CL-20/HMX共晶及其为基PBX界面作用和力学性能的MD模拟研究

为提高共晶炸药的实际使用价值, 改善其安全性和力学性能, 以CL-20/HMX共晶炸药为基, 分别添加2种高聚物粘结剂Estane 5703(聚氨基甲酸乙酯)和HTPB(端羟基聚丁二烯), 共构建两种共晶基高聚物粘结炸药(PBX)模型, 进行细致的295 K NPT分子动力学(MD)模拟研究. 通过两种PBX模型及其与该共晶炸药的MD模拟结果比较表明, 与基炸药之间的结合能Estane 5703大于HTPB, 预示含少量Estane 5703的PBX稳定性和相容性更佳; 对相关函数g(r)揭示粘结剂与基炸药界面相互作用的方式, 以基炸药中H分别与Estane 5703中羰基O和HTPB中端羟基O之间的氢键较强. 与CL-20/HMX共晶炸药相比, 少量粘结剂Estane 5703或HTPB的加入, 使弹性系数C_ij下降, 拉伸模量(E)、体积模量(K)和剪切模量(G)均显著减小, 而泊松比(ν), 柯西压(C₁₂－C₄₄)和K/G值明显增大, 表明PBXs体系刚性减小, 延展性增强, 力学性能大为改善. 少量粘结剂包覆使PBXs致钝, 主要归因于其隔热、吸热并使体系变“软”的缓冲作用, 而界面作用造成的分子结构引发键键长变化变为次要因素.     

胶质液体泡沫(CLA)的形成及其稳定性研究

以研究胶质液体泡沫(CLA)内部结构及其特性为最终目的, 对组成为十二烷基醇聚氧乙烯(3)醚(AEO-3)/正癸烷/十二烷基硫酸钠(SDS)/水的CLA体系形成过程和稳定动力学行为进行了电导率测定和光学显微观察. 通过上述两过程的电导率变化探明了CLA的形成和稳定性动力学行为, 并被光学显微照片所证实. 实验结果表明CLA的形成是一个低能量乳化过程, 经历了水相泡沫化→油相替代气泡乳化→CLA形成. 在整个乳化过程中, 没有发生相的转变现象, CLA呈O/W型乳状液. 其稳定性并不遵守一级动力学模型. 在常温下, 其电导率曲线呈直线关系; 当温度超过318.15 K时, 其电导率曲线近似于Langmuir等温线形. 并可用Sigmoidal模型σ_t=(σ₁－σ₂)/[1＋e^(t－t₀)/S] ＋σ₂较好的拟合, 式中, σ_t表示t 时的电导率值(μS/cm); t表示时间(min); σ₁, σ₂分别代表存储过程中电导率最小值和最大值(μS/cm); t₀对应于σ_t等于 1/2(σ₁＋σ₂)的时间t值(min); S描述了电导率曲线陡峭程度(min). 并提出了CLA的破乳过程包括液膜排液和液膜破裂两个阶段, 同时伴随有絮凝过程发生的稳定性机理.     

柚皮苷印迹β-环糊精聚合物的制备及性能研究

以柚皮苷(NG)为印迹分子, β-环糊精为功能体, 六亚甲基二异氰酸酯为交联剂, 采用乳液聚合法制备了对NG具有特定识别能力的吸附材料: 棒状印迹聚合物. 扫描电镜及比表面分析仪测试结果表明印迹聚合物具有较大的孔隙及比表面积|红外及核磁共振谱研究证实了识别位点来自β-环糊精与NG羟基间的氢键作用. 采用平衡吸附实验方法研究了聚合物的吸附性能和选择性能. 实验结果表明, 棒状印迹聚合物(RMIP)对NG具有较高的亲和性和选择性. Scatchard分析表明, MIP在识别NG过程中存在2类结合位点: K_D1＝0.016 mmol/L, B_max1＝15.31 μmol/g, K_D2＝0.24 mmol/L, B_max2＝98.41 μmol/g. 当NG浓度为 0.02 mg/mL时, MIP及相应NIP对 NG的分配系数 K_{D 分别为4.38和2.86, 印迹因子α为1.53.}     

超高效液相色谱塔板高度方程的推导

近年来,分析工作者采用超高效液相色谱(UPLC)完成了许多过去不能完成的分离分析工作。但是在阐述UPLC原理时不少人却采用了van Deemter方程。这是不对的。本文研究了UPLC色谱过程动力学,从热传导方程出发运用色谱动力学原理推导了包括考虑流动相摩擦生热影响的UPLC塔板高度方程H=2γD_m/u+((2λd_pu^1/3)/(u^1/3+ω(D_m/d_p)^1/3))+((2ku)/((1+k)²(1+κ₀)κ_d))+ ((θ(κ₀+κ₀k+k)²d_p²u)/(D_mκ₀(1+κ₀)²(1+k)²)) +(κ_i(κ₀+κ₀k+k)²d_p^5/2u^2/3)/(3κ₀Ω D_m^2/3(1+κ₀)²(1+k)²+(r₀²(κ₀+κκ₀k+k)u)/(4(1+k)D_r)·exp(-Kr₀²α)。上述方程右端最后一项代表了流动相摩擦生热对塔板高度的贡献。当流动相线速度较低时,流动相摩擦生热对塔板高度的贡献趋近于零,塔板高度方程还原成Horvath和Lin的方程;当流动相线速度较高时,由于流动相摩擦生热,柱轴心与边缘温差增加,流动相线速度径向分布差异导致柱效率降低,而柱轴心与边缘的温差与流动相线速度平方成正比。作者明确指出:UPLC的柱效率与柱内径密切相关,采用细内径柱有利于实现高效率;过高的流动相线速度将导致柱效率崩溃。     

供体-锯齿型碳纳米管-受体的非线性光学响应对管径的依赖性

用密度泛函 B3LYP 方法得到一系列不同管径的氨基-硝基双取代纳米管NH₂-(n,0)CNT-NO₂ (n＝5～10)的几何结构. 用CAM-B3LYP 方法计算了体系的第一超极化率(β₀). 研究表明, β₀ 对管径大小有着极强的依赖性. 特别是对偶数纳米管(n＝6, 8 和10), 其β₀ (5.5×10³～9.8×10⁴ au)是奇数纳米管β₀ (1.0×10³～2.8×10³ au)的5～35 倍.     

Tb@C82异构体的分离及其电化学性质研究

通过制备型高效液相色谱分离获得了Tb@C₈₂的两种同分异构体,依据它们的UV-Vis-NIR吸收光谱推断它们分别具有C_2v和C_s对称性的碳笼结构,而且Tb是以+3价的形态内嵌于碳笼中的.电化学研究表明,C₈₂碳笼的对称性对Tb@C₈₂的还原过程的影响较小,而对其氧化过程影响较大.Tb@C₈₂的两种异构体的第一还原电位都比较高,是较好的电子受体材料;而且与Tb@C_2v（9）-C₈₂相比,Tb@C_s（6）-C₈₂氧化还原电位更高一些,说明后者比前者具有更好的接受电子能力.此外,我们观察到了Tb@C_2v（9）-C₈₂的七对可逆的氧化-还原电位,丰富并修正了前人报道的结果.     

4,6-二甲氧基-2-[甲氧脲基硫代脲基]嘧啶的合成、晶体结构和理论计算

利用2-氨基-4,6-二甲氧基嘧啶在干燥条件下与硫氰酸钾、氯甲酸甲酯在乙酸乙酯溶液中反应制得4-(4,6-二甲氧基嘧啶-2-基)-3-硫代脲酸甲酯, 在二甲基甲酰胺溶液中培养出单晶, 通过X射线单晶结构分析法测定分子结构和晶体结构, 晶体属单斜晶系, 空间群为C2/m, 晶胞参数为: a＝1.6672(3) nm, b＝0.66383(12) nm, c＝1.1617(2) nm, β＝109.275(2)°, V＝1.2136(4) nm³, D_c＝1.490 g/cm³, μ＝0.281 mm^－1, F(000)＝568, Z＝4, R₁＝0.0341, wR₂＝0.1042. 运用Gaussian 03程序, 在6-311G的基组水平上, 用HF, MP2以及B3LYP三种计算方法对标题化合物进行了几何全优化, 并对其成键情况及自然键轨道(NBO)进行了分析.     

基于配合物配体策略的Cu-Cd异核配位聚合物的合成与晶体结构

利用小分子配合物[Cu(2-mpac)₂(H₂O)]•3H₂O (1)作为配合物配体, 以其两侧未配位的羰基氧原子与金属配位合成了一个Cu-Cd异核配位聚合物[Cu(2-mpac)₂(H₂O)₂Cd(H₂O)₄(NO₃)₂]_n (2) (2-mpac＝5-methyl-2-pyrazinecarboxylic acid), 并利用元素分析、红外光谱以及X射线单晶衍射法对标题化合物进行了表征. 晶体学数据: 三斜晶系, P-1空间群, a＝0.7654(7) nm, b＝0.8903(8) nm, c＝0.9745(9) nm, α＝116.116(1)°, β＝98.408(1)°, γ＝90.335(1)°, V＝0.5880(9) nm³, Z＝1, S＝1.053, 最终残差因子[I＞2σ(I)] R₁＝0.0280, wR₂＝0.0718, 对于全部数据R₁＝0.0305, wR₂＝0.0741.     

磁场对复配乳化剂/苯胺微乳液聚合体系相行为的影响

首次在酸性条件下, 以十二烷基苯磺酸钠(SDBS)和聚乙二醇辛基苯基醚(TX-100)为复配乳化剂, 制备SDBS/TX-100/正丁醇(nBA)/苯胺(An)/盐酸(HCl)微乳液体系, 并通过该体系的拟三元相图, 考察了恒定磁场(0.4 T)、助表面活性剂(nBA)与复配乳化剂的质量比(K_m＝m_nBA/m_SDBS/TX-100)及SDBS与TX-100的质量比(S_m＝m_SDBS/m_TX-100)对复配乳化剂/苯胺微乳液聚合体系相行为和电导行为的影响. 结果表明: 随着K_m的增加, 微乳区面积先增大后减小, 当K_m＝1.0时, 形成的微乳区面积最大|随着S_m的减少, 微乳区面积逐渐增大|外加磁场可以增大微乳区面积, 且随着S_m的减小, 磁场对微乳液体系的作用逐渐减弱. 循环伏安的测试结果表明, 复合乳化剂微乳液法制备的聚苯胺, 其循环伏安性能优于单组分乳化剂(SDBS或TX-100)微乳液法制备的聚苯胺.     

基于密度泛函理论计算的多氯联苯毒性的定量结构-性质关系研究

多氯联苯(PCBs)是一类人工合成的难降解有机物, 疏水亲油、毒性大, 引起了人们普遍关注. 通过密度泛函理论(DFT)计算获得PCBs 苯环上的负电荷密度(Q)、最低空轨道能量(E_LUMO)、亲电指数(ω)等结构参数, 并分析了PCBs 毒性与其苯环间的共平面性、氯原子取代数(N_Cl)、Q 以及ω 等结构参数之间的关系. 采用SPSS17 统计软件分析了上述结构参数与PCBs 毒性表征量正辛醇-水分配系数(K_OW)的关联度, 并构建lg K_OW 的多元线性回归方程. 采用“交叉检验”方法检验所构建的lg K_OW 定量结构-性质关系(QSPR)方程的稳定性, 并用于预测PCBs 的毒性. 由N_Cl 和ω 构造出的QSPR 方程简单实用、可靠, PCBs 的lg K_OW 计算值与实验结果吻合良好.     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

恶臭嗅辨实验室建设探讨

针对恶臭测试的环境影响问题,提出了解决的实例方案,并对方案的要点及优缺点进行讨论,此方案在实际操作中具有较好的效果。     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.     

Mechanism of action of base-catalyzed oxygenation of phenol derivatives

Cyclopropyl derivative of 2,6-di-tert-butylphenol is synthesized as a probe to investigate the mechanism of base-catalyzed autooxidation of phenol derivatives. Our study indicates that one electron reduction of molecular oxygen from phenolate gives phenoxyl radical 3, a key intermediate of autooxidation. The coupling of phenoxyl radical and superoxide radical gives peroxylate anion 4 and produces the final epoxy alcohol adduct 6.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。