MgCl2-KCl-NaCl-CaCl2熔盐电解镁机理

在725℃温度下,对MgCl2-KCl-NaCl-CaCl2熔盐体系进行电解.研究结果表明,镁电解过程中阴极过电压ηc只有12～51 mV,电解过程的过电压主要是由阳极引起的;阴极还原过程的极限扩散电流密度id为1.56 A/cm2;镁离子阴极放电反应的电子转移数为1.98;2个电子转移步骤之前存在着前置转化步骤MgCl+ Mg2++C1-.应用循环伏安法对4种不同配比下的镁离子行为进行的研究结果表明,CaCl2质量分数从10%增加到40%,维持MgCl2质量分数为10%以及NaCl与KCl的质量比为6: 1不变,随着CaCl2质量分数的增加,镁离子结合成不易移动的络合阴离子,镁离子迁移的电流分数减小,镁离子的析出电位从-1.595 V逐渐负移至与钙、钠共同沉积,阴极峰值电流Ipc值逐渐增大,阳极峰值电位与阴极峰值电位之差的绝对值|φpa-φpc|逐渐增大,阴极放电反应的可逆性逐渐降低.     

MgCl2-KCI—NaCI—CaCl2熔盐电解镁机理

在725℃温度下,对MgCl2-KCl-NaCl-CaCl2熔盐体系进行电解。研究结果表明,镁电解过程中阴极过电压ηc只有12～51mV,电解过程的过电压主要是由阳极引起的;阴极还原过程的极限扩散电流密度id为1．56A／cm^2;镁离子阴极放电反应的电子转移数为1．98：2个电子转移步骤之前存在着前置转化步骤MgCl^＋→Mg^2＋ ＋Cl^-。应用循环伏安法对4种不同配比下的镁离子行为进行的研究结果表明,CaCl2质量分数从10％增加到40％,维持MgCl2质量分数为10％以及NaCl与KCl的质量比为6：1不变,随着CaCl2质量分数的增加,镁离子结合成不易移动的络合阴离子,镁离子迁移的电流分数减小,镁离子的析出电位从-1．595V逐渐负移至与钙、钠共同沉积,阴极峰值电流Ipc值逐渐增大,阳极峰值电位与阴极峰值电位之差的绝对值｜φpa-φpc｜逐渐增大,阴极放电反应的可逆性逐渐降低。     

熔盐电解LiCl-KCl-AlCl3-La2O3共析出制备Al-Li-La合金

研究了LiCl-KCl-AlCl3-La2O3熔盐体系中共析出制备Al-Li-La合金的可行性。研究表明,在LiCl-KCl熔盐中,AlCl3将La2O3氯化为LaCl3,使电解制备Al-Li-La合金顺利进行。借助循环伏安法对熔盐体系的电化学行为进行分析发现,对质量比为45∶45∶5∶2的LiCl-KCl-AlCl3-La2O3熔盐,当阴极电流密度大于0.25 A/cm2,可以实现Al、Li和La的共析出。通过研究电解温度、阴极电流密度和电解时间对合金组成的影响,得到了较佳的电解参数:电解温度650℃,在LiCl-KCl混合熔盐中加入质量分数为5%的AlCl3和2%的La2O3,阴极电流密度12.5 A/cm2,电解时间1 h。X射线衍射对合金分析测试表明,合金主要由Al2La和βLi组成。     

熔盐电解法制备镁稀土合金的现状及展望

熔盐电解法是一种高效制备镁稀土合金的方法,工艺流程简便易于连续生产,而且制备的镁稀土合金成分均匀,不偏析。 不同稀土元素的熔盐体系也有所区别,重稀土元素一般采用氧化物电解法,而轻稀土元素则采用氯化物电解法。 针对以上不同的电解方法,本文从电解原料、电解槽结构、电极过程、电解工艺、尾气处理等多方面详细阐述了制备镁稀土合金的现状,并对电解法制备镁稀土合金的未来提出发展方向。     

KCl-LiCl-MgCl2熔盐体系中共电沉积制备Mg-Li合金及理论分析

在670 ℃的KCl-LiCl-MgCl₂熔盐体系中通过共电沉积方法制备了Mg-Li合金,并进行了理论分析。循环伏安表明：670 ℃时,锂在镁上(镁预先沉积到钼丝上)的欠电位沉积形成了液态的Mg-Li合金;当MgCl₂质量分数为10%时,出现了Mg-Li合金成核。极化曲线表明：在含有5% MgCl₂的熔盐中,MgCl₂的极限电流密度为0.35 A·cm^-2,超过此值时,Mg和Li就能产生共电沉积。对沉积物进行X射线衍射和电感耦合等离子体发射光谱(ICP)分析表明：通过恒电流电解得到了3种不同相的Mg-Li合金。在电流密度为6.21 A·cm^-2电解2 h条件下,只有当MgCl₂质量分数小于10%时,才能得到Mg-Li合金。并通过Nernst和浓差极化方程讨论了MgCl₂浓度对于Mg-Li合金形成的影响。Mg-Li合金中锂的含量能够通过熔盐中的MgCl₂浓度配比和电解参数来控制。实验证明这种直接从原料入手,通过共电沉积制备Mg-Li合金的新方法是可行的。     

NaCl-KCl-CeCl3熔盐体系电解精炼铈的研究

用Ce作为模拟金属,开展了NaCl-KCl-CeCl3熔盐体系电解精炼提纯金属Ce的研究,为乏燃料干法后处理提纯U, Pu等金属提供了研究基础。研究了CeCl3浓度、电解温度和阴极电流密度对电解精炼Ce的收率和电流效率的影响,得到优化的工艺条件为:CeCl3浓度为20%~25%,电解精炼温度为900~950℃,阴极电流密度为0.35~0.45 A·cm^-2,得到了成型致密的金属铈锭,产品的收率大于70%。杂质元素Al, Fe, Cu, Cr,Mn的含量均有大幅度的下降,尤其是Fe的去除效果明显从1300×10^-6降低为200×10^-6。     

熔盐电解制备CaB6晶体粉末及电极过程分析

研究采用CaCl2-NaCl混合熔盐电解制备CaB6晶体粉末的合成工艺,确定了电解反应的温度、电解电压、电解时间,对电流效率做了初步估算．同时,对电解生成的终产物的相组成、晶粒尺寸与形貌进行了X射线衍射、扫描电镜及能谱分析．实验结果表明,混合熔盐体系制备CaB6粉末的基本工艺条件是：氩气保护,电解槽电压2．8V,温度800℃下电解18h,所合成的CaB6粉末粒径范围为1～10μm,晶粒为规则的长方体．采用循环伏安法对电解阴极过程进行了定性分析．     

NdF3-LiF-Nd2O3熔盐体系中下阴极电解金属钕研究

设计了下阴极结构的稀土金属电解槽,该电解槽底部以钨材料为容器兼阴极,上部悬挂多块石墨作阳极,在NdF3·LiF-Nd2O3体系中,探索研究了液态下阴极电解制备金属钕的工艺技术条件.研究表明,在槽温990～1020℃,阴极电流密度1～3 A·cm-2.槽电压5.6 V条件下,电解可平稳进行,电流效率达65.64%,稀土回收率达88%～92%;该工艺与目前主流上插阴极电解工艺相比,其电解温度和槽电压明显降低,降低了电耗.     

稀土贮氢合金电极在乙醛酸电解制备中的应用

研究了以AB5型稀土贮氢合金作催化还原电极恒电位电解草酸制备乙醛酸,合金表面处理和电极活化可提高电解产率和电流效率.确定了最佳电解工艺条件:电流密度120mA·dm-2,电解液温度30℃,草酸浓度1.0mol·L-1,此时电流效率为86%,电解产率为88%.随着电解次数的增加,由于贮氢合金膨胀粉化及表面被电解产物覆盖,电流效率和乙醛酸产率均呈下降趋势,在电解过程中即时分离电解产物有利于提高电流效率和乙醛酸产率.     

尿素-NaBr低温熔盐中Fe2+和Sm3+的电化学行为及其诱导共沉积

利用循环伏安法、计时电位法和计时电流法 ,研究了尿素$CNaBr熔盐中Fe2 +在Pt,Cu ,Ag及Ti电极上的电化学行为 ,获知Fe2 +电还原为金属铁是一步不可逆过程 ,扩散系数为 2 74× 10 - 6cm2 ·s- 1 ,交换电流密度为 2 6 8× 10 - 5A·cm- 2 。使用循环伏安曲线和断电后的放电曲线研究熔体中Sm3 +的电化学行为 ,表明Sm3 +难以单独沉积 ,但通过加入Fe2 +可以诱导其共沉积。在Cu基体上进行恒电位和恒电流电解 ,得到Sm含量高于 90 % (质量分数 )的Sm Fe合金膜 ;发现Sm含量与阴极电位、电流密度以及SmCl3 /FeCl2 的摩尔比有关。用电镜研究了不同电解方法及钐含量对Sm$CFe合金表面的影响     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

恶臭嗅辨实验室建设探讨

针对恶臭测试的环境影响问题,提出了解决的实例方案,并对方案的要点及优缺点进行讨论,此方案在实际操作中具有较好的效果。     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.