PP-g-(MAH/St)和PP-g-MAH对聚丙烯/木粉复合材料性能的影响

在转矩流变仪中用熔融接枝法制备马来酸酐(MAH)和苯乙烯(St)接枝聚丙烯（PP）-PP-g-(MAH/St)和PP-g-MAH,将其作为聚丙烯/木粉复合材料的相容剂。 FTIR证实MAH和St单体与PP发生接枝反应。 用SEM和DSC等手段考察两种相容剂对PP/木粉复合材料微观形貌和结晶性能的影响,探索了各种PP/木粉复合材料加工和力学性能不同的内在原因。 SEM显示,PP-g-(MAH/St)改性木粉比PP-g-MAH改性木粉在PP基体中分散性更佳,木粉与PP的界面更加模糊,相容性进一步改善。 DSC结果表明,PP-g-(MAH/St)改性体系可增强木粉对PP的异相成核作用,提高结晶温度和结晶度。 复合材料的加工和力学性能测试结果表明,PP-g-(MAH/St)改性效果明显优于PP-g-MAH。 复合材料的熔体质量流动速率随相容剂用量的增加而逐步下降,PP-g-(MAH/St)改性体系拉伸强度和弯曲强度却逐步上升,并在相容剂用量为4.8 g/100 g PP时达到极值。 此时其拉伸强度达40.62 MPa,分别是未改性体系和PP-g-MAH改性体系的1.29和1.17倍;其弯曲强度达45.72 MPa,分别是未改性体系和PP-g-MAH改性体系的1.23和1.59倍;而无缺口冲击强度却在相容剂用量为3.6 g/100 g PP时达到极值13.35 kJ/m2,分别是未改性体系和PP-g-MAH改性体系的1.62倍和1.42倍。     

不同改性剂对聚丙烯/碳酸钙复合材料性能的影响

以马来酸酐(MAH)、聚丙烯蜡(PPW)为主要原料,采用原位固相接枝改性法制得PP/CaCO3-MAH-PPW复合材料,并与添加相容剂聚丙烯接枝马来酸酐(PP-g-MAH)所制得的PP/PP-g-MAH/CaCO3复合材料进行比较。结果表明,CaCO3良好的分散性及其与PP基体适宜的界面粘接是复合材料具有较好韧性的关键因素。与PP/PP-g-MAH/CaCO3复合材料相比,PP/CaCO3-MAH-PPW复合材料表现出更佳的冲击、弯曲和加工性能,当m(PP)∶m(CaCO3)=100∶20时,材料缺口冲击强度达到最大值,是基体树脂的1.19倍。     

超支化聚乙烯亚胺接枝二氧化硅的制备及在聚丙烯改性中的应用

首先利用3-缩水甘油氧基丙基三甲氧基硅烷(简称GPS)作为偶联剂,对纳米SiO2进行表面改性,获得表面含有环氧基的SiO2纳米粒子(SiO2-GPS).利用这些环氧基与超支化聚乙烯亚胺(HPEI)分子中的氨基进行反应,得到SiO2接枝超支化聚乙烯亚胺的纳米粒子(SiO2-GPS-g-HPEI).然后利用SiO2-GPS-g-HPEI与聚丙烯(PP)和PP接枝的马来酸酐(PP-g-MAH)共混、模压,制备PP/SiO2-GPS-g-HPEI/PP-g-MAH复合材料.红外光谱测试和热失重分析(TGA)测试结果表明,SiO2纳米粒子表面依次接枝了GPS和HPEI;扫描电子显微镜(SEM)的测试结果显示,SiO2-GPS-g-HPEI在聚丙烯基体中分散良好,其材料的冲击断裂为韧性断裂;复合材料共混时,扭矩的增加证明了共混物中分散相(SiO2-GPS-g-HPEI)与基体(PP/PP-g-MAH)界面之间存在一定的相互作用.少量SiO2-GPS-g-HPEI加入PP/PP-g-MAH中,冲击强度可增加96.3%,拉伸强度也有较大的提高.     

PP/PP-g-MAH与铝板粘接界面相的XPS研究

用X射线光电子能谱(XPS)研究铝板/聚丙烯层状复合材料的粘接界面相，提出了粘接界面的化学反应机制.研究发现,聚丙烯(PP)中加入马来酸酐接枝聚丙烯(PP-g-MAH)时，铝板面上Al 2p、O 1s谱线明显向高结合能端移动，表明PP-g-MAH与铝板表面发生了化学反应，形成Al－O－C配位键.配位键的形成使界面粘接强度明显提高. PP中不含PP-g-MAH时，铝板面上Al 2p、O 1s谱线处于低结合能端，聚丙烯未与铝板表面形成化学配位作用.     

马来酸酐-苯乙烯熔融接枝聚丙烯的影响因素及其性能研究

用单螺杆挤出机制备了马来酸酐 (MAH) 苯乙烯 (St)对聚丙烯 (PP)的多组分单体自由基熔融接枝体系 .研究证实了当两种单体物质的量比约为 1∶1时 ,接枝物的接枝率最高 ,而熔体流动速率 (MFR)最大 .对反应体系影响因素的研究表明单体用量和引发剂用量对不同单体用量比的系列接枝物的接枝率会产生不同的影响 ;另外 ,单体用量增加 ,接枝物的MFR减小 ,过氧化二异丙苯 (DCP)用量增加 ,接枝物的MFR增加 .对多单体熔融接枝聚丙烯PP g (MAH co St)的力学性能研究发现 ,选用合适的单体用量比、单体用量和DCP用量时 ,所制备的接枝物可具有与纯PP相当或更佳的力学性能     

均匀设计法研究丙烯酰胺在聚羟基丁酸-戊酸膜上的可控接枝

利用均匀设计和二次回归分析方法对聚羟基丁酸-戊酸P(HB-co-HV)膜的固相接枝聚合条件进行了研究,得到了膜接枝率与实验条件之间的回归数学模型。通过4组不同实验条件下的接枝聚合结果验证,利用该回归数学模型可以设计不同接枝率的实验条件,达到定量控制接枝率的目的。     

PP-g-MAH对聚丙烯/滑石粉复合材料的性能影响

研究了两种马来酸酐接枝聚丙烯（PP-g-MAH）在不同含量时对聚丙烯（PP）/滑石粉复合材料的力学性能、雾化性能和线性膨胀系数的影响.结果表明,接枝物的加入能提高复合材料的拉伸性能、冲击性能和弯曲性能,但随着含量的增加拉伸强度、冲击强度和弯曲强度及弯曲模量有所降低.在含量相同时,接枝物1对冷凝组份的影响更小.复合材料的线性膨胀系数随接枝物含量的增加先减小后增加.     

甲基丙烯酸缩水甘油酯/苯乙烯固相接枝聚丙烯

以苯乙烯(St)为共单体，过氧化苯甲酰(BPO)为引发剂，采用固相接枝反应将甲基丙烯酸缩水甘油酯(GMA)接枝到聚丙烯(PP)大分子链上。研究了反应时间、单体用量、引发剂用量等因素对接枝率的影响。采用凝胶渗透色谱(GPE)测定了PP和接枝物PP-g-(GMA-St)的分子量和分子量分布。结果 表明固相接枝PP反应条件为[GMA／[St]=2，反应3．5h，加入GMA 10份，BPO 5份。St的加入有助于GMA与PP的接枝，同时在一定程度上抑制了PP的降解。     

稀土化合物参与的聚丙烯反应挤出接枝马来酸酐

将多种稀土化合物用于等规聚丙烯(iPP)与马来酸酐(MAH)的接枝反应, 对接枝共聚物的结构、 接枝率和加工行为等进行了表征和研究. 结果表明, 稀土氧化物CeO2和Nd2O3的加入促进了iPP熔体接枝MAH的反应, 与未加入稀土化合物的接枝体系相比, MAH单体接枝率最大值分别提高了14%和25%, 同时接枝共聚物的熔体流动速率(MFR)也分别增大了34%和56%. 根据实验条件下接枝共聚物的MFR与MAH单体接枝率间的关系, 并结合熔体接枝反应机理, 提出了采用MFR来表征接枝率的方法, 并建立了工作曲线. 同时, 对不同稀土化合物抑制或促进熔体接枝反应发生的机理进行了初步探讨.     

PP/PMMA/PP-g-MAH共混物的结晶和相形态研究

采用偏光显微镜和相差显微镜详细研究PP/PMMA不相容聚合物共混物体系和PP/PMMA/PP-g-PMMA增容共混体系的结晶和相形态.偏光显微照片的研究结果表明,增容剂PP-g-MAH中PP结晶需要克服更多的能垒,导致PP结晶形态变得不完善,球晶尺寸变小.比较PP/PMMA和PP/PMMA/PP-g-MAH的相差显微照片可以看出,由于增容剂的加入,PP与PMMA相之间的界面变得模糊,两相的相容性变好.随着PP-g-MAH中MAH接枝率的增加,PMMA分散相的尺寸减小且变得均匀;当增容剂的接枝率为2.41%,添加的质量分数为4.71%,PP/PMMA共混体系中PMMA分散相的相?尺寸可达最小.PP-g-MAH作为反应型增容剂,一方面与PP在界面区域产生共晶;另一方面,MAH极性基团与PMMA的极性基团间产生的强的化学键合作用,使得界面区域的PP-g-MAH分子采取有利于降低构象熵的构象来起到增容作用.PP/PMMA共混物在130℃等温结晶的结果显示,PMMA相对PP的结晶形态的影响较小,PP结晶呈现典型的均相成核特征.PP/PMMA共混体系中加入PP-g-MAH,PP结晶尺寸减少.与非等温结晶相比,等温结晶的PP/PMMA共混物中PMMA相区尺寸明显偏大.     

β-Crystallisation tendency and structure of polypropylene grafted by maleic anhydride and its blends with isotactic polypropylene

Crystallization, melting and structure of three different commercial types of isotactic polypropylene (iPP) grafted by maleic anhydride (PP-g-MAH) with different maleic anhydride content (AC) and their β-nucleated versions were studied by X-ray diffractometry (WAXS), differential scanning calorimetry (DSC), polarised light microscopy (PLM) and scanning electron microscopy (SEM). The presence of maleic anhydride units disturbs the chain regularity, hereby decreases the crystallization tendency of iPP in general and the β-crystallisation ability in particular. β-modification of iPP (β-iPP) forms only in β-nucleated PP-g-MAH polymers studied if the anhydride content is not larger than 0.5 mass%. The influence of AC of PP-g-MAH on the feature the spherulitic structure is demonstrated by PLM and SEM micrographs. The β-nucleated iPP/PP-g-MAH blends containing 10 mass% PP-g-MAH crystallise predominantly in β-form independently of AC of the latter. The β-nuceated blends of iPP and PP-g-MAH with lowest AC crystallise in β-form in whole concentration range. The interaction parameter between iPP and PP-g-MAH polymers calculated by Nishi-Wang equation indicate limited interaction between the components.     

The effect of various compatibilizers on thermal,mechanical, and morphological properties of polystyrene/polypropylene blends

The effects of various compatibilizers on thermal, mechanical and morphological properties of 50/50 polypropylene/polystyrene blends were investigated. Various compatibilizers, polystyrene-(ethylene/butylenes/ styrene) (SEBS), ethylene vinyl acetate (EVA), polystyrene-butylene rubber (SBR) and blend of compatibilizers SEBS/PP-g-MAH, EVA/PP-g-MAH, and SBR/PP-g-MAH were used. Differential scanning calorimetry, thermogravimetric analysis, wide-angle X-ray scattering, scanning electron microscopy, microhardness, and Izod impact strength were adopted. It was found that the influence of various compatibilizers was appeared on all the properties studied. The properties of the blends compatibilized with SEBS, EVA, and SBR are very distinct from those of blends compatibilized with blend of compatibilizers. Results show that compatibilized blends with the blend of compatibilizers EVA/PP-g-MAH, SBR/PP-g-MAH, and SEBS/PP-g-MAH or SBR were relatively more stable than the uncompatibilized blend and blend compatibilized with SEBS or EVA. The compatibilizer does not only reduce the interfacial tension or increase the phase interfacial adhesion between the immiscible polymers, but greatly affects the degree of crystallinity of blends.

     

聚丙烯与马来酸酐在超临界CO2中的接枝聚合

聚丙烯(PP)以其强度高、耐热性好、密度小、易加工和价廉等特点成为重要的通用塑料。但由于非极性的分子结构,其亲水性、染色性、抗静电性、粘接性和印刷性并不理想,难以与极性聚合物和填料共混、复合。PP通过接枝引入极性基团是最常用的化学改性方法。常用的接枝单体有马来     

Preparation and characterization of graft copolymerization of ethyl acrylate onto hydroxypropyl methylcellulose in aqueous medium

Graft copolymerization of ethyl acrylate (EA) onto water-soluble hydroxypropyl methylcellulose (HPMC) was investigated with potassium persulfate (KPS) as initiator in an aqueous medium. The effects of monomer concentration, initiator concentration, matrix concentration, reaction temperature, reaction time and pre-interacting time in terms of percentage of grafting (G) and grafting efficiency (G _E) are discussed. The graft copolymers were characterized by Fourier transform infrared spectra (FTIR), scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction analysis (XRD) and differential scanning calorimetry (DSC). In addition, equilibrium humidity adsorption behavior of the pure grafted copolymers was also studied.     

Effect of Compatibilizer on Properties of Polypropylene Layered Silicate Nanocomposite

Polypropylene layered silicate nanocomposites based on muscovite clay were prepared via melt compounding using Thermo Haake internal mixer. Muscovite was organically modified with cetyltrimethylammonium bromide (CTAB). Poly(propylene-g-maleic anhydride) copolymer (PP-g-MAH) and polypropylene-methyl polyhedral oligomeric silsesquioxane (PP-POSS) were used as a compatibilizer in the nanocomposite system at concentration of 3.0 wt% based on muscovite content. Consequently effect of compatibilizer on the mechanical properties of the nano–composites was characterized. It was found that the PP-g-MAH compatibiliser possess better overall mechanical properties than the nanocomposites with PP-POSS compatibilizer. The reason was partly due to better adhesion provided by compatibilization effect of PP-g-MAH than PP-POSS as exhibited in scanning electron micrographs.     

ZnO纳米片/微棒复合体的制备、结构及光学性能

以十六烷基三甲基溴化铵(CTAB)为表面活性剂,以氯化锌和氢氧化钠为原料,在低温水热条件下制备出具有纳米片状接枝结构的ZnO微棒。通过扫描电镜(SEM)、X射线衍射(XRD)、透射电镜(TEM)、光致发光(PL)和拉曼光谱(Raman)对产物的形貌、晶体结构和光学性能进行了表征。结果表明,表面活性剂CTAB对产物最终形貌的形成具有重要作用;微棒表面所接枝的薄片为多晶结构;产物光致发光峰是较少见的弱蓝光发射与强红光发射;同时对这种ZnO微棒的生长机理进行了探讨。     

TiO2-SA纳米光催化材料接枝动力学、结构及性能

采用后处理表面改性法在纳米TiO₂表面接枝水杨酸(SA)(TiO₂-SA), 分别考察了超声搅拌、溶剂、物料比、pH值及温度等因素对接枝过程及光催化材料性能的影响, 并研究了接枝反应动力学. 通过傅里叶变换红外(FT-IR)光谱、X射线光电子能谱(XPS)、X射线衍射(XRD)等对TiO₂-SA纳米光催化材料进行了结构表征, 并提出了结构模型. 通过接触角测定、同步热分析(热重-差示扫描量热法(TG-DSC))、紫外-可见漫反射光谱(UV-VisDRS)、扫描电子显微镜(SEM)对光催化材料进行了性能表征. 结果表明, 水杨酸改性纳米TiO₂可以提高疏水性及分散性, 减缓在溶剂中的沉降速度, 并能稳定吸附在油-水界面, 实现了光谱响应范围向可见光的拓展. 在紫外光照射下, TiO₂-SA表现出优异的光催化降解硝基苯性能.     

Stimuli-responsive membranes through peroxidation radiation-induced grafting of 2-hydroxyethyl methacrylate (2-HEMA) onto isotactic polypropylene film (IPP)

Stimuli-responsive membranes were prepared by peroxidation radiation-induced grafting of 2-hydroxyethyl methacrylate (2-HEMA) onto IPP. The radioactive isotope ⁶⁰Co was used as the source of gamma radiation. A plausible mechanism of grafting has been proposed. Using this method, the degree of grafting and morphology could be controlled through the variation of reaction parameters such as total dose, inhibitor concentration, monomer concentration, reaction time, reaction temperature and solvents. Maximum percentage of grafting (210?%) was obtained at total radiation dose of 20?kGy. The graft copolymerization reaction was carried out for 3?h with 20?v/v% of the monomer (2-HEMA) in methanol at 85?°C using 0.06?wt% of FeCl₃ as inhibitor. The chemical structures of grafted membranes were characterized by Fourier transform infrared spectroscopy (FTIR) which indicates that HEMA has been grafted onto IPP. The atomic force microscopy (AFM), scanning electron microscopy (SEM) techniques were used to assess the morphological characterization of the membranes, revealing the roughness of the surface. These membranes were investigated for their swelling behavior. pH-sensitivity and the dyeability of the grafted and ungrafted membranes have also been studied.     

Preparation and crystallization behaviour of PP/PP-g-MAH/Org-MMT nanocomposite

The melt-direct intercalation method was employed to prepare polypropylene (PP)/maleic anhydride grafted polypropylene (PP-g-MAH)/organic-montmorillonite (Org-MMT), X-ray diffractometer was used to investigate the intercalation effect and crystallite size in composites and TEM micrograph to observe the dispersion of Org-MMT interlayers in polypropylene. The results showed that by introducing maleated polypropylene in PP/Org-MMT composite, macromolecule segments had intercalated into interlayer space of Org-MMT. As a result, Org-MMT interlayers were dispersed evenly in polypropylene and PP/PP-g-MAH/Org-MMT nanocomposite was synthesized. The crystallite size of nanocomposite perpendicular to the crystalline plane such as (0 4 0), (1 3 0), (1 1 1), (0 4 1) is smaller than that of pristine PP, which indicated that the crystallite size of PP in nanocomposite can be diminished by adding PP-g-MAH and Org-MMT in PP. Moreover, the nonisothermal crystallization kinetics of PP and PP/PP-g-MAH/Org-MMT nanocomposite was investigated by differential scanning calorimetry (DSC) with various cooling rates. The Avrami analysis modified by Jeziorny, Ozawa method and a method developed by Liu were employed to describe the nonisothermal crystallization process of these samples. The difference in the exponent n between PP and nanocomposite, indicated that nonisothermal kinetic crystallization corresponded to tridimensional growth with heterogeneous nucleation. The values of half-time, Z_c, F(T) and K(T) showed that the crystallization rate of composites was faster than that of PP at a given cooling rate.