Ultra‐high molecular weight styrenic block copolymer/TPU blends for automotive applications: Influence of various compatibilizers

Thermoplastic elastomers (TPEs) based on new generation ultrahigh molecular weight styrene‐ethylene‐butylene‐styrene (SEBS) and thermoplastic polyurethane (TPU) are developed and characterized especially for automotive applications. Influence of maleic anhydride grafted styrene‐ethylene‐butylene‐styrene (SEBS‐g‐MA) and maleic anhydride grafted ethylene propylene rubber (EPM‐g‐MA) as compatibilizers has been explored and compared on the blends of SEBS/TPU (60:40). The amount of compatibilizers was varied from 0 to 10 phr. Scanning electron microscopy (SEM) and atomic force microscopy (AFM) studies revealed the dramatic changes from a nonuniform to finer and uniform dispersed phase morphology. This was reflected in various mechanical properties. SEBS‐g‐MA modified blends showed higher tensile strength. EPM‐g‐MA modified blends also displayed considerable improvement. Elongation at break (EB) was doubled for the entire compatibilized blends. Fourier‐transform infrared spectrometry (FTIR) confirmed the chemical changes in the blends brought about by the interactions between blend components and compatibilizers. Both SEBS‐g‐MA and EPM‐g‐MA had more or less similar effects in dynamic mechanical properties of the blends. Additionally, melt rheological studies have also been pursued through a rubber process analyzer (RPA) to get a better insight.     

Evaluation of the SEBS copolymer in the compatibility of PP/ABS blends through mechanical,thermal, thermomechanical properties,and morphology

Polypropylene (PP) blends with acrylonitrile-butadiene-styrene (ABS) were prepared using the styrene-ethylene-butylene-styrene copolymer (SEBS) as a compatibilizing agent. The blends were prepared in a co-rotational twin-screw extruder and injection molded. Torque rheometry, Izod impact strength, tensile strength, heat deflection temperature (HDT), differential scanning calorimetry, thermogravimetry, and scanning electron microscopy properties were investigated. The results showed that there was an increase in the torque of PA6/ABS blends with SEBS addition. The PP/ABS/SEBS (60/25/15%) blend showed significant improvement in impact strength, elongation at break, thermal stability, and HDT compared with neat PP. The elastic modulus and tensile strength have not been significantly reduced. The degree of crystallinity and the crystalline melting temperature increased, indicating a nucleating effect of ABS. The PP/ABS blends compatibilized with 12.5% and 15% SEBS presented morphology with well-distributed fine ABS particles with good interfacial adhesion. As a result, thermal stability has been improved over pure PP and the mechanical properties have been increased, especially impact strength. In general, the addition of the SEBS copolymer as the PP/ABS blend compatibilizer has the advantage of refining the blend's morphology, increasing its toughness and thermal stability, without jeopardizing other PP properties.     

聚乳酸/乙烯-醋酸乙烯酯共聚物共混物的形态与黏弹行为

熔融共混制备了不同组分比的聚乳酸(PLA)/乙烯-醋酸乙烯酯共聚物(EVA)共混物,采用扫描电子显微镜(SEM)、溶剂选择性蚀刻和旋转流变仪研究了共混物不相容的相形态及其黏弹响应.研究结果表明,PLA/EVA共混物为典型的热力学不相容体系,两基体组分间的界面张力约为2.2 mN/m;因此随组分比的不同,共混物表现出"海-岛"分散和双连续的不相容相形态;体系中EVA的相反转浓度约为50 wt%～60 wt%,这与黏性模型对相反点预测的结果一致;与双连续相形态的体系相比,乳液模型能够更好的描述具有"海-岛"分散形态的体系的线性黏弹响应,共混体系相对较宽的相反转区域主要源于两组分间较大的弹性比以及EVA自身的屈服行为.     

Thermal behaviour of styrene butadiene rubber/poly(ethylene-co-vinyl acetate) blends

The thermal behaviour of styrene butadiene rubber (SBR)/poly (ethylene-co-vinyl acetate) (EVA) blends was studied by using thermogravimetry (TG) and differential scanning calorimetry (DSC). The effects of blend ratio, cross-linking systems and compatibilization on the thermal stability and phase transition of the blends were analyzed. It was found that the mass loss of the blends at any temperature was lower than that of the components, highlighting the advantage of blending SBR and EVA. The addition of compatibilizer was also found to improve the thermal stability. DSC studies indicated the thermodynamic immiscibility of SBR/EVA system even in the presence of the compatibilizer. This is evident from the presence of two different glass transition temperatures, corresponding to SBR and EVA phases in both compatibilized and uncompatibilized blends.     

Improvement of Impact Strength of Polylactide Blends with a Thermoplastic Elastomer Compatibilized with Biobased Maleinized Linseed Oil for Applications in Rigid Packaging

This research work reports the potential of maleinized linseed oil (MLO) as biobased compatibilizer in polylactide (PLA) and a thermoplastic elastomer, namely, polystyrene-b-(ethylene-ran-butylene)-b-styrene (SEBS) blends (PLA/SEBS), with improved impact strength for the packaging industry. The effects of MLO are compared with a conventional polystyrene-b-poly(ethylene-ran-butylene)-b-polystyrene-graft-maleic anhydride terpolymer (SEBS-g-MA) since it is widely used in these blends. Uncompatibilized and compatibilized PLA/SEBS blends can be manufactured by extrusion and then shaped into standard samples for further characterization by mechanical, thermal, morphological, dynamical-mechanical, wetting and colour standard tests. The obtained results indicate that the uncompatibilized PLA/SEBS blend containing 20 wt.% SEBS gives improved toughness (4.8 kJ/m²) compared to neat PLA (1.3 kJ/m²). Nevertheless, the same blend compatibilized with MLO leads to an increase in impact strength up to 6.1 kJ/m², thus giving evidence of the potential of MLO to compete with other petroleum-derived compatibilizers to obtain tough PLA formulations. MLO also provides increased ductile properties, since neat PLA is a brittle polymer with an elongation at break of 7.4%, while its blend with 20 wt.% SEBS and MLO as compatibilizer offers an elongation at break of 50.2%, much higher than that provided by typical SEBS-g-MA compatibilizer (10.1%). MLO provides a slight decrease (about 3 °C lower) in the glass transition temperature (T_g) of the PLA-rich phase, thus showing some plasticization effects. Although MLO addition leads to some yellowing due to its intrinsic yellow colour, this can contribute to serving as a UV light barrier with interesting applications in the packaging industry. Therefore, MLO represents a cost-effective and sustainable solution to the use of conventional petroleum-derived compatibilizers.     

Compatibilizing effect of functionalized polystyrene blends: a study of morphology,thermal, and mechanical properties

Polystyrene (PS), being an amorphous polymer is immiscible with other polymers. To engender miscible blends, PS has been functionalized with an active amino‐functional group on the molecular chains of PS to yield amino‐substituted polystyrene (APS), which serves as a reactive compatibilizer. The compatibilization effect of amino functionalized polystyrene on the rubber toughening was explored and results were compared in terms of morphology, thermal, and mechanical properties of PS/SEBS‐g‐MA versus APS/SEBS‐g‐MA blends. In addition, the effect of rubber content on the blend morphology and mechanical properties were investigated. An appreciable change in the thermal stability of APS blends in comparison with PS blend has been probed. A marked correlation has been observed between phase morphology and thermal stability. Use of APS produced the compatibilized blends which render improved blend morphology, enhanced thermal and mechanical properties. Optimal thermal, morphological and mechanical profiles were depicted by 20‐wt% APS blend. Copyright © 2008 John Wiley & Sons, Ltd.     

Effects of poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] on the charge distributions of low‐density polyethylene/polystyrene blends

The effect of the triblock copolymer poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] (SEBS) on the formation of the space charge of immiscible low‐density polyethylene (LDPE)/polystyrene (PS) blends was investigated. Blends of 70/30 (wt %) LDPE/PS were prepared through melt blending in an internal mixer at a blend temperature of 220 °C. The amount of charge that accumulated in the 70% LDPE/30% PS blends decreased when the SEBS content increased up to 10 wt %. For compatibilized and uncompatibilized blends, no significant change in the degree of crystallinity of LDPE in the blends was observed, and so the effect of crystallization on the space charge distribution could be excluded. Morphological observations showed that the addition of SEBS resulted in a domain size reduction of the dispersed PS phase and better interfacial adhesion between the LDPE and PS phases. The location of SEBS at a domain interface enabled charges to migrate from one phase to the other via the domain interface and, therefore, resulted in a significant decrease in the amount of space charge for the LDPE/PS blends with SEBS. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2813–2820, 2004     

Effect of EVA copolymer containing different VA content on the thermal and rheological properties of bio-based high-density polyethylene/ethylene vinyl acetate blends

The effect of ethylene vinyl acetate (EVA) concentration and vinyl acetate (VA) content of EVA on the mechanical, morphological, and rheological properties of bio-based high-density polyethylene (BioPE)/EVA blends was investigated. The blends were characterized by X-ray diffraction, differential scanning calorimetry, scanning electron microscopy, and rheological measurements under oscillatory shear flow. The degree of crystallinity of BioPE decreased with the increase in the EVA concentration and was unaffected with the increase in the VA content. DMTA results showed a decrease in the storage modulus (E′) with the increase in EVA content and that the BioPE/EVA19 blends showed higher E′ values than BioPE/EVA28 blend. The impact strength substantially increased with the addition of EVA concentration above 5 mass% and was higher for the blends containing the highest VA content. The blends containing a higher content of VA exhibited the higher EVA dispersed phase domain size, which increased with the increase in EVA concentration. The complex viscosity increased with the increase in the EVA content, being higher for the BioPE/EVA blends containing higher VA content. The storage modulus increased, at low frequencies, with the increase in the EVA content and can be ascribed to the increase in the EVA dispersed phase domain size.

     

Effects of different types of polyethylene on the morphology and properties of recycled poly(ethylene terephthalate)/polyethylene compatibilized blends

Recycled poly(ethylene terephthalate) (R‐PET) was blended with four types of polyethylene (PE), linear low density polyethylene (LLDPE; LL0209AA, Fs150), low density polyethylene (LDPE; F101‐1), and metallocene‐LLDPE (m‐LLDPE; Fv203) by co‐rotating twin‐screw extruder. Maleic anhydride‐grafted poly(styrene‐ethylene/butyldiene‐styrene) (SEBS‐g‐MA) was added as compatibilizer. R‐PET/PE/SEBS‐g‐MA blends were examined by scanning electron microscopy (SEM), differential scanning calorimeter (DSC), dynamic mechanical analysis (DMA), and mechanical property testing. The results indicated that the morphology and properties of the blends depended to a great extent on the miscibility between the olefin segments of SEBS‐g‐MA and PE. Due to the proper interaction between SEBS‐g‐MA and LDPE (F101‐1), most SEBS‐g‐MA, located at the interface between two phases of PET and LDPE to increase the interfacial adhesion, lead to better mechanical properties of R‐PET/LDPE (F101‐1) blend. However, both the poor miscibility of SEBS‐g‐MA with LLDPE (LL0209AA) and the excessive miscibility of SEBS‐g‐MA with LLDPE (Fs150) and m‐LLDPE (Fv203) reduced the compatibilization effect of SEBS‐g‐MA. DSC results showed that the interaction between SEBS‐g‐MA and PE obviously affected the crystallization of PET and PE. DMA results indicated that PE had more influence on the movement of SEBS‐g‐MA than PE did. Copyright © 2010 John Wiley & Sons, Ltd.     

A comparative study of effects of SEBS and EPDM on the water tree resistance of cross-linked polyethylene

In this work, we investigated the effects of an ethylene propylene diene monomer (EPDM) and poly[styrene-b-(ethylene-co-butylene)-b-styrene] (SEBS) on the water tree resistance in cross-linked polyethylene (XLPE). The XLPE/EPDM and XLPE/SEBS blend samples were prepared by melting compounding and subsequent compression molding. It was found that SEBS could greatly increase the water tree resistance of XLPE and the resistance performance was improved with SEBS content within 15 phr, whereas EPDM did not show any improvement in the water tree resistance of XLPE. The frequency dependent behaviors of the water treeing phenomena and the effects of EVA on the water tree resistance of XLPE/EPDM and XLPE/SEBS blends were also investigated. The water treeing phenomena of the blends were interpreted from the viewpoints of electro-mechanical and electro-chemical mechanisms.     

Rheology, morphology and mechanical properties of polyethylene/ethylene vinyl acetate copolymer (PE/EVA) blends

Rheology, morphology and mechanical properties of binary PE and EVA blends together with their thermal behavior were studied. The results of rheological studies showed that, for given PE and EVA, the interfacial interaction in PE-rich blends is higher than EVA-rich blends, which in turn led to finer and well-distributed morphology in PE-rich blends. Using two different models, the phase inversion composition was predicted to be in 45 and 47 wt% of the PE phase. This was justified by morphological studies, where a clear co-continuous morphology for 50/50 blend was observed. The tensile strength for PE-rich blends showed positive deviation from mixing rule, whereas the 50/50 blend and EVA-rich blends displayed negative deviation. These results were in a good agreement with the results of viscoelastic behavior of the blends. The elongation at break was found to follow the same trend as tensile strength except for 90/10 PE/EVA blend. The latter was explained in terms of the effect of higher co-crystallization in 90/10 composition, which increased the tensile strength and decreased the elongation at break in this composition. The results of thermal behavior of the blends indicated that the melting temperatures of PE and EVA decrease and increase, respectively, due to the dilution effect of EVA on PE and nucleation effect of PE on EVA.     

Thermal, ozone and gamma ageing of styrene butadiene rubber and poly(ethylene-co-vinyl acetate) blends

Ageing behaviour of SBR/EVA blends due to the effects of heat, ozone, and gamma radiation was studied with reference to blend ratio, three crosslinking systems (sulfur, peroxide and mixed) and a compatibiliser (SEBS-g-MA). It was found that an increase in the EVA content of the blends enhanced the ageing characteristics. Among the different crosslinking systems, a peroxide cured system exhibited the best retention of properties even after severe ageing. Tensile strength of peroxide cured SBR/EVA blends increased slightly after ageing for three days at 70 °C due to continued crosslinking, whereas tensile strength of all blends decreased on ageing at 100 °C. Compatibilisation with SEBS-g-MA improved the thermal, gamma and water ageing resistance of SBR/EVA blends.     

Compatibilization of Poly(Lactic Acid) (PLA)/Plasticized Cellulose Acetate Extruded Blends through the Addition of Reactively Extruded Comb Copolymers

In the perspective of producing a rigid renewable and environmentally friendly rigid packaging material, two comb-like copolymers of cellulose acetate (AC) and oligo(lactic acid) OLA, feeding different percentages of oligo(lactic acid) segments, were prepared by chemical synthesis in solvent or reactive extrusion in the melt, using a diepoxide as the coupling agent and were used as compatibilizers for poly(lactic acid)/plasticized cellulose acetate PLA/pAC blends. The blends were extruded at 230 °C or 197 °C and a similar compatibilizing behavior was observed for the different compatibilizers. The compatibilizer C1 containing 80 wt% of AC and 14 wt% of OLA resulted effective in compatibilization and it was easily obtained by reactive extrusion. Considering these results, different PLAX/pAC(100-X) compounds containing C1 as the compatibilizer were prepared by extrusion at 197 °C and tested in terms of their tensile and impact properties. Reference materials were the uncompatibilized corresponding blend (PLAX/pAC(100-X)) and the blend of PLA, at the same wt%, with C1. Significant increase in Young’s modulus and tensile strength were observed in the compatibilized blends, in dependence of their morphologic features, suggesting the achievement of an improved interfacial adhesion thanks to the occurred compatibilization.     

Correlation of Morphology Evolution with Superior Mechanical Properties in PA6/PS/PP/SEBS Blends Compatibilized by Multi-phase Compatibilizers

In this study,the maleic anhydride(MAH)and styrene(St)dual monomers grafted polypropylene(PP)and poly[styrene-b-(ethylene-co-butylene)-b-styrene](SEBS),i.e.PP-g-(MAH-co-St)and SEBS-g-(MAH-co-St)are prepared as multi-phase compatibilizers and used to compatibilize the PA6/PS/PP/SEBS(70/10/10/10)model quaternary blends.Both PS and SEBS are encapsulated by the hard shell of PP-g-(MAH-co-St)in the dispersed domains(about 2μm)of the PA6/PS/PP-g-(MAH-co-St)/SEBS(70/10/10/10)quaternary blend.In contrast,inside the dispersed domains(about 1μm)of the PA6/PS/PP/SEBS-g-(MAH-co-St)(70/10/10/10)quaternary blend,the soft SEBS-g-(MAH-co-St)encapsulates both the hard PS and PP phases and separates them.With increasing the content of the compatibilizers equally,the morphology of the PA6/PS/(PP+PP-g-(MAH-co-St))/(SEBS+SEBS-g-(MAH-co-St))(70/10/10/10)quaternary blends evolves from the soft(SEBS+SEBS-g-(MAH-co-St))encapsulating PS and partially encapsulating PP(about 1μm),then to PS exclusively encapsulated by the soft SEBS-g-(MAH-co-St)and then separated by PP-g-(MAH-co-St)inside the smaller domains(about 0.6μm).This morphology evolution has been well predicted by spreading coefficients and explained by the reaction between the matrix PA6 and the compatibilizers.The quaternary blends compatibilized by more compatibilizers exhibit stronger hierarchical interfacial adhesions and smaller dispersed domain,which results in the further improved mechanical properties.Compared to the uncompatibilized blend,the blend with both 10 wt%PP-g-(MAH-co-St)and 10 wt%SEBS-g-(MAH-co-St)has the best mechanical properties with the stress at break,strain at break and impact failure energy improved significantly by 97%,71%and 261%,respectively.There is a strong correlation between the structure and property in the blends.     

Highly toughened poly(lactic acid) (PLA) prepared through melt blending with ethylene-co-vinyl acetate (EVA) copolymer and simultaneous addition of hydrophilic silica nanoparticles and block copolymer compatibilizer

In this study, a highly toughened PLA was prepared through physical melt-blending with EVA at the presence of hydrophilic nanosilica and SEBS-g-MA block copolymer compatibilizer. The effect of nanosilica and compatibilizer on the morphology, mechanical properties, and linear rheology of the PLA/EVA blends was also investigated. According to TEM images, nanosilica was selectively located in the PLA matrix while some were placed on the interface between the two polymers as was also predicted by thermodynamic and kinetic analysis. Upon the addition of nanoparticles, the interfacial adhesion between the phases was enhanced and the average droplet size decreased. Interestingly, incorporation of SEBS-g-MA induced morphological changes as the spherical EVA droplets turned into a cylindrical shape. DSC results indicated that blending with EVA copolymer resulted in the reduction of crystallization of PLA matrix; however, the crystallinity increased at the presence of nanoparticles up to 5 wt%. The addition of compatibilizer considerably hindered the crystallization of the PLA phase. PLA/EVA blend containing optimum levels of nanosilica exhibited considerably enhanced tensile toughness, elongation at break, and impact strength. On the other hand, the simultaneous addition of nanoparticles and SEBS-g-MA led to synergistic toughening effects and the compatibilized blend containing nanosilica exhibited excellent impact toughness. For instance, the elongation at break of the compatibilized PLA/EVA blend containing the optimal content of nanosilica was increased from 7% to 121% (compared to neat sample). The notched Izod impact strength was also increased from 5.1 to 65 kJ/m². Finally, the microstructure of the blends was assessed by rheological measurements.     

Block copolymers as compatibilizers for blends of linear low density polyethylene and polystyrene

Compatibilization of blends of linear low-density polyethylene (LLDPE) and polystyrene (PS) with block copolymers of styrene (S) and butadiene (B) or hydrogenated butadiene (EB) has been studied. The morphology of the LLDPE/PS (50/50) composition typically with 5% copolymer was characterized primarily by scanning electron microscopy (SEM). The SEB and SEBS copolymers were effective in reducing the PS domain size, while the SB and SBS copolymers were less effective. The noncrystalline copolymers lowered the tensile modulus of the blend by as much as 50%. Modulus calculations based on a coreshell model, with the rubbery copolymer coating the PS particle, predicted that 50% of the rubbery SEBS copolymer was located at the interface compared to only 5–15% of the SB and SBS copolymers. The modulus of blends compatibilized with crystalline, nonrubbery SEB and SEBS copolymers approached Hashin's upper modulus bound. An interconnected interface model was proposed in which the blocks selectively penetrated the LLDPE and PS phases to provide good adhesion and improved stress and strain transfer between the phases. © 1995 John Wiley & Sons, Inc.     

界面张力对高分子共混物梯度相形态形成的影响研究

研究了界面张力对ＰＰ／ＥＶＡ共混体系梯度相形态形成的影响。首先将ＥＶＡｃ进行皂化反应得到一系列－ＯＨ基含量不同即极性不同的ＥＶＡ，然后将这些ＥＶＡ分别与ＰＰ共混从而得到一系列相界面张力不同的共混物。说明通过对共混物相界面张力的调整，可以达到随意控制梯度相形态形成速度的目的。     

Foaming behavior of polypropylene/polystyrene blends enhanced by improved interfacial compatibility

A series of polypropylene (PP)/polystyrene (PS) blends were prepared by solvent blending with PS‐grafted PP copolymers (PP‐g‐PS) having different PS graft chain length as compatibilizers. The interfacial compatibility was significantly improved with increasing PS graft chain length until the interface was saturated at PS graft chain length being 3.29 × 10³ g/mol. The blends were foamed by using pressure‐quenching process and supercritical CO₂ as the blowing agent. The cell preferentially formed at compatibilized interface because of low energy barrier for nucleation. Combining with the increased interfacial area, the compatibilized interface lead to the foams with increased cell density compared to the uncompatibilized one. The increase in interfacial compatibility also decreased the escape of gas, held more gas for cell growth, and facilitated the increase in expansion ratio of PP/PS blend foams. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1641–1651, 2008     

氢化苯乙烯-丁二烯-苯乙烯嵌段共聚物及其马来酸酐接枝共聚物增韧聚对苯二甲酸乙醇酯共混材料的辐射效应

采用双螺杆熔融共混的方法制备了含三羟甲基丙烷三丙烯酸酯(TMPTA)的聚对苯二甲酸乙二酯/氢化苯乙烯-丁二烯-苯乙烯嵌段共聚物（PET/SEBS）和聚对苯二甲酸乙二酯/马来酸酐接枝氢化苯乙烯-丁二烯-苯乙烯嵌段共聚物（PET/SEBS-g-MAH）共混材料,并在Co-60源中对其进行辐照。 通过对共混材料的力学性能、相态结构测和凝胶含量分析,对比研究了辐射对以上2种共混材料结构及性能的影响。 扫描电子显镜观察和凝胶含量分析结果表明,在适量TMPTA存在时,辐射有效地改善了PET/SEBS体系的相容性。 冲击强度的变化证实了这种增容效应,当SEBS的质量分数为20%、TMPTA质量分数为1%,经50 kGy辐照后,冲击强度达到17.3 kJ/m2。 当在SEBS分子链上引入马来酸酐官能团,辐照后,体系的相态结构变化并不明显,冲击强度最大值仅为11.5 kJ/m2,明显低于不含马来酸酐官能团的体系。     

The compatibilization effect of ethylene/styrene interpolymer on polystyrene/polyethylene blends

In this study, ethylene/styrene interpolymer (ESI) was used as compatibilizer for the blends of polystyrene (PS) and low‐density polyethylene (LDPE). The mechanical properties including impact, tensile properties, and morphology of the blends were investigated by means of uniaxial tension, instrumented falling‐weight impact measurements, and scanning electron microscopy. Impact measurements indicated that the impact strength of the blends increases slowly with LDPE content up to 40 wt %; thereafter, it increases sharply with increasing LDPE content. The impact energy of the LDPE‐rich blends exceeded that of pure LDPE, implying that the LDPE polymer can be further toughened by the incorporation of brittle PS minor phase in the presence of ESI. Tensile tests showed that the yield strength of the PS/LDPE/ESI blends decreases considerably with increasing LDPE content. However, the elongation at break of the blends tended to increase significantly with increasing LDPE content. The compatibilization efficiency of ESI and polystyrene‐hydrogenated butadiene‐polystyrene triblock copolymers (SEBS) for PS/LDPE 50/50 was further compared. Mechanical properties show that ESI is more effective to achieve a combination of LDPE toughness and PS rigidity than SEBS. The correlation between the impact property and morphology of the ESI‐compatibilized PS/LDPE blends is discussed. The excellent tensile ductility of the LDPE‐rich blends resulted from shield yielding of the matrix. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2136–2146, 2007