基于整体材料搅拌棒固相萃取高效液相色谱联用测定饲料和水样中硝基呋喃类药物残留

利用自制的以聚(乙烯基咪唑-二乙烯基苯)(VIDB)整体材料为涂层的固相萃取搅拌棒(VIDB-SBSE)萃取3种硝基呋喃类药物,然后与高效液相色谱-二极管阵列检测器联用建立了测定饲料和水样品中硝基呋喃类药物残留的方法。详细考察了萃取过程中萃取和解吸时间、样品基质的pH值以及离子强度等实验条件对萃取效率的影响。在最佳条件下,呋喃唑酮的线性范围为0.5~200μg/L,呋喃妥因和呋喃西林的线性范围为0.25~200μg/L,3种目标物的检出限(LO D)(S/N=3)在0.068~0.11μg/L之间,所建方法具有理想的日内和日间重现性(R SD值均小于6%)。在对饲料和实际水样的测定中,不同加标浓度呋喃唑酮、呋喃妥因和呋喃西林的回收率在80.6%~108%之间。研究表明,所建立的方法具有简便、灵敏、环境友好等特点。     

Determination of steroid sex hormones in wastewater by stir bar sorptive extraction based on poly(vinylpyridine-ethylene dimethacrylate) monolithic material and liquid chromatographic analysis

In this study, a simple and rapid method was developed for the determination of seven steroid hormones in wastewater. Sample preparation and analysis were performed by stir bar sorptive extraction (SBSE) based on poly(vinylpyridine-ethylene dimethacrylate) monolithic material (SBSEM) combined with high-performance liquid chromatography with diode array detection. To achieve the optimum extraction performance, several main parameters, including extraction and desorption time, pH value and contents of inorganic salt in the sample matrix, were investigated. Under the optimized experimental conditions, the method showed good linearity and repeatability, as well as advantages such as sensitivity, simplicity, low cost and high feasibility. The extraction performance of SBSEM to the target compounds also compared with commercial SBSE which used polydimethylsiloxane as coating. Finally, the proposed method was successfully applied to the determination of the target compounds in wastewater samples. The recoveries of spiked target compounds in real samples ranged from 48.2% to 110%.     

Direct enrichment of phenols in lake and sea water by stir bar sorptive extraction based on poly (vinylpyridine-ethylene dimethacrylate) monolithic material and liquid chromatographic analysis

A poly (vinylpyridine-ethylene dimethacrylate) monolithic material was synthesized and selected as stir bar sorptive extraction (SBSE) medium. The influences of polymerization conditions on the extraction efficiency were investigated using phenol and p-nitrophenol as target analytes. Based on this, six strongly polar phenols in water were directly concentrated by the new SBSE and determined with high performance liquid chromatography equipped with diode array detector. To achieve the optimum extraction performance, several main parameters, including extraction and desorption time, pH value and contents of inorganic salt in the sample matrix were investigated. The method showed good linearity and acceptable recoveries, as well as advantages such as sensitivity, simplicity, low cost and high feasibility. The proposed method was successfully applied to the determination of phenolic compounds in lake and sea waters.     

Preparation of a mixed stir bar for sorptive extraction based on monolithic material for the extraction of quinolones from wastewater

In this study, a novel mixed mode monolithic material was prepared and acted as the SBSE coating. The monolithic material was prepared by in situ copolymerization of methacrylic acid-3-sulfopropyl ester potassium salt (MASE) and divinylbenzene (DB) in the presence of a porogen solvent containing cyclohexanol, 1-dodecanol, and water with azobisisobutyronitrile as initiator. The influences of the contents of the porogen solvent and monomer in the polymerization mixture on the extraction performance were investigated thoroughly. Several characteristic techniques, such as elemental analysis, scanning electron microscopy and infrared spectroscopy were used to characterize the monolithic material. To achieve optimum extraction performance for quinolones, several parameters, including pH value, desorption solvent, ionic strength in sample matrix, extraction and desorption time were investigated. The results show that under the optimized experimental conditions, the method has good sensitivity, linearity, simplicity and low cost. The extraction performance of present method to the target compounds was compared with commercial SBSE which using polydimethylsiloxane as coating and other SBSEs which based on monolithic materials. The comparative results indicate that present SBSE can extract the analytes more effectively than other SBSEs because both ion-exchange and hydrophobic interactions contribute to the extraction of quinolones.     

Simple and sensitive monitoring of sulfonamide veterinary residues in milk by stir bar sorptive extraction based on monolithic material and high performance liquid chromatography analysis

A simple, rapid, and sensitive method for the quantitative monitoring of five sulfonamide antibacterial residues (SAs) in milk was developed by stir bar sorptive extraction (SBSE) coupling to high performance liquid chromatography with diode array detection. The analytes were concentrated by SBSE based on poly (vinylimidazole–divinylbenzene) monolithic material as coating. The extraction procedure was very simple, milk was diluted with water then directly sorptive extraction without elimination of fats and protein in samples was required. To achieve optimum extraction performance for SAs, several parameters, including extraction and desorption time, desorption solvent, ionic strength and pH value of sample matrix were investigated. Under the optimized experimental conditions, low detection limits (S/N = 3) quantification limits (S/N = 10) of the proposed method for the target compounds were achieved within the range of 1.30–7.90 ng/mL and 4.29–26.3 ng/mL from spiked milk, respectively. Good linearities were obtained for SAs with the correlation coefficients (R²) above 0.996. Finally, the proposed method was successfully applied to the determination of SAs compounds in different milk samples and satisfied recoveries of spiked target compounds in real samples were obtained.     

搅拌棒固相萃取与液相色谱联用测定水样品中烷基酚类污染物

建立了简单、快速、灵敏测定水环境中的双酚A(BPA)、辛基酚(OP)、壬基酚(NP)的方法。以聚(N-乙烯基咪唑-二乙烯基苯)整体材料为涂层的搅拌棒固相萃取技术富集目标物,然后与高效液相色谱-二极管阵列检测器联用测定水样品中烷基酚类污染物。考察了萃取时间、解析时间、样品基质的pH值、离子强度等实验条件对萃取效率的影响。在最佳条件下,3种目标化合物的线性范围是1.0～200μg/L,检出限LOD(S/N=3)在0.13～0.66μg/L之间,定量限LOQ(S/N=10)在0.44～2.19μg/L之间。在对海水和污水处理厂的实际水样测定中,3种目标化合物的不同加标水平的回收率为37.8%～101.1%。本方法具有简便、快速、高效、灵敏等优点。     

Determination of steroid sex hormones in urine matrix by stir bar sorptive extraction based on monolithic material and liquid chromatography with diode array detection

A simple, rapid and sensitive method for simultaneous determination of six steroid sex hormones in urine matrix was developed by the combination of stir bar sorptive extraction (SBSE) with high performance liquid chromatography (HPLC) and diode array detection (DAD). A poly (methacrylic acid stearyl ester-ethylene dimethacrylate) was synthesized and selected as SBSE extraction medium. To achieve the optimum extraction performance, several parameters, including agitation speed, desorption solvent, extraction and desorption time, pH value, inorganic salt and organic solvent content of the sample matrix were investigated. Under the optimized experimental conditions, low detection limits (S/N=3) and quantification limits (S/N=10) of the proposed method for the target compounds were achieved within the range of 0.062-0.38 and 0.20-1.20 ng/mL, respectively from spiked urine, respectively. The calibration curves of six steroid sex hormones showed good linearity ranging from 1.0 to 200 ng/mL with linear coefficient R2 values above 0.990. Good method reproducibilities presented as intra- and inter-day precisions were also found with the R.S.D.s less than 9.2 and 10.0%, respectively. Finally, the proposed method was successfully applied to the determination of the target compounds in a urine sample from a pregnant woman.     

分子印迹聚合物为涂层的吸附萃取搅拌棒在环境水样双酚A含量测定中的应用

以双酚A(BPA)为单体,利用整体材料“原位”聚合技术制备以分子印迹聚合物为涂层的吸附萃取搅拌棒(MIP-SBSE),然后与高效液相色谱(HPLC)-二极管阵列检测器联用,探讨其对环境水样BPA的选择萃取性能。优化萃取过程中吸附和解吸时间、解吸液种类以及基底pH值和离子强度对目标化合物的选择吸附性能。在最佳条件下,MIP-SBSE可对模板分子进行有效的选择吸附,线性范围为1.0～200 μg/L,检出限(S/N=3)和定量限(S/N=10)分别为0.28μg/L和0.94 μg/L。在实际水样分析中,具有良好的加标回收率,其值为96.0%～108.7%。研究结果表明,所建立的方法具有简便、灵敏和环境友好等特点。     

Development and validation of stir bar sorptive extraction of polar phenols in water followed by HPLC separation in poly(vinylpyrrolididone‐divinylbenzene) monolith

An effective and simple method for polar phenols in water matrix was developed by using stir bar sorptive extraction (SBSE) based on a hydrophilic poly(vinylpyrrolididone‐divinylbenzene) (VPDB) monolithic material and HPLC analysis. To achieve optimum extraction performance for phenols, several parameters, including extraction and desorption time, desorption solvent, pH value, and ionic strength of sample matrix, were investigated. Under the optimized experimental conditions, eight phenols were directly enriched from water samples and analyzed by HPLC‐DAD. The detection limits (S/N = 3) and quantification limits (S/N = 10) of the proposed method for the target compounds were achieved within the range of 0.72–1.37 and 2.40–4.27 ng/mL from spiked water, respectively. Recoveries of eight phenolic compounds were found in the range of 55.2–95.9%. The calibration curves showed the linearity ranging from 5 to 150 ng/mL with linear regression coefficient R² values above 0.98. Method repeatability presented as intra‐ and interday precisions were also found with the RSDs less than 4.10 and 7.61%, respectively. The distribution coefficients between VPDB and water (K_VPDB/W) for phenolic compounds were also calculated and compared with K_O/W. Finally, the proposed method was successfully applied to the determination of the target compounds in tap water, sea water and wastewater samples.     

pH-resistant titania hybrid organic-inorganic coating for stir bar sorptive extraction of drugs of abuse in urine samples followed by high performance liquid chromatography-ultraviolet visible detection

An organic-inorganic hybrid titania-hydroxy-terminated silicone oil (titania-OH-TSO) stir bar coating was prepared by sol-gel method. The extraction performance of titania-OH-TSO coated stir bar was evaluated and compared with poly(dimethysiloxane) (PDMS), poly(dimethysiloxane)-divinylbenzene (PDMS-DVB), poly(dimethysiloxane)-β-cyclodextrin (PDMS-β-CD) and C(18) coated stir bar with five polar drugs of abuse including amphetamine (PA), methamphetamine (MA), 3,4-methylenedioxyamphetamine (MDA), 3,4-methylenedioxymethamphetamine (MDMA) and ketamine (Ke) as the model analytes. The experimental results revealed that the titania-OH-TSO coated stir bar exhibited highly pH-resistant ability, good preparation reproducibility, superior selectivity and high extraction efficiency for the target compounds. Based on this fact, a new method of titania-OH-TSO coated stir bar sorptive extraction (SBSE) combined with high performance liquid chromatography (HPLC)-ultraviolet visible (UV) detection was developed for the analysis of five drugs of abuse in urine samples. The factors affecting the extraction efficiency of SBSE such as sample pH, desorption solvent, sample volume, extraction time, desorption time, stirring rate and ionic strength were investigated and the optimal extraction conditions were established. Under the optimized conditions, the limits of detection (LODs) for titania-OH-TSO coated SBSE-HPLC-UV determination of five polar drugs of abuse were in the range of 2.3-9.1 μg/L with relative standard deviations (RSDs) ranging from 7.3 to 8.9% (c=300 μg/L, n=6), and all of the target compounds exhibited good linearity over a concentration range of 30-3000 μg/L. The developed method was applied to the determination of amphetamines and Ke in urine samples of drug abusers with satisfactory results.     

Development and application of stir bar sorptive extraction with polyurethane foams for the determination of testosterone and methenolone in urine matrices

This work describes the development, validation, and application of a novel methodology for the determination of testosterone and methenolone in urine matrices by stir bar sorptive extraction using polyurethane foams [SBSE(PU)] followed by liquid desorption and high-performance liquid chromatography with diode array detection. The methodology was optimized in terms of extraction time, agitation speed, pH, ionic strength and organic modifier, as well as back-extraction solvent and desorption time. Under optimized experimental conditions, convenient accuracy were achieved with average recoveries of 49.7 8.6% for testosterone and 54.2 ± 4.7% for methenolone. Additionally, the methodology showed good precision (<9%), excellent linear dynamic ranges (>0.9963) and convenient detection limits (0.2-0.3 μg/L). When comparing the efficiency obtained by SBSE(PU) and with the conventional polydimethylsiloxane phase [SBSE(PDMS)], yields up to four-fold higher are attained for the former, under the same experimental conditions. The application of the proposed methodology for the analysis of testosterone and methenolone in urine matrices showed negligible matrix effects and good analytical performance.     

Preparation of cation-exchange stir bar sorptive extraction based on monolithic material and its application to the analysis of soluble cations in milk by ion chromatography

In this study, a new cation-exchange coating for stir bar sorptive extraction (SBSE) based on poly (acrylic acid-ethylene dimethacrylate) monolithic material was synthesized. The effect of polymerization conditions such as the ratio of functional monomer to cross-linker and the content of porogenic solvent on the extraction efficiencies were investigated in detail. The monolithic material was characterized by elemental analysis, scanning electron microscopy and infrared spectroscopy. In order to evaluate the usability of the new coating for the extraction of inorganic cations, the analysis of soluble K(+), Mg(2+) and Ca(2+) in milk by ion chromatography with conductivity detection was selected as a paradigm. Several extractive parameters, including pH value in sample matrix, desorption solvent, extraction and desorption time were optimized. Under the optimum conditions, low detection limits (S/N = 3) and quantification limits (S/N = 10) of the proposed method for the target cations were achieved within the range of 0.12-0.28 and 0.4-0.92 μg L(-1), respectively. The method also showed good linearity, simplicity, practicality and low cost for the extraction of inorganic cations. Finally, the proposed method was successfully used to analyse three different trademarks of commercial milk samples with satisfactory recoveries in the range of 71.1% to 102.8%.     

分子印迹固相萃取搅拌棒的制备及对复杂样品中双烯雌酚和己烷雌酚的萃取性能

以己烯雌酚为替代模板,利用整体材料的“原位”合成技术制备了分子印迹聚合物,并将其作为固相萃取搅拌棒的涂层(MIP-SBSE)制备了新的搅拌棒。详细考察了分子印迹聚合物制备条件中模板分子及功能单体用量对MIP-SBSE选择性萃取性能的影响,同时利用元素分析、扫描电镜和红外光谱对聚合物进行表征。以双烯雌酚(DS)和己烷雌酚(HS)为目标化合物,将MIP-SBSE与高效液相色谱-二极管阵列检测器联用,建立起复杂样品中DS和HS的分离分析方法。考察了吸附和解吸时间、解吸溶剂、离子强度和样品pH值等萃取条件对MIP-SBSE选择性萃取性能的影响。结果表明,在最佳萃取条件下,MIP-SBSE对DS和HS具有较高的选择性萃取性能,线性范围分别为1.0～400.0 μg/L和5.0～400.0 μg/L,利用氮吹再定容的方法,对DS和HS的检出限(S/N=3)分别可低至0.04和0.14 μg/L。在对实际污水、蜂蜜和牛尿样品的分析中取得了良好的加标回收率,其值为61.3%～120%。所建方法具有简便、高选择性和灵敏等特点,可用于复杂样品中双烯雌酚和己烷雌酚的分析监测。     

硼亲和吸附剂的制备及其对苯甲酰脲类农药的萃取性能

以3-丙烯酰胺苯硼酸（APB）为单体,二乙烯基苯（DVB）为交联剂,“原位”聚合制备了聚（3-丙烯酰胺苯硼酸-二乙烯基苯）多孔硼亲和整体材料并作为搅拌饼固相萃取（SCSE-APBDVB）的萃取介质。以5种苯甲酰脲农药为目标化合物,详细考察了萃取过程中解吸溶剂、样品基底中pH值以及离子强度、萃取和解吸时间等实验条件对萃取效率的影响。在此基础上,与高效液相色谱-二极管阵列检测器联用建立了环境水样和果汁样品中苯甲酰脲农药残留的测定方法。在最佳条件下,在水样和果汁样品中,5种目标化合物的检出限（LOD,S/N=3）分别在0.055~0.11 μg/L和0.095~0.31 μg/L之间,所建立的方法具有理想的日内和日间重现性（RSD值均小于9.0%）。在对实际环境水样和果汁样品的测定中,不同加标浓度苯甲酰脲的回收率为75.6%~109%。研究表明,由于所制备吸附剂与目标化合物存在B-N配位作用、氢键和疏水等多种作用力,因此SCSE-APBDVB可对苯甲酰脲农药进行有效萃取,所建立的分析方法具有简便、灵敏和环境友好等特点。     

Development of monolith-based stir bar sorptive extraction and liquid chromatography tandem mass spectrometry method for sensitive determination of ten sulfonamides in pork and chicken samples

A highly sensitive method was developed for the simultaneous determination of ten sulfonamides in pork and chicken samples by monolith-based stir bar sorptive extraction (SBSE) coupled to high-performance liquid chromatography tandem mass spectrometry. The samples were freeze-dried and extracted by acetonitrile, then enriched and further extracted by SBSE which was based on poly(vinylphthalimide-co-N,N-methylenebisacrylamide) monolith (SBSE-VPMB) as coating. To achieve optimum extraction performance of SBSE for sulfonamides, several parameters, including pH value and ionic strength in the sample matrix and extraction and desorption time, were investigated in detail. Under the optimal conditions, the limits of detection (S/N?=?3) for target sulfonamides were 1.2–6.1 ng/kg in pork and 2.0–14.6 ng/kg in chicken, respectively. Real samples spiked at the concentration of 0.5 and 5.0 μg/kg showed recoveries above 55 % and relative standard deviations below 12 %. At the same time, the extraction performances of target sulfonamides on SBSE-VPMB were compared with other SBSE based on porous monolith and commercial SBSE.

整体式吸附萃取搅拌棒在检测环境水样中镉离子含量方面的应用

通过逐步聚合反应制备了一种新型整体式吸附萃取搅拌棒,将其应用于环境水中镉离子的吸附萃取.考察了介质酸度、搅拌速率、吸咐时间、解吸溶剂和时间等实验条件对吸附量的影响.控制溶液pH为6.0,搅拌棒转速为300 r/min,吸附30 min,5% HNO3作为解吸液解吸10 min,采用等离子体原子发射光谱仪对Cd离子进行检...     

固相萃取搅拌棒萃取-气相色谱分析海水中的多环芳烃

利用固相萃取搅拌棒（SBSE）萃取海水中的多环芳烃，然后用热解吸脱附-气相色谱分析。研究了萃取时间、添加NaCl浓度对萃取效率的影响。实验结果表明，SBSE方法对16种多环芳烃的萃取回收率分别在33．5％～122．4％之间；对标准样品的检出限为2．74-13．5ng／L；方法RSD为3．8％～13．1％。用此方法测定了大连海岸海水中的多环芳烃含量。     

大体积搅拌棒吸附萃取技术与热脱附-气相色谱-质谱法测定地表水中多环芳烃

基于搅拌棒吸附萃取(SBSE)技术建立了气相色谱-质谱测定地表水中16种多环芳烃(PAHs)的分析方法。该法采用多搅拌吸附棒同时富集,依次热脱附冷聚焦后进样的方式有效解决了搅拌棒吸附时间长、富集水样体积小等问题。优化后的结果表明,在0.2~10 ng/L范围内(萘为0.5~10 ng/L范围),16种PAHs的线性关系良好,相关系数(r)均0.99,方法检出限(MDL)为0.03~0.20 ng/L(萘为0.50 ng/L)。用该方法对钱塘江流域地表水进行测定,共检测出11种PAHs,含量为0.13~1.57 ng/L,不同添加水平下的加标回收率为75.6%~108.9%。该法可应用于地表水样品中该类物质的超痕量检测。     

Analysis of 35 priority semivolatile compounds in water by stir bar sorptive extraction-thermal desorption-gas chromatography-mass spectrometry. I. Method optimisation

A multiresidue method for the determination of 35 organic micropollutants (pesticides and polycyclic aromatic hydrocarbons) in water has been optimised using stir bar sorptive extraction (SBSE) and thermal desorption coupled to capillary gas chromatography-mass spectrometry (GC-MS). In the present work, the different parameters affecting the extraction of the analytes from the water samples to the PDMS-coated stir bars and optimisation of conditions affecting thermal desorption are investigated. The optimised conditions consist of a 100-ml water sample with 20% NaCl addition extracted with 20 mm length x 0.5 mm film thickness stir bars at 900 rpm during 14 h at ambient temperature. Desorption is carried out at 280 degrees C during 6 min under a helium flow of 75 ml/min in the splitless mode while maintaining a cryofocusing temperature of 20 degrees C in the programmed-temperature vaporisation (PTV) injector of the GC-MS system. Finally, the PTV injector is ramped to a temperature of 280 degrees C and the analytes are separated in the GC and detected by MS using full scan mode (m/z 60-400). Under the described conditions, the good repeatability, high analyte recoveries and robustness, make SBSE a powerful tool for routine quality control analysis of the selected semivolatile compounds in water samples.     

聚酰亚胺固相萃取搅拌棒的制备及其在环境水中酚类的分析应用

利用相转换法制备了聚酰亚胺吸附萃取搅拌棒,用5种有机酚作为评价标样,并与现有商品化吸附萃取搅拌棒进行比较。优化了萃取搅拌速度、溶液离子强度、萃取温度、萃取时间以及热解析温度和时间。在最佳实验条件下,100 mL 样品,30% NaCl,在25℃下,经活化5 min 后的聚酰亚胺吸附搅拌棒萃取30 min (800 r/ min),然后300℃热解析4 min,使目标物脱附,再进行色谱分析。目标物在大于两个数量级浓度范围内具有良好的线性(R≥0.9995),定量限(LOQ,S/ N=10)为0.028~0.123μg/ L,重复性为1.6%~9.7%。将SBSE 与气相色谱-质谱联用,对海水、自来水和污水中的酚类进行定性与定量分析,结果表明,聚酰亚胺吸附萃取搅拌棒具有良好的选择性,最高热解析温度350℃,在分析水中痕量极性化合物领域具有广阔应用前景。