之间且孔径分布较窄的多孔氧化铝。这一新型氧化铝有望在催化剂及其它化学领域得到广泛应用，对材料科学及其应用有着重要意义。本文较全面地综述了近年来MA研究的最新进展，讨论了MA的各种合成路径和后处理方法，包括中性合成路径、阴离子合成路径和阳离子合成路径；结合XRD、氮吸附平衡等温线、TEM、²⁷Al魔角旋转核磁共振等图表对MA的结构和表征方法进行了阐述；探讨了MA作为催化剂载体和作为吸附剂的应用研究状况，并对今后的研究方向进行了展望。     

铝膜腔体内高度有序的介孔硅SBA-16的合成

在阳极铝膜腔体内, 以三嵌段聚合物F127为表面活性剂合成出一维纳米介孔二氧化硅材料. 采用压力诱导合成方法能使纳米纤维沿着铝膜腔体有序生长排列, 并且只存在于铝膜的腔体内, 在铝膜表面没有残留. 在纳米纤维的两侧可以清楚地观察到具有六边形结构的孔道, 直径为12 nm. 考察了正硅酸乙酯的水解时间以及化合物的不同配比对材料形貌的影响.     

Study on the capacity of mesoporous alumina with different pore sizes absorb silane inhibitors

By modifying and optimizing the procedures, which were well described and understood for the synthesis of macroporous alumina, mesoporous alumina–based film has been successfully prepared, In this paper, the orderly mesoporous Al₂O₃ thin film was prepared by electrochemical workstation, and via supported N‐octyltriethoxysilane (NOS) coupling agent, corrosion inhibitors be loaded into the different pore sizes of mesoporous alumina films. The physicochemical properties of this thin inhibitors carrier film were characterized. Corrosion resistance of mesoporous alumina and honeycomb ceramic macroporous alumina were compared; the conclusion shows that mesoporous alumina film can be used as good corrosion inhibitors carrier and bring out a high‐efficiency inhibition result. Simultaneously, by compared with corrosion inhibition of different pore sizes (20‐50 nm) mesoporous alumina who absorbed NOS, and a general relationship between the different mesoporous alumina pore sizes and the adsorption capacity of NOS was obtained.     

Interface chemistry of nanostructured materials: ion adsorption on mesoporous alumina

This paper presents a part of our work on understanding the effect of nanoscale pore space confinement on ion sorption by mesoporous materials. Acid-base titration experiments were performed on both mesoporous alumina and alumina particles under various ionic strengths. The point of zero charge (PZC) for mesoporous alumina was measured to be approximately 9.1, similar to that for nonmesoporous alumina materials, indicating that nanoscale pore space confinement does not have a significant effect on the PZC of pore surfaces. However, for a given pH deviation from the PZC, (pH-PZC), the surface charge per mass on mesoporous alumina was as much as 45 times higher than that on alumina particles. This difference cannot be fully explained by the surface area difference between the two materials. Our titration data have demonstrated that nanoscale confinement has a significant effect, most likely via the overlap of the electric double layer (EDL), on ion sorption onto mesopore surfaces. This effect cannot be adequately modeled by existing surface complexation models, which were developed mostly for an unconfined solid-water interface. Our titration data have also indicated that the rate of ion uptake by mesoporous alumina is relatively slow, probably due to diffusion into mesopores, and complete equilibration for sorption could take 4-5 min. A molecular simulation using a density functional theory was performed to calculate ion adsorption coefficients as a function of pore size. The calculation has shown that as pore size is reduced to nanoscales (<10 nm), the adsorption coefficients of ions can vary by more than two orders of magnitude relative to those for unconfined interfaces. The prediction is supported by our experimental data on Zn sorption onto mesoporous alumina. Owing to their unique surface chemistry, mesoporous materials can potentially be used as effective ion adsorbents for separation processes and environmental cleanup.     

具有结晶孔壁介孔镁锌氧复合物(英文)

以介孔碳为硬模板经过二次填充制备了介孔镁锌氧复合物.采用X射线衍射(XRD),透射电镜(TEM),扫描电镜(SEM),N2吸附脱附等手段对材料的结构及形貌进行了表征.结果表明,所制备的材料在具有高有序介孔结构的同时还具有结晶的孔壁.孔径尺寸均为4.0nm,比表面积均为114.5m2.g-1.广角XRD结果初步表明,材料中氧化镁和氧化锌复合形成了固溶体.该材料作为一种半导体材料有望在光学器件领域获得新的应用价值.     

Effects of calcination temperature on the pore size and wall crystalline structure of mesoporous alumina

In this paper, mesoporous alumina with different pore sizes and wall crystalline structures was synthesized at calcination temperatures over 550 degrees C. The characterization of the samples calcined at 550, 800, 1100, and 1300 degrees C, respectively, was performed using TEM, XRD, FTIR, TG/DTA, and N2 adsorption/desorption techniques. The correlation between pore size and wall crystalline structure on calcination temperature was systematically investigated.