Determination of wear metals in lubricating oils by flame atomic absorption spectrophotometry

A simple, rapid and reliable method was developed for the determination of copper, nickel, iron and lead in fresh and used lubricating oil samples by flame atomic absorption spectrophotometry (FAAS). In the present study, a mixture of organic solvents containing propionic acid and iso-butylmethyl ketone (1: 1) was used to extract the metals from lubricating oil samples followed by FAAS analysis. Aqueous standard solutions can be easily employed with the proposed mixed solvent system instead of organometallic standards. The analytical results obtained by employing the proposed solvent extraction system were found to be in good agreement with the results for aqueous media obtained after the destruction of oil samples matrix. Percentage recovery studies showed 88–98% for Cu, 92–95% for Fe, 96–106% for Ni and 84–100% for Pb with relative standard deviation of 2–6%. The developed method was effectively applied to routine determination of Cu, Ni, Fe, and Pb in lubricating oil samples.     

Analysis of metal ions in crude oil by reversed-phase high performance liquid chromatography using short column

In this study a rapid, simultaneous analysis of V, Ni, Fe and Cu in crude oil was achieved by high performance liquid chromatography using 10 cm length reversed-phase C18 column. Since the amount of metal ions is at a very low level, in this work, solvent extraction of metals by a ligand such as 8-hydroxyquinoline from acidic media was investigated with some modification to previous procedures. Average extraction recoveries were 99, 85, 94 and 96 for V, Ni, Fe and Cu, respectively. The proposed method was successfully applied to the crude oil which was obtained from Koshk area in southern Iran. Fast analysis of metal ion in reversed-phase short column was achieved with methanol/water (55/45, v/v) and the detection limits measured as three times the background noise were obtained. Also it was shown that if small amount of 8-hydroxyquinoline was added to the mobile phase, the peak height and the peak symmetry were improved. A typical chromatogram for the separation of the 8-hydroxyquinoline complexes of V (V), Ni (II), Fe (III) and Cu (II) in crude oil was obtained in less than 4 min.     

Demetalization of oils resulting from recycled tires by liquid-liquid extraction using modified superheated water An environmentally friendly approach

An approach based on continuous pressurized liquid-liquid extraction with 20% HNO₃/1 M KCl/10⁻³ M EDTA as extractant has been developed for the extraction of metals from the oil resulting from recycled tires. A multivariate optimization of the main variables affecting the extraction process has been performed. The method has been applied to three oil samples with different contents in V, Ni, Zn, Fe and Cu. The target metals have been determined in both untreated and treated oil by flame atomic absorption spectrometry (FAAS) in order to obtain the extraction efficiency. Under the optimum conditions, recoveries higher than 90% have been obtained with a repeatability and within-laboratory reproducibility, expressed as relative standard deviations, ranging from 2.75 to 6.91 and 2.97 to 8.16%, respectively. For applications where the demetalization does not require being complete, a study of the demetalization degree achieved depending on the extraction temperature and extractant composition has also been performed. This study provides useful data about the cheapest working conditions to be used in order to obtain a given demetalization level.     

Application of p-xylenesulphonic acid as ashing reagent in the determination of trace metals in crude oil

The p-xylenesulphonic acid ashing procedure was applied to the determination of Ca, Cu, Fe, Mg, Na, Ni and Zn in crude petroleum. The optimum acid ratio was 1.0 g per gram of oil for determining Na and Ni and 0.5 g per gram of oil for the other metals determined. The simultaneous ignition of the oil-acid mixture while boiling prevented volatilization losses for Fe, Na and Ni, eliminated the coke residue and reduced the ashing time. The minimum sample size for efficient metal release was 15.0 g. Satisfactory recoveries of added Na and Ni and highly reproducible results were obtained. Results obtained by this method were similar to those obtained by standard methods for the same samples.     

Trace elemental characterization of edible oils by ICP-AES and GFAAS

A method for the determination of the inorganic profile in edible oils is proposed. The quantification of selected metals in various oils (olive, pumpkin seed, sunflower, sesame seed, hazelnut, grape, soya, rice oil) was carried out using microwave assisted digestion followed by ICP-AES and GFAAS. The detection power of the ICP-AES technique was sufficient for the determination of Ca, Fe, Mg, Na, and Zn. Since the samples contained very low amounts of Al, Cu, Co, Cr, K, Ni, Mn, and Pb, these elements were measured by GFAAS. Differences of metal concentrations for edible oils obtained in this preliminary study represent a starting basis for the development of an additional analytical procedure applicable for oil characterization.     

煎煮对几种特色南药中重金属元素含量和形态影响

考察了几种特色南药中重金属(Cd,Cr,Cu,Fe,Mn,Ni,Pb,Sr,Zn)的含量状况,并采用形态连续萃取法分析重金属在药材中的形态分布,研究了药材煎煮时药材中重金属的释放及煎煮过程对药材中重金属形态分布的影响。结果表明,几种南药中Cr,Pb,Zn的含量较高,且巴戟天中的重金属总量高于限量标准;原药材中Cr,Cu,Mn,Ni,Pb和Zn主要存在于有机态和残留态,Fe和Sr主要存在于残留态。煎煮使南药中大量重金属迁移到药汤中;药汤中Cu,Mn,Cr,Pb和Zn主要来自于其在药材中的可交换态、碳酸盐结合态和有机态,而药汤中Sr,Ni和Fe不仅包含其非残留态,更多来自于它们的残留态。为减少药汤中重金属,对于Cu,Mn,Cr,Pb和Zn既要控制在药材中的总量,且需降低它们在药材中的非残留态含量;对于Fe,Ni和Sr则主要是控制其在药材中的总量。     

Cloud point extraction of trace metals from seawater and determination by electrothermal atomic absorption spectrometry with iridium permanent modifier.

A simple method is described for preconcentration and separation of trace metals such as Ag, Co, Cr, Cu, Fe, Mn, Ni and Pb simultaneously from seawater using a cloud point extraction (CPE) procedure. Triton X-114 nonionic surfactant and ammonium pyrrolidine dithiocarbamate (APDC) have been used as an extraction medium and a chelating extractant, respectively. The amounts of Triton X-114 and APDC and the pH value necessary for extraction were carefully optimized. The preconcentration factor of about 200 is achieved for all the studied metals. Electrothermal atomic absorption spectrometry (ETAAS) with an Ir coated graphite tube as permanent chemical modifier has been used for determination. The limits of detection of Ag, Co, Cr, Cu, Fe, Mn, Ni and Pb were 0.003, 0.008, 0.003, 0.006, 0.015, 0.002, 0.009 and 0.01 ng ml-1, respectively. Certified reference materials such as CASS-4 and NASS-5 (seawater) and NIST-1640 (natural water) have been used for validation of the new method. The relative standard deviation (%) obtained for all the metals are in the range 0.8 - 3.6% for natural water and 11-25% for seawater materials, except for Co in NASS-5 for which it was 50%.     

Determination of Copper,Nickel and Cadmium by Faas After Preconcentration with Zinc-Piperazinedithiocarbamate Loaded on Activated Carbon by Solid-Phase Extraction

ABSTRACT

A method was developed for the preconcentration of copper, nickel and cadmium in water samples, prior to their determination by FAAS, using the Zn-piperazinedithiocarbamate complex (ZnPDC) loaded on activated carbon. In this method, Cu, Ni and Cd in liquid phase quantitatively replaced zinc on a ZnPDC-activated carbon solid phase. Afterwards, the metals on the solid phase were easily eluted by Hg (II) solution into aqueous phase, and were measured by FAAS. The optimum experimental parameters such as pH, sample volume, and effect of matrix ions for the preconcentration of the metals were investigated. The range of linearity 0-6, 0-5, 0-3 μgml^?1, correlation coefficient 0.998, 0.996, 0.999, detection limits 15.7, 23.5, 11.8 ngml^?1 and determination limits 136, 179, 98 ngml^?1 in final Hg(II) solution were obtained for Cu, Ni and Cd, respectively. The proposed method has been employed for the determination of Cu, Ni and Cd in various standard metal alloys and natural water samples.     

Extractive concentration of platinum-group elements and their determination by atomic-absorption spectrophotometry

The extraction of Pt, Pd, Ir, Rh, Ru, Ag, Au, Co, Cu, Ni and Fe with n-octylaniline has been investigated. Noble metals are extracted 10(3)-10(4) times better than Cu, Ni, Co and Fe. A method of determination of Pt, Pd, Ir, Rh and Ru is proposed. They are first separated from Cu, Ni, Co and Fe by means of extraction (and then determined, in either the aqueous or organic phase, by atomic-absorption spectrophotometry. The atomic absorption of platinum metals (with the exception of Pd) is affected by other elements of the platinum group and by non-noble metals. La(NO(3))(3) and Nd(NO(3))(3) lower the limit of detection for Pt, Rh, Ir and Ru and inhibit the effect of Co, Cu, Ni, Fe, Bi, Zn, Na, etc. on their determination. Lanthanum and neodymium chlorides and sulphates produce a similar effect but only on the determination of Pt and Rh. The coefficient of variation of the determination, in both phases, is within 2-6.8%.     

Extraction and exchange behavior of metal species in therapeutically applied peat

The binding and availability of metals (Al, Ca, Cd, Co, Cr, Cu, Fe, Mg, Mn, Ni, Pb, Zn) in therapeutically applied peat (Grosses Gifhorner Moor, Sassenburg/North Germany) was characterized by means of a versatile extraction approach. Aqueous extracts of peat were obtained by a standardized batch equilibrium procedure using high-purity water (pH 4.5 and 5.0), 0.01 mol l(-1) calcium chloride solution, 0.01 mol l(-1) ethylenediaminetetraacetic acid (EDTA) and 0.01 mol l(-1) diethylenetriamine pentaacetic acid (DTPA) solution as metal extractants. In addition, the availability of peat-bound metal species was kinetically studied by collecting aliquots of extracts after different periods of extraction time (5, 10, 15, 30, 60 and 120 min). Metal determinations were performed by atomic spectrometry methods (AAS, ICP-OES) and dissolved organic matter (DOM) was characterized by UV/Vis measurements at 254 and 436 nm, respectively. Of the extractants studied Ca, Mg and Mn were the most available metals, in contrast to peat-bound Fe and Al. The relative standard deviation s(r) of the developed extraction procedures was mostly in the range of 4 to 20%, depending on the metal and its concentration in peat. A pH increase favored the extraction of metals and DOM from peat revealing complex extraction kinetics. Moreover, a competitive exchange between peat-bound metal species and added Cu(II) ions showed that >100 mg of Cu(II) per 50 g wet peat was necessary to exchange the maximum of bound metals (e.g. 21.8% of Al, 3.9% of Fe, 79.0% of Mn, 81.9% of Sr, related to their total content).     

Determination of Cu, Zn, Fe, Ni and Cd by flame atomic absorption spectrophotometry after preconcentration by Escherichia coli immobilized on sepiolite

A method for the determination of Cu, Zn, Fe, Ni and Cd by flame atomic absorption spectrophotometry (FAAS) after preconcentrating on a column containing Escherichia coli immobilized on sepiolite has been developed. Optimum pH values, amount of adsorbent, elution solution and flow rate have been obtained for the elements studied. The effect of interfering ions on the recovery of the analytes has also been investigated. Recoveries of Cu, Zn, Fe, Ni and Cd by E. coli immobilized on sepiolite were 99.1+/-0.6, 98.2+/-0.6, 98.1+/-0.5, 97.2+/-0.8 and 98.2+/-0.4% at 95% confidence level, respectively. The adsorption capacity of E. coli immobilized on sepiolite was found as 0.148, 0.064, 0.098, 0.134 and 0.088 mmol/g for Cu, Zn, Fe, Ni and Cd, respectively. The proposed method was applied to the determination of trace metals in alloys (NBS SRM 85b). Trace metals have been determined with relative error lower than 10%.     

Flame AAS/flame AES for trace determination in fresh and used lubricating oils with sample introduction by hydraulic high-pressure nebulization

In hydraulic high-pressure nebulization (HHPN) an aerosol is produced by means of an HPLC-pump and a special nebulization nozzle, applying a pressure of about 200 bar. This spray technique has been employed for sample introduction of mineral oil samples in flame atomic absorption/flame emission spectrometry. The determination of the trace elements Al, Cr, Cu, Fe, K, Na, Ni, Pb, Si and V has been investigated. Viscosity hardly acts upon the sensitivity of the determination, thereby avoiding a time consuming dilution of oil samples. By means of two interconnecting sampling valves a calibration method based on the standard addition technique can be performed which is both simple and easy to carry out. In samples of used oils, results for Cu and Pb equalled those of XRF-analysis. Regarding Fe traces, data obtained from AAS and XRF measurement correlate. In comparison with sample uptake by pneumatic nebulization, which is restricted to diluted oil samples, detection limits decrease by a factor of 2 to 4, indicating the dilution required in pneumatic nebulization.     

X-ray fluorescence determination of As, Bi, Co, Cu, Fe, Ni, Pb, Se, V and Zn in natural water and soil extracts after preconcentration of their pyrrolidinedithiocarbamates on cellulose filters

A simple method for the elements preconcentration on thin-layer paraffin-treated cellulose filters was proposed. It was found that pyrrolydinedithiocarbamates of As(III), Bi, Cd, Co, Cu, Fe(III), Ni, Pb, Se(IV), V(V) and Zn obtained after mixing of sample (3-5 ml min⁻¹) and reagent (0.7-1.0 ml min⁻¹) streams were quantitatively recovered from 100 ml sample. The sample acidity was adjusted to pH 4.8-5.2 for preconcentration of Cd, Co, Cu, Fe(III), Ni, Pb, V(V) and Zn, and to 2 M HCl for preconcentration of As, Bi and Se. The optimum reagent concentration was found to be 0.1%. The elements were determined on the filters by X-ray fluorescence spectrometry. The detection limits achieved were 0.1-4.0 μg of element on the filter. Relative standard deviation (R.S.D.) was not higher than 0.08 while determining 5-50 μg of elements on filter. Accuracy and precision of the technique proposed were evaluated by the analysis of spiked natural samples.     

X-射线荧光光谱法测定锌铝铜合金中的铝、铜、铁、硅、镍、铅和镉

建立了X射线荧光光谱法测定锌铝铜合金ZnAl6Cu1中铝、铜、铁、硅、镍、铅和镉的分析方法。探讨了各元素的分析条件,比较了不同制样方式及不同放置时间对铝强度的影响。在最佳的仪器分析条件下,测定了微量元素的检出限及主、次元素的精密度和准确度。检出限结果表明:各微量元素的检出限均满足标准要求,Cd和Pb元素的定量限稍高。精密度和准确度结果表明,铝、铜、铁元素的测量相对标准偏差在2.1%~5.9%,分析结果与国家标准方法一致。     

Spectrophotometric determination of traces of iron after extraction of Fe(II)-phenanthroline complex on polyurethane foam

A spectrophotometric method for the determination of traces of iron in glass and ceramic materials has been developed. The method involves formation of the Fe(II)-phenanthroline complex at pH 3-4 in aqueous medium, followed by its selective extraction and preconcentration on polyurethane foam from 2.5M perchloric acid and finally elution of the complex with acetone for spectrophotometric measurement at 510 nm. A wide linearity range from 0.05 to 3 mu g/ml Fe is obtained with the method. Co, Cu and Ni have no significant effect when they are present in the weight ratios Fe:Co < 1:2, Fe: Cu < 1:10 and Fe: Ni < 1:50. The method yielded satisfactory results when applied to various glass and ceramic samples.     

The determination of wear metals in used lubricating oils by flame atomic absorption spectrometry using sulphanilic acid as ashing agent

A simple and reliable ashing procedure is proposed for the preparation of used lubricating oil samples for the determination of calcium, magnesium, zinc, iron, chromium and nickel by flame atomic absorption spectrometry. Sulphanilic acid was added to oil samples and the mixture coked and the coke ashed at 550 degrees C. The solutions of the ash were analysed by flame AAS for the metals. The release of calcium, zinc, iron and chromium was improved by the addition of sulphanilic acid to samples. The relative standard deviations of metal concentration results in the initial oil samples were 1.5% for Ca (1500 mg l(-1) level), 0.3% for Mg (100 mg l(-1) level), 3.1% for Zn (1500 mg l(-1) level), 0.7% for Fe (500 mg l(-1) level), 0.02% for Cr (50 mg l(-1) level) and 0.002% for Ni (10 mg l(-1) level). The optimum sample size for efficient metal release was 20 g while the optimum sulphanilic acid to oil ratio was 0.05 g per gram of oil for Zn and Cr and 0.10 g for Ca and Fe. Results obtained by this procedure were highly reproducible and comparable with those obtained for the same samples using standard procedures.     

Cold ultrasonic acid extraction of copper, lead and zinc from soil samples

A cold ultrasonic acid method for extracting Pb, Cu and Zn from soil samples has been studied. This work focused on studying the experimental condition for extrating trace metals from soil samples at ambient temperature (≈25 °C) using Syrian soil samples; the same conditions were applied to reference soil samples(SL-1, Soil-7, SDM, and BCR-32). A short exposure time (4 h), and 2 ml of concentrated hydrochloric acid were found to be best. Under the applied conditions Pb, Cu and Zn were quantitavely extracted, while Sr, Mn, Fe, Al, Cr, Co, and Ni were partialy extracted. The advantages of the cold ultrasonic extraction method are as follows: it is selective, it is matrix free, the extraction time is short, the amounts of consumed chemicals are small, the by-products of the process are negligible and it is environmentally clean, since no fume emissions are emitted. The only disadvantage is that it is not a real total digestion method. Comparable results for the proposed ultrasound method and the hot-plate acid digestion method for Cu, Pb and Zn in certified refrence soil samples(SL-1, SDM, Soil-7, BCR-32, Soil-6) and some Syrian soil samples are obtained.     

Preparation and analytical characterization of a chelating resin coated with 1-(2-pyridylazo)-2-naphthol

A chelating sorbent was obtained by deposition of 1-(2-pyridylazo)-2-naphthol on Amberlite XAD-4. The analytical characteristics of the sorbent were established and optimum sorption conditions for Cu, Zn, Fe, Cd, Ni, and Pb under static and dynamic conditions were determined. The sorbent was applied to analysis of river water. After group separation of traces of metals on the sorbent and subsequent elution with hydrochloric add, the metals were determined in the effluent by atomic-absorption spectrophotometry.     

Dynamic ultrasound-assisted extraction of colistin from feeds with on-line pre-column derivatization and liquid chromatography-fluorimetric detection

A dynamic ultrasound-assisted extraction (UAE) method with on-line pre-column derivatization/high performance liquid chromatography (HPLC) and fluorimetric detection is proposed for the analysis of colistin in feed. A flow injection manifold is used for the development of the extraction and derivatization steps and for interfacing them with the separation/detection step, thus providing an on-line approach with the advantage of minimum sample handling. The derivatization was performed with ortho-phthaldialdehyde and 2-mercaptoethanol. The optimum conditions for colistin extraction and formation of the fluorescent derivative have been obtained by experimental design methodology. The use of a high-intensity probe sonication makes UAE an expeditious (7 min versus > 1 h) and efficient (93.1-98.2% versus 87.5-94% of recovery) alternative as compared with extraction using an ultrasonic bath. The within-laboratory reproducibility and repeatability, expressed as percentage of relative standard deviation, were 5.2 and 5.8, respectively.     

Amberlite XAD-7 impregnated with Xylenol Orange: a chelating collector for preconcentration of Cd(II), Co(II), Cu(II), Ni(II), Zn(II) and Fe(III) ions prior to their determination by flame AAS

A new chelating resin, Xylenol Orange coated Amberlite XAD-7, was prepared and used for preconcentration of Cd(II), Co(II), Cu(II), Fe(III), Ni(II) and Zn(II) prior to their determination by flame atomic absorption spectrophotometry. The optimum pH values for quantitative sorption of Cd(II), Co(II), Cu(II), Fe(III), Ni(II) and Zn(II) are 4.5-5.0, 4.5, 4.0-5.0, 4.0, 5.0 and 5.0-7.0, respectively, and their desorptions by 2 mol L(-1) HCl are instantaneous. The sorption capacity of the resin has been found to be 2.0, 2.6, 1.6, 1.6, 2.6 and 1.8 mg g(-1) of resin for Cd, Co, Cu, Fe, Ni and Zn, respectively. The tolerance limits of electrolytes, NaCl, NaF, NaI, NaNO3, Na2SO4 and of cations, Mg2+ and Ca2+ in the sorption of the six metal ions are reported. The preconcentration factor was between 50 and 200. The t1/2 values for sorption are found to be 5.3, 2.9, 3.2, 3.3, 2.5 and 2.6 min for the six metals, respectively. The recoveries are between 96.0 and 100.0% for the different metals at preconcentration limits between 10 to 40 ng mL(-1). The preconcentration method has been applied to determine the six metal ions in river water samples after destroying the organic matter (if present in very large amount) with concentrated nitric acid (RSD < or = 8%, except for Cd for which it is upto 12.6%) and cobalt content of vitamin tablets with RSD of approximately 3.0%.