Ni-Cu/Al_2O_3催化剂上顺酐液相选择加氢制丁二酸酐反应性能

以Al2O3为载体,采用等体积浸渍法制备了一系列Ni-Cu/Al2O3催化剂,用于顺酐液相加氢反应,并结合低温N2物理吸-脱附、H2程序升温还原、H2程序升温脱附、X射线衍射、CO程序升温表面反应等表征结果,详细考察了催化剂中Cu含量对其催化性能的影响.结果表明,Cu的引入提高了活性组分Ni的分散度,促进了催化剂上C=C的加氢活性;同时,由于Ni-Cu双金属间的相互作用,明显抑制了催化剂表面C=O的加氢.当Cu含量为7%时,催化剂上顺酐加氢定向合成丁二酸酐的活性最高.在210oC,H2压力5.0MPa的条件下反应40min时,顺酐转化率与丁二酸酐选择性均达100%.     

煅烧温度对Mn/TiO_2催化剂催化NO氧化活性的影响

以浸渍在二氧化钛上的锰基催化剂为对象,研究了制备过程中煅烧温度对锰基催化剂催化NO氧化活性的影响。结果表明,较低的煅烧温度有利于提高Mn/TiO2催化剂对于NO氧化的催化效率。利用X射线粉末衍射(XRD)、场发射扫描电子显微镜(FESEM)、X射线光电子能谱(XPS)、H2程序升温还原(H2-TPR)和O2程序升温脱附(O2-TPD)等表征手段研究了煅烧温度影响Mn/TiO2催化剂催化活性的作用机理。结果表明,在NO氧化过程中发挥主要作用的是Mn2O3,较低的煅烧温度有利于提高Mn2O3在锰氧化物中所占的比例,同时增加锰氧化物在载体表面的分散度,从而改善催化剂活性;当煅烧温度超过500℃时,催化剂会发生烧结,载体TiO2的晶形开始由锐钛型向金红石型转变,Mn2O3也从非晶相向晶相转变。H2-TPR和O2-TPD测试结果表明,低温煅烧有利于提高催化剂的还原性能和表面化学吸附态O2-的脱附性能,良好的还原性能和脱附性能的相互作用使催化剂表面的氧有较好的移动能力,从而促进催化剂的活性。     

载体对负载型NiSn催化剂丙烷脱氢性能的影响

研究了载体对负载型Ni Sn催化剂丙烷脱氢性能的影响,主要对比考察了以Si O2、Mg O、Al2O3、Mg Al2O4为载体的Ni Sn催化剂的丙烷脱氢性能。采用X射线衍射技术(XRD)、氮气吸附-脱附技术、氨气程序升温脱附技术(NH3-TPD)以及氢气程序升温还原技术(H2-TPR)对催化剂样品进行表征。结果表明,Si O2因具有较大的比表面积、大孔径、酸性较弱等特点,以其为载体制备所得催化剂中Ni2.67Sn2组分含量高,催化剂性能较高。     

热解二氧化钛/聚苯胺制备高效非贵金属氧还原电催化剂

为了克服传统Pt系催化剂价格昂贵、稳定性差的缺点,采用热解新型Ti O2/聚苯胺(PANI)复合物的方法合成了Ti O2/C催化剂.用扫描电子显微镜、X射线光电子能谱、X射线衍射、傅里叶变换红外光谱、拉曼光谱、透射电子显微镜、循环伏安法和线性扫描伏安法等方法研究了热处理和PANI复合比例对复合物的形貌、成键、晶相组成及氧还原性能的影响.结果表明,PANI与Ti O2间存在相互作用,可以抑制Ti O2的团聚和锐钛矿向金红石的转变.热处理制得Ti O2/C的氧还原活性随着PANI载体含量增加先升高后降低,PANI和Ti O2质量比为35/100时,催化剂的氧还原活性最高.同时,循环伏安和时间-电流曲线测试表明,已制备的复合材料在催化氧还原反应进行时具有较好的稳定性.     

TiO_2晶相对MnO_x/TiO_2催化剂催化NO氧化性能的影响（英文）

以浸渍在不同晶相TiO2(金红石型(R)、锐钛矿型(A)和P25型(P))上的锰基催化剂为对象,研究了TiO2晶相对MnOx/TiO2催化剂催化NO氧化活性的影响.结果表明,MnOx/TiO2(P)催化剂活性最高,NO转化率在300°C及GHSV=20000 h–1条件下可达83%.各催化剂活性顺序为MnOx/TiO2(P)MnOx/TiO2(A)MnOx/TiO2(R).采用X射线粉末衍射、场发射扫描电子显微镜、X射线光电子能谱、H2程序升温还原和O2程序升温脱附等手段研究了TiO2晶相影响MnOx/TiO2催化剂催化活性的作用机理.结果表明,相比于A和R型TiO2,P型TiO2能够增加MnOx在其表面的分散度并抑制催化剂颗粒的团聚和粘连,且更有利于Mn2O3的生成,而后者催化NO氧化活性比其它MnOx更高;此外,P型TiO2可以增加MnOx尤其是Mn2O3的还原性,并可促进O2–从M3+–O键的脱附.     

具有低SO_2氧化活性的Pt/Zr_xTi_(1-x)O_2柴油车氧化催化剂的制备及性能

采用共沉淀法制备了一系列ZrxTi1-xO2(x=0.0,0.1,0.5,0.9,1.0)复合氧化物,并以此为载体,用等孔体积浸渍H2PtCl6制得Pt/ZrxTi1-xO2柴油车氧化催化剂.运用N2吸附-脱附,X射线多晶粉末衍射,X射线光电子能谱,H2程序升温还原和NH3程序升温脱附等手段对催化剂进行了表征.结果表明,在系列催化剂样品中,Zr0.1Ti0.9O2复合氧化物主要以锐钛矿形式存在,具有较好的织构性能,样品的比表面积达94m2/g,孔体积为0.33cm3/g.相应地,Pt/Zr0.1Ti0.9O2催化剂表现出优异的催化氧化性能,HC和CO的起燃温度(T50)分别为185和174oC,完全转化温度(T90)分别为197和201oC;且具有较低的SO2氧化活性,350oC时SO2仅转化25.5%.     

不同晶相TiO2负载Cu2O催化甲醛乙炔化反应

分别以金红石相和锐钛矿相TiO₂为载体, 采用液相还原-沉积法制备了Cu₂O/TiO₂催化剂. 采用氮气物理吸附-脱附(N₂-physisorption)实验、 氢气程序升温还原(H₂-TPR)、 X射线衍射(XRD)、 X射线光电子能谱(XPS)、 CO红外光谱(CO-IR)及高分辨透射电子显微镜(HRTEM)等技术, 研究了不同晶相TiO₂载体对Cu₂O/TiO₂结构及其催化甲醛乙炔化反应性能的影响. 结果表明, 以金红石相TiO₂为载体的催化剂炔化活性明显高于以锐钛矿相TiO₂为载体的催化剂, 原因在于金红石相TiO₂主要暴露(110)晶面, 其与铜物种的配位环境及较高的空位密度形成了更多的Cu—O—Ti结构物种, 表现为Cu₂O与TiO₂之间强的相互作用. 这导致Cu₂O高效转变为乙炔亚铜活性物种, 并保持了较高的分散度与稳定性, 抑制了过度还原物种金属Cu的生成, 进而使催化剂表现出较高的催化性能.     

氮气气氛下焙烧的CeO_2载体负载Ni基催化剂的顺酐加氢性能研究

在氮气气氛中合成了具有较高氧缺陷浓度的CeO_2载体,采用浸渍法制备了Ni含量为10%的Ni/CeO_2-N催化剂,考察了其顺酐液相加氢性能,并与氧气气氛中制得的CeO_2载体负载Ni催化剂作了对比.N_2低温物理吸脱附,X-射线衍射,拉曼光谱,H_2程序升温还原等表征手段表明,在氮气气氛中合成的CeO_2具有较高浓度的氧缺陷位,在催化剂还原过程中可促进NiO物种的还原,同时在催化剂表面生成更多的氧缺陷位.该氧缺陷位可与活性金属Ni物种协同作用,显著提高催化剂的C=C及C=O加氢活性.     

载体焙烧温度对稀燃天然气汽车尾气净化Pd/Zr0.5Al0.5O1.75催化剂性能的影响

以不同温度焙烧得到的Zr0.5Al0.5O1.75复合氧化物为载体,制备了系列1.5%Pd/Zr0.5Al0.5O1.75催化剂样品.采用N2吸附-脱附、X射线衍射、H2程序升温还原、O2程序升温脱附及CO化学吸附等手段对催化剂进行了表征,并测试了催化剂在模拟稀燃天然气汽车尾气中的活性和抗H2O中毒性能.结果表明,载体...     

载体焙烧温度对Ru/MgAl2O4催化剂液相苯部分加氢性能的影响

采用水热合成法制备了镁铝尖晶石(MgAl2O4)材料,制备了其负载的Ru催化剂,研究了MgAl2O4焙烧温度对Ru/MgAl2O4催化剂上液相苯部分加氢催化性能的影响.采用X射线粉末衍射、27A1固体核磁共振、傅里叶变换红外光谱、H2-程序升温还原、H2-程序升温脱附、N2物理吸附、透射电子显微镜和X射线光电子能谱等手...     

超亲水TiO2和TiO2-SiO2表面的动态润湿性

1997年, Fujishima研究组[1]发现TiO2表面经UV光照射能产生较强的亲水性, 同时具有较高的亲油性, 即经UV光照射后的TiO2表面具有超双亲的性质. 这种防雾和自清洁性在工业上应用广泛, 已引起了人们的极大兴趣[2～5]. 进一步的研究发现, 超亲水的TiO2表面在暗处放置会变为疏水表面. 对于这个问题, 除了可以通过UV光照[6]、氩离子或电子束溅射[6]和高温热处理[5]等恢复其超亲水性外, 还可以通过添加摩尔分数为10%～30%的SiO2有效地降低TiO2表面的接触角, 提高UV光诱导的超亲水表面在暗处的稳定性能[3]. 另外, 诱导TiO2的亲水性需要较强的UV线强度(如太阳光), 使它在室内应用受到限制. 为了在室内实现TiO2的自清洁功能, Watanabe等[4]发现在TiO2中添加WO3可使TiO2在室内的照明光下也能实现亲水性转变. 以上这些研究成果为TiO2在工业和生活上的实际应用提供了重要的科学依据. 然而, TiO2的防雾和自清洁功能的实现同时也受其动力学性质的制约.     

Preparation and solar-light photocatalytic activity of TiO2 composites: TiO2/kaolin,TiO2/diatomite,and TiO2/zeolite

Three TiO₂ loaded composites, TiO₂/kaolin, TiO₂/diatomite, and TiO₂/zeolite, were prepared in order to improve the solar-light photocatalytic activity of TiO₂. The results showed that the photocatalytic activity could obviously be enhanced by loading appropriate amount of inorganic mineral materials. Meanwhile, TiO₂ content, heat-treatment temperature and heat-treatment time on the photocatalytic activity were reviewed. Otherwise, the effect of solar light irradiation time and dye concentration on the photocatalytic degradation of Acid Red B was investigated. Furthermore, the degradation mechanism and adsorption process were also discussed.     

Yellow pigments based on Fe2TiO5 and TiO2

The aim of our research was to prepare yellow pigments based on structure of pseudobrookite Fe₂TiO₅. Part of Fe was substituted with Li and Ti from Fe₂TiO₅ to Li_0.05Fe_0.07Ti_2.44O₅. Synthesis and pigmentary-application properties in the Li₂O–Fe₂O₃–TiO₂ system were studied for 800 and 900°C using classical ceramic method of preparation. The main attention was aimed to usage of four different sources of titanium compounds as raw materials. We studied the influence of different sources of titanium compounds on the structural and the colour properties of the prepared pigments. The thermal analysis was used for characterization of titanium compounds and determination of their thermal stability.     

Photocatalytic reduction of nitrate over TiO2 and Ag-modified TiO2

This research work presents the efficiency of the TiO₂ and Ag–TiO₂ thin films prepared by the sol–gel method and coated onto the surface of 304 stainless steel sheets used in the photocatalytic nitrate reduction processes. The Ag–TiO₂ thin films had the weight by weight (w/w) ratio of Ag⁺/TiO₂ of 0.1% as Ag atom. The XRD results showed that the crystalline phase structure of TiO₂ on the Ag–TiO₂ thin films was anatase. The optical band gaps of the TiO₂ and 0.1% Ag–TiO₂ thin films were respectively 3.27 and 2.70 eV, while the surface of the prepared catalysts was hydrophobic with the respective average water contact angles of 94.8° and 118.5° for the TiO₂ and 0.1% Ag–TiO₂ thin films. The net efficiencies of photocatalytic nitrate reduction of TiO₂ and 0.1% Ag–TiO₂ were 41.4% and 70.0%, respectively. The loading of Ag only influenced the nitrate removal efficiency without affecting the stoichiometric ratio of formate to nitrate. The net stoichiometric ratio of formate to nitrate of all experiments was 2.8:1.0, which is close to the stoichiometric ratio of 2.5:1.0 of the nitrate reduction to nitrite and then to nitrogen gas.     

STS study of TiO2 film and Pt-deposited TiO2 film in air

Direct investigation of the electronic structure of catalyst surfaces on the near-atomic scale in general has not been impossible in the past. However, with the advent of the scanning tunneling microscope (STM), the opportunity arises for incorporating the scanning tunneling spectroscopy (STS) for correlation in-situ surface electronic structure with topography on a sub-nanometer scale. In this paper, we report the STS results of thin film TiO2 and Pt-deposited TiO2 annealed at 450℃. It was found that the TiO2 semiconductor changes from n-type to p-type after Pt deposition.Fig. 1 shows the surface electronic property (Ⅰ-Ⅴ curve) of thin TiO2 film measured in air by STS. A steep descent of the anodic tunneling current at ca.- 1.0 Ⅴ and a rapid ascent of cathodic tunneling current at ca. +2.0V. The zero bias represents the Fermi level (Ef). Ef is situated at the Ecb side indicating that the thin TiO2 film possesses the same band gap as that of bulk TiO2 phase ( Egs =3.0 to 3.2 eV). For the sample of Pt-deposited TiO2 film, Pt/(Pt+Ti+O) atomic ratio≈0.2, which indicates that the surface of TiO2 film is partly covered by Pt particles, and there are two types of Ⅰ-Ⅴ curves to be detected. One of them (Fig.2a)is attributed to the electronic property of TiO2, which has same Egs as that shown in Fig. 1. However, the Ef is transferred to valence side (△≈1eV). This phenomenon hints that TiO2 is doped by an impurity which can introduce h+ into TiO2 lattice.Such a type of defects may be described by Ti1-xPtxO2(h )2x, here Pt+2 as a substitutional site of Ti+4. Fig.2b is the Ⅰ-Ⅴ curve of a Pt particle situated on a TiO2 particle contained Ti1-xPtxO2(h )2x.     

Structure of TiO2 in TiO2-SiO2 prepared by a complexing agent-assisted sol-gel procedure

Many types of TiO₂-SiO₂ (Ti:Si=50:50 mol%) were prepared by the sol-gel procedure with and without 2-methyl-2, 4-pentanediol (MPD) as an organic ligand. The effect of MPD on the gel structure and the properties of the TiO₂ crystals were studied by XRD and raman spectroscopy, and the effect of the sol standing time on the properties of the TiO₂ crystals were also studied by XRD spectroscopy. In the gels with MPD, anatase of TiO₂ appeared at approximately 580°C, and the crystal structures were similar despite the difference in the gel preparation procedure. The titania gels with MPD were presumed to be dispersed in the silica gel matrix without any Ti-O-Si bond. In the presence of MPD, the formation of titania gels is controlled and the specified TiO₂ crystal is produced.     

Fibrous TiO2-SiO2 nanocomposite photocatalyst

The electrospinning method is employed to prepare a fibrous TiO2-SiO2 (Ti : Si = 1 : 2) nanocomposite photocatalyst, in which Degussa P25 T i O2 nanoparticles are embedded inthe body of SiO2 fibers and which shows good photocatalytic activity due to its 3-D open structure, as evidenced by photocatalytic reduction of silver ions and decomposition of acetaldehyde.