有机官能化介孔硅基材料负载纳米金催化剂的制备及其催化性能

一步合成了桥键嵌入二硫醚官能化介孔硅基材料(PMO-SBA-15),利朋介孔硅基材料孔道内表面的二硫醚基团捕获纳米金(Au)粒子的作用,获得了负载型纳米Au催化剂(Au-PMO-SBA-15).小角X射线衍射和低温N2吸附-脱附的结果表明,PMO-SBA-15和Au-PMO-SBA-15均保持典型的介孔结构;高分辨透射电镜观察到纳米Au粒子在载体孔道内分散均匀,甲均粒径为(2.2±0.2)nm.以70%的叔丁基过氧化氧水溶液为氧化剂,考察了纳米Au催化剂Au-PMO-SBA-15在苯甲醇氧化反应中的催化性能.结果表明,当反应温度为353 K、反应时间为5 h时,苯甲醇的转化率为29.1%,苯甲醛的选择性为100%,且催化剂重复使用7次其催化活性和苯甲醛选择性基奉不变.     

SiO_2负载Au-Pd双金属纳米颗粒催化甲醇选择性氧化合成甲酸甲酯（英文）

甲醇选择氧化制备甲酸甲酯(MF)是延伸甲醇产业链、开发高附加值下游产品的有效途径之一,负载型Au及Pd催化剂在这一反应中表现出优异的低温催化性能。为探索实用、高效和易再生的甲醇选择氧化催化剂,同时揭示双金属颗粒中Au和Pd的协同效应及甲醇氧化反应机理,本研究制备了一系列二氧化硅负载的Au-Pd催化剂(Au-Pd/SiO2),详细研究了其对甲醇选择氧化制甲酸甲酯的催化性能。结果表明,Au和Pd总负载量为0.6%、且Au/Pd质量比为2时,所制备的Au2-Pd1/SiO2催化剂表现出优异的甲醇氧化催化性能;在130℃下,甲醇转化率达到57.0%,MF选择性为72.7%。多种表征结果显示,Au-Pd双金属纳米颗粒粒径为2-4 nm,高度分散于SiO2载体表面,倾向于生成孪晶结构并暴露(111)晶面,这些因素是AuPd/SiO2具有优异催化性能的主要原因。通过DRIFTS表征研究,提出了一个可能的MF生成机理:即甲醇首先与处于Au-Pd纳米粒子界面的表面氧作用,生成化学吸附的甲氧基;随后,甲氧基经去质子作用生成吸附的甲醛物种,后者与相邻的甲氧基物种亲核反应,并经β-H消除后得到目标产物MF。     

尺寸可控、高热稳定性有序介孔碳Au催化剂的合成

纳米Au催化剂被认为是具有商业价值的用于醇选择氧化的第二代催化剂.这是因为Au氧化还原电势高,化学稳定性好,可抑制易使Pt族元素中毒的胺等的毒化;其次,对于一些特定选择氧化和还原反应而言,具有较优的反应选择性.目前较多的研究集中在调变Au纳米颗粒与氧化物载体的相互作用,获得协同效应.例如,利用CeO2纳米晶为载体,沉积Au纳米颗粒(约3 nm),使CeO2部分还原为非计量比的催化材料,活化氧并获得高选择氧化性能.碳是相对惰性的载体,与Au相互作用力弱,因此可被用于研究Au纳米颗粒本征催化性能.但负载碳金催化剂在焙烧甚至还原过程中易团聚,且在反应中易流失,可能导致活性下降.利用胶体沉积法可获得介孔碳担载纳米Au催化剂,对葡萄糖选择氧化具有很高的催化活性和选择性.但是,制备中使用的保护剂残留经常被忽略.由于立体效应或电子结构调变作用,保护剂可能影响Au催化剂活性或稳定性.我们前期建立了反应单体参与的自组装技术合成功能化介孔碳路线,一步在介孔碳骨架中掺杂氧化物纳米催化剂.本文从介孔催化材料的结构出发,设计“镶嵌”在碳骨架中的纳米Au颗粒.采用配位作用辅助表面活性剂自组装技术,以苯酚和甲醛为碳前体,引入含巯基硅烷偶联剂,通过配位作用稳定金离子,获得尺寸可控介孔碳限域纳米Au催化剂.低温炭化中,由于巯基-金的配位作用阻抑金属移动或团聚,高温下聚合物炭化为相对刚性的碳骨架.此时,Au纳米颗粒被相邻介孔孔墙限制.硅烷偶联剂可除去,不影响碳载体,并可产生丰富二级孔道,获得多级孔道介孔碳材料.X射线衍射和透射电镜结果显示,所合成的催化剂中Au颗粒的尺寸可控,为3-18nm,且具有单分散性,均匀地分散在整个介孔碳骨架中,其含量为1.1-9.0 wt％.金碳催化剂具有有序的二维六方介孔结构.能量散射谱(EDX)也证明了催化剂只含有C,O和Au元素,没有S和Si元素的残留.X射线光电子能谱(XPS)结果显示催化剂表面的Au含量远远低于ICP的测试结果,也证明了Au纳米颗粒分布在介孔碳骨架内,同时只含有C,O和Au元素也与EDX相符.X射线近边吸收谱结果表明,随着颗粒尺寸的减小,Au表面电子性质发生改变.N2吸脱附等温线显示,有序介孔碳金催化剂具有典型的第Ⅳ型曲线,说明孔径分布范围较窄,主孔道尺寸为3.4-5.7 nm.值得注意的是,低压力段吸附量显示明显突跃,暗示其具有一套约为2 nm的次级介孔.所有的催化剂都具有高的比表面积(1269-1743 m2/g)和大的孔体积(0.79-1.38 cm3/g).Au纳米颗粒具有高的热稳定性,在惰性气氛中,即使在600℃也未见明显聚集长大.进一步讨论了合成中影响金纳米颗粒尺寸的重要影响因素.(1)巯基含量:通过调节巯基组分的含量,可以调控催化剂中Au纳米颗粒的尺寸(9-18 nm).需要强调的是,Au纳米颗粒尺寸与巯基在新合成材料中的浓度有关,当巯基含量在所研究的范围中时(1.55-3.06 mmol/g),Au纳米颗粒尺寸仅仅与巯基浓度有关,而与Au浓度无关.(2)硫酸预炭化处理:新合成的材料经过一步硫酸预炭化处理,可以得到尺寸为3 nm的有序介孔碳金催化剂.表征结果证明,经过硫酸预碳化处理,大量表面活性剂被除去,同时聚合物载体发生部分碳化,有助于在后续高温炭化中保护3 nm金颗粒不团聚.尺寸可控、高热稳定性、无配体保护的有序介孔碳负载Au催化剂有望应用在催化和传感器等领域.     

尺寸可控、高热稳定性有序介孔碳Au催化剂的合成（英文）

纳米Au催化剂被认为是具有商业价值的用于醇选择氧化的第二代催化剂.这是因为Au氧化还原电势高,化学稳定性好,可抑制易使Pt族元素中毒的胺等的毒化;其次,对于一些特定选择氧化和还原反应而言,具有较优的反应选择性.目前较多的研究集中在调变Au纳米颗粒与氧化物载体的相互作用,获得协同效应.例如,利用CeO_2纳米晶为载体,沉积Au纳米颗粒(约3 nm),使CeO_2部分还原为非计量比的催化材料,活化氧并获得高选择氧化性能.碳是相对惰性的载体,与Au相互作用力弱,因此可被用于研究Au纳米颗粒本征催化性能.但负载碳金催化剂在焙烧甚至还原过程中易团聚,且在反应中易流失,可能导致活性下降.利用胶体沉积法可获得介孔碳担载纳米Au催化剂,对葡萄糖选择氧化具有很高的催化活性和选择性.但是,制备中使用的保护剂残留经常被忽略.由于立体效应或电子结构调变作用,保护剂可能影响Au催化剂活性或稳定性.我们前期建立了反应单体参与的自组装技术合成功能化介孔碳路线,一步在介孔碳骨架中掺杂氧化物纳米催化剂.本文从介孔催化材料的结构出发,设计"镶嵌"在碳骨架中的纳米Au颗粒.采用配位作用辅助表面活性剂自组装技术,以苯酚和甲醛为碳前体,引入含巯基硅烷偶联剂,通过配位作用稳定金离子,获得尺寸可控介孔碳限域纳米Au催化剂.低温炭化中,由于巯基-金的配位作用阻抑金属移动或团聚,高温下聚合物炭化为相对刚性的碳骨架.此时,Au纳米颗粒被相邻介孔孔墙限制.硅烷偶联剂可除去,不影响碳载体,并可产生丰富二级孔道,获得多级孔道介孔碳材料.X射线衍射和透射电镜结果显示,所合成的催化剂中Au颗粒的尺寸可控,为3-18nm,且具有单分散性,均匀地分散在整个介孔碳骨架中,其含量为1.1-9.0wt%.金碳催化剂具有有序的二维六方介孔结构.能量散射谱(EDX)也证明了催化剂只含有C,O和Au元素,没有S和Si元素的残留.X射线光电子能谱(XPS)结果显示催化剂表面的Au含量远远低于ICP的测试结果,也证明了Au纳米颗粒分布在介孔碳骨架内,同时只含有C,O和Au元素也与EDX相符.X射线近边吸收谱结果表明,随着颗粒尺寸的减小,Au表面电子性质发生改变,N_2吸脱附等温线显示,有序介孔碳金催化剂具有典型的第Ⅳ型曲线,说明孔径分布范围较窄,主孔道尺寸为3.4-5.7nm.值得注意的是,低压力段吸附量显示明显突跃,暗示其具有一套约为2 nm的次级介孔.所有的催化剂都具有高的比表面积(1269-1743m~2/g)和大的孔体积(0.79-1.38cm~3/g).Au纳米颗粒具有高的热稳定性,在惰性气氛中,即使在600℃也未见明显聚集长大.进一步讨论了合成中影响金纳米颗粒尺寸的重要影响因素.(1)巯基含量:通过调节巯基组分的含量,可以调控催化剂中Au纳米颗粒的尺寸(9-18nm).需要强调的是,Au纳米颗粒尺寸与巯基在新合成材料中的浓度有关,当巯基含量在所研究的范围中时(1.55-3.06mmol/g),Au纳米颗粒尺寸仅仅与巯基浓度有关,而与Au浓度无关.(2)硫酸预炭化处理:新合成的材料经过一步硫酸预炭化处理,可以得到尺寸为3 nm的有序介孔碳金催化剂.表征结果证明,经过硫酸预碳化处理,大量表面活性剂被除去,同时聚合物载体发生部分碳化,有助于在后续高温炭化中保护3nm金颗粒不团聚.尺寸可控、高热稳定性、无配体保护的有序介孔碳负载Au催化剂有望应用在催化和传感器等领域.     

SiO2负载Au-Pd双金属纳米颗粒催化甲醇选择性氧化合成甲酸甲酯

甲醇选择氧化制备甲酸甲酯（MF）是延伸甲醇产业链、开发高附加值下游产品的有效途径之一,负载型Au及Pd催化剂在这一反应中表现出优异的低温催化性能。为探索实用、高效和易再生的甲醇选择氧化催化剂,同时揭示双金属颗粒中Au和Pd的协同效应及甲醇氧化反应机理,本研究制备了一系列二氧化硅负载的Au-Pd催化剂（Au-Pd/SiO₂）,详细研究了其对甲醇选择氧化制甲酸甲酯的催化性能。结果表明,Au和Pd总负载量为0.6%、且Au/Pd质量比为2时,所制备的Au₂-Pd₁/SiO₂催化剂表现出优异的甲醇氧化催化性能;在130℃下,甲醇转化率达到57.0%,MF选择性为72.7%。多种表征结果显示,Au-Pd双金属纳米颗粒粒径为2-4 nm,高度分散于SiO₂载体表面,倾向于生成孪晶结构并暴露（111）晶面,这些因素是Au-Pd/SiO₂具有优异催化性能的主要原因。通过DRIFTS表征研究,提出了一个可能的MF生成机理：即甲醇首先与处于Au-Pd纳米粒子界面的表面氧作用,生成化学吸附的甲氧基;随后,甲氧基经去质子作用生成吸附的甲醛物种,后者与相邻的甲氧基物种亲核反应,并经β-H消除后得到目标产物MF。     

纳米Au/TS-1催化剂的制备及用于甲醇羰基化体系

采用负压沉积沉淀法、等体积浸渍法、负压等体积浸渍法等方法制备了纳米Au/TS-1催化剂,研究了深床焙烧和等离子体焙烧,以及焙烧温度和焙烧气氛对催化剂中纳米金粒子大小和催化性能的影响,并采用ICP、TEM、XRD、UV-vis、XPS对催化剂金粒子进行了物化性能表征,采用甲醇羰基化制乙酸甲酯反应表征催化性能.结果表明,不同制备方法、不同焙烧方法、不同焙烧温度和焙烧气氛对负载型纳米Au/TS-1沸石分子筛催化剂中金粒子的大小、形貌、物化性质和催化性能有明显影响.其中,3种制备方法中,氢气气氛下焙烧均比空气和氮气气氛下焙烧得到的催化剂的金粒子尺寸更小,分散更均匀,约为5~10 nm.与其它方法相比,负压沉积沉淀法可制得分散更均匀的金粒子,Au/TS-1沸石催化剂中的金粒子尺寸更小,平均粒径为1~5 nm.催化性能评价结果显示,3种方法制备出的负载型金催化剂用于催化甲醇羰基化制乙酸甲酯反应体系中,甲醇的转化率分别为85%、75%、60%,乙酸甲酯选择性可高达68%,反应温度200℃为最好.     

超稳纳米金催化剂—走在实用化的路上

纳米金的催化性能受载体影响巨大,选择合适的载体或设计金属-载体界面精细结构能显著影响纳米金的催化性能.迄今发现各种载体包括酸、碱金属氧化物、碳材料以及有机聚合物均可作为纳米金的有效载体.相应的各种金催化剂均展现出独特的催化活性与选择性.一个典型的例子是核壳结构的Au/NiO催化剂,基于该催化剂催化异丁烯醛制备异丁烯酸甲酯的化工厂己于2008年开始兴建.金催化剂在AsH3气体传感器和汞收集器等环境分析方面也开始实际应用.因而,金催化剂的稳定性和使用寿命成为当前关注的焦点问题.目前报道的长寿命金催化剂典型例子有MINTEK催化剂和YD-3烟台催化剂,后者是由α-Fe2O3和La2O3改性氧化铝负载的金催化剂.中国科学院大连化学物理研究所张涛院士和王军虎研究员团队在近期研究中发现高温焙烧条件下Au纳米颗粒与羟基磷灰石(HAP)载体之间会发生金属-载体强相互作用(Strong Metal-Support Interaction简称SMSI)效应.SMSI效应导致载体对Au纳米颗粒形成包裹,可以有效提升Au纳米颗粒的抗烧结性能,但其对活性位的覆盖也会导致催化剂活性的下降.最近,该团队通过向载体HAP中添加TiO2进行修饰,成功设计开发出Au/HAP-TiO2催化剂.该催化剂上Au纳米颗粒与HAP接触的一侧被HAP薄层包裹,与TiO2接触的一侧裸露,呈现出独特的半包裹结构.通过这种纳米尺度的结构设计,该金催化剂经过8000℃的高温焙烧后不仅对一系列反应均表现出可观的催化活性和优异的抗烧结性能,且在模拟汽车尾气CO消除反应中表现出优于商业三效催化剂的反应稳定性.该工作为负载型纳米金催化剂的应用,特别是在高温催化反应中的实际应用提供了新途径,因此有望促进负载型金催化剂的实用化乃至商业化进程.     

无碱条件下Au/ZnO选择性催化氧化1,3-丙二醇合成3-羟基丙酸甲酯

采用溶胶-沉积法合成了高选择性的Au/ZnO催化剂,用于1,3-丙二醇选择性氧化酯化为3-羟基丙酸甲酯的反应.研究了保护剂PVA用量、金溶胶合成温度、金负载量及催化剂循环利用对反应的影响,且优化了反应温度和反应压力,并对催化剂进行了XRD和TEM表征.结果表明,PVA∶Au(m/m)=1∶4、金溶胶合成温度25℃、金负载量1%的Au/ZnO对目标反应的催化活性最好,在100℃和Po2=2MPa的条件下1,3-丙二醇的转化率达82.8%,产物3-羟基丙酸甲酯的选择性达95.4%.Au纳米粒子的粒径影响催化性能,在Au平均粒径为2.8~6.1nm的范围内,产物选择性随Au纳米粒子的粒径的减小而增大,平均粒径在2.8~4.8nm的范围内时,催化剂具有较好的产物选择性(大于90%);Au/ZnO催化剂循环利用4次后催化性能(转化率和选择性)无明显下降;并推测了无碱条件下Au/ZnO选择性催化氧化1,3-丙二醇合成3-羟基丙酸甲酯的反应机制.     

Au/TiO2催化剂制备条件对巴豆醛选择加氢的影响

采用沉积-沉淀法制备了纳米Au/TiO2催化剂, 以X射线衍射(XRD)、透射电子显微镜(TEM)、X射线光电子能谱(XPS)等手段对催化剂进行了系统的表征, 并考察了该催化剂在巴豆醛液相加氢制巴豆醇反应中的催化性能. 通过改变活化气氛、负载量和还原温度, 能够调节Au粒子的尺寸及金属与载体间的相互作用. 在673 K还原条件下制备Au质量分数为9.2%的Au/TiO2 催化剂上, Au粒子的平均粒径为2 nm, 初始加氢速率达到13.7×10-5 mol·s-1·g-1, 同时巴豆醇最高收率可达69.9%. 结合表征结果, 该催化剂良好的巴豆醛选择加氢性能归属为载体TiO2在还原条件下产生的氧缺陷位对Au纳米粒子的锚定作用及给电子作用.     

CeO2对抗烧结Au₲MgGa2O4催化剂用于水汽变换和催化燃烧反应的促进作用

自上世纪八十年代在多相催化研究领域兴起纳米金催化淘金热以来,负载型纳米金催化剂的优越性和局限性都得到了广泛的研究.负载型纳米金催化剂活性强烈依赖于其晶粒尺寸和载体性质,一般认为,金纳米颗粒只有在一定的尺寸范围(2-5 nm)且负载在"活性"载体表面才能发挥出其优异的催化活性.然而,小尺寸纳米金颗粒热稳定性差的弱点阻碍了其工业化应用的进程.因此,如何实现小尺寸金纳米颗粒的高温稳定以及构筑金与"活性"载体间有效的接触界面是发挥纳米金优异催化性能的关键.我们曾利用MgGa_2O_4尖晶石载体与金纳米颗粒形成金属-氧化物"异质孪晶"结构,从而实现了将～3 nm的金颗粒稳定在块体金的熔点(1064°C)以上,为小尺寸纳米金的高温稳定提供了新的思路.但MgGa_2O_4尖晶石是一种非氧化还原性载体,对水分子或氧气分子的辅助活化作用较弱,因而限制了具有优异高温抗烧结性能的Au?MgGa_2O_4催化剂在水汽变换和催化燃烧反应中的应用.本文采用等体积浸渍法在高温800°C焙烧5 h后的Au?MgGa_2O_4-800℃-5h样品上进行CeO_2助剂的修饰,以提高其对水分子和氧气分子的活化能力.利用STEM, XRD和EDS-Mapping表征对CeO_2/[Au?MgGa_2O_4-800°C-5h]样品进行结构分析,发现该样品中纳米Au具有优异的高温抗烧结性能, 800°C焙烧5 h并经CeO_2修饰后其颗粒尺寸仍保持在3.1 nm左右,样品中CeO_2的晶粒尺寸约为6 nm,且Au纳米颗粒与CeO_2助剂间形成了有效的接触界面.利用H_2-TPR和XPS表征对该样品的氧化还原性能及电子性质进行分析,发现CeO_2/[Au?MgGa_2O_4-800°C-5h]样品中CeO_2的还原温度相比于CeO_2/MgGa_2O_4对比样品显著降低, XPS结果显示CeO_2添加后Au的化学价态由金属态变为氧化态,表明Au与CeO_2助剂间具有显著的电子转移.同时, CeO_2的添加显著提高了800°C老化后Au?MgGa_2O_4催化水汽变换(CO转化率由～1.5%升到～34.0%, 450°C)、甲烷燃烧(T50降低80°C)和CO氧化(T50降低100°C)等反应活性.为理解CeO_2对Au?MgGa_2O_4的催化性能促进机制,我们选取水汽变换反应为例,利用DRIFTs表征发现CeO_2促进了反应物H_2O的活化,并结合小尺寸Au对CO的活化能力,从而使水汽变换反应顺利进行.本文在MgGa_2O_4尖晶石稳定纳米金的基础上,利用具有优异氧传输性能的CeO_2作为助剂,提高了该催化剂对水分子和氧气分子的活化能力,从而获得了对水汽变换反应和催化燃烧反应具有高稳定性和高活性的CeO_2/[Au?MgGa_2O_4]催化剂.这种"先稳定-后活化"的催化剂设计思路也为今后高稳定性、高催化活性的纳米金催化剂的设计和制备提供了借鉴.     

Molecularly Imprinted Polyresorcinol Based Capacitive Sensor for Sulphanilamide Detection

A molecularly imprinted polymer (MIP) based capacitive sensor for antibiotic detection in drinking water and milk has been developed on a gold coated silicon electrode (Au Electrode). The electrode was fabricated by electropolymerizing monomer resorcinol (RN) on Au surface in presence of sulphanilamide (SN) as a template molecule, to get insulated RN polymer antibiotic composite. The insulation of the polymer film was improved by incubation of electrode in 1‐Dodecanethiol solution. Subsequently MIP sensor was obtained by extraction of SN in ethanol and acetic acid solution. Electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV) measurements were performed for characterization of the developed MIP electrode at different steps of fabrication. The surface morphology of MIP electrode was characterized using atomic force microscopy (AFM), X‐ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive x‐ray spectroscopy (EDS). Performance of MIP sensor was evaluated by measuring change in capacitance against varying concentration of SN using EIS. A linear response in the range 1 to 200 μg L^?1 SN was recorded for MIP sensor with a detection limit of 0.1 μg L^?1. The developed MIP sensor exhibited good selectivity towards SN in water and milk with recoveries in the range 92 % to 105 %. The obtained results suggest the usability of MIP based sensor for SN estimation in water and milk samples.     

分子印迹聚合物修饰电化学晶体管检测抗坏血酸分子

以抗坏血酸(AA)为模板分子、邻苯二胺(o-PD)为功能单体,在金电极表面电聚合制备分子印迹聚合物膜(MIP),并以该MIP修饰的电极为栅极制备了具有高选择性、高灵敏度的AA电化学晶体管(OECT)传感器件。应用循环伏安法(CV)、交流阻抗法(EIS)对分子印迹聚合物电极进行一系列的表征与检测。实验结果表明:以pH=5.2,浓度为0.2mol/L HAc-NaAc(体积比2.1∶7.9)的缓冲液为背景溶液,o-PD与AA的物质的量之比为1∶2,以0.5V/s的扫描速率在0~0.8V内扫描20圈,所得分子印迹膜电极性能最佳。应用以该分子印迹修饰电极作为栅极的电化学晶体管检测AA,得到AA浓度的检测限为0.3μmol/L,沟道电流与AA浓度在0.3~3μmol/L(低浓度)与3~100μmol/L(高浓度)这2个范围内成线性关系。     

Acetylsalicylic acid electrochemical sensor based on PATP-AuNPs modified molecularly imprinted polymer film

A novel electrochemical sensor based on molecularly imprinted polymer film has been developed for aspirin detection. The sensitive film was prepared by co-polymerization of p-aminothiophenol (p-ATP) and HAuCl(4) on the Au electrode surface. First, p-ATP was self-assembled on the Au electrode surface by the formation of Au-S bonds. Then, the acetylsalicylic acid (ASA) template was assembled onto the monolayer of p-ATP through the hydrogen-bonding interaction between amino group (p-ATP) and oxygen (ASA). Finally, a conductive hybrid membrane was fabricated at the surface of Au electrode by the co-polymerization in the mixing solution containing additional p-ATP, HAuCl(4) and ASA template. Meanwhile, the ASA was spontaneously imprinted into the poly-aminothiophenol gold nanoparticles (PATP-AuNPs) complex film. The amount of imprinted sites at the PATP-AuNPs film significantly increases due to the additional replenishment of ASA templates. With the significant increasing of imprinted sites and doped gold nanoparticles, the sensitivity of the molecular imprinted polymer (MIP) electrode gradually increased. The molecularly imprinted sensor was characterized by electrochemical impedance spectroscopy (EIS), differential pulse voltammetry (DPV), and cyclic voltammetry (CV). The linear relationships between current and logarithmic concentration were obtained in the range from 1 nmol L(-1) to 0.1 μmol L(-1) and 0.7 μmol L(-1) to 0.1 mmol L(-1). The detection limit of 0.3 nmol L(-1) was achieved. This molecularly imprinted sensor for the determination of ASA has high sensitivity, good selectivity and reproducibility, with the testing in some biological fluids also has good selectivity and recovery.     

Preparation of molecularly imprinted polymer by surface imprinting technique and its performance for adsorption of dibenzothiophene

The novel surface imprinted polymer composites (MIP/K(2)Ti(4)O(9)) were prepared using dibenzothiophene (DBT) as the template, 4-vinylpyridine as the functional monomer and potassium tetratitanate whisker (K(2)Ti(4)O(9)) as the carrier. The synthetic product was characterized by Fourier transform infrared spectroscopy and scanning electron microscopy. Parameters influencing DBT adsorption such as contact time, temperature and DBT initial concentration were investigated. The adsorption kinetics were evaluated with the pseudo-first-order and pseudo-second-order models, and the adsorption isotherms were fitted by Langmuir and Freundlich models. Selectivity experiments showed that MIP/K(2)Ti(4)O(9) exhibited excellent recognition capacity and binding affinity to DBT compared with the comparative substrates. MIP/K(2)Ti(4)O(9) could also be easily regenerated and reused ten times with only about 20% loss of adsorption capacity.     

Molecularly Imprinted Polymer Thin Film Based Surface Plasmon Resonance Sensor to Detect Hemoglobin

Molecularly imprinted polymer（MIP） films for hemoglobin detection were prepared onto the Au/Cr coated surface plasmon resonance（SPR） sensor chips by the in situ electropolymerization of 3-aminophenylboronic acid（3-APBA）.The formation of the films and rebinding processes of hemoglobin were monitored by in situ electrochemical-SPR（EC-SPR） spectroscopy,with allowed real-time observation of the simultaneous changes in electrochemical and optical properties of the films.Scanning electron microscopy（SEM） and atomic force microscopy（AFM）were used to characterize the surface morphologies of the MIP films.The effects of pH,ion strength,different metal ions on rebinding Hb,the specific binding and the selective recognition were investigated.The results obtained with the molecular imprinted SPR chips indicate a good adsorption of Hb in a range of 0.0005-5 mg/mL in 0.05 mol/L sodium phosphate buffer at pH=7.0.A linear calibration curve（R2=0.94） of the SPR sensor for Hb detection was obtained in a range of 0.05-5 mg/mL.The detection limit for hemoglobin by this method was 0.000435 mg/mL（S/N=3）.Interference studies indicate that the MIP films have a good selectivity compared with the referenced proteins.The stability of the sensor was also established.Results indicate that the SPR sensor chip keeps 87.6％ of its original response after 14 d of storage under dry and ambient conditions.     

Electrochemistry of Os(2,2'-bpy)2ClPyCH2NHCOPh tethered to Au electrodes by S-Au and C-Au junctions

Osmium pyridine-bipyridine redox centers have been tethered to Au electrodes by chemical modification through Au-S and Au-C bonds respectively. 4-Mercapto benzoic acid and the reduction product of the aryl diazonium salt of 4-amino benzoic acid were reacted on Au surfaces, with further post-functionalization by chemical reaction of the osmium complex amino-pyridine derivative with the surface carboxylates. The resulting modified Au surfaces were characterized by polarization modulated infrared reflection absorption spectroscopy (PM-IRRAS), scanning tunneling microscopy (STM), X-ray photoelectron spectroscopy (XPS), resonant raman spectroscopy and cyclic voltammetry.     

Ternary Ag/Polyaniline/Au nanocomposites: Preparation,characterization and electrochemical properties

Ternary Ag/Polyaniline/Au nanocomposites were synthesized successfully by immobilizing of Au nanoparticles (NPs) on the surface of Ag/Polyaniline (PANI) nanocomposites. Ag/PANI nanocomposites were prepared via in situ chemical polymerization of aniline in the presence of 4-aminothiophenol (4-ATP) capped silver colloidal NPs. Then, uniform gold (Au) NPs were assembled on the surface of resulted Ag/PANI nanocomposites through electrostatic interaction to get Ag/Polyaniline/Au nanocomposites. The nanocomposites were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), energy-dispersive X-ray spectroscopy (EDX), ultraviolet visible spectroscopy (UV-Vis), thermogravimetric analysis (TGA) and Fourier transform infrared spectroscopy (FTIR). Moreover, Ag/PANI/Au nanocomposites were immobilized on the surface of a glassy carbon electrode and showed enhanced electrocatalytic activity for the reduction of H₂O₂ compared with Ag/PANI.     

Electrochemical sensors based on molecularly imprinted polymers grafted onto gold electrodes using click chemistry

We have developed a three-step method to graft molecularly imprinted polymer (MIP) thin films onto Au electrodes. In the first step, propargyl acrylate is clicked onto an azidoundecanethiol (N(3)(CH(2))(11)SH)/decanethiol mixed self-assembled monolayer (SAM). Then, by applying UV light (365 nm) in the presence of N,N'-methylenebis(acrylamide) (MAAM) and azobisisobutyronitrile (AIBN) as the radical initiator, polymerization was carried out directly on the electrode surface in the presence of an electroactive template molecule, hydroquinone (HQ). Detection of HQ using the clicked-on MIP sensor was studied using chronoamperometry and its behavior was compared to that of a sensor prepared by drop-coating MIPs onto Au. The detection limit of the clicked-on MIP sensor for HQ was found to be 1.21±0.56 μM, about four times lower than what was observed using the coated-on MIP sensor. In addition, the sensitivity of the clicked-on MIP sensor was found to be approximately three times greater than the coated-on MIP sensor. Apparent diffusion coefficients determined using chronoamperometry suggest that the improved performance is likely due to the favorable mass transfer characteristics of the clicked-on MIP sensing membrane.     

Preparation of erythromycin imprinted polymer by metal-free visible-light–induced ATRP and its application in sensor

Journal of Solid State Electrochemistry - Erythromycin (ERY) molecular imprinted polymer was prepared on the surface of Au electrode modified with Ni and Au nanoclusters (MIP/AuNCs/Ni/Au) via...     

新型乙基溴硫磷印迹膜/纳米金化学修饰电极的研制及应用

以恒电位将金纳米粒子(AuNP)沉积于玻碳电极表面,在模板分子乙基溴硫磷存在下通过循环伏安法将L-半胱氨酸组装到金纳米粒子修饰的玻碳电极上,制备了可选择性识别乙基溴硫磷的L-Cys/ AuNP/ GCE印迹膜电极.结果表明,该电极具有良好的稳定性和重现性,对乙基溴硫磷的线性响应范围为2.5 ～17.5μmol/L,检出...