以硼化物为活化剂制备负载茂金属催化剂催化乙烯/α-烯烃共聚合

本研究以硅胶为载体,以Cp2ZrCl2为主催化剂,分别以甲基铝氧烷（MAO）、三五氟苯基硼（B(C6F5)3）、N,N-二甲基苯铵四(五氟苯基)硼酸盐（[HNMe2Ph][B(C6F5)4]）、三苯碳鎓四(五氟苯基)硼酸盐（[Ph3C][B(C6F5)4]）、三五氟苯基硼/三甲基铝（B(C6F5)3/TMA）为活化剂制备了负载茂金属催化剂,考察了它们对乙烯均聚、乙烯/α-烯烃共聚合的影响。实验结果表明,当硼化物用量为5.1?0-4mol/g SiO2,B/Zr在14.10~19.04之间时,负载茂金属催化剂催化烯烃聚合活性达107g/(molZr?h),是相同条件下以MAO为活化剂时活性的511~1090倍,同样达到107g/(molZr?h)的催化活性,硼化物用量仅仅为MAO用量1/16;和B(C6F5)3相比,以[HNMe2Ph][B(C6F5)4]和[Ph3C][B(C6F5)4]为活化剂制备的负载茂金属催化剂活性较高,并且以[Ph3C][B(C6F5)4]为活化剂制备的负载茂金属催化剂所得共聚物分子量分布最窄,乙烯/1-己烯共聚物中共单体含量最高,为2.97mol%;采用硼化物为活化剂制备的负载茂金属催化剂催化乙烯/1-己烯、乙烯/1-辛烯共聚合所得共聚产物分子量分布较窄,密度在0.91~0.92g/cm3之间,属于mLLDPE范畴。     

以硼化物为活化剂制备负载茂金属催化剂催化乙烯均聚和乙烯/α-烯烃共聚合（英文）

以硅胶为载体,以Cp2ZrC l2为主催化剂,分别以甲基铝氧烷(MAO)、三五氟苯基硼(B(C6F5)3)、N,N-二甲基苯铵四(五氟苯基)硼酸盐([HNMe2Ph][B(C6F5)4])、三苯碳鎓四(五氟苯基)硼酸盐([Ph3C][B(C6F5)4])、三五氟苯基硼/三甲基铝(B(C6F5)3/TMA)为活化剂制备了负载茂金属催化剂,考察了它们对乙烯均聚、乙烯/α-烯烃共聚合的影响.实验结果表明,当硼化物用量为5.1×10-4mol/g SiO 2,B/Zr在14.10~19.04之间时,负载茂金属催化剂催化烯烃聚合活性达107g/(molZ r·h),是相同条件下以MAO为活化剂时活性的511~1 090倍,同样达到107g/(molZ r·h)的催化活性,硼化物用量仅仅为MAO用量1/16;和B(C6F5)3相比,以[HNMe2Ph][B(C6F5)4]和[Ph3C][B(C6F5)4]为活化剂制备的负载茂金属催化剂活性较高,并且以[Ph3C][B(C6F5)4]为活化剂制备的负载茂金属催化剂所得共聚物分子量分布最窄,乙烯/1-己烯共聚物中共单体含量最高,为2.97%;采用硼化物为活化剂制备的负载茂金属催化剂催化乙烯/1-己烯、乙烯/1-辛烯共聚合所得共聚产物分子量分布较窄,密度在0.91~0.92 g/cm3之间,属于mL LDPE范畴.     

负载双核茂金属催化剂催化乙烯聚合反应动力学研究

以SiO2为载体,制备了负载的双核茂金属[（η5-C5H5）Zr Cl2]2[μ,μ-（SiMe2）2（η5-allyl C5H2）2]/MAO/SiO2催化剂,以己烷为溶剂进行了淤浆条件下乙烯聚合反应,研究了扩散因素、乙烯聚合压力和聚合温度对乙烯淤浆聚合动力学参数的影响,测定了聚合反应级数和表观活化能,采用动力学和相对分子质量法计算了负载催化剂的活性中心浓度,并对链增长速率常数等动力学参数进行了计算.结果表明,以负载双核茂金属催化剂催化乙烯淤浆聚合反应速率对单体浓度呈1.11级依赖,反应活化能Ea为72.47 kJ/mol,活性中心浓度C＊为0.33 mol/mol,链增长速率常数Kp为1.06×106L.（mol.h）-1.     

四甲基环戊二烯基苯氧基二氯化钛衍生物的合成及催化烯烃聚合研究

4-R1-6-R-2-Me4CpH—PhOH[R1=^tBu,R=^tBu(1);R1=H,R=^tBu(2),Ph(3),Me(4)]经双三甲基硅基化后与TiCl4反应,合成了4种限制几何构型茂金属催化剂4-R1-6-R-2-Me4CpH-PhOTiCl2[R1=^tBu,R=^tBu(5);R1=H,R=^tBu(6),Ph(7),Me(8)]。合成产率有较大提高．这些茂金属化合物经过^tBu3Al和Ph3C^ B(C6F5)4^-活化后对乙烯聚合有很好的催化活性,并生成乙基支化聚乙烯．考察了催化剂结构与活性的关系以及聚合反应条件对催化剂性能的影响。并对聚乙烯样品进行了表征．     

烷基铝对球形MgCl_2负载的茂金属催化剂催化乙烯聚合的影响

以甲基铝氧烷(MAO)为助催化剂的茂金属催化剂虽然具有催化活性高、分子量分布窄、聚合物化学组成均匀等优点,但其极高的Al/Zr比和聚合物颗粒形态差等缺点限制了其工业化应用,因此对茂金属催化剂的负载化成为近年来的研究热点.在众多的载体中,球形MgCl2是研究得很少的一类载体,文献中曾采用先负载主催化剂茂金属配合物,聚合时再加入助催化剂MAO的方法[1],由于加入的MAO与主催化剂的络合能力很强,会使部分载上的主催化剂溶解下来,成为均相聚合[2,3],导致聚合物颗粒形态差,且粘釜现象严重.我们则采用相反的思路,即先将助催化剂MAO负载在球形MgCl2上,制得MgCl2/MAO,在聚合前再将MgCl2/MAO与Et[Ind]2ZrCl2混合陈化,并立即在少量烷基铝活化下引发乙烯聚合[4],实验结果表明,该催化剂聚合活性高、聚合物的颗粒形态好、且不粘釜,是一种新型的载体催化剂.由于烷基铝的加入可使催化剂的活性大幅度提高,所以本文将烷基铝也称作助催化剂,来研究其对该载体催化剂催化乙烯聚合的影响.     

单茂钪催化乙烯与苯乙烯衍生物共聚合的研究

以(C5Me4Si Me3)Sc(CH2C6H4NMe2-o)2和[Ph3C][B(C6F5)4]组成的单茂钪催化体系,考察了其催化不同取代基团苯乙烯衍生物均聚合以及与乙烯共聚合的性能.结果表明单茂钪催化体系可以催化对甲基苯乙烯和对乙烯苯基二甲基硅烷均聚合,高活性(106g聚合物(mol Sc)-1h-1)地获得高间规聚合物;催化二乙烯基苯和乙烯苯基-1-丁烯聚合会发生不同程度的交联反应.在1.01×105Pa乙烯压力下,单茂钪催化体系分别催化对甲基苯乙烯、对乙烯苯基二甲基硅烷与乙烯与共聚合,获得了组成和分子量可控的乙烯/对甲基苯乙烯、乙烯/对乙烯苯基二甲基硅烷共聚物,共聚合活性高达106g聚合物(mol Sc)-1h-1.通过1H-NMR、13CNMR、GPC和DSC对共聚物组成、结构和热性能进行了分析表征.结果表明,在1.01×105Pa乙烯压力下改变苯乙烯衍生物的用量,共聚物中对甲基苯乙烯或对乙烯苯基二甲基硅烷的摩尔含量可以在8 mol%~55 mol%间调控,共聚物含有间规聚对甲基苯乙烯嵌段或间规聚对乙烯苯基二甲基硅烷嵌段、聚乙烯嵌段和乙烯-苯乙烯衍生物的链接序列,共聚物分子量(Mn)可以在3×104~16×104间调控,共聚物具有约127℃的熔点.     

茂金属催化乙烯聚合反应动力学

以茂金属化合物[(CH3)2C(η－C5H3）（η－C9H6）]ZrCl2为主催化剂，甲基铝氧烷MAO为助催化剂催化乙烯聚合，对不同的反应条件下（如温度，铝锆摩尔比）聚合反应的动力学进行了研究，并根据此聚合反应体系的动力学特点及考虑到活性中心的再活化，在分析和研究以往的动力学模型的基础上，对烯烃均相聚合动力学反应作了一些假定，建立了动力学模型，用模型对实验数据进行了拟合，结果表明与实验数据相吻合，可以认为，在该聚合反应体系中，确实存在铝氧烷的再活化作用，根据模拟拟合得到了聚合反应的动力学参数。     

α-Ti(HPO_4)_2微球负载型催化剂的合成及其烯烃聚合催化性能（英文）

2种茂金属催化剂及1种后过渡金属催化剂分别被固载于经过甲基铝氧烷处理后的α-Ti(HPO_4)_2微球表面,制备得到3种微球负载型催化剂。在烯烃聚合反应过程中,3种负载型催化剂均表现出比硅胶负载型催化剂更高的催化活性。2种茂金属负载型催化剂在乙烯、丙烯聚合反应中的活性分别高达6.8×10~7 gPE·(molZr·h)~(-1)和5.0×10~7 gPP·(molZr·h)~(-1),所产生的烯烃聚合产物分子量分布较窄(Mw/Mn2.3),表现出良好的单中心催化特性,而且丙烯聚合产物的等规度高达96.5%。负载型后过渡金属催化剂在乙烯聚合反应中的活性稍低,但也能够达到8.3×10~6 gPE·(molFe·h)~(-1)。3种负载型催化剂催化烯烃聚合产物均成微球型,能够很好地复制载体的形貌。     

α-Ti(HPO_4)_2负载型茂金属催化剂的合成及其催化乙烯聚合性能

将茂金属催化剂Cp_2ZrCl_2负载在层状材料α-Ti(HPO_4)_2上,研究了负载型茂金属催化剂α-Ti(HPO_4)_2/MAO/Cp_2ZrCl_2对乙烯的聚合行为,并将其与以硅胶为载体的负载型茂金属催化剂SiO_2/MAO/Cp_2ZrCl_2的催化性能及MAO/Cp_2ZrCl_2的均相催化性能相比较.结果发现,在相同聚合条件下,α-Ti(HPO_4)_2/MAO/Cp_2ZrCl_2对乙烯的聚合催化活性更高,且聚合产物的相对分子质量更高.α-Ti(HPO_4)_2具有作为茂金属催化剂载体的潜在应用价值.     

双组分茂金属催化剂催化乙烯聚合的研究

选择能形成支链的不对称桥联茂金属化合物Me2 C[(Cp) (Ind) ]ZrCl2 和非桥联的不同结构的茂金属化合物二氯二 (烯基取代环戊二烯 )锆如 ( Cp) 2 ZrCl2 ,(Cp) 2 ZrCl2 和 (Cp) 2 ZrCl2 ,以MAO为助催化剂 ,分别组成三组双组分茂金属催化剂的催化体系 ,催化乙烯聚合 .结果表明 ,两类催化剂组成的双组分茂金属催化体系催化乙烯聚合能得到支化的宽分子量分布的聚乙烯 ;聚合温度和改变两种茂金属催化剂的摩尔比对催化活性和分子量有很大影响 .因此可以利用改变双组分茂金属催化剂的摩尔比例和聚合温度来调控聚合物的分子量和分子量分布 .改变两种茂金属催化剂的摩尔比和聚合温度也能使聚合物的结晶度发生改变     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

正丁胺对激光染料荧光谱影响的研究

用正丁胺作为碳源,采用射频辉光放电制备碳膜,选用激光染料R6G和聚乙二醇混合液作为蒸气源,采用单源热蒸发,在蒸发室与染料同时沉积得到混合膜,用拉曼光谱和红外光谱分析了碳膜的结构和键合方式,分析表明:碳膜中存在胺基团和氢原子.混合膜的荧光谱测量结果表明,认为正丁胺对染料荧光谱的影响是因为胺基和氢原子的存在.     

Cu0-catalysed 1,3-dipolar cycloadditions of α-amino acid derived N,N-cyclic azomethine imines to ynones

A series of 20 CuAIAC reactions between eight 4-acylamino substituted pyrazolidine-3-one-1-azomethine imines and four terminal ynones were performed using Cu⁰ as catalyst. The corresponding fluorescent cycloadducts were obtained in very high yields upon simple workup. Thus, Cu-metal turned out to be a better catalyst than Cu^I in terms of yield and ease of isolation. Availability of azomethine imines, mild reaction conditions, and simple workup enable a “click” access to libraries of densely substituted 2,3-dihydro-1H,5H-pyrazolo[1,2-a]pyrazol-1-ones. Reactivity of differently substituted dipoles was evaluated experimentally and by quantum chemical methods (DFT).     

Synthesis and antioxidative/anti-inflammatory activity of novel fullerene–polyamine conjugates

(E)-4-(Fullerenopyrrolidin-1-yl)-3-methylbut-2-enoic acid and its corresponding succinimidyl ester, readily obtained through Prato-type modification of C₆₀, were used for the selective N-acylation of polyamines. The thus obtained conjugates were evaluated for their antioxidative and anti-inflammatory activity and their cytotoxicity was determined. Members of this family of compounds showed interesting anti-lipid peroxidation, anti-lipoxygenase and anti-inflammatory activity and comparable cytocompatibility to spermidine.