尖晶石Li4Ti5O12中锂离子的化学扩散系数的研究

A relatively simple galvanostatic method was used for the evaluation on the average chemical diffusion coefficient of lithium-ion in spinel Li₄Ti₅O₁₂ prepared by solid-state reaction technique. The diffusion coefficient of lithium-ion was estimated to be 2.8×10^-13 cm²·s^-1 and 1.3×10^-13 cm²·s^-1 for charge and discharge， respectively.     

LiV3O8的合成及其电化学性能研究

The layered trivanadate, LiV₃O₈, was prepared by sol-gel method with LiOH, V₂O₅ and H₂O₂ as initial reagents. The materials at different heat treatment conditions were characterized by XRD and TG-DTA. Their electrochemical behaviors were studied by galvanostatic charge-discharge and cyclic voltammetry. The results show that LiV₃O₈ prepared by sintering at 300 ℃ for 16 h has higher capacity, and its initial discharge capacity is 333.1 mAh·g^-1, and maintains a discharge capacity of 302.8 mAh·g^-1 after 10 cycles at 0.2 C and the voltage range of 1.8～4.0 V.     

新型阴极材料Ba0.5Sr0.5Co0.8Fe0.2O3-σ制备与性能研究

Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3-σ(BSCF), a new cathode material for solid oxide fuel cell (SOFC), was synthesized by polyacrylicacid (PAA) method. The lattice structures of samples calcined at different temperatures were characte-rized by XRD. Shrinkage, porosity and pore size of the porous BSCF as a function of sintering temperature were investigated. It was found that the cubic perovskite structure could be formed after calcination at 800 ℃ for 2 h, but not well crystallized as seen from some unknown phases, and the pure cubic perovskite structure was formed after calcination at 1 150 ℃ for 2 h. The particle size of BSCF was less than 1～2 μm. The shrinkage of the porous BSCF increased with sintering temperature, but the opposite was true for the porosity. After sintering at 1 100 ℃ for 4 h, the porous BSCF was still in an appropriate structure, with porosity of 29% and electrical conductivity above 400 S·cm^-1.     

柠檬酸溶胶凝胶法制备LiCoO2电极材料及其表征

LiCoO₂ precursors of the cathode material for lithium-ion batteries were prepared from lithium hydroxide， basic cobalt carbonate and citric acid by a sol-gel method. The LiCoO₂ samples were obtained by sintering the gel pre-cursors at different temperatures and for different times. The thermal decomposition behavior of the gel precursors was examined by means of thermo-gravimetric analysis and differential thermal analysis using a PCT-IA thermal analyzer system. Their structures and morphologies were characterized by powder XRD and SEM techniques. It was found that using citric acid realized that the formation of LiCoO₂ crystal can be clearly differentiated to the nucle-ation and growth processes of the crystals; furthermore， the crystal size can be controlled. Electrochemical tests using the LAND BT1-10 test system showed the electrochemical performance of the material is affected by its in-tegrity and stability.     

碳包覆LiFePO4的一步固相法制备及高温电化学性能

Carbon coated LiFePO₄ cathode material was synthesized by one-step solid-state reaction and characterized by X-ray diffraction (XRD), field-emission-scanning electron microscope (FESEM). Electrochemical performances of the material as cathode in lithium-ion battery were investigated at medium and elevated temperature (30 and 55 ℃) by galvanostatic charge-discharge and A.C. impedance tests. The results show that carbon coated LiFePO₄ powder exhibits a well-crystallized olivine structure and spherical morphology with an average particle size of about 500 nm. Galvanostatic charge-discharge tests show that the reversible discharge capacity at 1 C and 1.5 C rates was improved from 121 and 105 mAh·g^-1 at 30 ℃ to 136 and 123 mAh·g^-1 at 55℃, respectively, while the enhancement of high temperature on electrochemical performance is less obvious at a rate lower than 0.5 C. Impedance spectra analyses indicate that the cathode material has a remarkably higher lithium-ion diffusivity at 55 ℃ than that at 30 ℃, which improves the electrochemical performance at high temperature.     

储氧材料制备过程中的结构及织构变化

Ce_0.65Zr_0.35O₂ solid solution was prepared by co-precipitation method and characterized by X-ray diffraction (XRD), Raman spectra, BET, oxygen storage capacity (OSC) and temperature-programmed reduction measurements (H₂-TPR) after calcination at 100 ℃, 300 ℃, 600 ℃, and 1 000 ℃. The results showed that the precipitation was a crystalline of fluorite structure, and in the process of the precipitation transformation into Ce_0.65Zr_0.35O₂ solid solution, the fluorite structure of the precipitation kept unchanged. The samples had different BET surface areas and OSC at different temperatures, but they held the performance of stable structure. After 1 000 ℃, there didn′t appear the other crystalline phase. So the samples prepared by co-precipitation method had excellent texture and higher thermal stability.     

Li1.02Cr0.1Mn1.9O4表面包覆的热稳定性研究

Improvement of elevated-temperature performance of Li_1.02Cr_0.1Mn_1.9O₄ cathode material by silicious surface modification was studied. The Li_1.02Cr_0.1Mn_1.9O₄ cathode material was treated by silanes coupling agent and then heated at 580 ℃ to remove organic material. The structures of the modified and unmodified Li_1.02Cr_0.1Mn_1.9O₄ were characterized by SpectraPlus, SEM and XRD. The results show that the surface layer of Li_1.02Cr_0.1Mn_1.9O₄ material is found to be rich in silicious compound. X-ray diffraction show that all the samples have perfect spinel structure. The electrochemical characterization of modified Li_1.02Cr_0.1Mn_1.9O₄ cathode material was tested. The cycle stability of charge/discharge at 55℃ is improved. The results of the charge/discharge curves show that the modified Li_1.02Cr_0.1Mn_1.9O₄ has better performance than those unmodified according to the inhibition of decline of reversible capacity of spinel Li_1.02Cr_0.1Mn_1.9O₄. Therefore, cycle performance is improved so obviously that 86.03% of the initial capacity is preserved after 100 cycles.     

电解质材料Sr-和Mg-掺杂LaGaO3的制备及性能研究

A dense La_0.8Sr_0.2Ga_0.83Mg_0.17O_2.815 electrolyte in pure perovskite phase was prepared by a polyacrylic acid assisted solid state reaction method, and the effects of La source on the structure and electrochemical performance were also studied. By means of XRD and SEM, the structure of this material was characterized, and the electrochemical properties were studied through AC impedance diagram. The results show that the sample presents a single perovskite-type phase after sintering at 1 450 ℃ and the relative density is 94%. The specimen has the lower activate energy and higher electrical conductivity at 600 ℃. There are two different activation energy at the turning point of 650 ℃, which are 74.6 and 42.4 kJ·mol^-1, respectively. The electrical conductivity is 0.057 S·cm^-1 and 0.017 S·cm^-1 at the temperature of 800 ℃ and 600 ℃, respectively.     

掺镍型层状LixNiyMn1-yO2正极材料的合成与电性能研究

A kind of cathode material of layered Li_xNi_yMn_1-yO₂ characterized with the O2 type has been synthesized by a simple method. Its precursor Na_xNi_yMn_1-yO₂ has been prepared from manganese dioxide， nickel hydroxide and sodium carbonate at high temperature in air and quickly cooled in cold water， then it has been exchanged by the melted LiNO₃ at 300～400℃ in air. The effects of calcine-temperature for the precursors and its compositions (the content of Na and Ni) on the electrochemical properties of the material Li_xNi_yMn_1-yO₂ have been investingated by XRD and electrochemical tests. The results show that the sample Li_0.7Ni_0.3Mn_0.7O₂， has the best electrochemical properties which shows only one charge-discharge potential stage of 2.8～3.0V and has a high specific capacity over 180mAh·g^-1 cycled between 2.0～4.20V. A significant structure transformation to the spinal-type phase has not been found in the charge-discharge cycling and the discharge specific capacity around 165mAh·g^-1 has re-mained after the 20th cyclings for the material.     

五元体系Li+/Cl-，CO32-，SO42-，B4O72--H2O 298 K相关系实验研究

Zabuye saline lake, Tibet, China, is unrivalled in the world for its high concentration of chloride, sulfate, carbonate and borate of lithium, sodium and potassium. Always at the later stage of the evaporation of brines, most sodium and potassium salts are crystallized out, so the main components of brines can be described with the Li⁺, Mg²⁺/Cl^-, SO₄^2-, CO₃^2-, B₄O₇^2--H₂O system. As a part of study on the equilibrium of this complex system, the equilibrium solubilities and phase diagram of the quinary system Li⁺/Cl^-，CO₃^2-，SO₄^2-，B₄O₇^2--H₂O at 298 K were studied by isothermal dissolution equilibrium method. In the 3-dimentional solubility diagram or its projection diagram saturated with solid LiCl, there are four crystallization fields, four univariant curves and one invariant point. At the invariant point, the saturated solid salts are LiCl·H₂O, Li₂B₄O₇·3H₂O, Li₂CO₃and Li₂SO₄·H₂O. No double salt or solid solution is formed.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

正丁胺对激光染料荧光谱影响的研究

用正丁胺作为碳源,采用射频辉光放电制备碳膜,选用激光染料R6G和聚乙二醇混合液作为蒸气源,采用单源热蒸发,在蒸发室与染料同时沉积得到混合膜,用拉曼光谱和红外光谱分析了碳膜的结构和键合方式,分析表明:碳膜中存在胺基团和氢原子.混合膜的荧光谱测量结果表明,认为正丁胺对染料荧光谱的影响是因为胺基和氢原子的存在.     

Cu0-catalysed 1,3-dipolar cycloadditions of α-amino acid derived N,N-cyclic azomethine imines to ynones

A series of 20 CuAIAC reactions between eight 4-acylamino substituted pyrazolidine-3-one-1-azomethine imines and four terminal ynones were performed using Cu⁰ as catalyst. The corresponding fluorescent cycloadducts were obtained in very high yields upon simple workup. Thus, Cu-metal turned out to be a better catalyst than Cu^I in terms of yield and ease of isolation. Availability of azomethine imines, mild reaction conditions, and simple workup enable a “click” access to libraries of densely substituted 2,3-dihydro-1H,5H-pyrazolo[1,2-a]pyrazol-1-ones. Reactivity of differently substituted dipoles was evaluated experimentally and by quantum chemical methods (DFT).     

Synthesis and antioxidative/anti-inflammatory activity of novel fullerene–polyamine conjugates

(E)-4-(Fullerenopyrrolidin-1-yl)-3-methylbut-2-enoic acid and its corresponding succinimidyl ester, readily obtained through Prato-type modification of C₆₀, were used for the selective N-acylation of polyamines. The thus obtained conjugates were evaluated for their antioxidative and anti-inflammatory activity and their cytotoxicity was determined. Members of this family of compounds showed interesting anti-lipid peroxidation, anti-lipoxygenase and anti-inflammatory activity and comparable cytocompatibility to spermidine.