苄泽类非离子型表面活性剂与明胶的相互作用

采用表面张力和稳态荧光光谱法考察了具有不同疏水结构的2种苄泽类非离子型表面活性剂Brij58和Brij78与明胶之间的相互作用。结果表明,苄泽类非离子型表面活性剂与明胶之间相互作用的驱动力为疏水作用力,且两者之间的相互作用受到其疏水基团的影响,Brij78在明胶溶液中的临界聚集浓度低于Brij58体系,表明疏水链更长的Brij78与明胶之间的相互作用更强。明胶分子的内源荧光光谱强度受苄泽类非离子型表面活性剂的影响,但最大吸收峰位置未发生蓝移,Brij78/明胶体系的内源荧光强度高于Brij58/明胶体系;此外,表面活性剂浓度较低时,明胶的加入使溶液中疏水微区极性明显降低,且明胶浓度越大降低程度越大。     

表面活性剂对海藻酸钠稀水溶液剪切粘度的影响

通过粘度法考察了不同pH值时, 阴离子聚电解质海藻酸钠(NaAlg)与阴离子表面活性剂十二烷基硫酸钠(SDS)、阳离子表面活性剂十六烷基三甲基溴化铵(CTAB)、非离子表面活性剂辛基酚聚氧乙烯醚(TritonX-100)以及它们的复配体系的相互作用. 研究表明, 在酸性条件下, SDS和TritonX-100与NaAlg之间主要是疏水作用, 随着表面活性剂浓度的增加, 体系粘度下降直到基本不变, CTAB与NaAlg主要发生静电作用和疏水作用, 体系粘度随CTAB浓度的增加呈现先上升后下降的趋势. 在实验条件下, TritonX-100浓度为0.05 mmol·L-1时, SDS的加入, 使得NaAlg/TritonX-100体系的零剪切粘度下降, 而CTAB的加入, 在pH=3.0和5.0时, NaAlg/TritonX-100体系的零剪切粘度出现上升, 在pH=6.4时, 该体系零剪切粘度下降.     

Brij类表面活性剂与Laponite纳米颗粒的相互作用及其稳定乳液的研究

通过表面张力、Zeta电位和流变学参数的测定, 研究了聚氧乙烯烷基醚类非离子型表面活性剂(Brij 30和Brij 35)在合成锂皂石(Laponite)纳米颗粒表面的吸附及对Laponite水分散体系中颗粒间相互作用和体系粘度的影响. 结果表明, 这类表面活性剂能显著地吸附在Laponite颗粒表面上, 且吸附量随其分子中POE链长短而不同. 这种吸附没有改变Laponite粒子的带电性质, 但一定程度地降低了Laponite颗粒Zeta电位; 吸附也会减弱颗粒间的相互作用, 降低体系的粘度. 实验以Laponite和Brij为乳化剂, 制备了O/W型乳状液. 乳液稳定性变化和乳液粒径分布结果表明, 体系中Brij的浓度较低时, 乳液的性质主要是由Laponite颗粒决定的; 而Brij浓度较高时, 则主要取决于Brij表面活性剂. 高速剪切含Brij的Laponite水分散体系, 剪切后表面张力随时间的变化表明, 剪切作用会使得吸附在Laponite颗粒表面的Brij分子不同程度地解吸下来. 这也意味着乳液制备时, 高速剪切作用也会造成Brij分子自Laponite颗粒表面的脱附, 这可能是非离子表面活性剂与阳离子表面活性剂对负电固体颗粒稳定乳液影响不同的原因.     

烷基糖苷-十二烷基甜菜碱复配性能及无机盐的影响

考察了非离子型表面活性剂烷基糖苷(APG)和两性表面活性剂十二烷基甜菜碱(BS-12)之间的复配性能,测定了不同摩尔比的APG和BS-12复配体系的表面张力、泡沫和乳化性能,并且研究了无机盐对复配体系表面活性的影响。结果表明,与单独任一表面活性剂体系相比,APG和BS-12复配体系具有较好的表面活性,呈现明显的协同增效作用;在摩尔比为3∶7时,复配体系的表面活性最高、起泡性能最好、形成的泡沫和乳状液最稳定,协同增效作用最显著。此外,无机盐的加入提高了复配体系的表面活性,当NaCl浓度为0.03mol/L时,表面张力和临界胶束浓度最小,表面活性最高;而对于无机盐,其离子价态越高,提高表面活性程度越明显;相比之下,阳离子提高复配体系表面活性的能力大于阴离子。     

阴阳离子表面活性剂体系超低油水界面张力的应用

通过阴阳离子表面活性剂复配,在实际油水体系中获得了超低界面张力.通过在阴离子表面活性剂分子结构中加入乙氧基(EO)链段,以及采用阴阳离子加非离子型表面活性剂的三组分策略,有效解决了混合表面活性剂在水溶液中溶解度问题.进而研究了阳离子表面活性剂结构、非离子表面活性剂结构、三者组分配比、表面活性剂总浓度等因素对油水界面张力的影响,从而在胜利油田多个实际油水体系中获得了较大比例范围和较低浓度区域的油水超低界面张力,部分体系甚至达到了10-4 mN·m-1.由于阴阳离子表面活性剂间强烈的静电吸引作用,相关体系具有很好的抗吸附能力.经过石英砂48 h吸附后,体系仍然具有很好的超低界面张力.     

卵清蛋白与离子型表面活性剂的相互作用

本文通过荧光光谱法、紫外-可见吸收光谱法和透射电镜并结合电导率测定分别研究了水中卵清蛋白与阴离子表面活性剂十二烷基硫酸钠（SDS）和阳离子表面活性剂十二烷基三甲基溴化铵（DTAB）和十六烷基三甲基溴化铵（CTAB）之间的相互作用。研究结果表明卵清蛋白可以增加SDS和CTAB的临界胶束浓度,但对DTAB的临界胶束浓度没有影响。阴离子表面活性剂可以使卵清蛋白构象完全伸展,而阳离子表面活性剂却不具备此种作用。表面活性剂单体与卵清蛋白的相互作用强于表面活性剂胶束与卵清蛋白的相互作用。     

十二烷基甜菜碱/十二烷基硫酸钠复配体系的表面活性

研究了两性表面活性剂十二烷基甜菜碱（C12BE）和阴离子型表面活性剂十二烷基硫酸钠（SDS）复配体系的形成胶束能力,降低表面张力效率,降低表面张力能力三种增效作用.发现C12BE和SDS摩尔比为6 :4时增效作用最显著.并考察了盐、醇对复配体系表面活性的影响,结果表明,加盐能导致表面活性的提高,加醇的机理比较复杂,乙醇对复配体系表面活性影响不大,而正丁醇影响则比较显著.     

酯基Gemini型季铵盐表面活性剂与SDS的相互作用

研究了酯基Gemini型季铵盐表面活性剂[Cm-1H2m-1COOCH2CH2(CH3)2N+(CH2)n+N(CH3)2CH2CH2OOCCm-1H2m-1]•2Br-(简称II-m-n, m=10, 12; n=3, 4, 6)与十二烷基硫酸钠(SDS)的复配体系的相互作用以及无机盐(NaBr)对复配体系表面活性的影响. 结果发现, 其复配体系具有显著的胶团化协同增效作用和降低表面张力的增效作用, 并且II-10-n与SDS的复配体系的增效作用具有等链长效应. II-m-n/SDS复配体系的胶团化协同增效作用随n增大而增强. 混合胶团中II-m-n与SDS的摩尔比均近似为1:1, 显示各复配体系的混合胶团均带电性, 因此NaBr的加入能增强复配体系的表面活性和促进混合胶团的形成.     

吲哚方酸菁染料在表面活性剂水溶液中的光降解

考察了4种含有不同N位取代基的对称吲哚方酸菁染料在阳离子表面活性剂十六烷基三甲基溴化铵(CTAB)、阴离子表面活性剂十二烷基硫酸钠(SDS)和非离子表面活性剂曲拉通(TX-100)水溶液中的光降解行为,结果表明,表面活性剂对染料分子具有保护作用,其影响大小为CTAB>TX-100>SDS,分子中有羧基的染料受影响程度最大。在表面活性剂浓度较低时,染料光降解程度随着表面活性剂浓度的增加而增加,但形成胶束后,染料的光降解程度则随着表面活性剂浓度的升高而降低。     

阴/阳离子表面活性剂复配体系的中相微乳液研究

阴离子表面活性剂双-2-乙基己基磺化琥珀酸钠(简称AOT), 和阳离子表面活性剂十六烷基三甲基溴代铵(简称CTAB), 在有醇、正辛烷、盐水存在的情况下,能形成多相微乳液。本文系统地研究了阴/阳离子表面活性剂配比、醇的种类、醇的浓度对该体系的中相微乳液的形成及特性的影响, 得到了中相微乳液的特性参数(最佳含盐量S^*, 最佳中相微乳液体积V^*, 界面张力r~E、盐宽△S等)。这些性质对与阴/阳离子表面活性剂复配体系, 三次采油及日用化工上的应用开发具有重要意义。最后还开展单独阴离子表面活性剂体系和阴/阳离子表面活性剂复配体系进行了比较, 得到一些有价值规律, 并从理论上进行了探讨。     

THE EFFECTS OF MIXED MICELLES OF SURFACTANTS ON POLYMERIZATION OF ACRYLAMIDE

The polymerization of acrylamide in mixed micellar solutions of surfactants, initiated by NaHSO₃ has been studied at 20 and 3Q° C with time variable method of thermokinetics for 1. 5-order reaction. The results indicate that the mixed micellar systems of cationic or anionic with zwitterionic surfactants (SLS/ CTAB, SLS/ TTAB, SLS/ SDS) and cationic with nonionic surfactants (Brij 357sol; CTAB, Bri-J35/TTAB, Brij35/ DTAB) have catalytic effect on the polymerization in the order, at 20° C. SLS/ SDS SLS/ TTAB SLS/ CTAB Brij35/ CTAB at 30° C SLS/ SDS SLS/ TTAB≈ / CTAB Bri-j35/ DTAB= sBrij35/ TTAB as Brij35/ CTAB, while Brij35/ SDS mixed micellar system has inhibition. These effects are attributed to the effect of the Stern layer of mixed micelles on the step of initiator (HSOT) to form free radical.     

The Viscous Properties of Anionic/Cationic and Cationic/Nonionic Mixed Surfactant Systems

The behavior of mixed cationic/anionic and cationic/nonionic surfactants solutions have been studied by viscosimetry. The systems studied were sodium dodecyl sulfate (SDS)/cetyltrimethylammonium bromide (CTAB) and CTAB/Brij (polyoxyethylene lauryl ether, n = 10 and 23) in aqueous and sodium chloride solutions. The relative viscosity of single nonionic surfactant solutions is larger than that of SDS or CTAB solutions. It increases with the number of ethylene oxide groups. In the mixed systems, viscosity deviates from ideal behavior. The deviation results from electrostatic interactions. The surfactant mixture composition affects the self-assembled microstructure and rheology. A new mixed system that forms clear micellar solution above CMC was detected. In CTAB/Brij systems, the experimental data also deviate from ideal behavior due to mixed micelle formation and electroviscous effect. This effect is less pronounced than that of SDS/CTAB system and could be suppressed by adding an electrolyte (NaCl).     

Synergism and foaming properties in binary mixtures of a biosurfactant derived from Camellia oleifera Abel and synthetic surfactants

A biosurfactant, named tea saponin (TS), was isolated and purified from the defatted seed of Camellia oleifera Abel. The characterization of TS including molecular weight, glycosyl composition, and thermal behavior as well as the surface and foaming properties was conducted. The synergistic interactions of binary systems of CTAB-TS, SDS-TS, and Brij35-TS were investigated. The results show that TS had a weight-average molecular weight of 809.12 g mol(-1) and contained four aglycones of L-rhamnose, D-galactose, D-glucose, and D-glucuronic acid. The critical micelle concentration (cmc) of 2.242 mmol L(-1) and the minimum surface tension (γ(cmc)) of 43.5 mN m(-1) were determined for TS. Synergisms in surface tension reduction efficiency, in mixed micelle formation, and in surface tension reduction effectiveness were observed in CTAB-TS and SDS-TS systems, whereas that was not shown in Brij35-TS mixtures. The mixtures of TS with CTAB and SDS showed synergism in foaming efficiency, but this synergism did not exist in Brij35-TS system with respect to the surface properties. Nevertheless, there appears to be no significant correlation between foam stability and the surface properties.     

The Self-Association and Mixed Micellization of an Anionic Surfactant,Sodium Dodecyl Sulfate,and a Cationic Surfactant,Cetyltrimethylammonium Bromide: Conductometric,Dye Solubilization,and Surface Tension Studies

In the present study, we investigate the self-association and mixed micellization of an anionic surfactant, sodium dodecyl sulfate (SDS), and a cationic surfactant, cetyltrimethylammonium bromide (CTAB). The critical micelle concentration (CMC) of SDS, CTAB, and mixed (SDS + CTAB) surfactants was measured by electrical conductivity, dye solubilization, and surface tension measurements. The surface properties (viz., C₂₀ (the surfactant concentration required to reduce the surface tension by 20 mN/m), Π_CMC (the surface pressure at the CMC), Γ_max (maximum surface excess concentration at the air/water interface), and A_min (the minimum area per surfactant molecule at the air/water interface)) of SDS, CTAB, and (SDS + CTAB) micellar/mixed micellar systems were evaluated. The thermodynamic parameters of the micellar (SDS and CTAB), and mixed micellar (SDS + CTAB) systems were evaluated.

A schematic representation of micelles and mixed micelles.     

Self-motion of a camphanic acid disk on water with different types of surfactants

Control of the self-motion of a camphanic acid disk on water was investigated upon the addition of different kinds of surfactants (Triton X-100 and Brij58 as neutral surfactants, cetyltrimethylammonium bromide (CTAB) as a cationic surfactant, and sodium dodecyl sulfate (SDS) as an anionic surfactant) to the water phase. With an increase in the concentration of surfactant, continuous motion changed to no motion via intermittent motion (repetition between motion and rest), and the concentration regions of these motions were different among these surfactants. Although the concentration regions of these motions were determined by the surface tension for neutral surfactants, they were different than those for CTAB and SDS. These characteristics of self-motion are discussed in relation to the surface tension, depending on the concentration of individual surfactants, and the hydrophilic effect of the surfactants.     

Interaction of Nonionic Surfactant Triton-X-100 with Ionic Surfactants

The interaction in two mixtures of a nonionic surfactant Triton-X-100 (TX-100) and different ionic surfactants was investigated. The two mixtures were TX-100/sodium dodecyl sulfate (SDS) and TX-100/cetyltrimethylammonium bromide (CTAB) at molar fraction of TX-100, α_TX-100 = 0.6. The surface properties of the surfactants, critical micelle concentration (CMC), effectiveness of surface tension reduction (γ_CMC), maximum surface excess concentration (Γ_max), and minimum area per molecule at the air/solution interface (A _min) were determined for both individual surfactants and their mixtures. The significant deviations from ideal behavior (attractive interactions) of the nonionic/ionic surfactant mixtures were also determined. Mixtures of both TX-100/SDS and TX-100/CTAB exhibited synergism in surface tension reduction efficiency and mixed micelle formation, but neither exhibited synergism in surface tension reduction effectiveness.     

THE EFFECT OF MIXED MICELLES OF SURFACTANTS ON THE ALKALINE HYDROLYSIS OF ESTERS

The alkaline hydrolysis of aromatic and normal aliphatic acid esters have been studied at 25°C In mixed micellar solution of surfactants (Brij35—SDS, Brij35 — DTAB, Brij35—TTAB.Brij35-CTAB. Triton X—100 —CTAB, Triton X— 100 —SDS) with UV spectrophotometry and the method of thermokinetics The critical mice liar concentrations of the corresponding systems have also been measured with UV spectrophotometry in this paper. K_jnln micellar pseudo-phase has been calculated- The ratios of ki.to ki.for all mixed micellar systems Investigated are less than 1. The results indicate that these reactions are inhibited by the mixed micelles and the mixed micelles exhibit a greater effect of Inhibition on the reactions than those do In corresponding single ones. The reason for this is that the micropolarity of the compact Stern layer of mixed micelle is lower, and the micro viscidity Is higher. The Inhibition effect! also depend on the hydrophobic chain length of the surfactants and the hydrophobicity of the substrate.     

Synergistic effect of mixed anionic and cationic surfactant systems on the interfacial tension of crude oil-water and enhanced oil recovery

Surfactant based enhanced oil recovery (EOR) is an interesting area of research for several petroleum researchers. In the present work, individual and mixed systems of anionic and cationic surfactants consisting of sodium dodecyl sulphate (SDS) and cetyltrimethylammonium bromide (CTAB) in different molar ratios were tested for their synergistic effect on the crude oil-water interfacial tension (IFT) and enhanced oil recovery performance. The combination of these two surfactant systems showed a higher surface activity as compared to individual surfactants. The effect of mixed surfactant systems on the IFT and critical micellar concentration (CMC) is strongly depends on molar ratios of the two surfactant. Much lower CMC values were observed in case of mixed surfactant systems prepared at different molar ratios as compared to individual surfactant systems. The lowest CMC value was found when the molar concentration of SDS was higher than the CTAB. When the individual and mixed surfacant systems were tested for EOR performance through flooding experiments, higher ultimate oil recovery was obtained from mixed surfactant flooding compared to individual surfactants. Combination of SDS and CTAB or probably other anionic-cationic surfactants show synergism with substantial ability to reduce crude oil water IFT and can be a promising EOR method.     

Surfactant-induced electroosmotic flow in microfluidic capillaries

Control of EOF in microfluidic devices is essential in applications such as protein/DNA sizing and high‐throughput drug screening. With the growing popularity of poly(methyl methacrylate) (PMMA) as the substrate for polymeric‐based microfludics, it is important to understand the effect of surfactants on EOF in these devices. In this article, we present an extensive investigation exploring changes in EOF rate induced by SDS, polyoxyethylene lauryl ether (Brij35) and CTAB in PMMA microfluidic capillaries. In a standard protein buffer (Tris‐Glycine), PMMA capillaries exhibited a cathodic EOF with measured mobility of 1.54 ± 0.1 (× 10^?4 cm²/V.s). In the presence of surfactant below a critical concentration, EOF was independent of surfactant concentration. At high concentrations of surfactants, the electroosmotic mobility was found to linearly increase/decrease as the logarithm of concentration before reaching a constant value. With SDS, the EOF increased by 257% (compared to buffer), while it was decreased by 238% with CTAB. In the case of Brij35, the electroosmotic mobility was reduced by 70%. In a binary surfactant system of SDS/CTAB and SDS/Brij35, addition of oppositely charged CTAB reduced the SDS‐induced EOF more effectively compared to nonionic Brij35. We propose possible mechanisms that explain the observed changes in EOF and zeta potential values. Use of neutral polymer coatings in combination with SDS resulted in 50% reduction in the electroosmotic mobility with 0.1% hydroxypropyl methyl cellulose (HPMC), while including 2% poly (N,N‐dimethylacrylamide) (PDMA) had no effect. These results will potentially contribute to the development of PMMA‐based microfluidic devices.     

Effects of surfactant micelles on solubilization and DPPH radical scavenging activity of Rutin

The interaction of the antioxidant Rutin with the radical DPPH (2,2-diphenyl-1-picrylhydrazyl) in presence of cationic (CTAB, TTAB, DTAB), non-ionic (Brij78, Brij58, Brij35), anionic (SDS) and mixed surfactant systems (CTAB-Brij58, DTAB-Brij35, SDS-Brij35) has been followed by spectrophotometric and tensiometric methods to evaluate the DPPH radical scavenging activity (RSA) of Rutin in these model self-assembled structures. The results show that the solubilization capacity of various single surfactant systems for both DPPH as well as Rutin followed the order cationics > non-ionics > anionic. The radical scavenging activity of Rutin in the solubilized form was higher within ionic micelles than in non-ionic micelles. However, the antioxidant exhibited enhanced activity for the radical in mixed cationic-non-ionic micelles compared with any of the single component micelles. In contrast, anionic-non-ionic mixed micelles modulated the activity of Rutin in-between that seen for pure anionic and non-ionic micelles only.