均聚物调节的金纳米粒子光及催化活性

在均聚物甲基丙烯酸N,N-2甲氨基乙酯（PDMAEMA）存在下通过硼氢化钠原位还原制备金纳米粒子,其尺寸通过金与DMAEMA的摩尔比调节．PDMAEMA水溶液在pH10和14分别在25℃和50℃发生相转变,而由于金纳米粒子具有疏水性,PDMAEMA稳定的金纳米粒子胶体水溶液在pH10时在47℃发生相变．PDMAEMA具有pH和温度敏感特性,其稳定的金纳米粒子胶体水溶液在光和催化性能方面表现出pH可调节的温度敏感特性．在pH2的酸性条件下,胶体水溶液从20℃到65℃升温过程中在518nm处发生表面等离子吸收;在pH10碱性条件下,胶体水溶液在20℃-40℃温度范围内在518nm处出现表面等离子吸收,而在40℃-65℃温度范围内吸收从518nm红移到545nm．当用金纳米粒子做催化剂催化对硝基苯酚的还原反应时,其催化活性可根据PDMAEMA在较高和较低温度对反应物分子的渗透性改变进行调节．     

多重响应性超支化星形聚合物的合成与组装以及控制释放研究

含二硫键的自引发单体与2-(2-甲氧基乙氧基)乙基甲基丙烯酸酯(MEO₂MA)进行自缩合乙烯基共聚合得到超支化PMEO₂MA(H-PMEO₂MA). 以它作大分子引发剂, 引发二甲氨基乙基甲基丙烯酸酯(DMAEMA)进行原子转移自由基聚合, 合成了具有温度、pH以及氧化还原多重响应性的超支化星形聚合物H-PMEO₂MA-star-PDMAEMA. 证明了H-PMEO₂MA有低临界溶液温度(LCST); 研究了PDMAEMA 链段的长度和溶液的pH值对超支化星形聚合物的LCST的影响. 当H-PMEO₂MA-star-PDMAEMA水溶液温度从2 ℃升高至室温, H-PMEO₂MA变成疏水性而发生聚集, 形成以H-PMEO₂MA为核, PDMAEMA为壳的胶束. 在胶束形成过程中, 将尼罗红装载到这种聚合物胶束中, 形成释药系统, 研究了pH、氧化还原响应性释药性能.     

不同嵌段比的PEG-b-PDMAEMA共聚物在水溶液中的自聚集行为

采用氢核磁共振(¹H-NMR)、动态光散射(DLS)及透射电子显微镜(TEM)对聚乙二醇-嵌段-聚甲基丙烯酸N,N-二甲氨基乙酯(PEG-b-PDMAEMA)三种具有不同PEG/PDMAEMA嵌段比的PEG-b-PDMAEMA共聚物在水溶液中的自聚集行为进行了研究. 研究表明, 两嵌段比例是影响聚合物胶束化过程的关键因素: 只有当其中聚乙二醇含量较低(质量分数低于33%)时, 聚合物才具有其pH/温度敏感胶束化特性. 此外, 共聚物溶液随温度胶束化过程与共聚物嵌段比大小密切相关. PEG-b-PDMAEMA这种不同于传统双亲性嵌段共聚物(DHBCs)在选择性溶剂中独特的胶束化行为, 是由聚合物溶液体系中各种基团之间的氢键作用决定的.     

CO2调控的温敏性聚合物的制备及其响应行为

通过原子转移自由基聚合制备了含甲氧基聚乙二醇(mPEG)、N-异丙基丙烯酰胺(PNIPAM)和2-(二乙基氨基)甲基丙烯酸乙酯(PDMAEMA)的三嵌段共聚物。该共聚物具有较为明显的温度响应特征，并且温敏性的范围可以通过CO₂进行调控。该三嵌段聚合物在水溶液中存在最低临界溶液温度(LCST)，且该聚合物水溶液在CO₂调节的LCST下具有各种聚集状态。随着温度的升高，三嵌段聚合物表现出双重LCST行为，并最终导致PNIPAM嵌段和PDMAEMA嵌段分别在各自相转变温度下收缩，聚合物的疏水性增强,出现收缩-收缩-聚集的三相变过程。CO₂通过调控PDMAEMA嵌段中的叔胺基团电性，可以使聚合物的亲水性增强，使得三嵌段聚合物在较高温度下难以聚集，实现了CO₂对聚合物相转变温度的调控。      

酶促聚合与ATRP结合合成聚己内酯和聚N,N-二甲氨基甲基丙烯酸乙酯嵌段共聚物及其自组装

摘要：用化学酶法合成聚己内酯（PCL）和聚N,N-二甲氨基甲基丙烯酸乙酯（PDMAEMA）双亲嵌段聚合物（PCL-b-PDMAEMA）。通过核磁共振（1H NMR）,红外光谱仪(FTIR-IR),凝胶渗透色谱(GPC) 对其结构以及分子量与其分子量分布情况进行了表征。对聚合物的溶液性质进行了研究,结果表明：临界胶束浓度（CMC）嵌段聚合物中疏水链段增多有利于形成胶束,表现为CMC降低,并具有较高的热力学稳定性。PDMAEMA是PH和温度敏感材料,研究发现,在不同的温度和pH值条件下表现不同的聚集状态, 当聚合物的pH值降低时平均流体力学直径增加,温度升高平均流体力学直径降低。     

十四烷基芳基磺酸盐形成的分子有序组合体

以表面张力法、碘光谱法、水增溶法和相态图法研究了自制的三种十四烷基芳基磺酸盐在不同条件下形成的分子有序组合体(胶束、反胶束和微乳液),并考察了分子结构、溶剂、无机盐和短链醇等对其的影响.结果表明:增加十四烷基芳基磺酸盐分子亲油基支化度,不利于其在水溶液或混合极性溶剂(乙二醇-水)中形成胶束而有利于其在非极性溶剂正庚烷中形成反胶束;溶剂极性的降低,促使表面活性剂溶液由胶束溶液→单体溶液→反胶束溶液转变;无机盐或短链醇的加入促进了水溶液中胶束的形成,且反离子价态数或醇烷基碳原子数越大,越有利于胶束形成;无机盐浓度的增加导致表面活性剂/正丁醇/正辛烷/NaCl/水形成的微乳液体系在一定温度下发生由WinsorI→WinsorIII→WinsorII型的转变.     

pH响应性阳离子型微凝胶的制备及性质研究

以甲基丙烯酸-(N,N-二甲氨基)乙酯(DMAEMA)和丙烯酸乙酯(EA)为共聚单体, 二甲基丙烯酸乙二醇酯(EGDMA)为交联剂, 采用半连续乳液聚合法, 制备了具有pH响应性的阳离子型微凝胶, 并研究不同聚合条件对所合成的微凝胶性质的影响. 利用透射电子显微镜(TEM)、激光粒度分析仪和流变仪对微凝胶进行一系列表征. 研究了介质pH值对微凝胶的形态、平均粒径、zeta电位、溶液浊度(透光率)的影响, 以及NaCl盐溶液对微凝胶分散体系稳定性的影响. 结果表明, 这类阳离子型微凝胶体系具有良好的pH响应性, 在pH＝7左右发生相转变. 此外, 研究表明不同浓度NaCl溶液对微凝胶的稳定性有一定影响, 临界絮凝浓度约为1.3 mol•L－1.     

淀粉/丙烯酸反相乳液体系的稳定性研究

以丙烯酸(AA)单体的水溶液为水相,液体石蜡为油相,失水山梨醇三油酸酯(Span 85)和辛基苯基聚氧乙烯醚(Opan 10)为复合乳化剂,合成了淀粉/丙烯酸反相乳液;考察了乳化剂亲水亲油平衡值(HLB值)、油水比、乳化剂用量、单体浓度、温度对乳液稳定性和类型的影响.结果表明,合成淀粉/丙烯酸稳定反相乳液体系的适宜条件...     

嵌段共聚物OSM1-PCLA-PEG-PCLA-OSM1的合成及其pH和温度敏感性

采用开环聚合法和自由基聚合法合成了生物可降解嵌段共聚物OSM1-PCLA-PEG-PCLA-OSM1, 并对其进行了结构表征. 采用荧光分光光度计和激光粒度仪对共聚物溶液临界胶束浓度(CMC)和粒径大小及分布进行了考察, 研究了温度和pH对共聚物胶束形成的影响. 相转变过程研究结果表明, 共聚物溶液具有pH和温度双重敏感性. 共聚物溶液在一定温度和pH条件下可发生溶液-凝胶相转变.     

P（MMA—co—AA）乳液的制备及pH响应特性

以过硫酸钾(KPS)为引发剂、十二烷基硫酸钠(SDS)为乳化剂,利用正相乳液聚合制备(甲基丙烯酸甲酯-co-丙烯酸)共聚物(P(MMA-co-AA))乳液.通过测定聚合转化率和观察聚合过程稳定性,探讨了AA与MMA不同质量比时制备稳定的共聚物乳液的工艺条件;通过黏度法测定了乳液在不同pH时的相对黏度η,利用粒度分析仪分析了乳胶粒子在不同pH时的平均粒径和粒径分布.结果表明:AA含量较高时,控制聚合时间是得到稳定聚合物乳液的关键,当m(AA)/m(MMA)=12.5/100,65 ℃下反应120 min时,所制得的乳液稳定性最好.随着pH增大,乳液黏度先增大后降低;随着m(AA)/m(MMA)增加,制得的乳液pH敏感性增大;随着乳液从酸性(pH=5.17)变到碱性(pH=8.61),聚合物乳胶粒子平均粒径减小,粒径分布变窄.     

反相乳液共聚合制备两性丙烯酰胺共聚物的研究

采用Span80-Tween80复合乳化剂和AIBA引发剂,进行丙烯酸钠(NaAA)/丙烯酰胺(AM)/丙烯酰氧基乙基三甲基氯化铵(DAC)反相乳液共聚合.研究了聚合温度、引发剂用量、单体浓度、共聚单体中DAC和AM含量、乳化剂用量及其HLB值、水/油比和水相pH值等聚合反应工艺条件或参数对聚合反应单体转化率和聚合物特性粘度的影响,聚合物特性粘度随引发剂用量和单体浓度的增大而增大的实验结果证实了该两性丙烯酰胺共聚物反相乳液制备过程中凝胶效应的存在.傅立叶红外光谱组成分析表明了两性丙烯酰胺共聚物的成功合成,扫描电镜观测乳胶粒粒径范围在0.6~8.0μm.     

含氟丙烯酸酯三元共聚物乳液的研究

以丙烯酸全氟烷基酯 (ZonylTM)、甲基丙烯酸甲酯 (MMA)、丙烯酸丁酯 (BA)为原料 ,在阴离子乳化体系中制备了含氟丙烯酸三元共聚物乳液 .研究了聚合反应动力学、转化率的各种影响因素 ,得出了聚合速率方程 ,并得出反应的表观活化能 (Ea)为 5 0 75 8kJ mol.考察了乳液的稀释稳定性、贮存稳定性、离心稳定性、耐热、耐寒稳定性 ,及乳胶膜的吸水性和耐溶剂性 .并用Wilhelmy方法测定了乳胶膜与水的接触角 ,结果表明乳胶膜对水的抗浸润力大大提高     

Specific thermoresponsiveness of PMMA-block-PDMAEMA to selected ions and other factors in aqueous solution

Poly(2-(dimethylamino)ethyl methacrylate) (PDMAEMA) is a functional polymer that presents positive charges at low and neutral pHs. Copolymers bearing PDMAEMA blocks usually show a thermal behavior in water marked by a lower critical solution temperature (LCST). This behavior suggests them as interesting “smart” materials for several applications such as water decontamination and many others. In the present work, the LCST of a poly(methyl methacrylate)-block-poly(2-(dimethylamino)ethyl methacrylate) (PMMA-b-PDMAEMA) synthesized by RAFT was measured in several conditions in aqueous solution. It was demonstrated that ionic strength modulates the LCST and this effect depends on the nature of the anion. For instance, weakly hydrated anions such as perchlorate make the LCST lower as the ionic strength gets higher, on the other hand, strongly hydrated ions such as sulfate have not shown a marked effect on LCST. Those results were understood as a consequence of the specific binding of each anion onto the positive-charged PDMAEMA chains, changing the interactions between the chains and water molecules, as well as affecting their pK _a and the ionic interactions. Also, as expected, the LCST is very dependent on pH. The overall results point to the opportunity of modulating very precisely the thermal behavior of PMMA-b-PDMAEMA systems by usual solution conditions such as the type of the anion present.     

由聚丙二醇二缩水甘油醚和甘油制备温敏性超支化聚合物

由聚丙二醇二缩水甘油醚和甘油通过质子转移聚合(proton transfer polymerization)一步法制备了端羟基的温敏性超支化聚醚.聚合产物的分子量(Mn)在1.76×104~2.43×104之间,玻璃化转变温度(Tg)在-31.5~-26.7℃之间,热分解温度(Td)在367~376℃之间.通过控制聚丙二醇二缩水甘油醚和甘油的投料比,实现了对温敏性超支化聚醚最低临界溶解温度(LCST)的调节,LCST可控制在28.3~39.6℃之间.     

CONCURRENT INTERACTIONS BETWEEN MONOMER - EMULSIFIER AND MONOMER - POLYMER IN POLYVINYL ACETATE LATEXES

In the poly(vinyl acetate) latexes stabilized by nonyl phenol ethoxylated with 30 moles ethylene oxide, the ratio of the amount of monomer that swells the polymer particles to that of monomer remaining in aqueous phase decreases with the increase of the emulsifier concentration.

This behaviour is due to concurrent interactions between monomer - polymer and emulsifier - polymer. At the polymer particle/water interface, the monomer interacts with the adsorbed emulsifier and prevents to swelling process from occuring.     

氯丁胶乳乳液接枝甲基丙烯酸甲酯的反应动力学

采用乳液聚合法将甲基丙烯酸甲酯(MMA)接枝到氯丁胶乳上,红外光谱和核磁共振氢谱证实了接枝产物的生成。 研究了反应温度、乳化剂浓度、引发剂浓度和单体浓度对表观聚合速率的影响。 结果表明,当反应温度为50 ℃,引发剂叔丁基过氧化氢 四乙烯五胺（t-BHP/TEPA）用量为氯丁胶乳干重的0.5%,单体/聚合物质量比m(M)∶m(P)=3∶5,乳化剂十二烷基连苯醚二磺酸钠（DSB）用量为单体总质量1%时,单体转化率和接枝效率分别为99.1%和54.9%。 聚合反应动力学关系式为：Rp=Kc(E)0.15c(I)0.30c(MMA)1.41,式中,K为常数,在40~55 ℃范围内,聚合反应的表观活化能Ea＝60.2 kJ/mol。 接枝聚合基本符合自由基反应机理。     

温度及pH敏感聚(丙烯酸)/聚(N-异丙基丙烯酰胺)互穿聚合物网络水凝胶的合成及性能研究

合成聚（丙烯酸）／聚（Ｎ 异丙基丙烯酰胺）互穿聚合物网络（ＰＡＡｃ／ＰＮＩＰＡＩＰＮ）水凝胶，具有温度及ｐＨ双重敏感特性．这种水凝胶在弱碱性条件下的溶胀率远大于酸性条件下的溶胀率．在酸性条件下，随着温度上升，凝胶的溶胀率也随之逐渐上升；而在弱碱性条件下，温度低于聚（Ｎ 异丙基丙烯酰胺）（ＰＮＩＰＡ）的较低临界溶解温度（ＬＣＳＴ）时，溶胀率也随着温度的上升而上升，当温度达到ＬＣＳＴ时，凝胶的溶胀率突然急剧下降，并随着温度的逐渐上升而下降．     

The effect of pH on emulsion polymerization of styrene in the presence of an amphoteric emulsifier

An emulsion polymerization of styrene in the presence of an amphoteric emulsifier of the betaine type; N,N-dimethyl-n-laurylbetaine (LNB), has been studied at various pH values. The relationships between the physicochemical properties of LNB aqueous solutions, the emulsion polymerization process and the characteristics of the synthesized latex particles were studied under various pH conditions. The polymerization rate and the particle number concentration decreased with increasing pH of LNB aqueous solution and changed in shape at both ca. pH 4 and pH 8–10. The properties of LNB aqueous solution also changed with the pH and changed in shape at the same pH as that of the emulsion polymerization. These pH values were in good agreement with the pH at which the LNB molecule changed its ionic form. The number of synthesized latex particles was proportional to the number of LNB micelles in the solution, below pH 10. The particle size of the synthesized latex particles and the molecular weight of the latex polymers also changed with the properties of LNB aqueous solutions, accompanying the change of the ionic form of LNB molecules.     

Emulsion polymerization. VI. Concentration of monomers in latex particles

Nonpolymerizing latex particles surrounded by an aqueous phase saturated with monomer absorb only a finite amount of monomer, even if the monomer is a good solvent for the polymer, because the surface energy of each particle increases on swelling. At equilibrium the change in surface energy and the free energy of mixing exactly balance. Equations based on this thermodynamic principle predict with good accuracy the saturation swelling of crosslinked and uncrosslinked latex particles and the partitioning of monomer between the aqueous phase and latex particles at partial saturation. The available experimental data on swelling of latex polymers with monomers are reviewed. Earlier papers assumed that during emulsion polymerization the monomer concentration in the latex particles is independent of conversion as long as monomer droplets are present. This assumption is shown to be a justifiable approximation. The thermodynamics of the swelling of latex particles with a blend of two monomers is presented. The calculations indicate that copolymerization in emulsion should define reactivity ratios differing from those of homogeneous copolymerization by not more than 40% if the solubility of the comonomers in water is low. The reactivity ratio scheme is strictly applicable to emulsion copolymerization if the solvent properties of the two comonomers are identical.