工业Fe-Mn催化剂上基于详细反应机理的F-T合成动力学模型Ⅱ.不同校正方法的动力学模型分析

 通过平衡闪蒸模拟催化剂孔道液体组成、烯烃物理吸附和虚拟烯烃分压等方法,考察了化学反应以外的非本征因素对F-T合成动力学模型的校正. 平衡闪蒸模拟催化剂孔道中烯烃组成的校正计算结果表明,在烯烃浓度出现峰值前,溶解度效应对烯烃再吸附及参与二次反应起主导作用,而在烯烃浓度出现峰值后,烯烃的扩散和物理吸附等效应可能起主导作用. 分析烯烃添加的反应器模拟结果发现,考虑烯烃物理吸附作用的动力学模型校正方法不能够正确反映烯烃添加实验的定性规律,而虚拟烯烃分压校正方法能够正确反映烃分布规律并可定量预测烯烃添加对产物分布规律的影响,这对需要尾气循环的F-T合成工业操作具有重要意义.     

工业Fe-Mn催化剂上基于详细反应机理的F-T合成动力学模型Ⅰ.烯烃再吸附动力学研究

 利用转篮式无梯度反应器,在工业Fe-Mn催化剂上,在较宽的工业操作相关的反应条件下进行了F-T合成反应动力学研究. 首次提出了利用转篮式无梯度反应器反应气氛和反应温度均一的优势,将烃生成反应动力学的估算从传统的对烃生成和水煤气变换这两类发生在不同活性中心的反应同时进行估算的方法中分离出来,简化了烃生成动力学模型的计算. 在基于亚甲基插入的亚烷基机理动力学模型基础上,考虑到乙烯与催化剂表面强的相互作用,将乙烯和乙烷的生成动力学参数单独计算. 动力学模型计算的链增长、烷烃和烯烃生成的活化能均与文献报道值具有较好的一致性. 由F-T合成动力学模型计算的合成气消耗速率、甲烷生成速率和C5+的生成速率较好地与实验值吻合. 通过动力学模型并结合实验结果分析发现,未考虑除化学反应之外的非本征因素的烯烃再吸附动力学模型不能够正确预测烃产物分布偏离ASF规律及烯烷比随碳数增加而下降的现象.     

不同链长正构烷烃在Pt/SAPO-11催化剂上的临氢转化规律研究

采用SAPO-11分子筛制备的双功能催化剂,以碳链长度为10-14的正构烷烃为模型化合物,探索了不同碳数的长链正构烷烃临氢转化反应规律。结果表明,低温下不同碳数的正构烃都表现出较高的异构化选择性,改变反应温度使反应转化率控制在85%以下时,正构烷烃的异构化选择性可以达到90%左右;随着碳数和温度升高,正构烷烃由于发生明显的裂化反应导致转化率提高和异构化选择性降低。采用SAPO-11分子筛催化材料的双功能催化剂具有明显的产物择形异构效应,异构化产物以甲基位于端位和碳链中心的单侧链异构体为主,双(多)支链产物较少。长链正构烷烃在Pt/SAPO-11催化剂上的裂化反应在低转化率以加氢裂化为主,裂化产物的碳数呈均匀分布;在高转化率下以酸催化裂化为主,裂化产物的碳数分布呈现明显的不对称分布特征。     

低碳烷烃氧化脱氢制烯烃非金属催化体系研究进展

低碳烯烃是化学工业的重要原料,通过脱氢反应将低碳烷烃转化为同碳数的烯烃是烷烃高值化利用和烯烃原料多元化的重要途径.烷烃氧化脱氢制烯烃的反应具有不受反应平衡限制、无积炭、反应温度低等优点,一直是研究的热点.传统的金属氧化物具有较好的催化剂活性,但容易造成烯烃的过度氧化而导致烯烃选择性低.硼基催化剂作为一种新型非金属催化剂,表现出显著不同于金属氧化物催化剂的反应特性.六方氮化硼(hBN)被首次报道在丙烷氧化脱氢反应展现高活性,随后系列硼化物(SiB_6、CB_4等)以及负载型硼基催化剂相续被报道.硼催化剂显现出高的催化活性和优异的烯烃选择性,产物中几乎没有完全氧化产物CO2生成,这为选择性断裂C-H键开辟了新路径.大量的谱学以及动力学研究表明催化剂表面BOx物种为催化剂的活性位点.这种打破传统认知的非金属催化剂的催化作用在国际上已经形成一个新的研究热点.此外,非金属炭基催化剂在烷烃氧化脱氢反应中也表现出一定的活性,碳纳米管、碳纳米纤维以及纳米金刚石等炭基催化剂均被用于氧化脱氢反应.炭基催化剂中的羰/醌基被认为是催化活性位;催化剂表面的羧酸、酸酐、内酯等官能团易引起选择性的下降,通过杂原子(B、P、N)掺杂可调变催化剂表面的亲电氧物种,改善烯烃的选择性.本文主要综述了近年来非金属催化低碳烷烃氧化脱氢所涉及的催化剂体系、反应机理等研究进展,最后展望了不同催化剂体系应用于烷烃氧化脱氢反应的未来发展.     

加氢裂化催化剂积炭行为的研究

 用热分析技术和反应色谱等手段及催速老化法对加氢裂化催化剂的积炭行为进行了研究．结果发现：对所涉及的几种不饱和烯烃反应物而言,随着碳链长度的增长,催化剂积炭量略有降低;对直链烷烃反应物,碳链越长则催化剂积炭量越多,且分布于催化剂所有的孔内;在碳数相同的情况下,烯烃的不饱和度越大越容易积炭．     

利用高通量技术研究钴基费托催化剂的宏观动力学

利用高通量技术设计并运行了16路平行动力学固定床反应器,用于测量不同接触时间下的稳态反应物消耗速率和产物生成速率,研究了钴基费托催化剂的宏观动力学,包括C1～C4烷烃与烯烃的稳态反应速率及其随床层的分布,以及它们与反应器温度的关系.在等温固定床非扩散限制的反应条件下,除C1和C2烃类外,Cn的生成速率及CO/H2的消耗速率均随接触时间的增加先上升后下降,且烯烃生成速率的最高点较烷烃更靠近反应器入口;反应温度对速率的影响与转化率有关:生成烷烃的表观活化能大于烯烃.高通量动力学反应器可用于生成宏观动力学数据库,以预测催化剂在工业固定床反应器中的行为.     

纳米HZSM-5催化剂催化烃类转化反应

制备了纳米(20~50 nm)HZSM-5催化剂, 用XRF, TEM和NH3-TPD等手段对催化剂进行了表征. 以正辛烷及苯和正辛烷混合物的转化为模型反应, 研究了单烃和混合烃在纳米HZSM-5催化剂上的转化行为, 考察了反应条件对产物分布的影响. 结果表明, 纳米HZSM-5沸石催化剂具有很强的烃类转化能力, 烃类通过芳构化、 异构化和烷基化等反应转化为高辛烷值的异构烷烃和芳烃, 产物中异构烷烃(C4~C6)和芳烃的质量分数超过90%. 直链烷烃转化为芳烃以生成苯环为主, 混合烃转化为芳烃以苯和小分子烃的烷基化为主. 控制反应条件可抑制苯和C+9芳烃的生成. 产物分析结果表明, 烃类在纳米HZSM-5催化剂上的裂解、芳构化和异构化等遵循正碳离子机理.     

甲烷二氧化碳介质阻挡放电转化产物分布研究

针对介质阻挡放电甲烷二氧化碳转化实验,分析了反应的产物分布,探讨了进料组成和反应器结构对反应的影响.反应产物包括:高H2/CO摩尔比的合成气、气态烃、高辛烷值的汽油组分、醇和酸等含氧有机物.对所述电极结构,产物的选择性随碳数增加而降低;高的甲烷进料浓度有利于烃的生成,对醇和酸的最佳甲烷进料体积分数范围在67.4％～75.1％;放电间隙越小,原料转化率和烃、酸的选择性越大,大的放电间隙对醇的生成有利.     

Co/SiO2催化剂合成重质烃的反应性能

 对近期筛选出的一种重质烃合成反应性能良好的Co／SiO2催化剂进行了500h的寿命试验,考察了在不同反应温度、压力和空速条件下催化剂的反应性能．结果表明,随着反应的进行,催化剂合成重质烃的选择性基本保持不变,但催化剂的活性缓慢下降;经原位再生后,催化剂活性可基本恢复到原来的水平．烃产物主要由烷烃组成,C5＋中烯烃仅占2．25％,产物主要集中在C12～C20馏分段,水相产物中含3．56％～6．56％的有机含氧化合物,其中主要是低碳醇．     

直链烷烃的超临界热稳定性研究

本文考察了正辛烷、正壬烷、正癸烷、正十一烷和正十二烷等5种直链烷烃在超临界条件下的恒容热裂解,采用一级反应动力学简化描述其热裂解过程。跟踪裂解气液产物分布,探讨了液体产物中芳烃含量与热稳定性的关系。在相同反应条件下,奇数碳和偶数碳烷烃热裂解速率、转化率和液体组分中芳烃含量分别随碳数的增加而增加。芳烃产物含量随裂解转化率增加呈指数形式增加,表达了烷烃类化合物热稳定性和裂解变化的规律。     

Alumina-supported iron catalyst - long-term study of the light product distribution in Fischer-Tropsch synthesis

Several models have been proposed to describe the carbon number product distribution and mechanism in Fischer-Tropsch synthesis (FTS). However, these models have not fully explained the product distribution and mechanism owing to the wide range and complexity of hydrocarbons in FTS. This study was conducted based on the Yao and Anderson-Schulz-Flory (ASF) carbon number product distribution models for light (C₁–C₆) hydrocarbon products of a Fe/Al₂O₃ catalyst. The product distribution based on the molar ratio of olefin to paraffin (O/P) and the neighboring olefins was also studied in order to better understand the mechanism in FTS and C₂ olefin deviation during FTS.Two sets of experiments (A and B) with different reaction conditions were conducted in microtubular fixed-bed reactors on the Fe/Al₂O₃ catalyst for 2249 h and 360 h, respectively. We found that the α values from the Yao and ASF carbon number product distribution models are relatively similar. The α values from the Yao carbon number product distribution plots are relatively constant, irrespective of the reaction conditions.Interestingly, it was also found that the secondary reactions of the C₂ olefin by re-adsorption to produce paraffins and long-chain olefins are dependent on the CO conversion and the reaction temperature during the FTS. Also, the product distribution of the neighboring olefins during the reduction condition gave a similar trend to what was observed for other reaction conditions. This result confirmed what was observed in the Yao and ASF carbon number product distribution of the olefins.     

A general model for selectivity in olefin cross metathesis

In recent years, olefin cross metathesis (CM) has emerged as a powerful and convenient synthetic technique in organic chemistry; however, as a general synthetic method, CM has been limited by the lack of predictability in product selectivity and stereoselectivity. Investigations into olefin cross metathesis with several classes of olefins, including substituted and functionalized styrenes, secondary allylic alcohols, tertiary allylic alcohols, and olefins with alpha-quaternary centers, have led to a general model useful for the prediction of product selectivity and stereoselectivity in cross metathesis. As a general ranking of olefin reactivity in CM, olefins can be categorized by their relative abilities to undergo homodimerization via cross metathesis and the susceptibility of their homodimers toward secondary metathesis reactions. When an olefin of high reactivity is reacted with an olefin of lower reactivity (sterically bulky, electron-deficient, etc.), selective cross metathesis can be achieved using feedstock stoichiometries as low as 1:1. By employing a metathesis catalyst with the appropriate activity, selective cross metathesis reactions can be achieved with a wide variety of electron-rich, electron-deficient, and sterically bulky olefins. Application of this model has allowed for the prediction and development of selective cross metathesis reactions, culminating in unprecedented three-component intermolecular cross metathesis reactions.     

Catalyst activity comparison of alcohols over zeolites

Alcohol transformation to transportation fuel-range hydrocarbon over HZSM-5 (SiO₂/Al₂O₃ = 30) catalyst was studied at 360 °C and 300 psig. Product distributions and catalyst life were compared between methanol, ethanol, 1-propanol and 1-butanol as a feed. The catalyst life for 1-propanol and 1-butanol was more than double compared with that for methanol and ethanol. For all the alcohols studied, the product distributions (classified to paraffin, olefin, naphthene, aromatic and naphthalene compounds) varied with time on stream (TOS). At 24 h TOS, liquid product from 1-propanol and 1-butanol transformation primarily contains higher olefin compounds. The alcohol transformation process to higher hydrocarbon involves a complex set of reaction pathways such as dehydration, oligomerization, dehydrocyclization and hydrogenation. Compared with ethylene generated from methanol and ethanol, oligomerization of propylene and butylene has a lower activation energy and can readily take place on weaker acidic sites. On the other hand, dehydrocyclization of the oligomerized products of propylene and butylene to form the cyclic compounds requires the sites with stronger acid strength. Combination of the above mentioned reasons are the primary reasons for olefin rich product generated in the later stage of the time on stream and for the extended catalyst life time for 1-propanol and 1-butanol compared with methanol and ethanol conversion over HZSM-5.     

Isomerizing olefin metathesis as a strategy to access defined distributions of unsaturated compounds from Fatty acids

The dimeric palladium(I) complex [Pd(μ-Br)(t)Bu(3)P](2) was found to possess unique activity for the catalytic double-bond migration within unsaturated compounds. This isomerization catalyst is fully compatible with state-of-the-art olefin metathesis catalysts. In the presence of bifunctional catalyst systems consisting of [Pd(μ-Br)(t)Bu(3)P](2) and NHC-indylidene ruthenium complexes, unsaturated compounds are continuously converted into equilibrium mixtures of double-bond isomers, which concurrently undergo catalytic olefin metathesis. Using such highly active catalyst systems, the isomerizing olefin metathesis becomes an efficient way to access defined distributions of unsaturated compounds from olefinic substrates. Computational models were designed to predict the outcome of such reactions. The synthetic utility of isomerizing metatheses is demonstrated by various new applications. Thus, the isomerizing self-metathesis of oleic and other fatty acids and esters provides olefins along with unsaturated mono- and dicarboxylates in distributions with adjustable widths. The cross-metathesis of two olefins with different chain lengths leads to regular distributions with a mean chain length that depends on the chain length of both starting materials and their ratio. The cross-metathesis of oleic acid with ethylene serves to access olefin blends with mean chain lengths below 18 carbons, while its analogous reaction with hex-3-enedioic acid gives unsaturated dicarboxylic acids with adjustable mean chain lengths as major products. Overall, the concept of isomerizing metatheses promises to open up new synthetic opportunities for the incorporation of oleochemicals as renewable feedstocks into the chemical value chain.     

Product distributions of Fischer-Tropsch synthesis over Co/AC catalyst

The product distributions of Fischer-Tropsch synthesis over Co/AC catalyst are investigated under different reaction conditions in an integral fixed bed reactor.It is found that the product distributions deviate from the ASF distribution.The deviation from ASF distribution is analyzed by taking the readsorption of alkenes and the following secondary reaction into consideration.It is noted that the contents of alcohol,alkene and alkane decline with the increasing carbon number,showing a slighter declining tendency of alkanes than those of alkenes and alcohols.It is also found that high temperature,space velocity,H2/CO in feed gas and low pressure are preferential for light hydrocarbons and alcohols while against the chain propagation.The effect of space velocity on the product distributions especially on the light products is not obvious.It is noticed that low temperature,space velocity,H2/CO and high pressure lead to high contents of alcohols;high temperature,H2/CO and low space velocity lead to high contents of alkanes.The effect of pressure on the amounts of alkanes is not significant;high space velocity and low temperature,pressure,H2/CO are preferential for alkenes.     

Hydroamination and hydroalkoxylation catalyzed by triflic acid. Parallels to reactions initiated with metal triflates

Intermolecular additions of the O-H bonds of phenols and alcohols and the N-H bonds of sulfonamides and benzamide to olefins catalyzed by 1 mol % of triflic acid and studies to define the relationship between these reactions and those catalyzed by metal triflates are reported. Cyclization of an alcohol containing pendant monosubstituted and trisubstituted olefins catalyzed by either triflic acid or metal triflates form products from addition to the more substituted olefin, and additions of tosylamide catalyzed by triflic acid or metal triflates form indistinguishable ratios of the two N-alkyl sulfonamides.     

烯烃在催化裂化催化剂上反应机理的初步研究

在自制的微反-色谱装置上，进行了单体烯烃和催化裂化汽油在不同条件下的催化裂化反应实验。对单体烯烃的裂化反应规律和汽油中的烯烃在半再生催化剂和待生催化剂上的催化裂化反应规律进行对比分析。结果表明，单体烯烃反应中，C6及C6以下的烯烃主要发生骨架异构和双键异构反应，氢转移和直接裂化反应发生的较少。C7以上的烯烃95%以上发生转化，高温下直接裂化生成C3、C4，氢转移和异构化比率较大。汽油中的烯烃转化主要集中在C7以上，烯烃之间存在一定的交互作用，单体烯烃的催化裂化反应规律可以初步预测汽油中烯烃的转化。催化剂上的结焦类型对汽油中的烯烃的转化方式没有影响。     

Esterification and Selective Esterification in the Presence of TiCl4

A series of carboxylic acids was esterified to the corresponding esters with TiCl_4 as catalyst at room temperature,in high yields.This catalyst was highly effective for the selective esterification of primary alcohols with carboxylic acids,in the presence of secondary alcohols,and for the selective esterification of saturated acid with alcohol in the presence of conjugated acid or aromatic acid.On account of the high yield,high chemoselectivity,mild condition,and being free of other dehydrants,this is an efficient method.     

K、Mn助剂协同效应对Fe基催化剂上CO加氢制低碳烯烃反应性能的影响

采用典型方法制备了不同Fe、Mn、K比例的铁基催化剂,利用X射线粉末衍射、N₂吸附/脱附、扫描电镜、拉曼光谱、H₂-TPR等手段对催化剂进行了表征,并考察了催化剂对CO加氢制低碳烯烃反应的催化性能。结果表明,Mn能有效促进活性相分散,抑制碳链增长,但Fe-Mn强相互作用不能有效增加低碳烃烯/烷比,α-Fe₂O₃作为活性铁物种前驱体对烯烃生成反应更加有利。K通过减少Mn以氧化物形式出现,增加FeMn化合物晶格缺陷,从而最终使Fe-Mn-K催化剂低碳烯烃收率显著高于Fe-Mn和Fe-K体系。