Flame AAS/flame AES for trace determination in fresh and used lubricating oils with sample introduction by hydraulic high-pressure nebulization

In hydraulic high-pressure nebulization (HHPN) an aerosol is produced by means of an HPLC-pump and a special nebulization nozzle, applying a pressure of about 200 bar. This spray technique has been employed for sample introduction of mineral oil samples in flame atomic absorption/flame emission spectrometry. The determination of the trace elements Al, Cr, Cu, Fe, K, Na, Ni, Pb, Si and V has been investigated. Viscosity hardly acts upon the sensitivity of the determination, thereby avoiding a time consuming dilution of oil samples. By means of two interconnecting sampling valves a calibration method based on the standard addition technique can be performed which is both simple and easy to carry out. In samples of used oils, results for Cu and Pb equalled those of XRF-analysis. Regarding Fe traces, data obtained from AAS and XRF measurement correlate. In comparison with sample uptake by pneumatic nebulization, which is restricted to diluted oil samples, detection limits decrease by a factor of 2 to 4, indicating the dilution required in pneumatic nebulization.     

Atomic absorption determination of Cd, Co, Cu, Fe, Ni in viscous aqueous solutions of poly(ethyleneimine) using a high-pressure flow and nebulization system for sample introduction

Summary The influence of increasing concentration of water-soluble polymers on the analytical signals for Cd, Co, Cu, Fe, Ni in flame atomic absorption spectrometry with hydraulic high-pressure nebulization (HHPN) and pneumatic nebulization (self uptake mode) has been studied using aqueous solutions of poly(ethyleneimine) (PEI) as examples. For a solution of 50 g/l polymer, HHPN sample introduction leads to a 5.0 (Cd), 8.8 (Co), 17 (Cu), 7.1 (Fe) and 22 (Ni) fold higher sensitivity compared to pneumatic nebulization. Even at polymer concentrations of more than 100 g/l HHPN operation is still possible without any problems, whilst such viscous solutions cannot be transferred into an aerosol by a pneumatic nebulizer.     

A multicommuted flow system for the determination of copper, chromium, iron and lead in lubricating oils with detection by flame AAS

In this work, a flow analysis procedure for the determination of copper, chromium, iron and lead in lubricating oils using flame AAS as detection technique is described. The flow manifold was designed to implement the multicommutation approach and it comprised three 3-way solenoid valves controlled by a personal computer. The flow system presented allowed to process the oil samples to determine wear metals without any prior preparation. Aiming to assess accuracy the results were compared with those obtained by manual procedure using flame AAS. Applying the joint-confidence ellipse test, no significant difference at the 95% confidence level was observed. Other profitable features such as a sample throughput of 50 determinations per hour; relative standard deviations (n = 5) below 2% for Cu, and below 8% for Cr, Fe and Pb; and linear responses in the range 0–40 ppm (w/w) (Cu, Fe) and 0–15 ppm (w/w) (Cr, Pb) were also achieved.     

Reduction of matrix interferences and improvement of detection power in flame AAS by a high-performance flow/hydraulic high-pressure nebulization system for sample introduction (HPF/HHPN)

Summary For analysis of highly concentrated salt solutions, the samples are injected into a high-performance carrier stream and transported to a special high-pressure nebulization nozzle (max. pressure: 400 bar/40 MPa). An aerosol of very small droplets is formed only by the high fluid pressure without using nebulization gas. The nozzle replaces the pneumatic nebulizer (high-performance flow/hydraulic high-pressure nebulization system: HPF/HHPN). In comparison with pneumatic nebulization, matrix interferences are significantly reduced and sensitivity is improved by factors of 2 to 8 (depending on the element and matrix to be analyzed). For the determination of 10 elements in the matrices Al (30 g/l), Fe (150 g/l) and Cu (330 g/l), the element-specific improvement of the detection power by a factor of 4.1 to 9.7 for Al, 1.3 to 4.9 for Fe and 1.3 to 10 for Cu is achieved.     

Determination of Wear Metals in Marine Lubricating Oils by Microwave Digestion and Atomic Absorption Spectrometry

 The difficulties associated with the development of a microwave-assisted acid digestion of lubricating oils in determination of wear metals are presented. The interest of this sample treatment lies in its basis for determining the total metal contents with enough sensitivity by flame atomic absorption spectrometry (FAAS). It allows earlier diagnosis of the engine state than is obtained by the widely applied simple dilution procedure. Another advantage is the avoidance of contamination and loss of the metals to be determined. The procedure employs nitric acid and hydrogen peroxide in a four-stage programme. Fe, Cu, Cr and Pb are determined by FAAS as representative of engine wear. The limits of detection are 0.1 μg/g for Fe and Cr and 0.05 μg/g for Cu and Pb. A comparison with other procedures is presented for spiked samples. Different types of used lubricating oils supplied by an oil company were analysed to prove the suitability of the procedure proposed. Received November 11, 1998. Revision Februray 20, 1999.     

Development of multi-elemental method for quality control of parenteral component solutions using ICP-MS

An inductively coupled plasma mass spectrometry (ICP-MS) method for elemental impurities determination in components used for parenteral nutrition solutions is proposed. Solutions of amino acids (10% m/v), glucose (50% m/v) and lipids (20% m/v) were analyzed. Arsenic, Cd, Cu, Pb and Mo were determined by ICP-MS operated at standard mode, whilst pneumatic nebulization was used for introducing the sample solution into the ICP. Mercury was determined using cold vapor generation (CVG) coupled to ICP-MS. Chromium, Mn, Ni and V were determined by means of dynamic reaction cell-inductively coupled plasma mass spectrometry (DRC-ICP-MS), while ammonia was used as reaction gas. The operational conditions of each technique were optimized in order to achieve better sensitivity, precision and accuracy. The influence of the sample matrix, mainly carbon, on all investigated elements was evaluated. The use of DRC was effective to reduce interferences on Cr, Mn, Ni and V determination. The other investigated elements (As, Cd, Cu, Pb, Mo and Hg) were determined directly in the samples, which were properly diluted. Results obtained were in good agreement (between 96 and 103%) with certified values (certified reference materials of water were analyzed), at the same time as the relative standard deviation was lower than 5%. Sample throughput was relatively high (up to 30 samples of components used for parenteral nutrition solution could be analyzed per hour). In this way, the proposed method can be recommended for routine analysis.     

Inductively coupled plasma optical emission spectrometric determination of trace elements in sediments after sequential selective extraction: effects of reagents and major elements on the analytical signal

The interfering effects due to the reagents and matrix elements associated with a four step sequential extraction procedure on ICPOES determination of trace elements were investigated in a systematic way. The emission lines were selected in order to include the most interesting elements for environmental studies (Zn, Pb, Ni, Cr, V and Cu) and the concentrations ranged according with the values occurring in the real samples. In order to distinguish between chemical and physical interfering effects, the Mg 280.270–Mg 285.213 line intensity ratio was measured, in each condition. Both pneumatic and ultrasonic nebulization were considered for comparison. It was found that both the elements which constitute the sample and the reagents which are added during the sample preparation steps significantly influence the emission intensity of all the analytes, depending on the analytical concentration and the nebulization system. Generally, the signal variations were higher with ultrasonic nebulization. Concerning the interference mechanism, it was found that the effect of the major elements (Na, K, Mg, Ca, Al and Fe) is essentially related to a change of the aerosol generation and transport processes. Differently, acetic acid, ammonium acetate and hydroxylamine hydrochloride significantly improved the plasma excitation conditions, depending on their concentration. A change of the sample introduction efficiency due to the presence of these reagents was also evident. On the contrary, the effect of hydrochloric and nitric acid emerged to be related only to the processes occurring in the sample introduction system.     

微波灰化-电感耦合等离子体原子发射光谱法测定原油中的金属元素

采用微波灰化技术消化原油样品,并使用电感耦合等离子体原子发射光谱法(ICP-AES)测定其中Na、Mg、Ca、Fe、V、Ni和Cu的含量。探讨了原油样品中金属元素测定的称样量和微波灰化程序,并优化了仪器工作参数和实验条件。样品经微波灰化处理后,用盐酸溶解残渣,方法对Na、Mg、Ca、Fe、V、Ni和Cu元素的检出限分别为0.07、0.01、0.01、0.01、0.02、0.04和0.03mg/kg,回收率在84.5%～96.6%之间,相对标准偏差在2.1%～6.9%范围。方法简便、可靠,可用于原油中Na、Mg、Ca、Fe、V、Ni和Cu 7种金属元素的检测。     

Determination of wear metals in lubricating oils by flame atomic absorption spectrophotometry

A simple, rapid and reliable method was developed for the determination of copper, nickel, iron and lead in fresh and used lubricating oil samples by flame atomic absorption spectrophotometry (FAAS). In the present study, a mixture of organic solvents containing propionic acid and iso-butylmethyl ketone (1: 1) was used to extract the metals from lubricating oil samples followed by FAAS analysis. Aqueous standard solutions can be easily employed with the proposed mixed solvent system instead of organometallic standards. The analytical results obtained by employing the proposed solvent extraction system were found to be in good agreement with the results for aqueous media obtained after the destruction of oil samples matrix. Percentage recovery studies showed 88–98% for Cu, 92–95% for Fe, 96–106% for Ni and 84–100% for Pb with relative standard deviation of 2–6%. The developed method was effectively applied to routine determination of Cu, Ni, Fe, and Pb in lubricating oil samples.     

Determination of metal content in valerian root phytopharmaceutical derivatives by atomic spectrometry

Phytopharmaceuticals containing Valerian are used as mild sleep-inducing agents. The elemental composition of 3 different marks of Valeriana officinalis roots commercially available in the Argentinian market, their teas, and a commercial tincture have been studied. The content of Al, Ca, Cd, Co, Cr, Cu, Fe, Li, Mn, Ni, Pb, V, and Zn was determined in phytopharmaceuticals by flame atomic emission/absorption spectrometry, electrothermal atomic absorption spectrometry, and ultrasonic nebulization coupled to inductively coupled plasma-optical emission spectrometry. Prior to analyses of the samples, a digestion procedure was optimized. The analytical results obtained for Fe, Al, Ca, and V in the solid sample study were within the range 100-1000 mg/kg, and for Mn, Zn, and Pb within the range 10-100 mg/kg. Cadmium was found at levels up to 0.0125 mg/kg.     

Coupling of ultrasonic nebulization to flame furnace atomic absorption spectrometry—new possibilities for trace element determination

The use of ultrasonic nebulization (USN) with desolvation system for sample introduction in flame atomic absorption spectrometry (F AAS) and flame furnace atomic absorption spectrometry (FF AAS) with a nickel tube is described. Polytetrafluorethylene (PTFE) adaptors were built to replace the pneumatic nebulizer for USN-F AAS measurements. For USN-FF AAS analysis, an alumina injector allowed the direct introduction of the dry aerosol into the nickel tube. The analytical performance of both systems is shown for Ag, Bi, Cd, Cr, Cu, Mn, Pb, Sb, Se, Tl and Zn. The results demonstrate that a sensitivity gain of up to 39 times can be achieved using USN-FF AAS, mainly due to the increase in residence time and to the absence of dilution of the analyte by the flame gases, as the atomization takes place inside the nickel tube. However, elements that require higher atomization temperatures, such as Cr and Mn, are more efficiently determined using USN-F AAS. To evaluate the accuracy of the proposed methods for the determination of trace elements, five certified reference samples were analyzed, and good agreement was, in general, achieved between certified and determined values at a 95% confidence level. The relative standard deviation was frequently below 5%, demonstrating good precision, particularly for USN-FF AAS. In this sense, coupling of USN with F AAS and especially with FF AAS has proved to be simple, safe, with high precision and good accuracy, also maintaining some of the most important features of F AAS, such as the high analytical frequency and the low running cost.     

Rapid Procedure to Determine Wear Metals in Lubricating Oils and the Analysis of Variance in the Evaluation of Sample Preparation Procedures

 A new sample treatment is proposed based on a partial wet digestion in closed reactors assisted by microwaves for wear metal determinations by flame atomic absorption spectrometry (FAAS). It is rapid, precise and sensitive and allows the use of inorganic standards. Problems concerning solubility have been overcome with mixed solvents. The repeatability, stability, calibration curve and limit of detection were established. Six samples, with different degree of wear were analyzed for Fe, Cu, Pb and Cr by FAAS using the procedure proposed and other sample treatment procedures from the literature. Pb and Cr were not found in all samples. The one-way analysis of variance for Fe applied to each sample confirms the need of an acid attack and the importance of HCl for the digestion. The results obtained for Cu led us to use a two-way analysis of variance for all the samples considering the preparation procedures and the samples as variation sources. It showed no significant differences for the preparation procedures used. Therefore, treatments implying the use of acids are recommended when several wear metals are analyzed. On the other hand, the differences between the simple dilution and the procedures, implying the dissolution of metallic particles is an index to predict an imminent engine failure. Received March 1, 2001. Revision July 10, 2001.     

Electrothermal vaporization in inductively coupled plasma atomic emission spectrometry for direct multielement analysis of food samples with slurry sampling

Slurry sampling followed by electrothermal vaporization (ETV) was used as sample introduction technique in inductively coupled plasma atomic emission spectrometry (ICP-AES) for the direct determination of trace elements in food samples. A polytetrafluoroethylene (PTFE) emulsion was used as a fluorinating reagent to promote vaporization and the transportation of analytes. The main factors affecting the analytical signals were investigated in detail. Under optimum operating conditions, the detection limits (DL) for this method varied from 1.8 (Cu) to 215 ng/mL (Zn), while the relative standard deviations (RSD) were in the range 2.6% (Cu)-7.2% (Zn). The proposed method was successfully applied to the direct determination of trace amounts of V, Cu, Cr, Fe, Zn, and La in rice without any chemical pretreatment. The precision was evaluated by analyzing a standard reference material (tea leaves, GBW 07605) and comparing the results from this method with results obtained by pneumatic nebulization (PN) ICP-AES after the wet-chemical decomposition of the same sample.From Zhurnal Analiticheskoi Khimii, Vol. 60, No. 3, 2005, pp. 286–290.Original English Text Copyright © 2005 by Chen.This article was submitted by the author in English.     

The use of electrothermal vaporization ICP-OES for the determination of trace elements in human hair using slurry sampling and PTFE as modifier

A procedure for the determination of trace elements in human hair has been proposed by electrothermal vaporization inductively coupled plasma optical emission spectrometry (ETV-ICP-OES) with slurry sampling. Slurry was prepared by immersing human hair with conc. HNO₃ and then adding a polytetrafluoroethylene (PTFE) slurry, which was used as a chemical modifier for the improvement of vaporization characteristic of analyte. The slurry was homogenized with an ultrasonic vibrator before the measurement. The vaporization behaviour of the analytes in slurry and solution and the main influence factors for the determination were studied with the addition of PTFE systematically. Detection limits for this method varied from 0.033?µg?g^?1 (Cu) to 3.21?µg?g^?1 (Zn) with the relative standard deviations (RSDs) of 2.8–7.1%. The proposed method was successfully applied for the determination of trace elements (Cu, Mn, Cr, Fe, Zn, Cd and Pb) in human hair with minimum chemical pretreatment and aqueous calibration. The accuracy was checked by comparing the results of this method with those using pneumatic nebulization (PN) ICP-OES after a conventional acid decomposition of the same sample. In addition, the standard reference material of human hair (GBW 07601) was analysed with good agreement between the results from the proposed method and the certified values.     

Different Lubricating Oil Treatments for the Determination of Cu,Cr, Fe,Ni, Sb,Pb, and Zn by HR-CS FAAS

Abstract

Microwave-assisted acid decomposition, direct dilution in kerosene, and oil-in-water emulsion were evaluated as lubricating oil pretreatment procedures for Cu, Cr, Fe, Ni, Pb, Sb, and Zn determination by High-Resolution Continuum Source Flame Atomic Absorption Spectrometry (HR-CS FAAS). For wet digestion, results were compared with those obtained by Flame Atomic Absorption Spectrometry (FAAS). The ultrasound probe used in emulsions sonication contaminated samples with Cr, although better results have been observed for the other six elements in this condition. In general, recovery percentages ranging from 81–106% (Cu), 80–107% (Cr), 85–114% (Fe), 82–116% (Ni), 86–117% (Pb), 85–115% (Sb), and 81–114% (Zn) were obtained. The HR-CS FAAS showed to be faster and more sensitive than FAAS.     

Use of a capacitively coupled microwave plasma (CMP) with Ar, N2 and air as working gases for atomic spectrometric elemental determinations in aqueous solutions and oils

A comparative study was performed of 600 W capacitively coupled microwave plasmas (CMP) with different plasma gases (Ar, N₂ and air) and aerosol generation with the aid of a Légère pneumatic nebulizer. Detection limits with the different working gases are in the order of 15–4000 ng/mL for Fe, Cr, Zn, Mg and Ca in aqueous solutions. The influence of organic solutions on the stability of the plasma is discussed. The determination of Co, Cr, Fe, Mg and Ni in different oil samples by OES is described, using an air-CMP and pneumatic nebulization after dilution of the oils by 20% with cyclohexane. The detection limits for these elements are in the 100–400 ng/g range. Results obtained for a waste motor oil for the elements mentioned in the concentration range of 4–50 μg/g were found to be in good agreement with those obtained by ICP-OES after digestion of the oils at high pressure in PTFE vessels. Received: 10 March 1997 / Revised: 23 May 1997 / Accepted: 30 May 1997     

Use of a capacitively coupled microwave plasma (CMP) with Ar, N2 and air as working gases for atomic spectrometric elemental determinations in aqueous solutions and oils

A comparative study was performed of 600 W capacitively coupled microwave plasmas (CMP) with different plasma gases (Ar, N₂ and air) and aerosol generation with the aid of a Légère pneumatic nebulizer. Detection limits with the different working gases are in the order of 15–4000 ng/mL for Fe, Cr, Zn, Mg and Ca in aqueous solutions. The influence of organic solutions on the stability of the plasma is discussed. The determination of Co, Cr, Fe, Mg and Ni in different oil samples by OES is described, using an air-CMP and pneumatic nebulization after dilution of the oils by 20% with cyclohexane. The detection limits for these elements are in the 100–400 ng/g range. Results obtained for a waste motor oil for the elements mentioned in the concentration range of 4–50 μg/g were found to be in good agreement with those obtained by ICP-OES after digestion of the oils at high pressure in PTFE vessels. Received: 10 March 1997 / Revised: 23 May 1997 / Accepted: 30 May 1997     

Cloud point preconcentration and flame atomic absorption spectrometric determination of Cd and Pb in human hair

Cloud point methodology has been successfully used for the preconcentration of trace amounts of Cd and Pb as a prior step to their determination by flame atomic absorption spectrometry. O,O-Diethyldithiophosphate and Triton X-114 are used as hydrophobic ligand and non-ionic surfactant, respectively. After phase separation at 40 °C based on cloud point of the mixture, the surfactant-rich phase is diluted with methanol. The enriched analyte in the final solution is determined by flame atomic absorption spectrometry using conventional nebulization. After optimization of the complexation and extraction conditions, enhancement factors of 22 and 43 were obtained for Cd and Pb, respectively. Under the experimental conditions used, preconcentration of only 10 ml of sample in the presence of 0.05% (v/v) Triton X-114 permitted the detection of 0.62 μg l⁻¹ of Cd and 2.86 μg l⁻¹of Pb. The proposed method was applied to the determination of Cd and Pb in human hair samples.     

Preconcentration of trace elements by partial dissolution of the matrix—multielement preconcentration from manganese

Trace elements such as Ag, Au, Bi, Cd, Co, Cu, Fe, Ga, In, Ni, Pb, Pd and Tl, can be preconcentrated with recoveries of better than 95% from high-purity manganese if the sample is coated with a thin layer of mercury before its dissolution in HCl to a small residue. For determination of the trace elements, the residue is completely dissolved in aqua regia. After separation of the mercury by reductive precipitation, Bi, Cd, Co, Cu, Fe, Ga, In, Ni, Pb, and Tl are determined by flame a.a.s. ('injection method'). Ag, Au and Pd are determined in the mercury-containing solution. The relative standard deviation was usually about 5%; Cu, Fe and Pb were proved to be inhomogeneously distributed in the sample (electrolytically produced manganese), and so the standard deviations were considerably greater. The detection limits for the different elements were between 0.6 and 0.004 ppm, depending on the sensitivity of their a.a.s. determination. The theoretical basis of this preconcentration method and its applicability to multielement analysis of different high-purity metals are discussed.     

Analysis of undigested honey samples by isotope dilution inductively coupled plasma mass spectrometry with direct injection nebulization (ID-ICP-MS)

Undigested honey samples were analyzed by inductively coupled plasma mass spectrometry (ICP-MS) using direct injection nebulization (DIN). Samples were diluted 25-fold using dilute HNO₃ to which Triton X-100 was added. Isotope dilution (ID) was used to quantify Ba, Cu, Pb and Zn in these natural matrix samples. DIN parameters were optimized to obtain a stable transient signal enough to determine multiple isotope ratios. The Ba, Cu and Zn isotope ratios were measured in a single sample injection of 50 μl diluted honey and the Pb isotopes in a separate injection. The analysis was characterized by precisions given by R.S.D. values from 0.20 to 1.24% for Ba, 0.49–1.23% for Cu, 0.61–2.28% for Pb and 0.50–1.51% for Zn. The results were in agreement, at the 95% confidence level, with those obtained by analyzing digested samples using external calibration. Using this direct method, 30 real honey samples per hour could be analyzed.