Ag／TiO2复合纳米催化剂的制备和表征及其光催化活性

 采用光还原沉积贵金属法，制备了Ag／TiO2复合纳米催化剂．通过调节溶液的pH值控制TiO2表面负载银的形貌，利用AAS，XRD，TEM和XPS等手段对样品进行了表征．以苯胺氧化为模型反应，考察了Ag／TiO2复合纳米催化剂样品的光催化活性以及银沉积量和沉积形貌对催化剂活性的影响．结果表明，通过调控光还原沉积条件，可在平均粒径为24nm左右的TiO2颗粒上获得3nm左右均匀分散的银粒子；在TiO2上沉积适量的具有较高分散度的金属Ag，能有效提高TiO2对苯胺氧化反应的光催化活性．     

载体对负载型TiO2催化剂光催化性能的影响

 以活性碳（AC）和镁铝尖晶石（MA）为载体，采用真空吸附水解法制备了负载型光催化剂TiO2／AC和TiO2／MA，并采用TiO2溶胶负载法制备了活性碳负载催化剂TiO2（C）／AC．以氯仿为探针分子研究了其在催化剂上的吸附及光催化降解反应性能．结果表明，催化剂的制备方法、TiO2负载量与载体的吸附性能对光催化活性有明显的影响．通过优化制备条件，TiO2／AC催化剂的催化活性可提高到纳米TiO2的2．5倍．氯仿在AC上的饱和吸附量较高，但吸附强度较弱；在纳米TiO2上的吸附情况则正好相反．氯仿在AC和TiO2上吸附性质的差异有利于吸附在TiO2／AC上的氯仿分子从活性碳载体向TiO2光催化活性中心迁移．镁铝尖晶石载体对光催化反应没有明显的促进作用，与其基本上不吸附氯仿分子有关．与TiO2胶体负载法相比，真空吸附水解法是一种较好的负载型TiO2光催化剂制备方法．     

纳米薄膜光催化剂的制备与表面态研究

利用溶胶-凝胶提拉成膜法制备了TiO2,SnO2,Ag/SnO2,Ag/SnO2/TiO2纳米薄膜半导体催化剂.采用粉末电导法初步研究了纳米半导体薄膜催化剂的表面结构,测定了表面态能级相对于半导体导带边的位置.实验表明:四种催化剂在不同的表面能级位置都存在表面态:TiO2具有两类表面态,其能量分别为0.75eV和0.58eV.Ag/SnO2/TiO2由于Ag的担载,出现更负的表面态能级(0.33eV).这将会显著提高导带电子密度,加速光催化反应速率.     

Au-CuO／TiO2催化剂用于CO2中微量H2的脱除

用沉积沉淀法制备了Au-CuO/TiO2催化剂和Au/TiO2催化剂,考察了沉淀温度、沉淀pH、焙烧温度和Cu/Au摩尔比等制备工艺条件对Au-CuO/TiO2催化剂性能的影响,确定了适宜的催化剂制备工艺条件.结果表明,Au-CuO/TiO2催化剂对CO2中微量H2的脱除具有较好的活性和稳定性.还考察了还原和H2S中毒处理先后的顺序对催化剂H2脱除活性的影响.结果表明,Au/TiO2催化剂基本上不受处理顺序的影响,而H2S处理顺序对Au-CuO/TiO2催化剂的性能有较为明显的影响,这说明还原后的Au-CuO/TiO2催化剂形成了Au-Cu合金。     

TiO2-Al2O3复合氧化物负载NiMo加氢脱硫催化剂的研究

采用溶胶凝胶技术，从Al2O3载体的表面改性出发，制备了TiO2-Al2O3复合载体。采用此改性载体制备了NiMo／TiO2-Al2O3催化剂；用中压固定床微反装置考察了载体改性对制备的催化剂的噻吩加氢脱硫(HDS)活性的影响．用透射电镜、NH3-TPD及吡啶红外光谱法对改性载体和催化剂进行了表征．结果表明，经钛溶胶改性的载体制备的催化剂与原有载体制备的催化剂相比，催化剂活性提高了20％．改性载体表面负载的钛溶胶以纳米尺寸的TiO2微粒形态存在．     

掺杂TiO2纳米粉的合成、表征及催化性能研究

 考察了制备方法对掺杂Fe2O3,ZrO2或SnO2的TiO2纳米粉的XRD谱及催化性能的影响．结果表明,用共沉淀法制备的Fe2O3·TiO2对其XRD谱强度的影响较大,而负载法制备Fe2O3／TiO2对其XRD谱的强度无影响;两种方法制备的掺杂ZrO2或SnO2的TiO2样品对XRD谱均无影响．TEM结果表明,TiO2纳米粉的晶粒均匀,粒径为14～18nm．苯酚水溶液的光催化氧化分解反应结果表明,与TiO2样品相比,负载型Fe2O3／TiO2的催化活性明显较高,但ZrO2／TiO2,SnO2／TiO2和共沉淀型Fe2O3·TiO2的催化活性变化不大．可以认为,对掺杂Fe2O3的TiO2催化剂,负载法是较好的制备方法．     

超临界流体干燥法制备纳米TiO2－ZnO复合催化剂及其对苯酚降解的光催化性能

 以TiCl4和Zn（NO3）2·6H2O为原料，采用溶胶－凝胶法结合超临界流体干燥法制备了纳米级TiO2－ZnO（7～10nm）复合催化剂，并用XRD和TEM等手段进行了表征．以苯酚光催化降解为模型反应对所制备催化剂的催化性能进行了评价．结果表明，与单组分TiO2及普通干燥法制备的TiO2－ZnO催化剂相比较，纳米TiO2－ZnO复合粒子的光催化活性有较大提高．用超临界干燥法制备的催化剂具有粒径小、分布窄、比表面积大、分散性好和光催化活性高等特点．采用超临界流体干燥法可直接制得纳米TiO2（锐钛矿型）－ZnO（非晶态）复合催化剂，可实现干燥、晶化一步完成．复合催化剂中ZnO的最佳掺入量为x（ZnO）＝0．8％．超临界流体干燥法是制备纳米材料的一种新技术，具有产物容易收集和溶剂可回收利用等优点．     

TiO_2分级结构/Ag_3PO_4复合材料的可见光催化性能

制备了具有分级结构的海胆状TiO2纳米材料,并通过原位沉积法将可见光响应的Ag3PO4纳米颗粒沉积到TiO2的纳米分级结构上,合成了具有高效稳定可见光催化性能的系列TiO2分级结构/Ag3PO4复合材料,对比测试了系列材料对罗丹明B(RhB)的光催化降解性能.结果表明,TiO2分级结构/Ag3PO4复合材料光催化性能明显高于纯相的Ag3PO4光催化剂,同时也明显优于TiO2(P25)/Ag3PO4复合光催化剂,其中分级结构TiO2与Ag3PO4摩尔比为1∶1的复合材料具有最强的光催化性能,在可见光照射6min内可实现RhB的完全脱色.分析结果表明,与纳米颗粒TiO2相比,具有海胆状纳米结构的TiO2可为Ag3PO4的负载提供更多的担载位点,增加TiO2和Ag3PO4的接触面积,进而提升Ag3PO4光激发产生的光生电子-空穴的分离效率.同时在光降解过程中,Ag3PO4表面存在的少量Ag+会逐渐还原成单质Ag0,通过Ag0的等离子体共振效应,可增加对光子的吸收转换能力,从而进一步提高该复合材料光催化降解染料的性能.     

金属离子掺杂的TiO2薄膜的制备及其光催化降解甲苯的性能

 采用溶胶-凝胶法制备了负载于铝板上掺杂金属离子的TiO2薄膜光催化剂,并通过空气中甲苯光催化降解实验评价了其光催化活性. 结果表明,Pt和Fe的掺杂对TiO2薄膜的光催化活性起促进作用,甲苯降解率分别提高了17%和6%; Ag的掺杂引起催化剂失活; Mn的掺杂未对TiO2薄膜的光催化活性起明显促进作用. XRD结果表明,掺杂金属离子前后TiO2均为锐钛矿相; TEM观察到薄膜催化剂微观结构为球形颗粒,粒径分布均匀,平均粒径为19 nm; 紫外漫反射光谱表明,Pt-TiO2薄膜催化剂的反射率几乎为0,表明其对光的吸收能力很强,因而Pt掺杂的TiO2薄膜光催化降解甲苯的活性最高.     

贫燃条件 In-Ag/TiO2-γ-Al2O3催化 CO选择性还原NO

汽车尾气中主要污染成分 CO和 NOx可导致酸雨、光化学烟雾和臭氧空洞效应,对生物、环境及生态系统造成重大危害。污染源中 CO是性能优良的还原剂,如能不添加还原剂实现 CO催化还原 NOx,将成为最具经济技术优势的 NOx脱除技术。在富氧、低温条件下,利用 CO选择性催化还原 NOx为 N2,是目前选择性催化还原研究中的热点和难点。催化 CO还原 NOx常用的贵金属 Ir, Rh, Pt和Pd矿藏稀少,价格昂贵,有氧条件下活性急降,而分子筛催化剂和一些金属氧化物催化剂普遍存在反应温度高,尤其对 N2选择性差等问题。为解决上述问题,需寻找新的适合我国矿产资源的催化体系。研究发现,稀散金属基催化剂对氮氧化物的净化具有一定效果,因而可将我国的稀散金属资源优势转化为技术优势和经济优势。因此,本文以 TiO2-γ-Al2O3(TA)为载体, In/Ag为活性组分,采用等体积浸渍法制备了 InAg/TA以及 In/TA, Ag/TA和InAg/Al (γ-Al2O3为载体)催化剂,考察了贫燃条件下 CO选择性还原NO的催化活性。研究表明,双金属催化剂InAg/Al和 InAg/TA的活性比单金属催化剂In/TA和 Ag/TA高, In/TA催化剂中引入 Ag物种能降低起燃温度;另外,相比于InAg/Al催化剂, InAg/TA催化剂具有较高的催化活性,550?600°C时 N2产率超过60%,说明载体中引入TiO2可以提高催化剂活性。为了深入研究 InAg/TA催化剂中 Ag物种和TiO2对 In物种的作用,通过比表面测定、X射线衍射(XRD)、透射电子显微镜(TEM)、X射线光电子能谱、紫外-可见光吸收光谱、氢气程序升温还原、傅立叶变换红外线光谱等方法分析了催化剂结构和表面形态。结果表明, Ag物种可以提高 In物种的分散性, In和 Ag物种在 TA载体表面可以很好地分散,从而有利于提高催化活性。 In和 Ag物种在 TA载体表面以氧化态形式存在,并且 Ag物种可以提高 In物种表面含量,表面 In和 Ag物种含量越高,吸附活性位越多,催化活性越高;同时, TiO2也可以促进 NO吸附,从而提高 InAg/TA催化剂活性。 InAg/TA催化剂在450°C连续反应72 h进行稳定性测试,测试前后分别在50?600°C进行活性测试,并用 XRD和 TEM对反应后的催化剂进行表征测试。结果表明, InAg/TA催化剂具有较好的稳定性,连续反应前后催化剂活性基本保持不变,推测可能由于在有 CO和O2存在的体系中, Ag物种利用自身 Ag+与 Ag0之间的氧化还原反应抑制了活性组分 In2O3的还原和聚集,稳定了 In物种乃至催化剂活性。 InAg/TA催化剂用于贫燃条件下CO还原NO具有较好的催化效果,主要归因于催化剂活性组分分散性好,稳定性高,对NO吸附能力强。 Ag物种可以稳定In物种并提高其分散性, TiO2可以改善In物种和Ag物种的分散性并促进NO吸附。     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

恶臭嗅辨实验室建设探讨

针对恶臭测试的环境影响问题,提出了解决的实例方案,并对方案的要点及优缺点进行讨论,此方案在实际操作中具有较好的效果。     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.     

Mechanism of action of base-catalyzed oxygenation of phenol derivatives

Cyclopropyl derivative of 2,6-di-tert-butylphenol is synthesized as a probe to investigate the mechanism of base-catalyzed autooxidation of phenol derivatives. Our study indicates that one electron reduction of molecular oxygen from phenolate gives phenoxyl radical 3, a key intermediate of autooxidation. The coupling of phenoxyl radical and superoxide radical gives peroxylate anion 4 and produces the final epoxy alcohol adduct 6.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。