Synthesis and Characterization of Photocatalytic Porous Fe3+/TiO2 Layers on Glass

Wet chemical synthesis and preliminary photocatalytical characteristics of titania and Fe(III)-containing TiO₂ layers are presented. A highly stable coating colloids could be prepared under base- as well as acid-catalyzed condensation conditions. Structural properties of the as-prepared wet gels and sintered films were investigated using SEM, TEM, XRD as well as optical absorption spectroscopy, DTA-TG analysis and photomineralisation studies. X-ray amorphous wet titania gel layers start to crystallize at 500°C forming the characteristic anatase phase. In the presence of iron ions (Fe/Ti = 1), nanocrystalline FeTiO₃ ilmenite phase forms. Both TiO₂ and Fe-containing TiO₂ films demonstrate a photocatalytic activity in the process of the photomineralization of dichloroacetic acid.     

Synthesis of bimodal porous structured TiO2 microsphere with high photocatalytic activity for water treatment

In this work bimodal structured titanium dioxide (TiO₂) microsphere has been prepared from commercial TiO₂ powder and nano-sized titania gel via sol–gel spray-coating technique. Crystallization and transformation behavior of titania gel were investigated. The results revealed that the crystallization and transformation of anatase particles were substantially affected by the concentration of solvent and calcination temperature. Anatase crystallite size of 10 nm was obtained at mole ratio of solvent/precursor 50/1 and calcination temperature of 450 °C. The prepared nano-sized titania gel was embedded within the core (commercial TiO₂, P25) during the spraying process. The prepared TiO₂ microsphere was characterized using X-ray diffractometer (XRD), scanning electron microscope (SEM), field emission electron microscope (FESEM) and micropore analysis. The photocatalytic activity was monitored by following the degradation of phenol with activity benchmarked against commercial P25 (Degussa). The increase of photocatalytic activity of TiO₂ microsphere was attributed to the nano-sized anatase crystallite which has been incorporated into the TiO₂ microsphere.     

Spongelike Macroporous TiO2 Monoliths Prepared from Starch Gel Template

TiO₂ materials with a hierarchical meso/macropore organization were fabricated by using titanium dioxide nanoparticles and starch gel templates. Starch sponges with high internal macroporosities were prepared by freezing and thawing of starch gels and were then infiltrated with colloidal suspensions of titania nanoparticles and air-dried to produce TiO₂-starch foams with pores up to 200 m across depending on the starch concentration and the TiO₂ loading. The TiO₂ nanoparticles were deposited as coherent layers on the thin walls of the starch framework, which was removed by calcination without significant disruption of the TiO₂ framework. The three dimensional macroporous structures of TiO₂-starch sponge composite and TiO₂ sponge induced extremely high photocatalytic activity.     

The Effect of SiO2 Addition on the Grain Size and Photocatalytic Activity of TiO2 Thin Films

The uniform transparent TiO₂/SiO₂ nanometer composite thin films were prepared via sol-gel method on the soda lime glass substrates, and were characterized by X-ray photoelectron spectroscopy (XPS), FTIR spectroscopy, UV-VIS spectroscopy, transmission electron microscopy (TEM), X-ray diffraction (XRD) and BET surface areas. It was found that the addition of SiO₂ to TiO₂ thin films could suppress the grain growth of TiO₂ crystal and increase the hydroxyl content of the surface of TiO₂ films. The photocatalytic activity of the as-prepared TiO₂/SiO₂ composite thin films increases for SiO₂ content of less than 5 mol%.     

Thermal behaviour study of some sol-gel TiO2 based materials

Among the great number of sol-gel materials prepared, TiO₂ holds one of the most important places due to its photocatalytic properties, both in the case of powders and coatings. Impurity doping is one of the typical approaches to extend the spectral response of a wide band gap semiconductor to visible light. This work has studied some un-doped and Pd-doped sol-gel TiO₂ nanopowders, presenting various surface morphologies and structures. The obtained powders have been embedded in vitreous TiO₂ matrices and the corresponding coatings have been prepared by dipping procedure, on glass substrates. The relationship between the synthesis conditions and the properties of titania nanosized materials, such as thermal stability, phase composition, crystallinity, morphology and size of particles, and the influence of dopant was investigated. The influence of Pd on TiO₂ crystallization both for supported and unsupported materials was studied (lattice parameters, crystallite sizes, internal strains). The hydrophilic properties of the films were also connected with their structure, composition and surface morphology. The methods used for the characterization of the materials have been: simultaneous thermogravimetry and differential thermal analysis, powder X-ray diffraction, electron microscopy (TEM, SAED) and AFM.     

Ultradeep Hydrodesulfurization of Dibenzothiophene (DBT) Derivatives over Mo-Sulfide Catalysts Supported on TiO2-Coated Alumina Composite

The present paper reviews in detail the different studies now being conducted by our research team concerning the ultradeep hydrodesulfurization (HDS) of dibenzothiophene (DBT) derivatives over Mo/TiO₂ and Mo/TiO₂–Al₂O₃ catalysts. First, a detailed characterization of Mo/TiO₂ (P-25 Degussa, 50 m²/g) catalysts prepared by equilibrium adsorption technique shows that Mo- species are highly and uniformly dispersed on the surface of titania up to 6.6 wt% MoO₃ loading. Above this value, some aggregation of Mo occurs, leading to the formation of bulk MoO₃. Below 6.6 wt% MoO₃ loading, the Raman spectroscopy data of the calcined samples show that the supported Mo-species possess a highly distorted octahedral MoO₆ structure. TiO₂–Al₂O₃ composites were prepared by chemical vapor deposition (CVD) using TiCl₄ as a precursor. Using several characterization techniques, we demonstrated that the support composite presents a high dispersion of TiO₂ over -Al₂O₃ without forming precipitates up to ca. 11 wt% loading. Moreover, the textural properties of the composite support are comparable to those of alumina. Under the present sulfidation conditions (673 K, 5%H₂S/95%H₂), Mo-species supported on TiO₂ are better sulfided than on alumina, as demonstrated using XPS. This can be attributed to the relatively lower interaction between Mo-species and titania. The state of sulfide species supported on the composite support can be considered as a transition state between TiO₂ and Al₂O₃. However, at relatively higher TiO₂ loadings (ca. 11 wt%), Mo/TiO₂–Al₂O₃ catalysts exhibit sulfidability similar to that of Mo/TiO₂. The HDS tests conducted in both the laboratory and in industry show that sulfide catalysts supported on TiO₂–Al₂O₃ (ca. 11 wt% TiO₂) are more active than those supported on TiO₂ or Al₂O₃.     

Preparation, characterization, and infrared emissivity property of optically active polyurethane/TiO2/SiO2 multilayered microspheres

Optically active polyurethane/titania/silica (LPU/TiO₂/SiO₂) multilayered core–shell composite microspheres were prepared by the combination of titania deposition on the surface of silica spheres and subsequent polymer grafting. LPU/TiO₂/SiO₂ was characterized by FT-IR, UV–vis spectroscopy, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), thermogravimetric analysis (TGA), SEM and TEM, and the infrared emissivity value (8–14 μm) was investigated in addition. The results indicated that titania and polyurethane had been successfully coated onto the surfaces of silica microspheres. LPU/TiO₂/SiO₂ exhibited clearly multilayered core–shell construction. The infrared emissivity values reduced along with the increase of covering layers thus proved that the interfacial interactions had direct influence on the infrared emissivity. Besides, LPU/TiO₂/SiO₂ multilayered microspheres based on the optically active polyurethane took advantages of the orderly secondary structure and strengthened interfacial synergistic actions. Consequently, it possessed the lowest infrared emissivity value.     

Study on mechanism of photocatalytic performance of La-doped TiO2/Ti photoelectrodes by theoretical and experimental methods

TiO₂ photoelectrodes with various nanostructures have been successfully prepared by the anodization method. The morphology, microstructure and optical properties of as-prepared photoelectrodes were studied by scanning electron microscopy (SEM), X-ray diffraction (XRD), ultraviolet/visible light diffuse reflectance spectra (UV/vis/DRS), surface photovoltage spectroscopy (SPS) and photocurrent. The electronic structure and optical properties of La doped/undoped TiO₂ photoelectrodes with different crystal structures were calculated by the density function theory. The photocatalytic and photoelectrocatalytic activities of as-prepared photoelectrodes were evaluated. The results showed that the anodization potentials played a crucial role in the surface morphology and microstructure. Both results of theoretical calculations and experimental tests demonstrated that La-doped photoelectrodes were more sensitive to light than undoped one. The difference of photoelectrodes performance was ascribed to the crystal configuration, impurity energy levels and long-range orientation moving of photogenerated carriers.     

Enhanced ethanol sensing properties of WO3 modified TiO2 nanorods

Pristine and WO₃ decorated TiO₂ nanorods (NRs) were synthesised to investigate n-n-type heterojunction gas sensing properties. TiO₂ NRs were fabricated via hydrothermal method on fluorine-doped tin oxide coated glass (FTO) substrates. Then, tungsten was sputtered on the TiO₂ NRs and thermally oxidised to obtain WO₃ nanoparticles. The heterostructure was characterised by X-ray diffraction (XRD), scanning electron microscopy (SEM), and energy-dispersive X-ray (EDX) spectroscopy. Fabricated sensor devices were exposed to VOCs such as toluene, xylene, acetone and ethanol, and humidity at different operation temperatures. Experimental results demonstrated that the heterostructure has better sensor response toward ethanol at 200 °C. Enhanced sensing properties are attributed to the heterojunction formation by decorating TiO₂ NRs with WO₃.     

Synthesis of nanosized TiO2/SiO2 particles using microwave processes and their photocatalytic activity on the decomposition of orange II

The nanosized titania and TiO₂/SiO₂ particles were prepared by the microwave-hydrothermal method. The effect of physical properties TTIP/TEOS ratio and calcination temperature has been investigated. The major phase of the pure TiO₂ particle is of the anatase structure, and a rutile peak was observed above 800°C. In TiO₂/SiO₂ particles, however, no significant rutile phase was observed, although the calcination temperature was 900°C. No peaks for the silica crystal phase were observed at either silica/titania ratio. The crystallite size of TiO₂/SiO₂ particles decreases as compared to pure TiO₂ at high calcination temperatures. The TiO₂/SiO₂ particles show higher activity on the photocatalytic decomposition of orange II as compared to pure TiO₂ particles.     

V2O5-TiO2复合半导体光催化材料结构及光响应性能研究

采用溶胶凝胶法制备了V₂O₅-TiO₂复合半导体材料，通过Raman、XRD及UV-Vis DRS等实验方法研究了V₂O₅与TiO₂复合对材料表面组成、晶体结构以及光响应性能的影响。结果表明：钒加入后优先与TiO₂作用形成较为稳定的金红石型TiVO₄晶相，其中V⁴⁺是促进TiO₂发生相变的关键；随着钒加入量的增加，V₂O₅由表面高分散状态逐渐聚集形成晶相，并释放部分Ti⁴⁺使之形成锐钛矿型TiO₂晶相，使得体相中金红石型TiO₂的含量有所下降；复合后形成的TiVO₄晶相显著提高了材料对可见光的吸收率，并使其吸光域红移至460 nm左右。     

Photocatalytic Crystalline and Amorphous TiO2 Nanotubes Prepared by Electrospinning and Atomic Layer Deposition

In this work core/shell composite polymer/TiO₂ nanofibers and from those TiO₂ nanotubes were prepared. First, poly(vinyl alcohol) (PVA) and poly(vinylpyrrolidone) (PVP) fibers were synthetized by electrospinning. They were covered with a 100 nm thick amorphous TiO₂ layer by atomic layer deposition at 50 °C. Later the polymer core was removed by two different methods: dissolution and annealing. In the case of dissolution in water, the as-prepared TiO₂ nanotubes remained amorphous, while when annealing was used to remove the polymers, the TiO₂ crystallized in anatase form. Due to this, the properties of amorphous and crystalline TiO₂ nanotubes with exactly the same structure and morphology could be compared. The samples were investigated by SEM-EDX, ATR-IR, UV-Vis, XRD and TG/DTA-MS. Finally, the photocatalytic properties of the TiO₂ nanotubes were studied by decomposing methyl-orange dye under UV light. According to the results, crystalline anatase TiO₂ nanotubes reached the photocatalytic performance of P25, while amorphous TiO₂ nanotubes had observable photocatalytic activity.     

Parameters controlling the photocatalytic performance of ZnO/Hombikat TiO2 composites

Commercial TiO₂ (Hombikat, UV-100) was impregnated with different loadings of zinc nitrate solution and subsequently calcined at different temperatures in order to obtain a stable homogeneous solid composite of ZnO/TiO₂. The prepared samples were characterized by X-ray powder diffraction (XRD), scanning electron microscopy (SEM), high resolution transmission electron microscopy (HR-TEM), UV-vis and Raman spectroscopy, inductively coupled plasma mass spectroscopy (ICP), X-ray photoelectron spectroscopy (XPS) as well as N₂ adsorption and desorption measurements. Results show that ZnO was incorporated within the TiO₂ crystals and did not form a separate bulky phase or metallic zinc. Moreover, the calcination temperature dramatically modifies the texture properties of the prepared samples compared with original Hombikat TiO₂. The photocatalytic performance of the prepared samples was evaluated by monitoring the degradation of methyl orange dye under black light illumination. Three main parameters were studied; ZnO loading, surface area and initial pH of the methyl orange solution. The variation in ZnO loading appears to have less influence on the catalytic activity than either the surface area or the pH.     

Homogeneous liquid crystal orientation on ion beam exposure TiO2 surfaces depending on an anisotropic dipole field

We studied homogeneous liquid crystal (LC) alignment properties on ion-beam (IB) irradiated TiO₂ films deposited by the electron beam evaporation method. Stable homogeneous LC alignment on a TiO₂ surface resulted from IB irradiation energy over 1800 eV. X-ray photoelectron spectroscopy analyses showed that Ti⁴⁺ 2p_3/2 and Ti⁴⁺ 2p_1/2 peaks were increased with increasing IB energy. Assuming that the increased peaks produced anisotropy dipole fields in the direction of the IB exposure process, we confirmed that the increasing IB energy induced strengthened the surface energy for entirely clear and stable LC molecule orientation. The voltage-transmittance characteristics of the twisted-nematic cell on the TiO₂ surface indicate that the TiO₂ film has potential for use as the LC alignment layer.     

Porosity, structural and fractal study of sol-gel TiO2-CeO2 mixed oxides

Sol-gel TiO₂-CeO₂ materials were synthesized at pH=3 employing HNO₃ as hydrolysis agent. Gels were thermally treated at 473, 673, 873, and 1073 K, respectively. Morphologies of the final substrates were studied via N₂ sorption, XRD and TEM. N₂ isotherms indicated a steady porosity in TiO₂-CeO₂ samples treated up to 873 K. Adsorption-desorption isotherms and TEM micrographs were used to perform fractal analyses of annealed samples. A dominant anatase phase was detected by XRD between 473 and 873 K while a rutile phase was evident at 1073 K. The presence of cerium conferred an increased thermal stability to the TiO₂ materials against particle sintering and pore collapse. The structure of cerium-doped anatase lattice was visualized through crystal simulation to investigate the possible substitution of Ti⁴⁺ by Ce⁺⁴ ions. This effect and the progressive segregation of CeO₂ crystals with temperature on the surface of TiO₂ grains lead to substrates of assorted morphologies.     

Sol-Gel Derived TiO2-SiO2 Fibres

TiO₂−SiO₂ fibres with 0, 5, 10 and 20 volume % SiO₂ have been prepared by drawing from a gel followed by sintering at different temperatures. Nearly one meter long fibres can be drawn easily in conditions of about 50% relative humidity. Addition of SiO₂ inhibits the crystallisation of TiO₂ and also the anatase → rutile transformation and improves the strength of the fibres. While the pure TiO₂ fibres are brittle, those with 5, 10 and 20 volume % SiO₂ are flexible and strong. Tensile strength values as high as 3 GPa have been achieved in the 10 volume % SiO₂−TiO₂ fibres. Fibres heated above 900°C are brittle. The shape of the cross section of the fibres is found to depend on their diameters.     

Ultra-low expansion glass from gels

Pyrolysis of mixed titanium and silicon metal halides produces a commercial glass (7.4% TiO₂) with ultra-low thermal expansion that is essentially zero over the temperature range of 0 to 300°C. A colloidal particulate gel process involving potassium silicate, titania sol and formamide gel reagent was found to produce glass compositions with similar low expansion behavior. Due to the strongly basic nature of the precursor solutions, special titania sols had to be prepared that were stable in these alkali silicate solutions. The preferred TiO₂ sols were those containing quaternary ammonium stabilizing counter-ions. These sols served not only as the source of homogeneously distributed titania, but they may also serve as nucleating species that contribute to particle growth and pore size control of the gel network. The large pore (0.3 µm) TiO₂/SiO₂ gel structures were easily dealkalized, dried and sintered to uncracked glass shapes. Plates up to 9.5 cm×6.6 cm× 0.5 cm thick and some intricate cast shapes were produced and their glass properties evaluated.     

CuO Catalysts Supported on Porous TiO2 Microspheres for Low-Temperature CO Oxidation

The porous TiO₂ microspheres were prepared by the reversed-phase suspension polymerization and sol-gel method using reversed-phase suspension droplets as the templates. The CO oxidation catalytic properties of the CuO/TiO₂ catalysts prepared by hydrothermal method and impregnation method were extensively investigated. The structure of CuO/TiO₂ catalysts was determined by TG-DTA, XRD, TEM, and XPS. The results indicated that the redox capacity of CuO/TiO₂ was greatly depended on the aqueous solution concentration of Cu(NO₃)₂ used in the preparation of CuO/TiO₂ and the calcination temperature of the CuO/TiO₂ catalysts.     

Hierarchical chlorine-doped rutile TiO2 spherical clusters of nanorods: Large-scale synthesis and high photocatalytic activity

In this study, we report the synthesis of hierarchical chlorine-doped rutile TiO₂ spherical clusters of nanorods photocatalyst on a large scale via a soft interface approach. This catalyst showed much higher photocatalytic activity than the famous commercial titania (Degussa P25) under visible light (λ>420 nm). The resulting sample was characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), high-resolution TEM (HRTEM), nitrogen adsorption, X-ray photoelectron spectroscopy (XPS), UV-vis diffuse reflectance spectroscopy, ¹H solid magic-angle spinning nuclear magnetic resonance (MAS-NMR) and photoluminescence spectroscopy. On the basis of characterization results, we found that the doping of chlorine resulted in red shift of absorption and higher surface acidity as well as crystal defects in the photocatalyst, which were the reasons for high photocatalytic activity of chlorine-doped TiO₂ under visible light (λ>420 nm). These hierarchical chlorine-doped rutile TiO₂ spherical clusters of nanorods are very attractive in the fields of environmental pollutants removal and solar cell because of their easy separation and high activity.     

Pyrolysis study of sol-gel derived TiO2 powders: Part IV. TiO2-anatase prepared by hydrolysing titanium(IV) isopropoxide without chelating agents

An amorphous TiO₂ gel was obtained by hydrolysing titanium(IV) isopropoxide with a stoichiometric amount of water using SnCl₂ as catalyst. In these operative conditions, a TiO₂ gel matrix containing a lower fraction of organic residual was obtained with respect to samples prepared by previously modifying the titanium alkoxide precursor with chelating ligands. Dried gel powders were characterized by N₂ adsorption analyses, FT-IR and XRD measurements. Thermogravimetric (TG) and differential thermal analysis (DTA) coupled with mass spectrometric (MS) and gas chromatographic (GC) measurements were performed in order to identify the organic products released from TiO₂ gel pyrolysis. The Tg-MS semiquantitative analysis of the main evolved species allowed to describe both the chemical composition of the initial TiO₂ gel and the chemical rearrangements occurring in the matrix during heating up to its crystallisation to anatase form at 420°C.This revised version was published online in November 2005 with corrections to the Cover Date.