具有抗菌性能的载药复合微纳米纤维的制备及其结构和性能表征

利用静电纺丝技术制备了一种具有抗菌性能的氧化锌(ZnO)/聚乳酸(PLA)/聚己内酯(PCL)载药微纳米纤维膜,并通过扫描电子显微镜(SEM)、X射线衍射(XRD)和傅里叶变换红外光谱(FTIR)分别对复合膜的表面形态、元素组成和化学结构进行表征。通过抗菌实验评价了复合膜的抗菌性能,用紫外分光光度计测试复合膜在体外的药物释放行为。结果显示,以物理共混的方式将ZnO和氢溴酸高乌甲素(LAH)成功载入复合微纳米纤维;与PLA/PCL复合微纳米纤维膜相比,ZnO/PLA/PCL复合微纳米纤维膜表现出更好的抗菌效率。当ZnO含量为10%(wt)时,复合微纳米纤维膜具有最佳的抗菌性能;药物释放性能结果表明,ZnO/PLA/PCL复合微纳米纤维膜具有良好的药物缓释性能。     

Ag+/Ag/ZnO多孔纳米结构纤维材料的制备及可见光催化性能

借助棉花纤维模板, 采用两步法制备了Ag⁺/Ag/ZnO多孔纳米结构纤维材料, 并利用X射线衍射(XRD)、 X射线光电子能谱(XPS)、 扫描电子显微镜(SEM)和紫外-可见光谱(UV-Vis)等对其进行了表征. 以亚甲基蓝(MB)的脱色降解为模型反应, 考察了银修饰量(摩尔分数, 0~1.50%)对ZnO纳米结构纤维材料光催化性能的影响. 结果表明, 利用模板辅助的两步法制备了Ag⁺-Ag共修饰的ZnO多孔纳米结构纤维材料Ag⁺/Ag/ZnO, Ag⁺和Ag通过改变ZnO的晶胞结构、 光吸收特性及形貌等影响其光催化性能; 在可见光条件下, Ag⁺/Ag/ZnO的催化性能优于纯ZnO, 且与修饰量有关.     

ZnO纳米纤维的静电纺丝及其光催化性能的研究

以聚乙烯醇溶液为络合剂与醋酸锌反应制得前驱体溶液,采用静电纺丝法制备PVA/Zn(Ac)2复合纳米纤维,经过高温煅烧得到直径为100 nm的ZnO纳米纤维,采用差热-热重分析、红外光谱分析、X射线粉末衍射分析及扫描电镜等手段对其进行了表征.光催化降解酸性品红溶液的实验结果表明,太阳光照65 min使质量浓度为45 mg/L酸性品红水溶液的脱色率达93%;另外,重复使用ZnO纳米纤维4次之后,其光催化降解率仍能达到70%以上.这充分说明ZnO纳米纤维具有良好的光催化性能.     

Ag/ZnO纳米纤维的制备及光催化性能

采用静电纺丝技术及煅烧法制备了氧化锌纳米纤维, 然后采用水热法将银纳米颗粒负载到了氧化锌纳米纤维表面. 利用X射线衍射(XRD)、 X射线光电子能谱(XPS)、 能量色散X射线光谱(EDX)、 扫描电子显微镜(SEM)及透射电子显微镜(TEM)等技术对合成的Ag/ZnO纳米纤维的结构和组成进行了表征. SEM结果表明, 直径在5~100 nm之间的银纳米颗粒附着在直径在80~330 nm之间的氧化锌纤维表面形成了异质结构. 以常见的有机污染物甲基橙、 亚甲基蓝和罗丹明B等为降解底物, 对Ag/ZnO纳米纤维的光催化性能进行了表征. 结果表明, 负载银纳米颗粒后, 复合催化剂的光催化性能明显提高.     

同轴静电纺丝法制备ZnO/Ag2O纳米纤维材料及其光电催化性能研究

以醋酸锌和乙酰丙酮银为前驱体, 通过同轴静电纺丝和热处理过程在氟掺杂氧化锡(FTO)导电玻璃上制备了ZnO/Ag₂O同轴纳米纤维. 采用X射线衍射(XRD)、 X射线光电子能谱(XPS)、 扫描电子显微镜(SEM)、 透射电子显微镜(TEM)、 拉曼光谱和紫外-可见漫反射光谱(UV-Vis DRS)等手段对材料进行了表征. 以氙灯模拟可见光光源, 亚甲基蓝为目标降解物, 考察了所制备纳米纤维的光电催化活性. 结果表明, 同轴ZnO/Ag₂O纳米纤维具有壳核类似结构(ZnO为壳, Ag₂O为核), Ag₂O与ZnO形成的异质结和杂质能级降低了ZnO的带隙能, 提高了对可见光的利用率. 在可见光下, 与纯ZnO相比, ZnO/Ag₂O具有很强的光电催化能力, 并且Ag₂O的量对同轴纤维光电催化活性影响很大, 在同样光电催化条件下, ZnO/Ag₂O-7同轴纳米纤维的光电催化效果最好, 亚甲基蓝降解率达93%, 动力学常数最大为1.13×10 ^-2 min ^-1.     

Y掺杂的ZnO纳米纤维材料的制备及其气敏传感器作用机理

采用静电纺丝法成功制备了Y掺杂的ZnO纳米纤维.并通过X射线衍射(XRD),扫描电子显微镜(SEM),能量色散X射线(EDX),透射电子显微镜(TEM)以及热重差热分析(TG-DTA)等手段对样品的结构和形貌进行了表征分析.同时用纯的ZnO和Y掺杂的ZnO纳米纤维制备了传感器,对浓度为(1-200)×10^-6 (体积分数)丙酮的气敏特性进行了测试分析.测试结果表明,可以通过简单控制纳米纤维中Y的含量,来微调该传感器的气敏特性.同时也发现通过Y掺杂, ZnO纳米纤维对丙酮的气敏特性有所改善,表现出很高的响应.纯ZnO和Y掺杂ZnO制成的传感器对几种潜在干扰气体表现出良好的选择性,比如氨气、苯、甲醛、甲苯以及甲醇.本文最后也讨论了该传感器的气敏作用机理.     

Ag/ZnO纳米纤维的制备及光催化性能（英文）

采用静电纺丝技术及煅烧法制备了氧化锌纳米纤维,然后采用水热法将银纳米颗粒负载到了氧化锌纳米纤维表面.利用X射线衍射(XRD)、X射线光电子能谱(XPS)、能量色散X射线光谱(EDX)、扫描电子显微镜(SEM)及透射电子显微镜(TEM)等技术对合成的Ag/ZnO纳米纤维的结构和组成进行了表征.SEM结果表明,直径在5~100 nm之间的银纳米颗粒附着在直径在80~330 nm之间的氧化锌纤维表面形成了异质结构.以常见的有机污染物甲基橙、亚甲基蓝和罗丹明B等为降解底物,对Ag/ZnO纳米纤维的光催化性能进行了表征.结果表明,负载银纳米颗粒后,复合催化剂的光催化性能明显提高.     

不同形貌ZnO纳米结构的电子显微分析

控制实验合成条件,利用溶胶-凝胶法和化学溶液生长法制备出不同形貌的ZnO纳米结构。采用X射线衍射仪(XRD)、扫描电子显微镜( SEM) 以及透射电子显微镜(TEM)等多种测试手段对ZnO纳米结构的微观形态及晶相进行了分析。结果表明:3种ZnO纳米结构形貌虽不同,但均具有Z nO六方纤锌矿晶相结构。ZnO纳米棒和花状ZnO纳米结构为单晶,生长方向均沿(0001)方向。ZnO纳米球则为多晶。     

低压近场静电纺丝ZnO/PVDF复合微米纤维阵列的制备及压力传感性

利用低压近场静电纺丝技术制备了ZnO/PVDF(聚二偏氟乙烯)微米纤维平行阵列, 通过光学显微镜、扫描电子显微镜(SEM)和X射线能量色散光谱(EDS)对ZnO/PVDF微米纤维进行了表征. 该复合纤维的平均直径约为40 μm. EDS分析测试证明ZnO纳米颗粒已经掺杂进入了平行微米纤维中. 压电性能和电学性能测试结果表明, ZnO/PVDF微米纤维阵列的压电性能增强. 研究结果表明, 近场电纺丝ZnO/PVDF复合微米纤维阵列在压电型压力传感器和纳米发电机领域具有潜在的应用价值.     

低压近场静电纺丝ZnO/PVDF复合微米纤维阵列的制备及压力传感性（英文）

利用低压近场静电纺丝技术制备了ZnO/PVDF(聚二偏氟乙烯)微米纤维平行阵列,通过光学显微镜、扫描电子显微镜(SEM)和X射线能量色散光谱(EDS)对ZnO/PVDF微米纤维进行了表征.该复合纤维的平均直径约为40μm.EDS分析测试证明ZnO纳米颗粒已经掺杂进入了平行微米纤维中.压电性能和电学性能测试结果表明,ZnO/PVDF微米纤维阵列的压电性能增强.研究结果表明,近场电纺丝ZnO/PVDF复合微米纤维阵列在压电型压力传感器和纳米发电机领域具有潜在的应用价值.     

Preparation and characterization of biodegradable sugarcane bagasse nano reinforcement for polymer composites using ball milling operation

The present work includes the processing and characterization of nano-based natural reinforcement for polymer composite materials. Sugarcane bagasse has been collected and the fibers were extracted using manual striping process. Undesirable materials present in the extracted fibers were removed by 1% NaOH-based chemical treatment. The macrofibers were reduced to nano scale by using high-energy ball milling process. Nanoparticles from bagasse fibers were characterized by X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy (SEM), and thermogravimetric analysis (TGA). The degree of crystallinity of nano bagasse is 55.2% and it was reported by using XRD. A FTIR spectrum confirms the presence of cellulose functional groups in nano bagasse. The nano bagasse dimensions and morphology were investigated using SEM. The average length and diameter of the nano bagasse is 51.2 and 46.1 nm, respectively. Thermal stability of the nano bagasse was revealed by TGA analysis. The chemical composition of cellulose, lignin, and hemicellulose contents was also investigated.     

Preparation and characterization of cellulose-ZnO nanocomposite based on ionic liquid ([C4mim]Cl)

Cellulose-ZnO composite was achieved by microwave assisted dissolution of cellulose in ionic liquid 1-butyl-3-methylimidazolium chloride ([C₄mim]Cl) followed by addition of premixed ground of Zn(CH₃COO)₂·2H₂O and NaOH. Surface characterization, optical property and thermal stability of nanocomposite were determined by X-ray diffraction, scanning electron microscopy (SEM), UV–Vis spectroscopy and thermo gravimetric analysis. XRD patterns showed the ZnO in polymer matrix has the wurtzite structure. Presence of zinc oxide nanoparticles and cellulose fibers in the composites were observed by SEM. Band-edge transition of zinc oxide in the nanocomposite occurs in lower wavelength than bulk zinc oxide. Thermal stability of nanocomposite was lower than regenerated cellulose due to catalyst behavior of zinc oxide nanoparticles in cellulose matrix.     

介孔TiO2-ZnO复合薄膜的制备与表征

以三嵌段聚合物P123为模板剂, 以钛酸异丙酯和二水乙酸锌为无机前驱体, 利用溶胶-凝胶法和旋涂法成功地制备了不同ZnO含量的介孔TiO2-ZnO复合薄膜. 在ZnO前驱体摩尔分数为0~50％范围内获得薄膜质量较高的介孔TiO2-ZnO复合薄膜. 用小角XRD、扫描电子显微镜(SEM)、高分辨透射电子显微镜(HRTEM)、能谱仪(EDS)、紫外-可见吸收光谱(UV-Vis)及X射线光电子能谱(XPS)对所得的复合薄膜进行了表征和分析. EDS和XPS等研究证明介孔薄膜为TiO2和ZnO的复合体系, 且ZnO前驱体含量的增加仍能保持TiO2-ZnO复合薄膜的均匀性. UV-Vis研究结果表明, 介孔复合薄膜的光学带隙宽度为3.45-3.58 eV, 随着ZnO含量的增加, 复合薄膜的紫外吸收蓝移.     

Zn基片上ZnO及ZnS/ZnO复合纳米阵列的液相合成及发光性质

采用温和的溶液路线在Zn基片上合成了单晶态的ZnO纳米棒阵列、 纳米片阵列和ZnS/ZnO复合双层纳米棒阵列. 使用X射线粉末衍射仪、 扫描电子显微镜、 高分辨透射电子显微镜、 X射线光电子能谱仪等对产物的组成、 结构及形貌进行了表征. 讨论了表面活性剂在液相合成中对产物形貌的调控作用. 通过室温发射光谱的测定, 研究了所得纳米阵列材料的发光性质.     

Preparation and Gas Sensing Performance of Hierarchical Porous ZnO-based Materials with Sunflower Rods as a Biological Template

A graded porous structure SnO2/ZnO composite was prepared with sunflower rods as a biological template. The prepared samples were subjected to phase analysis by scanning electron microscopy(SEM), transmission electron microscopy(TEM), X-ray diffractiometry(XRD) and X-ray photoelectron spectroscopy(XPS).ZnO sample was a pure phase of hexagonal wurtzite, and the template had been completely removed. The surface of the sample presented a honeycomb-like structure of a sunflower rod template, which was formed by interconnecting the porous channels, and had a smaller average size and exhibited n-n heterojunction at tlie n-type ZnO interface. Compared with that of pure ZnO, the response of the hierarchical porous structure SnO2/ZnO composite to 100 mg/L w-butanol reached a maximiuTi of 40.61 at 240℃, about 2.7 times higher than that of pure ZnO. Its response time and recovery time are 6 and 3 s, respectively, which are also better than those of pure ZnO. SnO2/ZnO composite exhibits good gas selectivity, which is related to the improvement of the structure and the forming of n-n heterojunctions of the material.     

纳米TiO_2-ZnO二元负载木材的制备及性质

采用两步法将TiO_2/ZnO纳米材料与杨木试样复合,制备了纳米二元负载木材.通过X射线衍射(XRD)、傅里叶变换红外光谱(FTIR)和扫描电子显微镜(SEM)对样品的结构和形貌进行了表征,并探讨了不同处理条件下得到的纳米氧化物负载木材及非纳米氧化物负载木材的抗菌性和耐候性.结果表明,氧化锌和二氧化钛二元协同负载木材的抗菌性和耐候性均优于单一纳米晶处理的木材;在溶剂热反应中以正己烷作为溶剂所制备样品的性能优于以水和无水乙醇为溶剂制备的样品;并且纳米结构负载木材的抗菌性和耐候性优于非纳米结构负载的木材.     

Jute stick extract assisted hydrothermal synthesis of zinc oxide nanoflakes and their enhanced photocatalytic and antibacterial efficacy

In this paper, we used green and hydrothermal methodology to prepare zinc oxide (ZnO) nanoflakes (NFs) with jute stick extract (J–ZnO NFs) as growth substrate. The prepared materials were characterized using different analytical techniques including ultraviolet–visible spectroscopy (UV–vis), X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), thermogravimetric analysis (TGA), fourier transform infrared (FTIR) spectroscopy, and X-ray photoelectron spectroscopy (XPS). The characteristic absorption peak for ZnO NFs and J–ZnO NFs were observed from the UV–vis spectrum at 373 and 368 nm respectively. The hexagonal wurtzite crystal structure of ZnO NFs and J–ZnO NFs was confirmed by XRD analysis. FESEM and TEM analyses of synthesized J–ZnO NFs confirmed their NFs shape and collectively flower-like structure formation by the assembly of NFs of J–ZnO on cellulose of jute stick extract substrate. The FTIR analysis revealed the functional groups of jute stick extract biomolecules, mainly cellulose, are responsible for the formation of collectivel flower like J–ZnO NFs structure. The XPS analysis revealed the surface and chemical compositions (Zn, C, and O) of J–ZnO NFs. The photocatalytic performance of ZnO NFs and J–ZnO NFs samples was carried out by the degradation of methylene blue (MB) dye solution under UV light irradiation. The degradation efficiency of ZnO NFs and J–ZnO NFs was obtained 79 % and 89 %, respectively, for 5 h. Notably, the degradation efficiency of the J–ZnO NFs was 98 % after 8 h of irradiation, which is very inspiring. The both NFs exhibited first-order kinetics with MB photodegradation. We also examined the possible antibacterial activity of both samples against Escherichia coli (E. coli) pathogens, which demonstrated a significant result with a 17 mm and 19 mm zone of inhibition by ZnO NFs and J–ZnO NFs respectively.     

Facile Fabrication of Porous ZnS and ZnO Films by Coaxial Electrospinning for Highly Efficient Photodegradation of Organic Dyes

Porous ZnS and ZnO nano‐crystal films were fabricated via a three‐step procedure. First, Zn(CH₃COO)₂/Silk Fibroin nanofiber mats were prepared by coaxial electrospinning. Second, Zn(CH₃COO)₂/Silk Fibroin mats were immersed in NaS solution to react with S²⁻ to obtain ZnS/Silk Fibroin nanofiber mats. Finally, ZnO porous films were prepared by calcination of ZnS/Silk Fibroin composite mat at 600°C in air atmosphere. When ZnS/Silk Fibroin mats were calcinated in nitrogen, ZnS/Carbon composite mats were obtained accordingly. The resulting porous films were fully characterized. The ZnO porous films were the aggregation of ZnO nano‐crystal with hexagonal wurtzite structure. The seize of ZnO was estimated in the range of 10–20 nm. Both of the ZnS and ZnO nano‐crystal films exhibited high photocatalytic activities for the photodegradation of Methylene blue and Rhodamine B. It was also found that ZnO porous films are better than ZnS/Carbon nanofiber mats. In addition, photocatalysis of a real wastewater sample from a printing and dyeing company was conducted. The ZnO porous films exhibited excellent performance to treat the real samples. Moreover, the porous ZnO nano‐crystal photocatalyst could easily be recycled without notable loss of catalysis ability.     

Preparation,characterization and photocatalytic properties of BiOBr/ZnO composites

BiOBr/ZnO composite photocatalysts were prepared by a simple hydrothermal method. The as-prepared samples were characterized by X-ray diffraction(XRD), scanning electron microscopy(SEM), transmission electron microscopy(TEM), high-resolution transmission electron microscopy(HRTEM), UV–Vis diffusion reflectance spectroscopy(DRS) and photoluminescence(PL) spectroscopy, respectively. The photocatalytic activities were evaluated by the degradation of methyl blue(MB) under the simulated sunlight irradiation. Among all the samples, the BiOBr/ZnO composite with a mole ratio of 3:1(Bi:Zn) exhibited the best photocatalytic activity. The improvement of photocatalytic activity was mainly attributed to the low recombination ratio of photo-induced electron-hole pairs. The possible photocatalytic mechanism was discussed on the basis of the band structures of BiOBr and ZnO.