碱溶性无规共聚物表面活性剂的合成及在乳液聚合中的应用研究

合成了碱溶性无规共聚物聚 (甲基丙烯酸甲酯 丙烯酸乙酯 甲基丙烯酸 ) (MMA EA MAA) ,并对其结构、表面活性进行了表征研究 .以合成的P(MMA EA MAA)作高分子表面活性剂 ,进行甲基丙烯酸丁酯的乳液聚合 .研究了反应温度 ,引发剂浓度 ,表面活性剂浓度等因素对反应速率 (Rp)的影响 .结果表明 ,聚合速率随引发剂浓度 ,表面活性剂浓度的增加而增加 ;该体系的表观活化能为 85 19kJ·mol- 1 .用透射电镜 (TEM)表征了所制备的乳胶粒子形态 ,乳胶粒子呈较明显的核 壳结构 .     

碱溶性茶多糖的提取及其分析

在煎煮后的低档绿茶茶渣中提取碱溶性茶多糖,经HPGPC-ELSD法分析其含有3种均一性多糖组分,依出峰顺序其质量分数约为5.96%、78.99%和15.05%;GC-MS法测得组成碱溶性茶多糖的6种单糖:鼠李糖、阿拉伯糖、木糖、甘露糖、葡萄糖和半乳糖,并分析了其摩尔比例.紫外-可见吸收光谱分析显示,碱溶性茶多糖在250～290 nm区段有"波浪状"吸收.红外光谱表征了碱溶性茶多糖的特征,圆二色谱分析了其水溶液的cotton效应.结果表明,在190 nm有正cotton效应,在203 nm有负cotton效应.     

季戊四醇-偏苯三酸酐-环氧氯丙烷合成超支化聚合物

以季戊四醇为“中心核”,与1,2,4-偏苯三甲酸酐和环氧氯丙烷反应合成超支化碱溶性聚酯,利用合成聚合物分子外围的羧基与甲基丙烯酸缩水甘油酯反应,在超支化聚合物分子外围引入反应性甲基丙烯酰氧基.研究了树脂组成对感光性和碱溶性的影响.结果表明:通过调整分子外围的羧基及反应性甲基丙烯酰氧基含量,可以获得较好的碱溶性和光固化性能.     

丙烯酰胺-苯乙烯双亲嵌段共聚物水溶液的表面活性及增溶性

在微乳液介质中制备了系列的丙烯酰胺 (AM)与苯乙烯 (St)的双亲嵌段共聚物 (PAM b PSt) ,用紫外分光光度法测定了共聚物的组成 ,用乌氏粘度计测定了共聚物的特性粘数 [η],并用其相对表征共聚物的分子量大小 .重点研究了双亲嵌段共聚物 (PAM b PSt)疏水链段在水溶液中的缔合行为、共聚物的表面活性及其对有机物的增溶性能 ,考察了共聚物分子组成 (疏水链段含量 )与分子量对其表面活性与增溶性能的影响规律 .研究结果表明 ,由于疏水链段的憎水性 ,PAM b PSt的分子链在水溶液表面会形成表面吸附 ,从而降低水溶液的表面张力 ;而在水溶液中 ,在疏水相互作用下 ,PAM b PSt分子链中的苯乙烯疏水链段会形成分子间或分子内的胶束 ,烃类有机物可增溶其中 ;疏水链段含量越大 ,分子量越小 ,PAM b PSt的表面活性与增溶性能越强     

TA-EG-GMA合成超支化碱溶性感光聚合物

通过1,2,4-偏苯三酸酐和乙二醇反应合成超支化聚合物,利用合成聚合物分子外围的羧基与甲基丙烯酸缩水甘油酯反应,在超支化聚合物分子外围引入反应性甲基丙烯酰氧基.研究了树脂组成对感光性和碱溶性的影响.结果表明:调整反应物料配比及反应性甲基丙烯酰氧基含量,可以获得较好的碱溶性和光固化性能.     

含金鸡纳碱的光活性聚合物──Ⅰ．金鸡纳碱／丙烯酰胺共聚物的合成与表征

研究了金鸡纳碱与丙烯酰胺的自由基共聚反应。发现在氯仿／乙醇混合溶剂中采用硫酸奎宁作为金鸡纳碱共聚单体可以合成收率和金鸡纳碱含量均较高的新型水溶性共聚物。对共聚物用元素分析、核磁共振、粘度和旋光度测定等方法进行表征，发现在假定丙烯酰胺链节为非光活性的条件下共聚物中金鸡纳碱链节的比旋光度随聚合配方中金鸡纳碱含量的增加而增加。     

P(St-EAE-MAA)共聚物多孔微球的合成

利用无皂种子乳液聚合法合成了以聚苯乙烯(St)为骨架、丙烯酸乙酯(EA)和甲基丙烯酸(MAA)为共聚单体的P(St-EA-MAA)共聚物乳液;乳液经碱酸分步处理法制得共聚物多孔微球.考查了MAA用量和碱酸处理温度对微球形态的影响.     

无烟粉煤催化气化含碱灰渣的锻烧无害化

报道了福建劣质无烟粉煤催化气化含碱灰渣在一内径φ32mm的实验室固定床模试装置中的煅烧研究。对水蒸汽油催化和混合气（空气/水蒸汽）催化气化的两种含碱灰渣进行煅烧处理，生成了难溶性的硅酸复盐。当煅烧温度870℃-900℃、煅烧时间25min-30min，可以达到85W/%以上的脱碱率；而3W/%脱碱助剂的加入，可使脱碱率提高到95W/%以上，实现了含碱灰渣的煅烧无害化。粉煤催化气化制度与含碱灰渣煅烧制度的一致性提供了科学地实现“催化气化-灰渣煅烧”集成式流化床新工艺的理论依据，加速了催化气化的工业化进程。     

含羧基/环氧树脂的丙烯酸酯共聚物乳液的制备和交联——1.含羧基丙烯酸酯共聚物乳液的分子设计和制备

以在低温下(<100℃)实现含羧基/环氧树脂的丙烯酸酯共聚物乳液的交联固化为目的,进行了分子设计;估算了共聚物的组成,用碱滴定法测定了乳胶粒表面的羧基数,并比较了不同单体配比所得乳液的成膜性能.     

聚合物驱蚊剂的慢释放研究

本文研究了丙烯酸酯共聚物载体对驱蚊剂N,N-二乙基间甲苯酰胺(DETA)慢释放行为的控制,探讨了单体配比、共聚物分子量以及DETA含量对释放速率的影响。结果表明。增加亲水性单体丙烯酸(AA),可提高DETA的释放速率;降低共聚物数均分子量,会减少DETA的释放量;剂型中DETA含量与释放量存在线性正比关系,但DETA的含量增加并不导致释放有效时间的线性增加。本文还就共聚物膜的透湿性和碱溶性作了研究,亲水性单体AA的增加同样导致透湿性和碱溶性的增加。制备的聚合物驱蚊剂经现场应用试验,表明具有良好的长效驱蚊特性。     

Adsorption and controlled release of Chlortetracycline HCl by using multifunctional polymeric hydrogels

Adsorption and controlled release of Chlortetracycline HCl to and from multifunctional polymeric materials (HEMA/MAA) hydrogels were investigated. P(HEMA/MAA) hydrogels were synthesized by gamma radiation-induced copolymerization of 2-hydroxyethylmethacrylate (HEMA) and methacrylic acid (MAA) in aqueous solution. The influence of copolymer composition and pH value of the surrounding medium on the type of water diffusion into the glassy polymer were discussed. Drug, Chlortetracycline HCl containing hydrogels, with different drug concentration to polymer ratios, was loaded by direct adsorption method. The influence of MAA content in the gel on the adsorption capacities of hydrogel was studied. Chlortetracycline HCl adsorption capacity of hydrogels was found to increase from 8 to 138 mg Chlortetracycline HCl per gram dry gel with increasing amount of MAA in the gel system and drug concentration. The effect of pH on the releasing behavior of Chlortetracycline HCl from gel matrix was investigated. In vitro drug release studies in different buffer solutions show that the basic parameters affecting the drug release behavior of hydrogel are the pH of the solution and MAA content of hydrogel.     

Graft copolymerization of methacrylic acid and acrylamide onto acrylonitrile-butadiene-styrene terpolymer by photoinduced hydroperoxide

Graft copolymerization of methacrylic acid (MAA) or acrylamide (AM) from an aqueous solution onto acrylonitrile-butadiene-styrene terpolymer (ABS) was initiated by the thermal decomposition of polymeric hydroperoxides, which are formed upon UV irradiationof ABS, which contains anthracene. Diffusion of anthracene at room temperature from a methanolic solution into ABS was affected by the acrylonitrile content ofABS.The graft yield was independent on the concentration of anthracene in the wide range of 0.03 X 10^-3 to 14.29 X 10^?3 mol/L in ABS. The graft polymerization reaction does not occur below 100°C.The effect of other variables, such as time of irradiation, intensity of UV, reaction time, and concentration of monomer in aqueous solution, on the amount of monomer grafted to ABS were also investigated.The contact angle significantly decreases upon grafting, indicating that the graft layer is on the surface of the polymer. © 1995 John Wiley & Sons, Inc.     

Synthesis and characterization of nano-sized poly[(butyl acrylate)-co-(methyl methacrylate)-co-(methacrylic acid)] latex via differential microemulsion polymerization

Poly[(butyl acrylate)-co-(methyl methacrylate)-co-(methacrylic acid)] latex particles were synthesized via differential microemulsion polymerization. The effect of initiator type and methacrylic acid incorporation were investigated. The initiator type could significantly affect the particle size and the molecular weight of the resulting polymer and 2,2′-azobisisobutyronitrile produced the smallest particle size. The incorporation of methyl methacrylate (MAA) in the copolymer and terpolymer structures was confirmed by FTIR and NMR spectroscopy, and DSC in that the carbonyl peak of carboxylic acid at 1,700 cm^?1 in the FTIR spectrum was observed when the MAA amount was high enough, the peak areas at 0.9 ppm in the NMR spectrum confirmed the participation of MAA from the increasing proton signals and the glass transition temperature and polarity of the polymer increased when the MAA amount was increased. This supported that the MAA was incorporated into the polymer chains. MAA was found to produce a vitrification effect during the polymerization.     

Interaction of Sodium Dodecyl Sulfate with Poly(ethyleneimine) in Bulk Solution and at the Air-Solution Interface

Interaction of sodium dodecyl sulfate (SDS) with the cationic polyelectrolyte poly(ethyleneimine) (PEI) was investigated in this study. Turbidity measurements were performed in order to analyze the interaction and complex formation in bulk solution as a function of polymer concentration and pH. Surface tension measurements were made to investigate the properties of SDS/PEI/water mixtures at air/solution interface. Results revealed that SDS/PEI complexes form in solution depending on the surfactant and polymer concentration. A decrease was observed in surface tension values in the presence of SDS/PEI mixtures compared to the values of pure SDS solutions. Both solution and interfacial properties exhibited pH dependent behavior. A shift was seen in the critical micelle concentration of SDS solutions as a function of PEI concentration and solution pH. Monovalent and divalent salt additions showed some influence on the interfacial properties of SDS solutions in the presence of PEI.     

羧基氟碳共聚物纤维光催化剂载体的制备与耐光降解

通过溶液聚合法合成了聚(丙烯酸六氟丁酯-co-甲基丙烯酸)(P(HFBA-co-MAA))和聚(甲基丙烯酸十二氟庚酯-co-甲基丙烯酸)(P(DFHMA-co-MAA))羧基氟碳共聚物. 静电纺丝实验结果表明,随着 MAA 用量的减少,两种氟碳共聚物的可纺性逐渐变差,相应的纺丝液的浓度也逐渐降低,所用溶剂的极性和沸点呈现降低的趋势;当配制纺丝液所用低沸点溶剂丁酮用量增大时,所得纤维的直径呈增加趋势;P(DFHMA-co-MAA) 的可纺性优于 P(HFBA-co-MAA). 采用两步法在 P(DFHMA-co-MAA)共聚物纤维表面制备光催化剂 ZnS,XPS 结果表明锌离子先与共聚物纤维表面的羧酸根离子络合,然后络合的锌离子再与硫源 TAA 反应形成 ZnS. MAA 用量高的共聚物纤维表面形成的 ZnS 量与粒子尺寸较大,MAA 用量为 10 wt% 时,共聚物纤维表面形成了纳米级的 ZnS 粒子,通过紫外降解实验和红外分析表明制备的 ZnS/P(DFHMA-co-MAA)纤维复合物具有很好的耐紫外光降解性能.     

pH-responsive non-surface-active/surface-active transition of weakly ionic amphiphilic diblock copolymers

The weakly ionic amphiphilic diblock copolymer polystyrene-b-poly(acrylic acid) was synthesized by nitroxy radical-mediated living radical polymerization with precise control of block length, block ratio, and polydispersity. Systematical surface tension experiments and foam formation observations revealed that this polymer was non-surface active under neutral and alkaline (pH 10) conditions, while it was surface active under an acidic condition (pH 3). This result supports our proposed origin of non-surface activity; the image charge repulsion at the air/water interface is essential in addition to very stable micelle formation in the bulk solution. At a higher pH (pH 12), the polymer showed slight surface activity since the added NaOH played a role as an added salt. The critical micelle concentration (cmc) was estimated by static light scattering. Cmc increased with increasing added salt (NaCl) concentration as was observed for other strongly ionic non-surface-active polymers. Hence, this trend is characteristic for non-surface-active polymers. The pH dependence of cmc was minimum at pH 8–10. Since the acrylic acid block is fully ionized under this condition, the strong image charge repulsion at this condition accelerated micelle formation at a low polymer concentration, which consequently decreased cmc. Micelles in bulk solution were confirmed by dynamic light scattering, and the salt concentration and pH dependencies of the hydrodynamic radius of the micelles were also estimated. The pH-responsive non-surface-active/surface-active transition observed in this study strongly supports the fact that the image charge repulsion is an essential factor for non-surface activity in addition to stable micelle formation in solution.     

Adsorption of polyelectrolyte/surfactant mixtures at the air-solution interface: poly(ethyleneimine)/sodium dodecyl sulfate

Neutron reflectivity and surface tension have been used to characterize the adsorption of the polyelectrolyte/ionic surfactant mixture of poly(ethyleneimine) (PEI) and sodium dodecyl sulfate (SDS) at the air-water interface. The surface tension behavior and adsorption patterns show a strong dependence upon the solution pH. However, the SDS adsorption at the interface is unexpectedly most pronounced when the pH is high (when the polymer is essentially a neutral polymer) and when the polymer architecture is branched rather than linear. For both the branched and the linear PEI polymer/surfactant complex formation results in a significant enhancement of the amount of SDS at the interface, down to surfactant concentrations approximately 10(-6) M. For the branched PEI a transition from a monolayer to a multilayer adsorption is observed, which depends on surfactant concentration and pH. In contrast, for the linear polymer, only monolayer adsorption is observed. This substantial increase in the surface activity of SDS by complexation with PEI results in spontaneous emulsification of hexadecane in water and the efficient wetting of hydrophobic substrates such as Teflon. In regions close to charge neutralization the multilayer adsorption is accentuated, and more extensively ordered structures, giving rise to Bragg peaks in the reflectivity data, are evident.     

Thermosensitive properties of a novel poly(methyl 2-acetamidoacrylate-co-methyl acrylate)

Copolymerizations of methyl 2-acetamidoacrylate (MAA) with methyl acrylate (MA) were carried out at 60 °C in chloroform. MAA-rich copolymers are soluble in water and MAA-poor copolymers insoluble. Among water-soluble copolymers obtained, only one (HP-77) which contains 77% of MAA units was thermosensitive. Thermal properties of HP-77 were investigated in the presence or absence of inorganic salts. The cloud point of aqueous HP-77 solution depended on polymer concentration: The cloud point decreased exponentially with an increasing concentration of the polymer. The cloud point of HP-77 was also affected significantly by the type and concentration of salts. The effectiveness of salts to reduce the cloud point is NaBr≈KBr<NaCl≈KCl<Na₂SO₄≈K₂SO₄. The salting-out coefficients were evaluated as 2.45 l/mol for sodium chloride and 14.56 l/mol for sodium sulfate, respectively, from the relationship (Setschenow's equation) between logarithm of the solubility of HP-77 and salt concentration. The salting-out coefficient of sodium sulfate is larger than that of sodium chloride.     

pH‐responsive ampholytic terpolymers of acrylamide,sodium 3‐acrylamido‐3‐methylbutanoate,and (3‐acrylamidopropyl)trimethylammonium chloride. II. Solution properties

The solution properties of low‐charge‐density ampholytic terpolymers of acrylamide, sodium 3‐acrylamido‐3‐methylbutanoate, and (3‐acrylamidopropyl)trimethylammonium chloride were studied as functions of the solution pH, ionic strength, and polymer concentration. Terpolymers with low charge densities, large charge asymmetries, or both exhibited excellent solubility in deionized (DI) water, and higher charge density terpolymers were readily dispersible in DI water; however, the higher charge density terpolymer solutions separated into polymer‐rich and polymer‐poor phases upon standing over time. Charge‐balanced terpolymers exhibited antipolyelectrolyte behavior at pH values greater than or equal to the ambient pH (6.5 ± 0.2); the same terpolymers behaved increasingly as cationic polyelectrolytes with decreasing solution pH because of the protonation of the 3‐acrylamido‐3‐methylbutanoate (AMB) repeat units. Unbalanced terpolymers generally exhibited polyelectrolyte behavior, although the effects of intramolecular electrostatic attractions (i.e., polyampholyte effects) on the hydrodynamic volume of the unbalanced terpolymer coils were evident at certain values of the solution pH and salt concentration. The dilute‐solution behavior of the terpolymers correlated well with the behavior predicted by several polyampholyte solution theories. In the semidilute regime, solution viscosities increased with increasing terpolymer charge density, and this indicated a significant enhancement of the solution viscosity by intermolecular electrostatic associations. Upon the addition of NaCl, semidilute‐solution viscosities tended to decrease because of the disruption of the intermolecular electrostatic associations. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 3252–3270, 2004     

Thermal behavior of polyacrylonitrile polymers synthesized under different conditions and comonomer compositions

Polyacrylonitrile (PAN) polymers are used as precursors for carbon fiber production. This process requires an oxidative stabilization step, which can be studied by differential scanning calorimetry (DSC). In this sense, thermal behavior of PAN based terpolymers by different polymerization processes, compositions and itaconic acid concentrations in the reaction media were investigated. The obtained results showed that the addition of itaconic acid and methyl acrylate as comonomers resulted a lower heat flow during the process comparing to the PAN homopolymer. It suggested that these comonomers aid the oxidative stabilization stage for all studied process. The redox system polymerization at 40°C resulted in a lower heat flow. Itaconic acid decreases slightly initial and peak temperatures of the terpolymer and heat flow until concentration of 3y. The cyclization temperature decreases when MAis incorporated into the terpolymer compared to the MMA terpolymer and increases when MAA is the acidic monomer. Among terpolymers the AN/MA/AA polymer showed the best thermal behavior for carbon fiber producing.