Biodegradable electrospun poly(l-lactide) fibers containing antibacterial silver nanoparticles

Biodegradable poly(l-lactide) (PLA) ultrafine fibers containing nanosilver particles were prepared via electrospinning. Morphology of the Ag/PLA fibers and distribution of the silver nanoparticles were characterized. The release of silver ions from the Ag/PLA fibers and their antibacterial activities were investigated. These fibers showed antibacterial activities (microorganism reduction) of 98.5% and 94.2% against Staphylococcus aureus and Escherichia coli, respectively, because of the presence of the silver nanoparticles.     

Plasticization of poly(lactide) with blends of tributyl citrate and low molecular weight poly(d,l-lactide)-b-poly(ethylene glycol) copolymers

Polylactide (PLA) is a potential candidate for the partial replacement of petrochemical polymers because it is biodegradable and produced from annually renewable resources. Characterized by its high tensile strength, unfortunately the brittleness and rigidity limit its applicability. For a great number of applications such as packaging, fibers, films, etc., it is of high interest to formulate new PLA grades with improved flexibility and better impact properties.In order to develop PLA-based biodegradable packaging, the physico-mechanical properties of commercially available PLA should be modified using biodegradable plasticizers. To this end, PLA was melt-mixed with blends of tributyl citrate and more thermally stable low molecular weight block copolymers based on poly(d,l-lactide) and poly(ethylene glycol) of different molecular weights and topologies. The copolymers have been synthesized using a potassium based catalyst which is expected to be non toxic and were characterized by utilization of TGA, GPC and NMR techniques.The effect of the addition of up to 25 wt% plasticizer on the thermo-mechanical properties of PLA was investigated and the results were correlated with particular attention to the relationship between properties and applications.To confirm the safety of the catalyst used for the preparation of the copolymers, in vitro cytotoxicity tests have been carried out using MTS assay and the results show their biocompatibility in the presence of the fibroblast cells.Compost biodegradation experiments carried out using neat and plasticized PLA have shown that the presence of plasticizers accelerates the degradation of the PLA matrix.     

Poly l-lactide-layered double hydroxide nanocomposites via in situ polymerization of l-lactide

The use of clay nanofillers offers a potential route to improved barrier properties in polylactide films. Magnesium-aluminium layered double hydroxides (LDHs) are interesting in this respect and we therefore explored synthesis of PLA-LDH nanocomposites by ring-opening polymerization. This method is attractive because it should ensure good dispersion of LDH in the polymer. The effect of adding either LDH carbonate (LDH-CO₃) or laurate-modified LDH (LDH-C₁₂) was investigated. X-ray diffraction, scanning electron microscopy, and transmission electron microscopy revealed that exfoliated nanocomposites were obtained when using LDH-C₁₂ but that LDH-CO₃ gave a partly phase-separated morphology. Thermogravimetric analysis showed that PLA-LDH combinations exhibited higher degradation onset temperatures and differential scanning calorimetry confirmed that LDHs can act as nucleating agents. However, PLA molecular weight was significantly reduced when in-situ polymerization was conducted in the presence of the LDHs and we suggest that chain termination via LDH surface hydroxyl groups and/or metal-catalyzed degradation could be responsible.     

Synthesis and characterization of poly(l-lactic acid) reinforced by biomesogenic units

To increase the thermal and mechanical properties of poly(l-lactic acid) (PLA), a nontoxic biomesogen PFBH derived from ferulic acid (FA), 4-hydroxybenzoic acid (HBA) and 1,6-hexanediol (HD) was introduced into the PLA backbones by solution polymerization of PLA, PFBH and chain linker hexamethylene diisocyanate (HDI). The content of PFBH was varied from 0 to 30 mol% so that the effects of the biomesogen content on the thermal and physical properties, morphological textures and enzymatic degradation were examined, respectively. The synthesized materials were characterized by means of differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), wide angle X-ray diffraction (WAXD), polarizing light microscopy (PLM) and mechanical property measurements. It was found that introducing biomesogenic units could increase the thermal stability and reinforce the elastic properties, while reduced the melting temperature, the degree of crystallinity and the enzymatic degradation rate. The nontoxicity and biocompatibility of degradation would make the products promising candidates for medical applications in the area of tissue engineering.     

Phase behavior of biodegradable amphiphilic poly(l,l-lactide)-b-poly(ethylene glycol)-b-poly(l,l-lactide)

This study describes the miscibility phase behavior in two series of biodegradable triblock copolymers, poly(l-lactide)-block-poly(ethylene glycol)-block-poly(l-lactide) (PLLA-PEG-PLLA), prepared from two di-hydroxy-terminated PEG prepolymers (M_n = 4000 or 600 g mol⁻¹) with different lengths of poly(l-lactide) segments (polymerization degree, DP = 1.2-145.6). The prepared block copolymers presented wide range of molecular weights (800-25,000 g mol⁻¹) and compositions (16-80 wt.% of PEG). The copolymer multiphases coexistance and interaction were evaluated by DSC and TGA. The copolymers presented a dual stage thermal degradation and decreased thermal stability compared to PEG homopolymers. In addition, DSC analyses allowed the observation of multiphase separation; the melting temperature, T_m, of PLLA and PEG phases depended on the relative segment lengths and the only observed glass transition temperature (T_g) in copolymers indicated miscibility in the amorphous phase.     

Degradation behaviors of electrospun fibrous composites of hydroxyapatite and chemically modified poly(dl-lactide)

It is essential to individually tailor the biodegradability of electrospun fibers and their composites to meet the requirements of specific application. Electrospun poly(dl-lactide) (PDLLA) fibers grafted with functional groups were obtained to induce in situ mineralization of hydroxyapatite (HA), and HA/PDLLA composites were fabricated through hot-pressing of mineralized fibers after layer-by-layer deposition. The degradation behaviors during up to 1 year incubation were clarified for functionalized PDLLA fibers, mineralized HA/PDLLA fibers and hot-pressed composites. The carboxyl and amino groups of electrospun fibers indicated enhancement and alleviation of the autocatalysis effect on the polyester hydrolysis, respectively. The distribution of HA within fiber matrices led quick and strong water absorption, and caused neutralization of the weak acid environment and alleviation of the autocatalysis effect. Due to the location of mineralized HA on the surface of functionalized fibers, significant HA loss and preferential removal of amorphous and low-crystalline apatitic phase were determined during the degradation process. The hot-pressed composites indicated dense structure, small pore size and fusion on the fiber surface, leading significantly lower degradation rate than electrospun fibers and mineralized fibers. Higher degradation rate of matrix polymers and HA loss were shown for hot-pressed composites from mineralized fibers than those from blend electrospun HA/PDLLA fibers. The obtained results should provide solid basis for further applications of functionalized PDLLA fibers, mineralized fibers and fibrous composites in biomedical areas.     

Synthesis and characterization of novel elastomeric poly(D,L-lactide urethane) maleate composites for bone tissue engineering

Here, we report the synthesis and characterization of a novel 4-arm poly(lactic acid urethane)-maleate (4PLAUMA) elastomer and its composites with nano-hydroxyapatite (nHA) as potential weight-bearing composite. The 4PLAUMA/nHA ratios of the composites were 1:3, 2:5, 1:2 and 1:1. FTIR and NMR characterization showed urethane and maleate units integrated into the PLA matrix. Energy dispersion and Auger electron spectroscopy confirmed homogeneous distribution of nHA in the polymer matrix. Maximum moduli and strength of the composites of 4PLAUMA/nHA, respectively, are 1973.31 ± 298.53 MPa and 78.10 ± 3.82 MPa for compression, 3630.46 ± 528.32 MPa and 6.23 ± 1.44 MPa for tension, 1810.42 ± 86.10 MPa and 13.00 ± 0.72 for bending, and 282.46 ± 24.91 MPa and 5.20 ± 0.85 MPa for torsion. The maximum tensile strains of the polymer and composites are in the range of 5–93%, and their maximum torsional strains vary from 0.26 to 0.90. The composites exhibited very slow degradation rates in aqueous solution, from approximately 50% mass remaining for the pure polymer to 75% mass remaining for composites with high nHA contents, after a period of 8 weeks. Increase in ceramic content increased mechanical properties, but decreased maximum strain, degradation rate, and swelling of the composites. Human bone marrow stem cells and human endothelial cells adhered and proliferated on 4PLAUMA films and degradation products of the composites showed little-to-no toxicity. These results demonstrate that novel 4-arm poly(lactic acid urethane)-maleate (4PLAUMA) elastomer and its nHA composites may have potential applications in regenerative medicine.     

Thermal and electrical properties of poly(l-lactide)-graft-multiwalled carbon nanotube composites

The dispersion of the nanometer-sized carbon nanotubes in a polymer matrix leads to a marked improvement in the properties of the polymer. This approach can also be applied to biodegradable synthetic aliphatic polyesters such as poly(l-lactide) (PLLA), which has received a great deal of attention due to environmental concerns. In this study, PLLA was melt compounded with multiwalled carbon nanotubes (MWCNTs). A high degree of dispersion of the MWCNTs in the composites was obtained by grafting PLLA onto the MWCNTs (PLLA-g-MWCNTs). After oxidizing the MWCNTs by treating them with strong acids, they were reacted with l-lactide to produce the PLLA-g-MWCNTs. The morphology of the composite was observed with scanning electron microscopy. The mechanical properties of the PLLA/PLLA-g-MWCNT composite were higher than those of the PLLA/MWCNT composite. The thermal stability of the composites was studied using thermogravimetric analysis and their activation energy during thermal degradation was determined using the Kissinger and Flynn-Wall-Ozawa methods. The activation energy of PLLA/PLLA-g-MWCNT was higher than that of PLLA/MWCNT, which indicates that the composite made with the PLLA-g-MWCNTs was more thermally stable than the composite made with the MWCNTs.     

Characterization and release of triptolide-loaded poly (d,l-lactic acid) nanoparticles

Triptolide (TP), which has immunosuppressive effect, anti-neoplastic activity, anti-fertility function and severe toxicities on digestive, urogenital, blood circulatory system, was used as a model drug in this study. TP-loaded poly (d,l-lactic acid) (PLA) nanoparticles were prepared by the modified spontaneous emulsification solvent diffusion method (modified-SESD method). Dynamic light scattering system (DLS), transmission electron microscope (TEM), atomic force microscopy (AFM), differential scanning calorimetry (DSC), X-ray powder diffractometry and Fourier transform infra-red spectroscopy (FT-IR) were employed to characterize the nanoparticles fabricated for size and size distribution, surface morphology, the physical state of drug in nanoparticles, and the interaction between the drug and polymer. Encapsulation efficiency (EE) and the in vitro release of TP in nanoparticles were measured by the reverse phase high-performance liquid chromatography (RP-HPLC). The produced nanoparticles exhibited a narrow size distribution with a mean size of approximately 150 nm and polydispersity index of 0.088. The morphology of the nanoparticles exhibited a fine spherical shape with smooth surfaces without aggregation or adhesion. TP-entrapped in nanoparticles was found in the form of amorphous or semicrystalline. It was found that a weak interaction existed between the drug and polymer. In all experiments, more than 65% of EE were obtained. The in vitro release profile of TP from nanoparticles exhibited a typical biphasic release phenomenon, namely initial burst release and consequently sustained release. In this case, the particle size played an important role for the drug release. The modified-SESD method was a potential and advantage method to produce an ideal polymer nanoparticles for drug delivery system (DDS).     

Investigation of the degradation behaviour of poly(ethylene glycol-co-d,l-lactide) copolymer

The aim was to investigate the degradation behaviour of poly(ethylene glycol-co-d,l-lactide) (PEG-d,l-PLA) multiblock copolymer, in bulk and as microspheres, in aqueous medium. The degradation behaviour of PLA homopolymers in bulk and microspheres was evaluated as comparison.Microsphere preparation was performed by the double emulsion solvent evaporation method. Physical-chemical characterization of the raw polymers and the microspheres was performed by nuclear magnetic resonance (NMR) and modulated differential scanning calorimetry (MDSC). Polymer molecular weight, before and after incubation in aqueous environment, was evaluated by GPC; water uptake and mass loss were determined gravimetrically.The presence of PEG segments inside PLA chains gave a characteristic spongy structure to the microspheres. A significant increase in polymer T_g values was found for the microsphere formulations compared to polymer in bulk. After 63 days of incubation in the aqueous environment, the PEG-d,l-PLA microspheres achieved an average M_w reduction of 47% compared to 20% for PLA microspheres. The corresponding M_w decrease of the polymers in bulk was significantly higher: 72% and 41% for PEG-d,l-PLA and PLA, respectively.The data show how the degradation behaviour of polymer in bulk in an aqueous environment is significantly different from the behaviour of the corresponding microspheres. These results highlight the importance of performing a thorough physical-chemical characterization on microsphere formulations.     

Influence of hydrolytic degradation on the surface properties of poly-5d/95l-lactide resorbable bone plates

This study explores in vitro aging effects on the surface properties of resorbable PLA95 (poly-5d/95l-lactide) bone plates. The in vitro degradation of injection molded PLA95 bone plates was undertaken by soaking them in a PBS solution. Specimens were harvested at 0, 4, 6, 8, 12, 20, and 26 weeks. After each in vitro aging period, the surface morphology, viscosity, chemical structure, wettability, and thermal properties of the PLA95 bone plates were examined by scanning electron microscopy (SEM), capillary viscometers, attenuated total reflection fourier transform infrared spectroscopy (ATR-FTIR), contact angle, and modulated differential scanning calorimetry (MDSC), respectively. The surface morphology of aged PLA95 bone plates exhibited bulk erosion. As hydrolysis progressed, the inherent viscosity (I.V.) of the PLA95 plates gradually decreased from 0.83 ± 0.01 dL/g at week 0-0.46 ± 0.03 dL/g at week 26. However, the absorbance peak intensity ratio between δ_{as CH3} (A_1452 cm⁻¹) and ν_CO (A_1750 cm⁻¹) and the contact angle reveal different tendencies than that of molecular weight, which decreases. The contact angle of the PLA95 plates decreased until week 4, increased until week 8, and subsequently decreased again. Peak separation analysis reveals that the equilibrium part of the modulated DSC overlapped curves exhibit triple endothermic peaks. Over time, in vitro degradation changes the position and area of the individual peaks. After different time periods of degradation, the variation of wettability shows a tendency similar to the change of PLA95 plates crystallinity; the intensity ratio of A_1452 cm⁻¹ and A_1750 cm⁻¹ (δ_{as CH3}/ν _CO) absorbance peaks varied like the ratio of β/α-crystal heat of fusion. Results also show a similarity in the degradation time dependence in MDSC, contact angle, and ATR-FTIR measurements. During the in vitro aging process, the breakdown and subsequent recrystallization of PLA95 molecular chains might be attributed to a progressive change in wettability and the molecular conformation between δ_{as CH3} and ν_CO.     

Self-accelerated biodegradation of electrospun poly(ethylene glycol)-poly(l-lactide) membranes by loading proteinase K

Proteinase K was successfully loaded inside ultrafine fibers of poly(ethylene glycol)-poly(l-lactide) (PELA) by emulsion electrospinning. A core/shell fiber structure was formed and verified by a transmission electron microscope. In vitro biodegradation of electrospun PELA membranes containing proteinase K (PELA-P) was examined in Tris-HCl buffer solution at pH 8.6 and 37 °C in comparison with electrospun PELA membranes without proteinase K. During biodegradation, mass loss, water absorption, pH value of the incubated buffer, fibrous morphology and thermal properties were monitored. Results suggested that PELA-P membranes degraded significantly faster than PELA membranes. A significant drop in pH value of the buffer after incubation of PELA-P membranes for 1 d was observed, and after 7 d, PELA-P membranes lost their fibrous appearance and masses almost completely. In contrast, electrospun PELA membranes did not show any obvious changes. The obtained electrospun PELA-P membranes exhibited self-accelerated biodegradability and could benefit drug controlled release and tissue regeneration.     

Hydrolytic degradation behavior of poly(l-lactide)/SiO2 composites

In this work, different contents of nano-silica (SiO₂) particles were introduced into poly(l-lactide) (PLLA) to prepare PLLA/SiO₂ composites though a two-step compounding method, i.e. solution compounding (preparing master batch) and subsequent melt compounding (master batch dilution). The dispersion of SiO₂ was characterized using scanning electron microscope (SEM). The hydrophilicity of the material was evaluated by measuring the contact angle of water on the sample surface. The hydrolytic degradation measurements of the nanocomposites were carried out in alkaline solution at two different temperatures, i.e. 37 and 55 °C. Subsequently, microstructure evolution of PLLA matrix during the hydrolytic degradation process was systematically investigated using wide angle X-ray diffraction (WAXD), differential scanning calorimetry (DSC), and Fourier transform infrared spectroscopy (FTIR). The results showed that SiO₂ had good dispersion in the PLLA matrix. Largely enhanced hydrolytic degradation ability was achieved for PLLA/SiO₂ composites. Increasing the content of SiO₂ or enhancing the hydrolytic degradation temperature accelerated the hydrolytic degradation of PLLA matrix. Further results showed that SiO₂ promoted the reorganization of microstructure of PLLLA matrix during the hydrolytic degradation process.     

Surface properties and enzymatic degradation of end-capped poly(l-lactide)

Surface properties and enzymatic degradation of poly(l-lactide) (PLLA) end-capped with hydrophobic dodecyl and dodecanoyl groups were investigated by means of advancing contact angle (θ_a) measurement, quartz crystal microbalance (QCM) and atomic force microscopy (AFM). The θ_a values of end-capped PLLA films were larger than those of non-end-capped PLLA films, suggesting that the hydrophobic dodecyl and dodecanoyl groups were segregated on the film surface. The weight changes of end-capped PLLA thin films during enzymatic degradation in the presence of proteinase K were monitored by using a QCM technique. The relatively fast weight loss of PLLA film occurred during first few hours of degradation, followed by a decrease in the erosion rate. The erosion rate of PLLA films at the initial stage of degradation was dependent on the chain-end structure of PLLA molecules, and the value decreased with an increase in the amount of hydrophobic functional groups. The surface morphologies of PLLA thin films before and after degradation were characterized by AFM. After the enzymatic degradation, the surface of non-end-capped PLLA films was blemished homogeneously. In contrast, the end-capped PLLA thin films were degraded heterogeneously by the enzyme, and many hollows were formed on the film surface. From these results, it has been concluded that the introduction of hydrophobic functional groups at the chain-ends of PLLA molecules depressed the erosion rate at the initial stage of enzymatic degradation.     

Accelerated hydrolytic degradation of Poly(l-lactide)/Poly(d-lactide) stereocomplex up to late stage

Poly(l-lactide) (PLLA)/poly(d-lactide) (PDLA) blend specimens containing only stereocomplex as crystalline species, together with those of pure PLLA and PDLA specimens, were prepared by solution crystallization using acetonitrile as the solvent. Their accelerated hydrolytic degradation was carried out in phosphate-buffered solution at elevated temperatures of 70-97 °C up to the late stage. During hydrolytic degradation, the stereocomplex crystalline residues were first traced by gel permeation chromatography. Similar to the hydrolytic degradation of pure PLLA and PDLA specimens, the hydrolytic degradation of stereocomplexed PLLA/PDLA blend specimens slowed down at the late stage when most of the amorphous chains were removed and crystalline resides were formed and degraded. The estimated activation energy for hydrolytic degradation of stereocomplex crystalline residues (97.3 kJ mol⁻¹) is significantly higher than 75.2 kJ mol⁻¹ reported for α-form of PLLA crystalline residues. This indicates that the stereocomplex crystalline residues showed the higher hydrolysis resistance compared to that of α-form of PLLA crystalline residues.     

Miscibility and hydrolytic degradation in alkaline solution of poly(l-lactide) and poly(p-vinyl phenol) blends

Poly(l-lactide) (PLLA) was melt-blended with poly(p-vinyl phenol) (PVPh) using a two-roll mill, and the miscibility between PLLA and PVPh and degradation of the blend films were investigated. It was found that PLLA/PVPh blend has miscibility in the amorphous state because only single T_g was observed in the DSC and DMA measurements. The T_g of the PLLA/PVPh blend could be controlled in the temperature range from 55 °C to 117 °C by changing the PVPh weight fraction. In alkaline solution, degradation rate of PLLA/PVPh blends was faster than that of neat PLLA because PVPh could dissolve in alkaline solution. The surface morphology of degraded PLLA and PLLA/PVPh blend were observed by SEM. The surface morphology of degraded PLLA/PVPh blend was finer than that of PLLA. Young's modulus of PLLA/PVPh blend increased with increasing PVPh content. Yield stress of PLLA/PVPh blends whose PVPh content was less than 30 wt% kept the level of about 55 MPa and that of PLLA/PVPh blend whose PVPh content was 40 wt% is much lower than that of neat PLLA.     

Hydrolytic and enzymatic degradation of poly(trimethylene carbonate-co-d,l-lactide) random copolymers with shape memory behavior

A series of homo- and copolymers were synthesized by ring-opening polymerization of 1,3-trimethylene carbonate and d,l-lactide, using low toxic Zn(Lac)₂ as catalyst. The hydrolytic and enzymatic degradation of PTMC homopolymer and PTDLA copolymers was performed at 37 °C in pH 7.4 phosphate buffered saline or in pH 8.5 Tris buffer using proteinase K. Degradation was followed by using various analytical techniques such as NMR, GPC, DSC and ESEM. PTMC degrades extremely slowly by pure hydrolysis or in the presence of proteinase K. In contrast, PTDLA copolymers with different compositions degrade at various rates both in PBS and in enzyme solutions. The higher the LA content, the faster the degradation. LA units are preferentially degraded during hydrolytic degradation, indicating that ester bonds are more susceptible to hydrolytic cleavage than carbonate ones. Changes in surface morphology are observed during enzymatic degradation, in agreement with surface erosion process. The PTDLA11 copolymer with equivalent TMC/LA contents is highly elastic. Its residual strain is approximately 4% after the first cycle at a strain of 50%. The shape recovery ratio is up to 83%. Therefore, it is concluded that high molecular weight PTDLA copolymers are promising candidates for clinical applications in minimally invasive surgery.     

Structure and mechanical properties of poly(l-lactide)/layered silicate nanocomposites

Poly(ε-caprolactone) (PCL) masterbatches with the intercalated and the exfoliated morphology were prepared by ring opening polymerization of ε-caprolactone in the presence of organomodified montmorillonite (MMT) Cloisite 30B. Poly(l-lactide) (PLLA) nanocomposites with Cloisite 30B or PCL masterbatches were prepared by melt blending. The effects of the silicate type, MMT content and the nanocomposite morphology on thermal and mechanical properties of PLLA nanocomposites were examined. The montmorillonite particles in PLLA/Cloisite 30B and PLLA/intercalated masterbatch nanocomposites were intercalated. In contrary to expectations, the exfoliated silicate layers of exfoliated masterbatch were not transferred into the PLLA matrix. Due to a low miscibility of PCL and PLLA, MMT remained in the phase-separated masterbatch domains. The stress-strain characteristics of PLLA nanocomposites, Young modulus E, yield stress σ_y and yield strain ε_y, decreased with increasing MMT concentration, which is associated with the increase in PCL content. The expected stiffening effect of MMT was low due to a low aspect ratio of its particles and was obscured by both plastifying effects of PCL and low PLLA crystallinity. Interestingly, in contrast to the neat PLLA, ductility was enhanced in all PLLA/Cloisite 30B materials and in PLLA/masterbatch nanocomposites with low MMT concentrations.     

Nanocomposites of poly(l-lactide) and surface-grafted TiO2 nanoparticles: Synthesis and characterization

A new method of surface modification of TiO₂ nanoparticles by surface-grafting l-lactic acid oligomer was developed. The surface-grafting reaction was evaluated by Fourier transformation infrared (FTIR) and thermal gravimetric analysis (TGA). The results showed that l-lactic acid oligomer could be easily grafted onto the TiO₂ nanoparticles surface in the presence of stannous octanoate and the highest amount of grafted polymer was about 8.5% in weight. Transmission electron microscopy (TEM) and scanning electron microscopy (SEM) results showed that grafted TiO₂ (g-TiO₂) in chloroform or PLLA matrix approximated to uniform, while unmodified TiO₂ nanoparticles tended to aggregate. The tensile strength of this material was greatly improved by the addition of g-TiO₂ nanoparticles in poly(l-lactide) (PLLA) matrix. The tensile strength of the g-TiO₂/PLLA nanocomposite containing 5 wt.% of g-TiO₂ was 72 MPa, which was 23.1% higher than that of pure PLLA. Even though the incorporation of the TiO₂ nanoparticles into PLLA led to the deterioration of its elongation at break, the g-TiO₂/PLLA nanocomposite also exhibited better ductility than that of TiO₂/PLLA nanocomposite.     

Prevailing mechanisms of the hydrolytic degradation of oligo(d,l-lactide)-grafted dextrans

The predominant mechanism of the hydrolytic degradation of oligo(d,l-lactide)-grafted dextrans in phosphate buffer was followed by quantifying both released dextran and lactic acid from the copolymers. The studied amphiphilic copolymers, with well-defined structure, exhibited various oligo(d,l-lactide) weight fractions (F^OLA) while having a quite high extent of free hydroxyl groups (>90%). Depending on their F^OLA, oligo(d,l-lactide)-grafted dextrans were soluble either in water or in organic solvents (THF, toluene, …) and different prevailing mechanisms of hydrolytic degradation were observed. The copolymer soluble in THF, with longer oligo(d,l-lactide) grafts and higher F^OLA, was found to degrade via a particular mechanism by which the greatest part of dextran was released into buffer medium during the first two weeks of degradation. During the initial stage of degradation, the hydrophilicity of dextran backbone was considered to be the main driving force for the hydrolytic cleavage of the ester linkage between backbone and grafts. Released oligo(d,l-lactide) grafts were found to be degraded via chain-end degradation or random degradation depending on their solubility in buffer medium. In case of water-soluble copolymers with shorter oligo(d,l-lactide) grafts and lower F^OLA, the chain-end degradation was exclusively observed.