功能化石墨烯/聚苯胺复合电极材料的制备和电化学性能

利用水合肼还原十八胺(ODA)接枝的氧化石墨烯(GO),得到了十八胺功能化石墨烯(ODA-G),将ODAG与聚苯胺(PANI)通过溶液共混法,制备了功能化石墨烯和聚苯胺纳米复合材料(ODA-G/PANI).采用傅里叶变换红外(FTIR)光谱、X射线衍射(XRD)、热重分析(TGA)、拉曼(Raman)光谱及透射电镜(TEM),对复合材料的结构和形貌进行了表征;利用循环伏安、恒流充放电及交流阻抗谱等,对复合材料的电化学性能进行了测试.结果显示,少量ODA-G的引入为PANI的电化学氧化还原反应提供了更多的电子通道和活性位置,有利于提高PANI的赝电容.在电流密度1.0 A·g-1下,2%(w)ODA-G/PANI的比电容达到787 F·g-1,而相应的PANI仅有426 F·g-1.此外,ODA-G/PANI的循环稳定性也远高于纯PANI.     

RAFT聚合制备PBMA/AA-SiO2杂化纳米材料

以三硫代二[4-(甲氧羰基)苄基]碳酸酯为链转移剂(CTA),甲基丙烯酸丁酯(BMA)为单体,通过可逆加成-断裂链转移自由基聚合(RAFT)法修饰丙烯酸(AA)功能化的纳米二氧化硅(SiO2),制备了PBMA/AA-SiO2有机/无机杂化纳米材料。并通过FT-IR、GPC、TGA、TEM表征和分析了杂化材料的结构、分子量、SiO2纳米粒子在基体中的分散性以及杂化材料的热稳定性。结果表明,PBMA/AA-SiO2杂化微球粒径约为22 nm,分布均匀;TGA分析表明此杂化材料的热稳定性良好,PBMA接枝率为19%。     

聚吡咯/氧化石墨烯层状复合材料的制备及其在超级电容器中的应用(英文)

通过将吡咯单体在低温下与氧化石墨烯进行原位聚合,获得聚吡咯/石墨烯(Ppy/CRGO)复合材料.采用场发射电子显微镜(FESEM)、红外(FT-IR)和热重分析(TGA)对复合物的表面形貌、结构进行表征.FESEM结果表明,通过控制氧化石墨烯(GO)和吡咯单体的质量比例,可以对复合物的层状和厚度进行调控.FT-IR和TGA结果表明,聚吡咯(Ppy)是通过化学键合的方式与氧化石墨烯复合在一起.通过机械冷压法将粉末状Ppy/CRGO复合物压成圆片电极,并探讨了石墨烯和聚吡咯复合比例、反应时间、烘干温度和孔隙率等因素对Ppy/CRGO复合物电极的电学和电化学性能的影响.结果表明,Ppy与CRGO质量比为10∶1所制得的Ppy/CRGO复合物的电容量为421 F·g-1,通过在电极中引入孔隙,电容量能进一步提升为509 F·g-1.     

Fe3O4磁性纳米粒子-氧化石墨烯复合材料的可控制备及结构与性能表征

首先利用高温分解法制备了粒径为18 nm的Fe₃O₄磁性纳米粒子, 并进行羧基化修饰, 然后与聚乙烯亚胺(PEI)化学修饰的氧化石墨烯进行交联反应, 得到磁功能化的氧化石墨烯(MGO)复合材料. 研究了氧化石墨烯片上的磁性纳米粒子的可控负载及其对复合材料磁性能的影响. 利用透射电子显微镜(TEM), 原子力显微镜(AFM), X射线衍射(XRD), 傅里叶变换红外(FT-IR)光谱, 热重分析(TGA), 振荡样品磁强计(VSM)等手段对MGO复合材料的形貌, 结构和磁性能进行了表征. 结果表明, 我们发展的MGO复合材料的制备方法具有简单、可控的优点, 所制备的MGO复合材料具有较高的超顺磁性. 该类磁性氧化石墨烯复合材料有望在磁靶向药物、基因输运、磁共振造影以及磁介导的生物分离和去除环境污染物等领域获得广泛的应用.     

乙醇胺功能化石墨烯的制备与表征

乙醇胺在温和条件下与氧化石墨烯反应, 然后经水合肼还原得到功能化的石墨烯. 干燥的功能化石墨烯经超声处理后, 可稳定分散于水、乙醇、丙酮和N,N二甲基甲酰胺(DMF)等溶剂中. 原子力显微镜(AFM)、透射电镜(TEM)分析表明功能化石墨烯平均厚度为3～4 nm. 傅里叶变换红外光谱(FTIR)、X射线光电子能谱(XPS)、X射线衍射(XRD)对功能化石墨烯的结构分析表明: 乙醇胺与氧化石墨烯发生了化学反应, 并通过共价键连接到石墨烯的六元环上. TG结果表明功能化石墨烯的热稳定性比氧化石墨烯有所提高, 但低于还原氧化石墨烯.     

氧化石墨烯/PMMA和表面官能化的石墨烯/PMMA复合材料的制备及其力学性能的研究

使用简单的溶液共混的方法制备了氧化石墨烯/聚甲基丙烯酸甲酯(GO/PMMA)和表面官能化的石墨烯/聚甲基丙烯酸甲酯复合材料.通过透射电镜(TEM),扫描电镜(SEM)和原子力显微镜(AFM)观察了石墨烯及复合材料的表观形貌.通过拉伸实验表征了其力学性能,研究发现随着石墨烯的加入,其拉伸强度和断裂伸长率都有所改善,而且表面官能化的石墨烯的复合材料的改善效果要优于氧化石墨烯.     

甲基丙烯酸缩水甘油酯功能化石墨烯的制备与表征

利用改进的Hummers法对天然鳞片石墨进行氧化处理制备氧化石墨烯,将其与甲基丙烯酸缩水甘油酯(GMA)在温和条件下反应,再经水合肼还原得到功能化石墨烯.分散性测试结果表明,超声后的功能化石墨烯可以稳定分散于丙酮、乙醇和N,N-二甲基甲酰胺等有机溶剂中.采用傅里叶变换红外光谱、X射线衍射分析及X射线光电子能谱对样品的结构进行了表征.结果表明,GMA上的环氧基与氧化石墨烯上的羟基发生了化学反应,键合在氧化石墨烯表面;经水合肼还原后,层间距较功能化氧化石墨烯缩小,无序度增加.扫描电子显微镜(SEM)测试结果表明,功能化石墨烯含大量褶皱和卷曲;原子力显微镜(AFM)测试结果表明,功能化石墨烯的厚度为2~3 nm.热重分析结果表明,还原氧化石墨烯的热稳定性最高,功能化石墨烯次之,氧化石墨烯的热稳定性最低.     

KH-570功能化石墨烯的制备与表征

采用Hummers法对天然石墨进行氧化处理制备了氧化石墨烯,通过γ-甲基丙烯酰氧丙基三甲氧基硅烷与氧化石墨烯反应得到功能化氧化石墨烯,然后在水合肼的作用下制备了功能化石墨烯。未烘干的功能化石墨烯在超声处理下,能稳定分散在体积比为9∶1(V/V)的乙醇/水、丙酮/水或N,N-二甲基甲酰胺/水的混合溶剂中。用傅立叶变换红外光谱、原子力显微镜、X射线光电子能谱及X射线衍射对样品结构、形貌进行了分析。结果表明,KH-570上的硅氧烷与氧化石墨烯上的羟基发生了反应,经水合肼还原后,功能化石墨烯的无序度增加,层间距也比功能化氧化石墨烯的缩小了。功能化石墨烯在DMF/水中呈高度剥离状态,片层厚度为1.1～2.3 nm。     

功能化石墨烯/聚苯胺复合电极材料的制备和电化学性能

利用水合肼还原十八胺（ODA）接枝的氧化石墨烯（GO）,得到了十八胺功能化石墨烯（ODA-G）,将ODAG与聚苯胺（PANI）通过溶液共混法,制备了功能化石墨烯和聚苯胺纳米复合材料（ODA-G/PANI）. 采用傅里叶变换红外（FTIR）光谱、X射线衍射（XRD）、热重分析（TGA）、拉曼（Raman）光谱及透射电镜（TEM）,对复合材料的结构和形貌进行了表征;利用循环伏安、恒流充放电及交流阻抗谱等,对复合材料的电化学性能进行了测试. 结果显示,少量ODA-G的引入为PANI 的电化学氧化还原反应提供了更多的电子通道和活性位置,有利于提高PANI 的赝电容. 在电流密度1.0 A·g^-1下,2%（w）ODA-G/PANI 的比电容达到787 F·g^-1,而相应的PANI 仅有426 F·g^-1. 此外,ODA-G/PANI的循环稳定性也远高于纯PANI.     

通过“点击化学”对石墨烯和氧化石墨烯进行功能化改性

点击化学具有操作简单方便、灵活高效等特点,在石墨烯的功能化改性上具有极其重要的应用.本工作针对点击化学对石墨烯和氧化石墨烯功能化改性方面进行了综述.将石墨烯点击功能化改性方法分为两种情况:共价键结合的点击功能化改性和非共价键作用的点击功能化改性,其中共价键结合又可细分为边缘点击功能化改性和表面点击功能化改性.首先,本工作对石墨烯点击功能化改性的反应过程和反应条件及其研究方法作了详细的归类和系统的总结.一方面,在石墨烯点击功能化改性的分类上包括:氧化石墨烯边缘点击,氧化石墨烯表面点击,石墨烯表面点击,石墨烯表面经过Diels-Alder[4+2]的点击反应,以及通过非共价键作用的π-π堆积之后的点击反应;另一方面,在点击反应的合成路线上,详细列出了对石墨烯或者氧化石墨烯进行炔基化或者叠氮基化以及功能化分子进行相应地叠氮基化或者炔基化的连接方法和反应条件,通过点击反应将两部分连接起来,并指出石墨烯功能化复合物的功能特性和应用前景.对这部分工作进行列表总结,然后作图列出石墨烯和氧化石墨烯的点击功能化反应的具体分类和反应过程.另外,本工作列表总结了IR,Raman,UV,1H NMR,13C NMR,XPS,XRD,AFM,TEM,SEM,CV,TGA等对石墨烯和氧化石墨烯进行表征的常用方法,指出了常见的出峰位置以及表征结果和测试目的,并作了简要的分析和说明.最后,对点击化学在石墨烯和氧化石墨烯上的功能化应用作出了总结和展望.     

Simultaneous determination of phenolic acids and flavonoids in rice using solid-phase extraction and RP-HPLC with photodiode array detection

An analytical method based on an optimized solid-phase extraction procedure and followed by high-performance liquid chromatography (HPLC) separation with diode array detection was developed and validated for the simultaneous determination of phenolic acids (gallic, protocatechuic, 4-hydroxy-benzoic, vanillic, caffeic, syringic, p-coumaric, ferulic, sinapic, and cinnamic acids), flavanols (catechin and epicatechin), flavonols (myricetin, quercetin, kaempferol, quercetin-3-O-glucoside, hyperoside, and rutin), flavones (luteolin and apigenin) and flavanones (naringenin and hesperidin) in rice flour (Oryza sativa L.). Chromatographic separation was carried out on a PerfectSil Target ODS-3 (250 mm × 4.6 mm, 3 μm) column at temperature 25°C using a mobile phase, consisting of 0.5% (v/v) acetic acid in water, methanol, and acetonitrile at a flow rate 1 mL min(-1) , under gradient elution conditions. Application of optimum extraction conditions, elaborated on both Lichrolut C(18) and Oasis HLB cartridges, have led to extraction of phenolic acids and flavonoids from rice flour with mean recoveries 84.3-113.0%. The developed method was validated in terms of linearity, accuracy, precision, stability, and sensitivity. Repeatability (n = 5) and inter-day precision (n = 4) revealed relative standard deviation (RSD) <13%. The optimized method was successfully applied to the analysis of phenolic acids and flavonoids in pigmented (red and black rice) and non-pigmented rice (brown rice) samples.     

Droplet microfluidics based microseparation systems

Lab on a chip (LOC) technology is a promising miniaturization approach. The feature that it significantly reduced sample consumption makes great sense in analytical and bioanalytical chemistry. Since the start of LOC technology, much attention has been focused on continuous flow microfluidic systems. At the turn of the century, droplet microfluidics, which was also termed segmented flow microfluidics, was introduced. Droplet microfluidics employs two immiscible phases to form discrete droplets, which are ideal vessels with confined volume, restricted dispersion, limited cross-contamination, and high surface area. Due to these unique features, droplet microfluidics proves to be a versatile tool in microscale sample handling. This article reviews the utility of droplet microfluidics in microanalytical systems with an emphasize on separation science, including sample encapsulation at ultra-small volume, compartmentalization of separation bands, isolation of droplet contents, and related detection techniques.     

乙酸镍吡啶配合物催化的分子氧氧化反应研究

Ni(OAc)2结合吡啶和叔丁基过氧化氢(TBHP)实现了苄基C-H与苄基醇类化合物在温和条件下(80～90℃,O21 atm)的选择性催化分子氧氧化反应.研究了过氧化物添加剂,配体,溶剂和温度的影响,得到了优化的反应条件.在苄基C-H的氧化中显示了很高的酮/醇选择性.用ESR法进行了Ni(III)的检测,证实了反应机理.竞争实验说明羰基化合物的生成不是因为醇继续氧化.酮可被解释为过氧化氢中间体受金属催化分解的产物.     

Changes in the proteome of extracellular vesicles shed by rat liver after subtoxic exposure to acetaminophen

To identify changes in extracellular vesicles (EVs) secreted by the liver following drug-induced liver injury (DILI), rats were treated with a subtoxic dose (500 mg/kg) of the analgesic drug, acetaminophen (APAP). EVs were collected by liver perfusion of sham and APAP-treated rats. Changes in EVs morphology were examined by transmission electron microscopic analysis of negatively stained vesicles. Results from morphometric analysis of EVs revealed striking differences in their size and distribution. Proteome composition of EVs collected by liver perfusion was determined by mass spectrometry using methods of sample preparation that enabled better detection of both highly hydrophobic proteins and proteins with complex post-translational modifications. The collection of EVs after liver perfusion is an approach that enables the isolation of EVs shed not only by isolated hepatocytes, but also by the entire complement of hepatic cells. EVs derived after DILI had a lower content of alpha-1-macroglobulin, ferritin, and members of cytochrome 450 family. Fibronectin, aminopeptidase N, metalloreductase STEAP4, integrin beta, and members of the annexin family were detected only in APAP-treated samples of EVs. These results show that the present approach can provide valuable insights into the response of the liver following drug-induced liver injury.     

Paternal genetic structure of Kyrgyz ethnic group in China revealed by high-resolution Y-chromosome STRs and SNPs

Kyrgyz ethnic group is one of the nomads in China, with the majority in Xinjiang and a small part of them living in Heilongjiang province. Historically, they have went through five migrations westward due to the wars. The name “Kyrgyz” means 40 tribes, originating from the primary groups of Kyrgyz. However, it is a largely understudied population, especially from the Y chromosome. In this study, we used a previously validated high-resolution Y-chromosome single nucleotide polymorphisms (Y-SNPs) and short tandem repeats (Y-STRs) system to study Kyrgyz ethnic group. A total of 314 male samples of Kyrgyz ethnic group were genotyped by 173 Y-SNPs and 27 Y-STRs. After data analysis, the results unveiled that Kyrgyz ethnic group was a population with high percentage of both haplogroup C2a1a3a1d∼-F10091 (91/134) and R1a1a1b2a2-Z2124 (109/134), which has never been reported. This implied that Kyrgyz ethnic group might have gone through bottleneck effects twice, with these two main lineages left. Mismatch analysis indicated that the biggest mismatch number in haplogroup C2a1a3a1d∼-F10091 was 10, while that of haplogroup R1a1a1b2a2-Z2124 was 20. This huge difference reflected the different substructure in two lineages, suggesting that haplogroup C2a1a3a1d∼-F10091 might have the least admixture compared to the other two lineages. After admixture modelling with other datasets, the conclusion could be drawn that Kyrgyz ethnic group had great genetic affinity with Punjabi from Lahore, Pakistan, which supported that Kyrgyz ethnic group in China was close to central Asian.     

TPD study of NH3 adsorption/desorption on the surface of V/Ti, V/Al based catalysts for selective catalytic reduction of Nox by ammonia 2. TPD test of commercial V/W/Ti, V/Al, Pd/V/Al catalysts

The effect of temperature on the adsorption/desorption of ammonia from the air mixture on the surface of commercial binary V/Al and ternary Pd/V/Al, V(0.65 wt.%) /W(6.73 wt.%) /Ti and V(1.8 wt.%) /W(7.3 wt.%) /Ti de-NO_x catalysts has been investigated by temperature-programmed desorption (TPD) method. The ability of the commercial catalysts to adsorb ammonia in the most stable surface species was shown to correlate well with their suppression of the NH₃ oxidation.     

Electroosmotic flow: From microfluidics to nanofluidics

Electroosmotic flow (EOF), a consequence of an imposed electric field onto an electrolyte solution in the tangential direction of a charged surface, has emerged as an important phenomenon in electrokinetic transport at the micro/nanoscale. Because of their ability to efficiently pump liquids in miniaturized systems without incorporating any mechanical parts, electroosmotic methods for fluid pumping have been adopted in versatile applications—from biotechnology to environmental science. To understand the electrokinetic pumping mechanism, it is crucial to identify the role of an ionically polarized layer, the so-called electrical double layer (EDL), which forms in the vicinity of a charged solid–liquid interface, as well as the characteristic length scale of the conducting media. Therefore, in this tutorial review, we summarize the development of electrical double layer models from a historical point of view to elucidate the interplay and configuration of water molecules and ions in the vicinity of a solid–liquid interface. Moreover, we discuss the physicochemical phenomena owing to the interaction of electrical double layer when the characteristic length of the conducting media is decreased from the microscale to the nanoscale. Finally, we highlight the pioneering studies and the most recent works on electro osmotic flow devoted to both theoretical and experimental aspects.     

Simultaneous liquid-liquid extraction of dibenzyl disulfide, 2,6-di-tert-butyl-p-cresol, and 1,2,3-benzotriazole from power transformer oil prior to GC and HPLC determination

2,6-Di-tert-butyl-p-cresol (DBPC), dibenzyl disulfide (DBDS), and 1,2,3-benzotriazole (BTA) are additives that may be found concomitantly in the oil matrix of power transformer. DBPC and DBDS act as antioxidants while, BTA is a corrosion inhibitor that protects copper conductors inside the transformer unit from corrosion. A powerful analytical method is, therefore, required to determine these additives at trace levels in the transformer oil. This work describes a unique single liquid-liquid extraction pretreatment step prior to the determination of the components by gas chromatography (GC) and high-performance liquid chromatography (HPLC) techniques. The optimum volume ratio used in the pretreatment step was determined as 5:2:5 for mineral oil/n-hexane/acetonitrile, respectively. Relatively, the method is simple and quick with a minimal use of solvents. Analytical results indicate that the method is relatively sensitive, accurate, and precise for each of the three components in fresh and used mineral oil. The calibration curves for the three components demonstrate a significant increase in sensitivities. Detection limits found were, 100 mg L(-1) (0.01% w/v), 0.80 mg L(-1) , and 2.04 mg L(-1) for DBPC, DBDS, and BTA, respectively. The Student's t values determined at 95% confidence level indicate that there is no significant difference between the experimental means obtained by this method and the standard method for each component.     

Analysis of alendronate in human urine and plasma by magnetic solid-phase extraction and capillary electrophoresis with fluorescence detection

A simple, rapid and sensitive CE-fluorescence (FL) detection method for the analysis of alendronate (ALEN), a bisphosphonate drug, has been developed. Using a buffer solution of 20 mM sodium phosphate (pH 10.0) and a voltage of 24 kV, separation of ALEN in a 55-cm length (35-cm effective length) capillary was achieved in 5 min. FL detection of ALEN was performed via pre-column derivatization with 2,3-naphthalene dicarbox-yaldehyde (NDA). Linear correlation (r=0.9981, n=6) between FL intensity and analyte concentration was obtained in the range of 7-200 ng/mL ALEN. The developed CE-FL method was applied to the analysis of ALEN in human urine and plasma samples. In order to eliminate the interfering matrix components, SPE using magnetic Fe(3) O(4) @Al(2) O(3) nanoparticles as solid sorbents was employed to clean the biological fluids before CE-FL analysis. The linear ranges of ALEN in urine and plasma were 5-100 ng/mL (r = 0.9982, n = 7) and 5-70 ng/mL (r = 0.9954, n = 7), respectively. The LOD and LOQ in both urine and plasma samples were 1.5 and 5 ng/mL ALEN, respectively. Total analysis time including sample pre-treatment and CE separation was less than 1.5 h.     

盐酸氯丙嗪在聚L-苏氨酸/多壁碳纳米管修饰电极上的电化学行为

以玻碳电极为基底成功制备了聚L-苏氨酸poly(L-Threonine)/多壁碳纳米管(MCNTs)修饰电极(p-L-Thr/ MCNTs/GCE).研究了盐酸氯丙嗪在该修饰电极上的电化学行为.该修饰电极对盐酸氯丙嗪具有明显的电催化氧化作用,并对此电极进行显微表征.本研究将此修饰电极用于流动注射不可逆双安培(FL-IB)体系的构建,即利用盐酸氯丙嗪在p-L-Thr/MCNTs/GCE上的氧化和高锰酸钾(KMnO4)在另一支铂电极上的还原构建了双安培检测体系,成功的建立了在外加电压为0 V条件下流动注射双安培法直接测定盐酸氯丙嗪的方法.在0 V外加电压下,在1 mol/L pH6.8的磷酸盐缓冲溶液的载液中,氧化峰峰电流与盐酸氯丙嗪浓度在2.0×10-6mol/L～4.0×10-5 mol/L范围内呈良好的线性关系,其线性回归方程为i (nA)=9.73×107C-50(r=0.9993,n=6),在4.0×10-5mol/L～10-3 mol/L范围内呈线性关系,其线性回归方程为i (nA)=2.33×107C+4×103 (r=0.9984,n=7),方法检出限为4.0×10-7 mol/L (S/N=3).连续测定1.00×10-4mol/L的盐酸氯丙嗪标准溶液20次,电流值RSD为2.44%,进样频率为90样/h.该方法具有较高的选择性和灵敏度.对盐酸氯丙嗪片中的盐酸氯丙嗪的含量的测定,结果比较满意.