气相色谱法测定化妆品中的 VE 含量

介绍了一种用气相色谱法准确快速测定品中ＶＥ２含量的新方法。该法以ＶＣ作保护剂,用环已烷提取样品,ＳＥＰ－ＰＡＫ ＡＬＵＭ－Ａ小柱净化。以氯氰菊酯内标物,在１？５％ＯＶ＝－１７色谱柱上进行分离,测定化妆口中ＶＥ含量。内标物与样品的分离度为１．５５。平均回收纺为９４．３％～９８．８％,相对标准偏差为１．７％～３．５％（ｎ＝５）。     

丙烯腈中微量杂质的毛细管色谱法分析

提出了一种分析丙烯腈中微量杂质的大孔径ＯＶ－１０１和ＯＶ－１７ＳＣＯＴ串联柱及毛细管进样系统。结果表明串联柱具有寿命长和分离效率高的特点,定量分析误差小于４％。     

单萜/马来酸酐加成物在OV-101柱上的气相色谱性能与应用

研究了单萜／马来酸酐加成物及其二溴代物在ＯＶ－１０１柱上的某些色谱性能和定量分析的线性相应关系。结果表明这两种化合物在涂渍量为５％～１０％时均能正常出峰;它们在汽化温度高于２００℃时才能够出峰,２８０℃以后,色谱峰面积与汽化温度无关;其相应的二元酸在相同的色谱条件下,出峰时间与酸酐完全一致。     

涂渍极性及强极性固定相硅膜改性弹性玻璃毛细管柱的研制

本文工作研究了极性、强极性固定液直接涂渍在硅膜改性弹性玻璃毛细管内壁上，经优化温度老化色谱柱，成功地研制出ＯＶ－２２５，ＤＥＧＳ，Ｓｉｌａｒ５，Ｓｉｌａｒ９，Ｓｉｌａｒ１０等硅膜改性弹性玻璃毛细管柱，各种柱子均具有柱效高，热稳定性好的色谱性能。     

SO_4~（2－）／Fe_2O_3－Dy_2O_3催化α－萘乙酸与甲醇酯化反应的色谱法研究

ＳＯ２－４／Ｆｅ２Ｏ３－Ｄｙ２Ｏ３是一种新的稀土改性固体超强酸，研究结果表明它对α－萘乙酸与甲醇酯化反应有很高的催化活性和良好的稳定性。反应混合物在ＮｏｖａｐａｋＣ１８（３．９×１５０ｍｍ，４μ）色谱柱上以甲醇－水（７０∶３０，Ｖ／Ｖ）作流动相８分钟内可实现良好分离。该反应产率高、工艺简便、无腐蚀。     

抑制型离子色谱快速测定I^—,SCN^—,S2O^2—3

本用抑制型离子色谱，薄壳强碱性阴离子交换树脂为分离柱，柱温为３０±１℃，在常规淋洗液ＮａＨＣＯ３－Ｎａ２ＣＯ３中加入对－硝基苯酚作为有机改进剂，测定了Ｉ＾－、ＳＣＮ＾－、Ｓ２Ｏ＾２－３离子。它们有良好的线性关系，三种离子浓度在５．０～３０．０ｍｇ／Ｌ范围内其相关系数分别为：ｒＩ＾－０．９９９４、ｒｓｃｎ＾－０．９９０６、ｒｓ２ｏ＾２－３０．９９８５，检测限分别为：Ｉ＾－０．１７ｍｇ／Ｌ、ＳＣＮ＾     

微分电位溶出法测定人发中铜铜镉锌的研究

本文报道了０．００２５ｍｏｌ．Ｌ＾－１ＨＣｌ－０．２ｍｏｌ．Ｌ＾－１ＮＨ４Ｃｌ底液中连续测定人发中铜、铅、镉、锌的微分电位溶出法。四元素峰电位分别为－０．２０Ｖ，－０．４６Ｖ，－０．６７Ｖ，－１．０２Ｖ（ＳＣＥ），峰形好，灵敏度高，干扰少，测定发样相对标准偏差≤４．３％，回收率为９７．６％－１０４．６％。并对ＨＮＯ３－ＨＣｌＯ４和ＮＨＯ３－Ｈ２Ｏ２消化发样进行了比较。     

气相色谱法测定十二醇聚氧乙烯醚的分子量分布

对非离子表面活性剂十二醇聚氧乙烯醚产品的同在质量－分子量分布的测定方法进行了研究。首先将ＡＥＯ产品进行三甲基硅烷化预处理,采用ＯＶ－１７固定相进行了气相色谱的分析,以标样和文献对照进行了定性与定量,测定结果可以很好地反映出ＡＥＯ产品的分子量分布。     

色谱质谱联用技术研究30%二甲基二乙氧基硅烷70%正硅酸乙酯复合醇盐 …

采用色谱质谱联用技术研究了１种复合醇盐：３０％二甲基二乙氧基硅烷／７０％正硅酸乙酯的水解聚合过程，并由此分析了这两种有机－无机醇盐的相互作用机制和聚合方式，实验结果指出，ＤＤＳ的添加抑制了ＴＥＯＳ的自聚合，使得体系中形成了大量的ＤＤＳ的自聚合环状分子以及ＴＥＯＳ和ＤＤＳ的共聚合高分子，由于后者对水解聚合的加速作用，使得３０％ＤＤＳ／７０％ＴＥＯＳ系统具有最短的凝胶时间。     

微分电位溶出法测定人发中铜铅镉锌的研究

本文报道了０．００２５ｍｏｌ·Ｌ￣（－１）ＨＣｌ－０．２ｍｏｌ·Ｌ￣（－１）ＮＨ＿（４）Ｃｌ底液中连续测定人发中铜、铅、镉、锌的微分电位溶出法。四元素峰电位分别为－０．２０Ｖ，－０．４６Ｖ，－０．６７Ｖ，一１．０２Ｖ（ＳＣＥ），峰形好，灵敏度高，干扰少，测定发样相对标准偏差≤４．３％，回收率为９７．６％～１０４．６％。并对ＨＮＯ＿３－ＨＣｌＯ＿４和ＨＮＯ＿（３）Ｈ＿（２）Ｏ＿２消化发样进行了比较。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.