Facile preparation of superhydrophobic coatings by sol-gel processes

Different organic/inorganic compositions and deposition methods were used to prepare superhydrophobic surfaces using metal alkoxides and the sol-gel process. Both surface roughness and composition had to be adjusted in order to obtain very high contact angles and low contact angle hysteresis as a necessary requirement for superhydrophobicity. Multilayer samples with a fluorinated organic-inorganic top layer showed water contact angles of about 157 degrees with low hysteresis (2 degrees ). Water drops rolled easily off their surface at a tilt angle as low as 4 degrees .     

Effects of contact angle hysteresis on ice adhesion and growth on superhydrophobic surfaces under dynamic flow conditions

In this paper, the icephobic properties of superhydrophobic surfaces are investigated under dynamic flow conditions using a closed-loop low-temperature wind tunnel. Superhydrophobic surfaces were prepared by coating aluminum and steel substrate plates with nano-structured hydrophobic particles. The superhydrophobic plates, along with uncoated controls, were exposed to a wind tunnel air flow of 12 m/s and ?7 °C with deviations of ±1 m/s and ±2.5 °C, respectively, containing micrometer-sized (～50 μm in diameter) water droplets. The ice formation and accretion were observed by CCD cameras. Results show that the superhydrophobic coatings significantly delay ice formation and accretion even under the dynamic flow condition of highly energetic impingement of accelerated supercooled water droplets. It is found that there is a time scale for this phenomenon (delay in ice formation) which has a clear correlation with contact angle hysteresis and the length scale of the surface roughness of the superhydrophobic surface samples, being the highest for the plate with the lowest contact angle hysteresis and finest surface roughness. The results suggest that the key for designing icephobic surfaces under the hydrodynamic pressure of impinging droplets is to retain a non-wetting superhydrophobic state with low contact angle hysteresis, rather than to only have a high apparent contact angle (conventionally referred to as a “static” contact angle).     

Ultralow hysteresis superhydrophobic surfaces by excimer laser modification of SU-8

We present a new and simple method to produce superhydrophobic surfaces with ultralow hysteresis. The method involves surface modification of SU-8 using an excimer laser treatment. The modified surface is coated with a hydrophobic plasma-polymerized hexafluoropropene layer. The advancing and receding water contact angles were measured to be approximately 165 degrees . The achieved water contact angle hysteresis was below the measurement limit. This low hysteresis can be ascribed to nanoscale debris generated during the excimer laser process.     

Superhydrophobicity on two-tier rough surfaces fabricated by controlled growth of aligned carbon nanotube arrays coated with fluorocarbon

Considerable effort has been expended on theoretical studies of superhydrophobic surfaces with two-tier (micro and nano) roughness, but experimental studies are few due to the difficulties in fabricating such surfaces in a controllable way. The objective of this work is to experimentally study the wetting and hydrophobicity of water droplets on two-tier rough surfaces for comparison with theoretical analyses. To compare wetting on micropatterned silicon surfaces with wetting on nanoscale roughness surfaces, two model systems are fabricated: carbon nanotube arrays on silicon wafers and carbon nanotube arrays on carbon nanotube films. All surfaces are coated with 20 nm thick fluorocarbon films to obtain low surface energies. The results show that the microstructural characteristics must be optimized to achieve stable superhydrophobicity on microscale rough surfaces. However, the presence of nanoscale roughness allows a much broader range of surface design criteria, decreases the contact angle hysteresis to less than 1 degrees , and establishes stable and robust superhydrophobicity, although nanoscale roughness could not increase the apparent contact angle significantly if the microscale roughness dominates.     

Contact line and contact angle dynamics in superhydrophobic channels

The dynamics of the wetting and movement of a three-phase contact line confined between two superhydrophobic surfaces were studied using a mean-field free-energy lattice Boltzmann model. Principle features of superhydrophobic surfaces, such as trapped vapor/air between rough microstructures, high contact angles, reduced contact angle hysteresis, and low resistance to fluid flow, were all observed. Movement of the three-phase contact line over a well-patterned superhydrophobic surface displays a periodic stick-jump-slip behavior, while the dynamic contact angle changes accordingly from maximum to minimum. Two regimes were found for the flow velocity as a function of surface roughness and can be related directly to the balance between driving force and flow resistance. This work provides a better understanding of dynamic wetting and fluid flow behaviors over superhydrophobic surfaces and hence could be useful in related applications.     

Condensation-induced wetting state and contact angle hysteresis on superhydrophobic lotus leaves

In this paper, we demonstrate how condensed moisture droplets wet classical superhydrophobic lotus leaf surfaces and analyze the mechanism that causes the increase of contact angle hysteresis. Superhydrophobic lotus leaves in nature show amazing self-cleaning property with high water contact angle (>150°) and low contact angle hysteresis (usually <10°), causing droplets to roll off at low inclination angles, in accordance with classical Cassie–Baxter wetting state. However, when superhydrophobic lotus leaves are wetted with condensation, the condensed water droplets are sticky and exhibit higher contact angle hysteresis (40–50°). Compared with a fully wetted sessile droplet (classical Wenzel state) on the lotus leaves, the condensed water droplet still has relatively large contact angle (>145°), suggesting that the wetting state deviates from a fully wetted Wenzel state. When the condensed water droplets are subjected to evaporation at room conditions, a thin water film is observed bridging over the micropillar structures of the lotus leaves. This causes the dew to stick to the surface. This result suggests that the condensed moisture does not uniformly wet the superhydrophobic lotus leaf surfaces. Instead, there occurs a mixed wetting state, between classical Cassie–Baxter and Wenzel states that causes a distinct increase of contact angle hysteresis. It is also observed that the mixed Cassie–Baxter/Wenzel state can be restored to the original Cassie–Baxter state by applying ultrasonic vibration which supplies energy to overcome the energy barrier for the wetting transition. In contrast, when the surface is fully wetted (classical Wenzel state), such restoration is not observed with ultrasonic vibration. The results reveal that although the superhydrophobic lotus leaves are susceptible to being wetted by condensing moisture, the configured wetting state is intermediate between the classical Cassie–Baxter and Wenzel states.     

Directing droplets using microstructured surfaces

Systematic variation of microscale structures has been employed to create a rough superhydrophobic surface with a contact angle gradient. Droplets are propelled down these gradients, overcoming contact angle hysteresis using energy supplied by mechanical vibration. The rough hydrophobic surfaces have been designed to maintain air traps beneath the droplet by stabilizing its Fakir state. Dimensions and spacing of the microfabricated pillars in silicon control the solid-liquid contact area and are varied to create a gradient in the apparent contact angle. This work introduces the solid-liquid contact area fraction as a new control variable in any scheme of manipulating droplets, presenting theory, fabricated structures, and experimental results that validate the approach.     

Design and fabrication of micro-textures for inducing a superhydrophobic behavior on hydrophilic materials

Artificial superhydrophobic surfaces are typically fabricated by tuning the surface roughness of intrinsically hydrophobic surfaces. We report here the design and fabrication of micro-textures for inducing a superhydrophobic behavior on hydrogen-terminated Si surfaces with an intrinsic water contact angle of approximately 74 degrees . The micro-textures consist of overhang structures with well-defined geometries fabricated by microfabrication technologies, which provide positions to support the liquid and prevent the liquid from entering into the indents between the micro-textures. As a result, water is in contact with a composite surface of solid and air, which induces the observed macroscopic superhydrophobic behavior.     

Effect of deposition parameters on the wettability and microstructure of superhydrophobic films with hierarchical micro-nano structures

Superhydrophobic films with hierarchical micro-nano structures were deposited on glass substrates by solution immersion method from a solution containing cobalt chloride, urea and cetyl trimethyl ammonium bromide (CTAB). Subsequently the films were hydrophobized with a low surface energy material like octadecanoic acid under ambient conditions resulting in superhydrophobic surfaces with water contact angle (WCA) of about 168° and contact angle hysteresis of 1°. The effect of deposition parameters such as solution composition, temperature, deposition time and alkanoic acid treatment on surface morphology and wettability of the films was studied. Mechanism of formation of cobalt chloride carbonate hydroxide film is discussed. Addition of CTAB to the solution resulted in a change in the surface morphology of the deposited films with flower-like structures. The wettability of films obtained under different process conditions was correlated to surface roughness using Wenzel and Cassie models.     

Modification of wetting properties of laser-textured surfaces by depositing triboelectrically charged Teflon particles

Hydrophilic laser-textured silicon wafers with natural oxide surfaces were rendered hydrophobic by depositing electrostatically charged submicrometer Teflon particles, a process termed as triboelectric Teflon adhesion. Silicon surfaces were micro-textured (～5 μm) by laser ablation using a nanosecond pulsed UV laser. By varying laser fluence, micro-texture morphology of the wafers could be reproduced and well controlled. Wetting properties of the triboelectrically charged Teflon-deposited surfaces were studied by measuring apparent static water contact angles and water contact angle hysteresis as a function of substrate roughness and the amount of Teflon deposited. A similar study was also performed on various micro-textured silicon carbide surfaces (sandpapers). If the average substrate roughness is between 15 and 60 μm, superhydrophobic surfaces can be easily formed by Teflon deposition with water contact angle hysteresis less than 8°. This environmentally benign solvent-free process is a highly efficient, rapid, and inexpensive way to render contact-charged rough surfaces hydrophobic or superhydrophobic.     

含氟硅丙烯酸酯乳液超疏水膜中疏水基团的梯度分布与表面微观结构研究

利用含氟疏水基团的梯度分布,结合草莓形纳米SiO2粒子提供的双重粗糙表面,制备了具有类"荷叶效应"的超疏水涂膜,水接触角达(174.2±2)°,滞后角几乎接近0°.通过原子力显微镜、扫描电镜和水接触角的测试对膜表面形貌及疏水性能进行了表征;探讨了其表面微观结构与表面疏水性能的关系.草莓形复合粒子在膜表面的无规则排列赋予涂膜表面不同等级的粗糙度,使水滴与涂膜表面接触时能够形成高的空气捕捉率,这种微观结构与疏水基团的梯度分布相结合,赋予了含氟硅丙烯酸酯乳液涂膜表面超疏水性能.     

Creation of “Rose Petal” and “Lotus Leaf” Effects on Alumina by Surface Functionalization and Metal‐Ion Coordination

Functional differences between superhydrophobic surfaces, such as lotus leaf and rose petals, are due to the subtle architectural features created by nature. Mimicry of these surfaces with synthetic molecules continues to be fascinating as well as challenging. Herein, we demonstrate how inherently hydrophilic alumina surface can be modified to give two distinct superhydrophobic behaviors. Functionalization of alumina with an organic ligand resulted in a rose‐petal‐like surface (water pinning) with a contact angle of 145° and a high contact angle hysteresis (±69°). Subsequent interaction of the ligand with Zn²⁺ resulted in a lotus‐leaf‐like surface with water rolling behavior owing to high contact angle (165°) and low‐contact‐angle‐hysteresis (±2°). In both cases, coating of an aromatic bis‐aldehyde with alkoxy chain substituents was necessary to emulate the nanowaxy cuticular feature of natural superhydrophobic materials.     

Poly[bis(2,2,2-trifluoroethoxy)phosphazene] superhydrophobic nanofibers

Nanofibers of poly[bis(2,2,2-trifluoroethoxy)phosphazene] were produced by electrospinning from solutions in tetrahydrofuran, methylethyl ketone, and acetone. The fiber diameter varied from 80 nm to 1.4 microm by changes in the concentration of the polymer solution. The electrospun nonwoven mats showed enhanced surface hydrophobicity compared to spun cast films with up to a 55 degrees increase in water contact angle. The hydrophobicity varied with fiber diameter and surface morphology, with contact angles to water being in the range of 135 degrees -159 degrees. A low value of hysteresis (<4 degrees) was recorded for the superhydrophobic surfaces. The extremely high hydrophobicity of these mats is a combined result of a fluorinated surface and the inherent surface roughness of an electrospun mat.     

Self-assembled monolayers of dendron thiols for electrodeposition of gold nanostructures: toward fabrication of superhydrophobic/superhydrophilic surfaces and pH-responsive surfaces

This paper describes the fabrication of surfaces with different wettability, superhydrophobic/superhydrophilic, and pH-responsive properties. We used a self-assembled monolayer (SAM) of a dendron thiol as the underlying surface for electrodeposition of gold nanostructures. After this modification with a SAM of n-dodecanethiol or 11-mercaptoundecanol, the surface shows remarkable superhydrophobic properties with a contact angle of about 155 degrees and a tilt angle of less than 2 degrees or superhydrophilic properties with a contact angle of about 0 degrees , respectively. Moreover, a large-scale pH-responsive surface was obtained by modification with 2-(11-mercaptoundecanamido)benzoic acid (7) (MUABA). The pH-responsive behavior was amplified by using rough surfaces.     

Contact angle hysteresis on regular pillar-like hydrophobic surfaces

A series of pillar-like patterned silicon wafers with different pillar sizes and spacing are fabricated by photolithography and further modified by a self-assembled fluorosilanated monolayer. The dynamic contact angles of water on these surfaces are carefully measured and found to be consistent with the theoretical predictions of the Cassie model and the Wenzel model. When a water drop is at the Wenzel state, its contact angle hysteresis increases along with an increase in the surface roughness. While the surface roughness is further raised beyond its transition roughness (from the Wenzel state to the Cassie state), the contact angle hysteresis (or receding contact angle) discontinuously drops (or jumps) to a lower (or higher) value. When a water drop is at the Cassie state, its contact angle hysteresis strongly depends on the solid fraction and has nothing to do with the surface roughness. Even for a superhydrophobic surface, the contact angle hysteresis may still exhibit a value as high as 41 degrees for the solid fraction of 0.563.     

Direct catalytic route to superhydrophobic polyethylene films

Polyethylene films grow on a flat silica surface modified by the bis(imino)pyridyl iron(II) catalyst during ethylene polymerization in toluene solvent. The resulting films show superhydrophobic properties. Advancing water contact angle as high as 169 degrees and sliding angles as low as 2 degrees are obtained on these films. SEM images reveal special surface structures of these films containing micrometer-sized islands, submicrometer particles on the islands, and stress nanofibers between the islands, which render superhydrophobicity to the polyethylene surfaces. After the submicrometer particles and stress nanofibers are removed by annealing, the superhydrophobic properties of the polymer films disappear.     

Fabrication of Superhydrophobic Surface with Different Metal Films on Aluminum Alloy

A simple technique was developed for the fabrication of a superhydrophobic surface on the aluminum alloy sheets. Different hierarchical structures(Ag, Co, Ni and Zn) were formed on the aluminum surface by the galvanic replacement reactions. After the chemical modification of them with fluorination, the wettability of the surfaces was changed from superhydrophilicity to superhydrophobicity. Scanning electron microscopy(SEM), energy dispersive spectrometry(EDS) and water contact angle measurement were performed to characterize the morphological characteristic, chemical composition and superhydrophobicity of the surfaces. The as-prepared superhydrophobic surfaces showed a water contact angle as high as ca.160° and sliding angle as low as ca.3°. We hope the method to produce superhydrophobic surface can be used in many fields.     

铝合金表面原位自组装超疏水膜层的制备及耐蚀性能

采用阳极氧化法在铝合金表面原位构造粗糙结构, 经表面自组装硅氧烷后得到超疏水自清洁表面, 与水滴的接触角最大可达157.5°±2.0°, 接触角滞后小于3°. 通过傅立叶变换红外(FT-IR)光谱分析仪、场发射扫描电子显微镜(FE-SEM)、能谱仪(EDS)、原子力显微镜(AFM)和接触角测试对阳极氧化电流密度、硅氧烷溶液中水的含量和自组装时间等参数进行了分析, 并得到制备超疏水自清洁表面的最优工艺参数. FE-SEM及AFM的测试结果表明, 由自组装硅氧烷膜层的无序性形成的纳米结构和阳极氧化构造的微米级粗糙结构与硅氧烷膜层的低表面能的协同作用构成了稳定的超疏水表面. 电化学测试(动电位极化)的结果表明, 原位自组装超疏水膜层极大地提高了铝合金的耐蚀性.     

Extremely superhydrophobic surfaces with micro- and nanostructures fabricated by copper catalytic etching

We demonstrate a simple method for the fabrication of rough silicon surfaces with micro- and nanostructures, which exhibited superhydrophobic behaviors. Hierarchically rough silicon surfaces were prepared by copper (Cu)-assisted chemical etching process where Cu nanoparticles having particle size of 10-30 nm were deposited on silicon surface, depending on the period of time of electroless Cu plating. Surface roughness was controlled by both the size of Cu nanoparticles and etching conditions. As-synthesized rough silicon surfaces showed water contact angles ranging from 93° to 149°. Moreover, the hierarchically rough silicon surfaces were chemically modified by spin-coating of a thin layer of Teflon precursor with low surface energy. And thus it exhibited nonsticky and enhanced hydrophobic properties with extremely high contact angle of nearly 180°.     

Superhydrophobic and low light reflectivity silicon surfaces fabricated by hierarchical etching

Silicon is employed in a variety of electronic and optical devices such as integrated circuits, photovoltaics, sensors, and detectors. In this paper, Au-assisted etching of silicon has been used to prepare superhydrophobic surfaces that may add unique properties to such devices. Surfaces were characterized by contact angle and contact angle hysteresis. Superhydrophobic surfaces with reduced hysteresis were prepared by Au-assisted etching of pyramid-structured silicon surfaces to generate hierarchical surfaces. Consideration of the Laplace pressure on hydrophobized hierarchical surfaces gives insight into the manner by which contact is established at the liquid/composite surface interface. Light reflectivity from the etched surfaces was also investigated to assess application of these structures to photovoltaic devices.