含石墨烯的聚乳酸复合纳米纤维的制备及细胞相容性

利用电纺丝技术制备了聚乳酸(PLLA)-石墨烯(Gr)复合纳米纤维.通过SEM、TEM及拉曼光谱观察和分析了该复合纳米纤维的形貌及Gr在PLLA中的分散状态,通过DSC、TG、力学拉伸及接触角测试等表征方法研究了PLLA-Gr复合纳米纤维的热性能、力学性能、亲水性等物理性能,最后,通过MTT法检测一种神经胶质细胞——雪旺细胞(SCs)在该复合纳米纤维支架上的生长和增殖行为,评价其细胞相容性.结果表明:低含量的Gr能较好地分散在PLLA纳米纤维中,且随着m(Gr)∶m(PLLA)从0增加到2.0％,所得到的纤维直径呈现先减小后增加的趋势.当m(Gr)∶m(PLLA)增加到1.0％时,PLLA Gr纳米纤维的直径达到最小,为(0.50±0.19) μm,对应的拉伸强度较未添加Gr时增加也最大达50％.PLLA-Gr纳米纤维膜的结晶度与Gr的含量和分散性有关.细胞培养1、4、7d后的MTT检测结果表明PLLA-Gr复合纳米纤维能促进SCs的黏附和生长.PLLA-Gr复合纳米纤维具有较好的细胞相容性.     

静电纺空气过滤用PET/CTS抗菌复合纳米纤维膜的制备

采用静电纺丝法制备PET/CTS复合纳米纤维膜,并在纤维膜表面吸附一层纳米银,进一步增加纤维膜的抗菌性能.以扫描电镜(SEM)对不同配比PET/CTS所制备的纤维膜的微观形貌进行表征,结果显示w(CTS)/w(PET)为12.5%时,纤维形貌较好,平均直径为405 nm.分别对不同厚度的PET/CTS纤维膜进行力学性能、透气性能以及空气过滤性能测试,结果表明纺丝时间为7 h时,纤维膜具有较好的性能,其弹性模量为48.15 MPa、断裂伸长率183.30%、拉伸断裂应力2.11 MPa、拉伸强度2.49 MPa、拉伸屈服应力1.23 MPa、最大力1.38 N,阻气值为3.99 k Pa·S/m,过滤效率为99.55%,压降为621.32 Pa.吸附银离子实验表明,最佳GA交联浴配比为GA(vol%)=3.5%.紫外可见光谱(UV)及透射电镜(TEM)表征证明,有10 nm左右纳米银生成.抑菌实验表明,载银PET/CTS复合纳米纤维膜对金黄色葡萄球菌(S.a.)和大肠杆菌(E.coli.)的杀菌率分别为99.97%和99.99%.     

ATRP法在纳米SiO2表面接枝PBA及其对POM的改性

本论文研究了原子转移自由基聚合法(ATRP)在纳米二氧化硅(SiO2)表面接枝聚丙烯酸丁酯(PBA)以及其对聚甲醛（POM）进行改性。红外光谱（FTIR）、透射电镜(TEM)及凝胶渗透色谱（GPC）等测试表明：采用ATRP法可制备均匀分散的SiO2-g-PBA纳米复合粒子。力学性能、扫描电子显微镜（SEM）及透射电子显微镜（TEM）等测试表明：纳米SiO2在POM中团聚明显,而SiO2-g-PBA纳米复合粒子POM中分散均匀,导致POM/SiO2-g-PBA纳米复合材料的缺口冲击强度明显高于POM及POM/SiO复合材料,当SiO2-g-PBA纳米复合粒子的质量分数为2%时,POM/SiO2-g-PBA复合材料的冲击强度是POM的8倍多,同时拉伸强度有一定的增加。     

具有抗菌性能的载药复合微纳米纤维的制备及其结构和性能表征

利用静电纺丝技术制备了一种具有抗菌性能的氧化锌(ZnO)/聚乳酸(PLA)/聚己内酯(PCL)载药微纳米纤维膜,并通过扫描电子显微镜(SEM)、X射线衍射(XRD)和傅里叶变换红外光谱(FTIR)分别对复合膜的表面形态、元素组成和化学结构进行表征。通过抗菌实验评价了复合膜的抗菌性能,用紫外分光光度计测试复合膜在体外的药物释放行为。结果显示,以物理共混的方式将ZnO和氢溴酸高乌甲素(LAH)成功载入复合微纳米纤维;与PLA/PCL复合微纳米纤维膜相比,ZnO/PLA/PCL复合微纳米纤维膜表现出更好的抗菌效率。当ZnO含量为10%(wt)时,复合微纳米纤维膜具有最佳的抗菌性能;药物释放性能结果表明,ZnO/PLA/PCL复合微纳米纤维膜具有良好的药物缓释性能。     

AOPAN@PAN同轴纳米纤维的制备及吸附性能

将盐酸羟胺与聚丙烯腈(PAN)反应得到偕胺肟化聚丙烯腈(AOPAN)溶液,随后采用同轴静电纺丝技术,制备了以AOPAN为壳,PAN为芯的同轴纳米纤维(AOPAN@PAN).通过透射电子显微镜(TEM)、扫描电子显微镜(SEM)和红外光谱(FTIR)等对纤维的形貌、组成和力学性能进行了表征.结果表明,随着PAN用量的增加,AOPAN@PAN同轴纳米纤维的强度逐渐变大,当芯层与壳层质量比为1∶3时,纳米纤维的抗拉伸强度和断裂伸长率分别为3.677 MPa和18.03%;对Cu~(2+),Pb~(2+),CrO_4~(2-)和甲基橙(MO)的最大吸附量分别为135.1,151.2,120.48和43.45 mg/g;使水中Cu~(2+),Pb~(2+),CrO_4~(2-)和MO的浓度分别降低到0.17,0.03,0.06和0.91 mg/L.     

Ag/ZnO纳米纤维的制备及光催化性能

采用静电纺丝技术及煅烧法制备了氧化锌纳米纤维, 然后采用水热法将银纳米颗粒负载到了氧化锌纳米纤维表面. 利用X射线衍射(XRD)、 X射线光电子能谱(XPS)、 能量色散X射线光谱(EDX)、 扫描电子显微镜(SEM)及透射电子显微镜(TEM)等技术对合成的Ag/ZnO纳米纤维的结构和组成进行了表征. SEM结果表明, 直径在5~100 nm之间的银纳米颗粒附着在直径在80~330 nm之间的氧化锌纤维表面形成了异质结构. 以常见的有机污染物甲基橙、 亚甲基蓝和罗丹明B等为降解底物, 对Ag/ZnO纳米纤维的光催化性能进行了表征. 结果表明, 负载银纳米颗粒后, 复合催化剂的光催化性能明显提高.     

离子液体中纤维素/纳米层状ZnO复合抗菌纤维的制备及性能

以表面活性剂十二烷基磺酸钠(SDS)为模板,Zn(NO_3)_2·6H_2O和NaOH为锌源和沉淀剂,通过改进的模板法在温和条件下制得纳米层状ZnO.以离子液体1-烯丙基-3-甲基咪唑氯盐([Amim]Cl)为溶剂,木浆纤维素和纳米层状ZnO为原料,采用溶液共混方法,通过干湿法纺丝制备了ZnO质量分数分别为3%,5%,7%及9%的纤维素/ZnO纳米复合纤维.采用X射线衍射(XRD)、X射线光电子能谱(XPS)、透射电子显微镜(TEM)、场发射扫描电子显微镜(SEM)及热重分析(TG)等方法对纳米层状ZnO及纤维素/ZnO复合纤维进行了表征,并探讨了ZnO的加入对复合体系流变性的影响,同时对复合纤维进行了力学和抗菌性能测试.研究结果表明,所制备氧化锌纯度高,且呈现出重复周期为3.58 nm的层状结构,抗菌性能优异.纳米层状ZnO的加入提高了纤维素纤维的热稳定性和机械强度,同时赋予纤维对金黄色葡萄球菌和大肠杆菌的抑菌性.ZnO片层被纤维素链剥离,并均匀分散于纤维素/ZnO复合物中.ZnO的加入增大了纤维素溶液的黏度,当ZnO含量达到5%以上时,在整个频率范围内,弹性模量大于损耗模量,纳米粒子可稳定悬浮.     

Ag/ZnO纳米纤维的制备及光催化性能（英文）

采用静电纺丝技术及煅烧法制备了氧化锌纳米纤维,然后采用水热法将银纳米颗粒负载到了氧化锌纳米纤维表面.利用X射线衍射(XRD)、X射线光电子能谱(XPS)、能量色散X射线光谱(EDX)、扫描电子显微镜(SEM)及透射电子显微镜(TEM)等技术对合成的Ag/ZnO纳米纤维的结构和组成进行了表征.SEM结果表明,直径在5~100 nm之间的银纳米颗粒附着在直径在80~330 nm之间的氧化锌纤维表面形成了异质结构.以常见的有机污染物甲基橙、亚甲基蓝和罗丹明B等为降解底物,对Ag/ZnO纳米纤维的光催化性能进行了表征.结果表明,负载银纳米颗粒后,复合催化剂的光催化性能明显提高.     

p-CuO/n-In_2O_3异质结纳米纤维的制备及气敏特性

以电纺In_2O_3纳米纤维为模版,通过溶剂热法构建了p-CuO/n-In_2O_3异质结纳米纤维.采用扫描电子显微镜(SEM)、透射电子显微镜(TEM)、X射线衍射(XRD)和X射线光电子能谱(XPS)等方法对所得材料的形貌和结构进行表征.结果表明,CuO纳米颗粒可以均匀地负载在超细In_2O_3纳米纤维表面;随着反应液中乙酸铜浓度的增加,负载的CuO纳米颗粒密度也逐渐增加.通过制备旁热式气敏器件对复合纳米纤维材料的气敏特性进行了研究.结果表明,与纯In_2O_3纳米纤维相比,p-CuO/n-In_2O_3异质结纳米纤维对H_2S气体具有较高的灵敏度和较低的工作温度.     

SnO2/TiO2复合纳米纤维的制备及光催化性能

采用静电纺丝技术,以聚乙烯吡咯烷酮和钛酸正丁酯为前驱体,制得锐钛矿相TiO2纳米纤维。以TiO2纳米纤维为模板,通过水热合成法,制备了具有异质结构的SnO2/TiO2复合纳米纤维。利用扫描电镜(SEM)、X射线能量色散光谱（EDS）、透射电镜(TEM)和X射线衍射(XRD)等分析测试手段对其形貌和结构进行了表征,结果表明,SnO2纳米粒子均匀地生长在TiO2纳米纤维表面,形成了异质结构的SnO2/TiO2复合纳米纤维材料。通过改变反应物浓度,能有效地实现SnO2/TiO2复合纳米纤维的可控合成。以罗丹明B为模拟污染物,考察了SnO2/TiO2复合纳米纤维的光催化性能,与纯TiO2纳米纤维相比光催化活性明显提高,初步探讨了光催化反应机理。     

Electrospun poly(l-lactide)-grafted hydroxyapatite/poly(l-lactide) nanocomposite fibers

Composite fibers composed of poly(l-lactide)-grafted hydroxyapatite (PLA-g-HAP) nanoparticles and polylactide (PLA) matrix were prepared by electro-spinning. Environmental scanning electron microscope (ESEM) and transmission electron microscopy (TEM) were employed to investigate the morphology of the composite fibers and the distribution of PLA-g-HAP nanoparticles in the fibers, respectively. At a low content (∼4 wt%) of PLA-g-HAP, the nanoparticles dispersed uniformly in the fibers and the composite fibrous mats exhibited higher strength properties, compared with the pristine PLA fiber mats and the simple hydroxyapatite/PLA blend fiber mats. But when the content of PLA-g-HAP further increased, the nanoparticles began to aggregate, which resulted in the deterioration of the mechanical properties of the composite fiber mats. The degradation behaviors of the composite fiber mats were closely related to the content of PLA-g-HAP. At a low PLA-g-HAP content, degradation may be delayed due to the reduction of autocatalytic degradation of PLA. When PLA-g-HAP content was high, degradation rate increased because of the enhanced wettability of the composite fibers and the escape of the nanoparticles from fiber surfaces during incubation.     

Effects of polylactic acid and rPET minor components on phase evolution,tensile and thermal properties of polyethylene‐based composite fibers

High mechanical performance and partially biodegradable PE‐composite fibers modified with polylactic acid (PLA) and recycled polyethylene terephthalate (rPET) minor components were prepared using melt extrusion and hot drawing process. Rheological properties, morphology, tensile, and thermal properties were investigated. All blends exhibited shear thinning behavior except for starting PLA and rPET. PLA and rPET dispersed phases appeared as droplets in as‐extruded strand, and PLA droplets were mostly larger than those of rPET. The fibrillation of both PLA and rPET domains was achieved after further hot drawing as the fiber. The morphology and tensile properties of the fibers mainly depended on the types and contents of dispersed phases including draw ratios. The ultimate strength of the polymer fibers at draw ratio of 20 was more than 600 times higher than that of the as‐spun sample of the same composition. Remarkable improvement in secant modulus and ultimate strength was found for PE‐30PLA, but the drawing process of this composition encountered some difficulties and rough surface of the fiber was observed. The stiffness and tensile stress for PE‐10PLA‐10rPET fiber were clearly improved when compared with PE and PE‐10PLA. A decrease in thermal stability of PE/PLA composites was observed with increasing PLA content whereas additional presence of rPET significantly increased the stability of the composites both in nitrogen and in air. PE/PLA/rPET fiber possessing high stiffness with good thermal stability prepared in this work has high potential for being utilized as structural parts for load‐bearing applications.     

电纺聚氧化乙烯纤维的分散形态和结晶行为研究

将聚氧化乙烯(PEO)水溶液在不同的工艺条件下进行电纺,制备了PEO纤维.用SEM研究了纤维的分散形态;用DSC和XRD研究了纤维的结晶性能.电纺纤维分散形态是由浓度、电压、固化距离等因素综合作用的结果.其中,浓度是最关键的因素.降低溶液浓度,提高静电压和增加固化距离均会使纤维变细.电纺得到的纤维与原粉相比,电纺使纤维结晶度下降,理论上分析了可能的机理.     

A feasible strategy to constructing hybrid conductive networks in PLA‐based composites modified by CNT‐d‐RGO particles and PEG for mechanical and electrical properties

Carbon nanotubes (CNTs) and reduced graphene oxide (RGO) were successfully assembled by chemical reaction to obtain CNT‐d‐RGO particles. Then, a home‐made dynamic impregnating device was used to prepare hybrid CNT‐d‐RGO/polyethylene glycol (PEG). Next, the different modifiers, including CNTs, GO, CNT‐d‐RGO, PEG, and CNT‐d‐RGO/PEG, were, respectively, added into poly‐(lactic acid) (PLA) matrix via melt‐compounding. The dispersed morphology for these different modifiers within the PLA matrix was confirmed by SEM and TEM observations. Especially, compared with the identical weight ratio of CNT‐d‐RGO, the hybrid CNT‐d‐RGO/PEG within the PLA matrix exhibited an excellent exfoliated and interconnected networks morphology. Moreover, compared with pure PLA, not only the crystallinity of all PLA‐based composites notably improved, but half‐crystallization time was also shortened. Furthermore, despite the addition of different modifiers, the crystal form of PLA‐based composites remained unchanged. Noticeably, compared with those of pure PLA, the tensile stress, strain, and modulus of PLA composite added with CNT‐d‐RGO/PEG increased by 29.4%, 4.1%, and 56.1%, respectively, and the V‐notch impact strength slightly improved. In addition, compared with pure PLA, volume resistivity of the PLA composite added with 1 wt% CNT‐d‐RGO/PEG decreased by 93.1%, and its volume conductivity increased by five orders of magnitude.     

Electrospun hyperbranched polylactic acid–modified cellulose nanocrystals/polylactic acid for shape memory membranes with high mechanical properties

The polylactic acid (PLA) nanofiber membranes reinforced with hyperbranched PLA‐modified cellulose nanocrystals (H‐PLA‐CNCs) were prepared by electrospinning. The H‐PLA‐CNCs and the nanofiber membranes were researched by Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), thermal gravimetric analysis (TGA), differential scanning calorimetry (DSC), and dynamic mechanical analysis (DMA). The outcomes embodied that the cellulose nanocrystals (CNCs) could be successfully improved by the hyperbranched PLA, which would offer powerful CNCs/matrix interfacial adhesion. Thus, the mechanical and shape memory properties of PLA can be improved by adding the H‐PLA‐CNCs. In particular, when the addition of H‐PLA‐CNCs was 7 wt%, the tensile strength and an ultimate strain of PLA composite nanofiber membranes was 15.56 MPa and 25%, which was 228% and 72.4% higher than that of neat PLA, respectively. In addition, the shape recovery rate of the PLA/5 wt% H‐PLA‐CNCs composite nanofiber membrane was 93%, which was 37% higher than that of neat PLA. We expected that this present study would provide unremitting efforts for the development of more effective approaches to prepare biology basic shape memory membranes with high mechanical properties.     

静电纺丝法制备铁酸锌中空纤维及其磁学性能

以锌盐、铁盐和聚乙烯吡咯烷酮(PVP)为原料,通过静电纺丝法先制备PVP/硝酸盐复合纤维,这些复合纤维以5℃·min-1的升温速率加热到500℃并保温3h,最终得到铁酸锌(ZnFe2O4)中空纤维.通过X射线衍射(XRD)、扫描电镜(SEM)、透射电镜(TEM)以及振动样品磁强计(VSM)等分析手段对中空纤维的晶体结构、形貌和磁学性能进行了研究.结果显示,ZnFe2O4中空纤维属于尖晶石结构,高温处理后仍能保持一维结构,纤维直径在200-400nm之间,纤维壁由大小为25nm的颗粒堆积而成.室温磁化结果显示制备的ZnFe2O4中空纤维具有超顺磁性,在10kOe的磁化强度为2.03emu·g-1.     

聚乳酸/氧化锌柱撑皂石纳米复合材料制备与性能及结构表征

通过微波水解法制备了ZnO柱撑皂石,并以其为加工助剂制备了聚乳酸(PLA)/ZnO柱撑皂石纳米复合材料.通过X射线衍射(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)、对ZnO柱撑皂石及PLA/ZnO柱撑皂石纳米复合材料的结构进行了表征,并对其力学性能和热稳定性能进行了测试.微观结构分析表明,ZnO柱撑皂石呈现剥离状,并均匀分散在PLA基质中.力学性能研究表明0.3%ZnO柱撑皂石的加入有助于改善PLA复合材料的断裂伸长率.SEM分析表明PLA复合材料的断面发生明显改变,表现良好韧性;DSC结果显示纳米ZnO柱撑皂石可以降低复合材料的玻璃化转变温度、结晶温度,有助于提高PLA复合材料的结晶度,与XRD分析相吻合;热重分析表明ZnO柱撑皂石可以提高PLA复合材料的热稳定性.测试结果表明,ZnO柱撑皂石在PLA基质中起到了异相成核的作用,促进了PLA基质的结晶.     

Enhanced orientation of PEO polymer chains induced by nanoclays in electrospun PEO/clay composite nanofibers

Polymer fibers composed of poly(ethylene oxide) (PEO) and nanoclay were fabricated by electrospinning. The morphology of the composite nanofibers was characterized by scanning electron microscope (SEM) and transmission electron microscope (TEM), which showed aligned nanoclays in the fibers. Polarized Fourier transform infrared (FT-IR) spectroscopy revealed that the PEO chains in the composite fibers exhibit a higher degree of orientation than that in PEO nanofibers containing no nanoclay. It is believed that spatial confinement is present in the electrospun nanofibers, which results in the enforcement of the mutual restriction. The anisotropic hierarchical nanostructure may have potential applications in optics, mechanical materials, and biomedical materials for cell culture.     

Electrospinning and characterization of poly(vinyl alcohol)/chitosan oligosaccharide/clay nanocomposite nanofibers in aqueous solutions

Submicron fibers of the composite of poly(vinyl alcohol) (PVA), chitosan oligosaccharide [COS, (1→4)2-amino-2-deoxy-β-d-glucose], and montmorillonite clay (MMT) were prepared using electrospinning method with aqueous solutions. Scanning electron microscopy, transmission electron microscopy (TEM), X-ray diffraction (XRD), thermal gravimetric analyzer, and tensile strength testing machine (Zwick) were utilized to characterize the PVA/COS/MMT nanofiber mats morphology and properties. The PVA/COS ratio and MMT concentration play important roles in nanofiber mat properties. XRD and TEM data demonstrated that exfoliated MMT layers were well-distributed within nanofiber. It was also found that the mechanical property and thermal stability were increased with COS and MMT contents.