近红外光谱法快速测定溶剂型木器涂料中甲苯、乙苯和二甲苯

建立了使用近红外光谱法(NIR)快速测定溶剂型木器涂料中甲苯、乙苯和二甲苯的方法。收集涂料样品,使用气相色谱法(GC)测定苯系物含量。采用聚乙烯密实袋封装聚氨酯类、硝基类或醇酸类涂料,应用积分球透漫射采样方式采集清漆和漫射采样方式采集色漆的近红外光谱。采用偏最小二乘法,分别建立清漆和色漆的近红外光谱与苯系物线性关系模型。校正集均方差在0.43%~1.32%之间、相关系数R在0.9046~0.9766之间。验证集均方差在0.591%~1.73%之间。对未知样品预测,清漆样品预测值相对偏差<15%;色漆样品预测值相对偏差<20%。两个定量模型预测效果良好。该2个NIR定量方法适用于对溶剂型木器涂料中甲苯、乙苯和二甲苯含量进行快速测定。     

近红外光谱法快速测定涂料固化剂中游离甲苯二异氰酸酯含量

用气相色谱分析值为参照,采用近红外透射光谱（NIR）技术采集相应样品的NIR光谱,研究了涂料固化剂中游离甲苯二异氰酸酯（TDI）含量的快速测定分析方法。 并从120个固化剂样品中挑选出109个代表性的样品建模,选择7320~7250 cm-1和8485~8370 cm-1波段区间,用偏最小二乘法(PLS)和完全交互验证方式建立TDI含量的预测模型。 结果表明,固化剂中游离甲苯二异氰酸酯含量和近红外光谱之间存在较好的相关性,其预测模型的校正集均方差（RMSEC）为0.0815,验证集均方差（RMSEP）为0.0715,模型性能良好。 近红外光谱法可快速准确测定游离甲苯二异氰酸酯（TDI）含量,用于固化剂样品快速分析。     

胆酸含量的近红外分析数学模型

本文应用近红外技术研究了快速测定胆酸含量的方法.通过测定胆酸在10000~4000cm-1范围内的近红外透射光谱,基于偏最小二乘(PLS)算法,建立了胆酸含量的数学模型.以校正均方差(RMSEC)和相关系数(R)为指标,确定了用于建模的最优近红外波段和光谱预处理方法,并基于此模型预测了9个样品.结果显示,建模效果良好,...     

高粱籽粒中多酚类物质的傅立叶变换近红外光谱分析

利用高效液相色谱(HPLC)法测定高粱籽粒中阿魏酸、原儿茶醛和花青素的含量,比色法测定总酚、总黄酮、缩合单宁的含量;运用偏最小二乘法建立NIR光谱与HPLC法和比色法分析值之间的多元校正模型,预测高粱籽粒中主要酚类物质的含量.结果表明,各成分近红外预测值与实测值之间的校正模型相关系数(R)、内部交叉验证均方差(RMSECV)、最佳主因子数分别为:总酚0.9737, 0.288, 4;总黄酮0.9660, 0.00671, 8;缩合单宁0.9558, 0.0289, 6;阿魏酸0.9818, 0.0391, 6;原儿茶醛0.9979, 0.0118, 5;花青素0.9977, 0.0523, 4;预测相对偏差(RSEP)分别为:总酚6.99%、总黄酮4.54%、 缩合单宁7.13%、阿魏酸2.68%、原儿茶醛5.46%、 花青素5.81%.结果表明,模型对样品NIR的预测值与其相应的化学值有较好的相关性,此模型可用来预测高粱籽粒中的各酚类物质的含量,在高粱优质育种和品质分析中具有广泛的应用价值.     

近红外光谱法快速测定柴胡提取过程中的药效成分

利用近红外光谱(NIRS)技术对柴胡提取过程中的药效成分进行快速定量分析。共收集126个柴胡提取液样品,采用紫外-可见分光光度法测定总黄酮和多糖的含量,高效液相色谱法(HPLC)测定柴胡皂苷A及柴胡皂苷D的含量,以透射模式采集提取液的近红外光谱,运用偏最小二乘法(PLS)分别建立了近红外光谱与4种药效指标参考值之间的定量校正模型,并采用不同的预处理方法、光谱波段和主因子数对模型进行优化。结果表明,总黄酮、多糖、柴胡皂苷A和柴胡皂苷D 4种定量模型的近红外预测值与参考值之间的拟合性良好,模型预测精度较高,其中预测集相关系数(RP)均大于0.9;预测集误差均方根(RMSEP)分别为3.46 μg/mL、0.743 mg/mL、1.53 μg/mL、0.406 μg/mL;预测集相对偏差(RSEP)分别为1.65%、8.28%、5.74%、7.52%。该研究证实了NIRS结合PLS可成功应用于监测柴胡提取液中药效成分的含量变化,且方法具有快速、准确、无损和环保的特点。     

近红外光谱快速测定红花逆流提取过程中羟基红花黄色素A的含量

采用近红外光谱(NIRS)透射法对红花罐组式逆流提取过程中羟基红花黄色素A(Hydroxysafflor yellow A,HSYA)的含量进行快速无损的测定.在红花逆流提取过程中,以高效液相色谱法(HPLC)为对照分析方法,测定提取液中羟基红花黄色素A的含量,运用偏最小二乘(PLS)法建立NIR光谱与羟基红花黄色素A的HPLC分析值之间多元校正模型,并对逆流提取过程的未知样本进行含量预测.校正模型相关系数达到0.982,预测相关系数达到0.965,RMSEC和RMSEP分别为0.053和0.075,RSEC和RSEP分别为3.96%和5.25%.结果表明,NIRS可以作为一种准确、快速、无损的检测方法用于检测中药逆流提取过程有效成分含量变化规律.     

近红外光谱法快速测定化橘红中柚皮苷的含量

利用近红外光谱快速测定技术,建立化橘红药材中柚皮苷含量测定模型;用高效液相色谱法(HPLC)测定44批不同产地的化橘红中柚皮苷的含量作为参考值,使用2350～2199 nm、1750～1600 nm和1301～1150 nm波长范围的近红外光谱检测技术,利用偏最小二乘回归分析结合交叉验证法,建立快速测定化橘红中柚皮苷含量的模型;结果表明,所建立的校正模型的相关系数和内部交叉验证均方差分别为:R~2=0.978,RMSECV=0.997,预测结果良好。该法的建立证明了近红外光谱技术应用于化橘红药材中柚皮苷含量测定的可行性;近红外光谱结合偏最小二乘法(NIR-PLS)可以快速评估化橘红药材中柚皮苷的含量,可以应用于大批化橘红药材中柚皮苷的含量测定。     

气相色谱-质谱法测定修正产品中11种苯系物

建立了气相色谱-质谱法同时测定修正产品中11种苯系物(苯,甲苯,乙苯,对-二甲苯,间-二甲苯,邻-二甲苯,苯乙烯,氯苯,1,3-二氯苯,1,4-二氯苯,1,2-二氯苯)含量的检测技术。试样中苯系物经二甲亚砜萃取,经DBWAX型毛细管色谱柱分离,质谱定量。结果表明:11种苯系物在1.0~20.0 mg/kg范围内呈良好的线性关系,相关系数R20.9996;方法检出限在0.04~0.07 mg/kg之间;回收率为89.1%~101.1%,相对标准偏差(RSD)1.5%~4.4%。方法能够满足对修正产品中11种苯系物的分析要求。     

乙醇混合燃料近红外定量分析

采用近红外光谱(NIR)透射法对乙醇混合燃料各成分进行定量分析；其中乙醇体积分数为84．5％～98．2％，汽油体积分数0～15％；通过偏最小二乘法(PLS)建立模型，乙醇含量NIR模型校正集测定系数(R^2)为0．9969，模型校正集标准差(SEE)和预测集标准差(SEP)分别为0．23和0．38，汽油含量NIR模型校正集测定系数为0．9939，模型校正集标准差和预测集标准差分别为0．38和0．39，对含量较小的干扰物质丙酮预测结果也理想；近红外和多元校正技术可作为乙醇混合燃料中成分含量测定简单、快速方法之一。     

近红外光谱法用于木薯燃料酒精品质分析

提出了用近红外光谱法测定木薯燃料酒精中乙醇和水分含量,以确定木薯燃料酒精的品质。结合修正偏最小二乘法建立了样品与其近红外光谱之间的定标模型。结果表明:乙醇定标模型交叉验证均方差和相关系数分别是0.110 2,0.960 5;水分定标模型分别是0.014 3,0.975 9。近红外光谱法预测值与化学分析法的测定值一致,该模型具有很高的预测准确性,可应用于木薯酒精品质分析的快速检测。     

PMDA-BPDA-HAB聚苯并噁唑的合成及耐热性

PMDA-BPDA-HAB聚苯并噁唑的合成及耐热性;均苯四甲酸二酐;联苯四羧酸二酐;二羟基联苯胺;聚酰亚胺;聚苯并噁唑;耐热性     

Synthesis of Some Novel Class of Bis(isoxazoline) and Bis(aziridine) Derivatives

Synthesis of some new bis(isoxazoline) derivatives has been described from terepthaldehyde derived bis(nitrones) using microwave irradiation via 1,3‐dipolar cycloaddition reaction. Bis(isoxazoline) derivatives in turn successfully converted into new bis(aziridine) derivatives via Baldwin rearrangement. Simple reaction methodology, non involvement of catalysts, and good to excellent yields are the important features noticed in this synthesis.     

柴油加氢精制催化剂制备技术

柴油加氢精制催化剂制备技术的发展大致经历了3个阶段,由此形成了三代柴油加氢催化剂:单层分散的负载型金属硫化物催化剂,多层分散的负载型金属硫化物催化剂和非负载型金属硫化物催化剂。本文对金属硫化钼基柴油加氢精制催化剂的应用背景、制备思想及催化剂研究开发现状进行了系统的总结,对柴油加氢催化剂的发展方向进行了展望。     

Magnetism of metal-nitroxide compounds involving bis-chelating imidazole and benzimidazole substituted nitronyl nitroxide free radicals

Coordination compounds based on imidazole and benzimidazole substituted nitronyl nitroxide radicals with transition metal ions and trivalent lanthanide ions are described from the perspective of their magnetic properties.For the transition metal compounds the crystal structures show various metal-nitroxide dimensionalities including mononuclear (0D), one-dimensional (1D) and two-dimensional (2D) complexes. The mononuclear complexes were isolated with most metal ions of the first transition series. One copper(II) complex shows a copper(II)-radical ferromagnetic coupling (J = +75 cm⁻¹) while for the other mononuclear compounds, mainly with manganese(II), the metal-radical interactions are antiferromagnetic. The one-dimensional and two-dimensional complexes are manganese(II) compounds which show canting effects leading to weak ferromagnetism.For the trivalent lanthanide ions [La(III), Gd(III) and Eu(III)], three series of mononuclear complexes were obtained in which the metal center is bound to four, two or one nitroxide radicals depending on the counter ions and ancillary ligands. Unexpectedly, in most gadolinium(III) complexes, the Gd(III)-radical interactions were found to be antiferromagnetic in contradiction with other foundings and previous theoretical models. In support to the magnetic studies, the optical properties of the lantanide complexes have also been investigated and are briefly described.     

Transition metal complexes of the tripodal ligand 4-(2′-pyridylmethyl)-4-azaheptane-1,7-diamine. Crystal structures of [CuLCl]ClO4 and [NiL(MeCN)2](ClO4)2

The tripodal ligand 4-(2′-pyridylmthyl)-4-azaheptane-1,7-diamine has been prepared by reaction of 2-aminemethyl pyridine with acrylonitrile, followed by the reduction of the nitrile groups. Copper(II), nickel(II), zinc(II), cobalt(III) and chromium(III) complexes of the ligand have been prepared and characterized and the crystal structures of the complexes [CuLCl]ClO₄ and [NiL(MeCN)₂](ClO₄)₂ determined. The copper complex is five coordinate with approximate square pyramidal stereochemistry with the apical position occupied by a primary amine donor. The nickel complex is octahedral with the pyridine nitrogen donor lying trans to an acetonitrile ligand.     

The development and application of guidance on equipment qualification of analytical instruments

 This paper describes the development of guidance for the equipment qualification (EQ) of analytical instruments. EQ is a formal process that provides documented evidence that an instrument is fit for its intended purpose and kept in a state of maintenance and calibration consistent with its use.     

Simple,Selective, and Sensitive Spectrophotometric Method for Determination of Trace Amounts of Nickel（Ⅱ）, Copper （Ⅱ）, Cobalt （Ⅱ）, and Iron （Ⅲ） with a Novel Reagent 2-Pyridine Carboxaldehyde Isonicotinyl Hydrazone

A selective and sensitive reagent of 2-pyridine carboxaldehyde isonicotinyl hydrazone（2-PYAINH） was synthesized and studied for the spectrophotometric determination of nickel, copper, cobalt, and iron in detail. At a pH value of 7.0, 9,0, 9.0, and 8.0, respectively, which greatly increased the selectivity; nickel, copper, cobalt, and iron reacted with 2-PYAINH to form a 1：2 yellow-orange, 1：2 yellow-green, 1：2 yellow and 1：1 yellow complexes, with absorption peaks at 363, 352, 346, and 359 nm, respectively. Under the optimal conditions, Beer＇s law was obeyed over the ranges of 0.01-1.4, 0.01-1.5, 0.01-2.7, and 0.01-5.4 mg/L respectively. The apparent molar absorptivity and Sandell＇s sensitivities were 8.4×10^4, 5.2×10^4, 7.1×10^4, and 3.9×10^4 L·mol^-l·cm^-1, respectively, and 0.00069, 0.0012, 0.00078, and 0.0014 μg·cm2, respectively. The detection limits were found to be 0.001, 0.002, 0.003, and 0.01 mg/L, respectively. The detailed study of various interfering ions to make the method more sensitive was carried out and selective and several real samples were analyzed with satisfactory results.     

Electrochemically selective determination of dopamine in the presence of ascorbic and uric acids on the surface of the modified Nafion/single wall carbon nanotube/poly(3-methylthiophene) glassy carbon electrodes

A voltammetric method based on a combination of incorporated Nafion, single-walled carbon nanotubes and poly(3-methylthiophene) film-modified glassy carbon electrode (NF/SWCNT/PMT/GCE) has been successfully developed for selective determination of dopamine (DA) in the ternary mixture of dopamine, ascorbic acid (AA) and uric acid (UA) in 0.1M phosphate buffer solution (PBS) pH 4. It was shown that to detect DA from binary DA-AA mixture, the use of NF/PMT/GCE was sufficient, but to detect DA from ternary DA-AA-UA mixture NF/SWCNT/PMT/GCE was required. The later modified electrode exhibits superior electrocatalytic activity towards AA, DA and UA thanks to synergic effect of NF/SWCNT (combining unique properties of SWCNT such as high specific surface area, electrocatalytic and adsorptive properties, with the cation selectivity of NF). On the surface of NF/SWCNT/PMT/GCE AA, DA, UA were oxidized respectively at distinguishable potentials of 0.15, 0.37 and 0.53 V (vs. Ag/AgCl), to form well-defined and sharp peaks, making possible simultaneous determination of each compound. Also, it has several advantages, such as simple preparation method, high sensitivity, low detection limit and excellent reproducibility. Thus, the proposed NF/SWCNT/PMT/GCE could be advantageously employed for the determination of DA in real pharmaceutical formulations.     

Multi-instrument characterization of HiPIMS and DC magnetron sputtered tungsten and copper films

In this work, copper and tungsten were sputtered onto silicon wafers by direct current magnetron sputtering (DCMS) and high-power impulse magnetron sputtering (HiPIMS). The resulting films were characterized by energy dispersive X-ray spectroscopy (EDX), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), atomic force microscopy (AFM), spectroscopic ellipsometry (SE), and X-ray diffraction (XRD). By EDX and XPS, all the sputtered films showed only the expected metal peaks. By XPS, the surfaces sputtered by DCMS were richer in oxygen than those produced by HiPIMS. By AFM, the surfaces were quite smooth. The root mean square (RMS) roughness values are as follows: 0.83 nm (W, HiPIMS), 1.10 nm (W, DCMS), 0.85 nm (Cu, HiPIMS), and 1.78 nm (Cu, DCMS). By SEM, the HiPIMS films exhibited smaller grain sizes, which was confirmed by XRD. The crystallite sizes estimated by XRD are as follows: 4 nm (W, body-centered cubic, HiPIMS), 13 nm (W, body-centered cubic, DCMS), 7 nm (W, cubic, HiPIMS), 14 nm (W, cubic, DCMS), 25 nm (Cu, HiPIMS), and 35 nm (Cu, DCMS). By SE, the HiPIMS surfaces showed higher refractive indices, which suggested that they were denser and less oxidized than the DCMS surfaces.     

Simultaneous determination of mercury and arsenic by anodic stripping voltammetry

An electrochemical method for the simultaneous determinations of Hg^II concentration and total As^III and As^V concentration has been developed. The method does not require the additional preliminary step of the chemical reduction of As^V to As^III, or oxidation of As^III to As^V before stripping analysis takes place. Also, the method for the simultaneous determination of Hg^II concentration and As^III concentration is described. Measurements were performed in 0.1 M HCl using a gold-plated graphite electrode as sensor. Detection limits for both methods are below 0.4 ppb. Relative standard deviation did not exceed 15%. The possible interference by other trace metals was investigated. Analyses of natural water and industrial solutions were made using proposed methods and AAS. The t-test demonstrates that there was no significant difference between the results obtained with these methods. Proposed methods decrease the time of analysis because concentrations of the Hg^II and arsenic ions were measured simultaneously. Also, the removal of the additional step of chemical reduction of As^V to As^III or oxidation of As^III to As^V decreases analysis time, and also reduces the chance of contamination due to the use of additional reagents.