碳布生长二维Ni-Mn MOF用于柔性超级电容器

通过溶剂热法在碳布（CC）表面生成二维Ni-Mn层状双金属氢氧化物,利用溶剂热法将其转化为二维Ni-Mn金属有机骨架（Ni-Mn MOF）,产物形貌保持良好。探究了不同Ni、Mn元素物质的量之比、反应温度和反应时间对材料形貌、结构及性能的影响。当Ni、Mn元素物质的量之比为9：1、反应温度为120 ℃、反应时间为12 h时,Ni-Mn MOF/CC电极的电化学性能最佳。在电流密度为1 mA·cm^-2时,该电极的面积比电容高达4 007.5 mF·cm^-2,同时该电极具有良好的循环稳定性。将该电极应用于柔性对称超级电容器中,该柔性对称超级电容器可180°弯折,且在10 mA·cm^-2的电流密度下进行5 000次循环后电容保留率为83.6%,具有良好的循环稳定性和柔韧性。     

Zn掺杂Co9S8纳米材料的制备及其在超级电容器和电催化析氢中的应用

采用原位溶剂热生长法设计合成了锌掺杂Co₉S₈纳米颗粒。各种表征技术和性能测试结果表明：锌掺杂Co₉S₈纳米颗粒的孔尺寸为18 nm,比表面积为23 m²·g^-1;同时微量的锌掺杂显著增强了Co₉S₈的电催化析氢（HER）活性及电容器性能。在HER性能测试中,当电流密度为10 mA·cm^-2时电位为-361 mV,电流密度最高可达38.26 mA·cm^-2,且具有优异的循环稳定性。同时在电容器性能测试中具有较高的比电容,当电流密度为1 A·g^-1时,质量比电容和面积比电容分别为235.48 F·g^-1和812.4 mF·cm^-2。     

一种高容量的层状Co-MOF基超级电容器电极材料

通过简单的溶剂热反应合成了一种钴基层状MOF（[Co（4,4''-bpy）（tfbdc）（H₂O）₂],Co-BTH,4,4''-bpy=4,4''-联吡啶,H₂tfbdc=四氟对苯二甲酸）,并考察了其作为超级电容器电极材料的性能。研究结果表明：Co-BTH电极具有良好的赝电容性能,包含高比电容和较好的倍率性能。在1 A·g^-1电流密度下和1 mol·L^-1 KOH溶液中,其比电容最大可达2 316 F·g^-1。在2 A·g^-1的电流密度下,循环1 000次后,电极的比电容仍然还有847 F·g^-1。良好的赝电容性能与Co-BTH的层状结构和小尺寸的纳米片有关。     

空心六边形镍钴硫化物/RGO复合物的合成及其超级电容性能

通过两步法制备了一种空心六边形镍钴硫化物（HHNCS）与还原氧化石墨烯（RGO）的纳米复合材料HHNCS/RGO。利用XRD,SEM,TEM和Raman光谱等对复合物进行表征,发现镍钴硫化物为空心六边形结构,并且均匀地附着在RGO的表面。该纳米复合物用作超级电容器电极表现出优异的电化学性能。在电流密度为1 A·g^-1时比电容为927 F·g^-1;当电流密度增大到20 A·g^-1时,比电容仍高达724 F·g^-1,表明材料拥有较好的倍率性能。此外,在电流密度5 A·g^-1下循环2000次后比电容保留有初始值的93%,显示出优异的循环稳定性。HHNCS/RGO优异的电容性能主要是由于RGO的存在不仅增强了材料的导电性,而且作为理想的载体分散HHNCS纳米片。HHNCS/RGO纳米复合物优异的电化学性能使其在超级电容器电极材料领域具有应用前景。     

表面官能团化增强碳纳米笼超级电容器性能

以具有多级孔结构、高比表面积、良好导电性等特征的碳纳米笼（CNCs）为前体,采用硝酸氧化法在CNCs表面引入含氧官能团。以CNCs为超级电容器电极材料,在相同电流密度下,官能团化样品的比电容显著高于纯CNCs;在1A·g^-1下比电容最高可达到255F·g^-1,比纯CNCs的188F·g^-1增加了34%,这表明表面含氧官能团化能够显著提高CNCs的超级电容器比电容。在100A·g^-1的大电流密度下,硝酸氧化后CNCs的比电容保持在111~167F·g^-1,表明具有良好的耐大电流充放电性能。在10A·g^-1的电流密度下循环10000圈后,CNC-6M样品的比电容由196F·g^-1下降到176F·g^-1,样品的比电容仍保留90%,具有良好的循环稳定性。表面含氧官能团化CNCs所表现出的这种优异的超级电容器性能归因于CNCs的多尺度分级孔结构、高比表面积、良好的导电性、表面亲水性含氧官能团化带来的浸润性提高和引入的赝电容。     

琥珀酸构建具有超级电容器性能的混合金属有机骨架

采用简单的溶剂热法合成了混合金属有机骨架材料（MOF （Ni,Co））,然后通过X射线衍射、FT-IR、扫描电子显微镜、X射线光电子能谱和N₂吸附-脱附对制备的材料进行了表征,并进一步研究了其作为超级电容器电极材料的性能。结果表明,具有独特的纳米花状结构的MOF （Ni_1.2Co_0.8）可以提供更多的电活性位点,从而具有优异的电化学性能,在1 A·g^-1时的比电容为850 F·g^-1。同时本研究工作说明MOF （Ni）电极材料在掺杂适量钴元素后,可增强电极内部电子/离子转移,降低活性物质和电解液之间的接触电阻,提高导电性,增强电化学性能。     

CoFeOx/MoO2准平行纳米阵列电极的析氢性能

利用CoFe层状双金属氢氧化物(CoFe LDH)准平行纳米片阵列作为载体前驱体,通过原位负载及煅烧方式,实现了含有氧空位的 MoO₂纳米颗粒在纳米片阵列表面的生长。电化学研究结果表明,所得 CoFeO_x/MoO₂纳米阵列电极具有高析氢反应(HER)催化活性。该电极在10和1 000 mA·cm^-2时的HER过电位分别为40和217 mV。在50 mA·cm^-2的电流密度下,该电极可以稳定运行125 h。     

NiFe水滑石纳米片阵列负载Ru用于提升碱性电催化析氢和析氧性能

通过离子交换的方式将Ru负载到NiFe水滑石（LDH）纳米阵列表面得到（Ru/NiFe LDH），Ru的引入显著提升了NiFe LDH的活性比表面积，暴露了更多的活性位点，同时调控了其电子结构，大大提升了其本征催化活性。在碱性条件下，催化析氢反应时仅需50 mV的过电位即可达到10 mA·cm^-2的电流密度，Tafel斜率为52.3 mV·dec^-1。而相同条件下原始NiFe LDH达到10mA·cm^-2的电流密度则需要226 mV的过电位，Tafel斜率为157.5 mV·dec^-1。同时制备的Ru/NiFe LDH也展现出了良好的析氧催化活性，在50 mA·cm^-2的电流密度下，过电位仅为231 mV，而NiFe LDH则需237 mV。Ru/NiFe LDH在长时间的电催化条件下依然能保持良好的工作稳定性。     

空心海胆状二氧化锰的制备及其在超级电容器中的应用

采用简单的一步水热法制备了空心海胆状二氧化锰,无需任何模板剂和表面活性剂。该材料具有3D的纳米结构,结构稳定,并由单个的二氧化锰空心管自组装而成。该纳米材料的特殊结构为其提供了高的比电容。在1mol·L^-1硫酸钠电解液中,扫速为1mV·s^-1的条件下,该材料的比电容值为254.6F·g^-1。在电流密度为1.0A·g^-1的条件下,充放电循环1000次后比电容值仍保持为初始值的97.5%。表明该材料具有良好的电容性能和稳定性,其具备用作高性能超级电容器的电极材料的潜能。     

泡沫镍负载NiMoO4/NiMoS4复合材料的制备及其电化学性能

以泡沫镍作为基底，采用水热法原位生长出具有片状结构的NiMoO₄活性材料，然后通过水热硫化制备出NiMoO₄/NiMoS₄复合材料，研究了水热时间和硫脲添加量对样品形貌和电化学性能的影响。电化学结果表明，NiMoO₄/NiMoS₄电极在电流密度为 1 A·g^-1时，比电容为 1 560.7 F·g^-1，在电流密度为 40 A·g^-1时循环 2 000次后，比电容仍为初始比电容的 76.7%。将 NiMoO₄/NiMoS₄电极材料与活性炭(AC)分别作为正、负极组装的非对称超级电容器(ASC)在 400 W·kg^-1的功率密度下可提供 29.0 Wh·kg^-1的能量密度。     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

正丁胺对激光染料荧光谱影响的研究

用正丁胺作为碳源,采用射频辉光放电制备碳膜,选用激光染料R6G和聚乙二醇混合液作为蒸气源,采用单源热蒸发,在蒸发室与染料同时沉积得到混合膜,用拉曼光谱和红外光谱分析了碳膜的结构和键合方式,分析表明:碳膜中存在胺基团和氢原子.混合膜的荧光谱测量结果表明,认为正丁胺对染料荧光谱的影响是因为胺基和氢原子的存在.     

Cu0-catalysed 1,3-dipolar cycloadditions of α-amino acid derived N,N-cyclic azomethine imines to ynones

A series of 20 CuAIAC reactions between eight 4-acylamino substituted pyrazolidine-3-one-1-azomethine imines and four terminal ynones were performed using Cu⁰ as catalyst. The corresponding fluorescent cycloadducts were obtained in very high yields upon simple workup. Thus, Cu-metal turned out to be a better catalyst than Cu^I in terms of yield and ease of isolation. Availability of azomethine imines, mild reaction conditions, and simple workup enable a “click” access to libraries of densely substituted 2,3-dihydro-1H,5H-pyrazolo[1,2-a]pyrazol-1-ones. Reactivity of differently substituted dipoles was evaluated experimentally and by quantum chemical methods (DFT).     

Synthesis and antioxidative/anti-inflammatory activity of novel fullerene–polyamine conjugates

(E)-4-(Fullerenopyrrolidin-1-yl)-3-methylbut-2-enoic acid and its corresponding succinimidyl ester, readily obtained through Prato-type modification of C₆₀, were used for the selective N-acylation of polyamines. The thus obtained conjugates were evaluated for their antioxidative and anti-inflammatory activity and their cytotoxicity was determined. Members of this family of compounds showed interesting anti-lipid peroxidation, anti-lipoxygenase and anti-inflammatory activity and comparable cytocompatibility to spermidine.