有机/无机复合介孔膜的合成及其生物酶吸附行为研究

以正硅酸四乙酯(TEOS)为硅源、三嵌段共聚物(F127)为表面活性剂, 聚碳酸酯膜为硬模板, 并采用抽滤法在聚碳酸酯膜内的亚微米级孔道中组装介孔氧化硅从而制备出有机(聚碳酸酯)/无机(介孔氧化硅)复合介孔膜. 通过扫描电镜、能量分散光谱以及透射电镜等实验表征了该有机/无机复合介孔膜的组成、结构及形貌. 研究结果表明: 通过该方法可以在聚碳酸酯膜内孔道中形成长度为9 μm、直径为200 nm的一维氧化硅棒状材料, 且该棒状材料具有无序蠕虫状和有序体心立方的混合介孔结构, 有序体心立方介孔的平均孔径约为8.5 nm. 另外, 初步考察了该复合介孔膜对生物酶的物理吸附行为, 结果表明其对肌红蛋白酶的单位吸附负载量为5.85 mg/g.     

单分散核-壳结构介孔二氧化硅微球的合成

在酸性条件下, 采用非离子表面活性剂嵌段共聚物为模板剂, 季铵盐阳离子表面活性剂为共导向剂, 在预先合成的尺寸均一的单分散实心氧化硅微球表面包裹了有序介孔氧化硅层, 进一步通过高温水热处理, 获得了具有良好分散性和均匀尺寸的介孔壳层(孔径7 nm)氧化硅微球(~500 nm). 氧化硅微球外部包裹的介孔壳层具有较大的比表面积(188 m2/g)和孔容(0.23 cm3/g).     

介孔TiO2对溶菌酶吸附的动力学和热力学

773.15 K下焙烧二钛酸(H₂Ti₂0₅)制备了介孔结构TiO₂。采用比表面分析仪(BET)、扫描电镜(SEM)、拉曼(Raman)光谱和X射线衍射(XRD)仪进行表征研究了介孔TiO₂对溶菌酶的吸附行为和机理。结果表明,该吸附过程较好地满足Langmuir吸附模型;随着溶液pH值的增高,溶菌酶在介孔TiO₂上的吸附量先增大后减小。在pH = 7.2时,达到最大吸附容量72.5 mg·g^-1。该介孔TiO₂对溶菌酶具有良好的吸附稳定性,经过5次循环后吸附的溶菌酶残余量仍有81.6%。动力学研究表明,介孔TiO₂与溶菌酶间的吸附满足准二级动力学模型,吸附传质过程由膜扩散和粒内扩散共同影响与控制。对热力学参数的计算发现,该过程ΔG⁰ < 0, ΔH⁰ > 0, ΔS⁰ > 0,表明介孔TiO₂对溶菌酶的吸附是一个自发的、吸热的熵增过程。     

中空介孔二氧化硅锚固聚偕胺肟吸附Cr(Ⅵ)

以硝酸铈铵为引发剂, 在自制的中空介孔二氧化硅(HMS)的空腔和通道内引发丙烯腈自由基聚合, 并将其氰基偕胺肟化, 用于制备具有吸附Cr(Ⅵ)的廉价有机无机复合吸附材料—中空介孔二氧化硅锚固聚偕胺肟. 通过傅里叶变换红外光谱(FTIR)、 扫描电子显微镜(SEM)及N₂吸附-脱附比表面分析对中空介孔二氧化硅锚固聚偕胺肟进行表征. 结果表明, 制备的中空微球直径约为400 nm, 其壁上孔径约为11.0 nm, 比表面积约为431 m²/g, 锚固聚偕胺肟后中空微球壁上孔道直径约为4.6 nm, 比表面积降低为347 m²/g. HMS锚固的聚偕胺肟对重铬酸钾溶液中铬的吸附量高达0.46 mmol/g, 吸附过程中伴随化学反应, 符合伪二级动力学模型, 可用作废水处理中重金属离子的高效廉价吸附材料.     

利用嵌段共聚物及无机盐合成高质量的立方相、大孔径介孔氧化硅球

使用非离子型嵌段高分子表面活性剂为模板剂,在无机盐的作用下,合成了直 径在2～4 mm、高度有序、立方相的介孔氧化硅SBA-16球。利用无机盐来调变无机 /有机物种之间的作用力和自组装能力,不仅在介观尺寸上提高了所合成介孔材料 的有序程度,而且在宏观上控制了介孔材料的形貌。经焙烧后的SBA-16球材料比表 面积为750 m~2/g,孔容为0.52 cm~3/g,孔径为7.8 nm。具有大孔径的SBA-16球材 料可以更方便地应用于大分子吸附和分离等领域。     

嵌段共聚物与阳离子表面活性剂混合模板合成介孔SiO_2

利用三嵌段共聚物EO_(20)PO_(70)EO_(20)与阳离子表面活性剂CTAB作为混合 模板合成了内部孔结构与外观形貌同时受到调控的介孔氧化硅。与使用单一共聚物 模板制备的介孔氧化硅相比，在混合模板作用下得到的介孔氧化硅的孔结构有序度 降低，而孔径则随混合模板中共聚物的质量分数的降低而减小。在EO_(20)PO_(70) EO_(20)与CTAB质量比为1:1时可得到形貌完好、表面光滑的介孔氧化硅微米球，其 平均孔径为3.2nm，比表面积为972m~2/g。     

载有量子点的介孔二氧化硅微球的制备与性能研究

采用自组装方法制备了一种磁核/介孔二氧化硅壳的微球, 调节体系中C₁₈TMS的加入量可控制介孔硅球的比表面积; 并通过化学修饰的方法对介孔微球表面进行巯基功能化修饰. 利用巯基与量子点之间的相互作用可将一定尺寸的量子点吸附于介孔二氧化硅球的孔中, 令介孔微球具有荧光效应; 同时可以利用吸附不同粒径的量子点的荧光光谱对介孔二氧化硅微球孔径的大小进行近似考察.     

二元阴阳离子表面活性剂法合成介孔氧化硅囊泡

以十二烷基磺酸钠(SDS)和十六烷基三甲基溴化铵(CTAB)为表面活性剂, 在SDS与CTAB的摩尔比为1.0~2.3时, 以正硅酸乙酯(TEOS)为硅源, 在氨水-水体系中于68℃下合成介孔氧化硅囊泡. 通过透射电子显微镜(TEM)、 X射线衍射仪(XRD)、 热重分析仪(TGA)和氮气吸附-脱附实验仪对合成的产物进行表征. 结果表明, 合成的产物为介孔氧化硅囊泡聚集体, 孔径约为4 nm, 样品的Brunauer-Emmett-Teller(BET)比表面积为826 m²/g. 对介孔氧化硅囊泡的形成机理做了初步探讨.     

Ag/mSiO2空心微球的制备及SERS标记性能

以聚苯乙烯微球为模板, 经过原位还原和种子生长过程在聚苯乙烯微球表面包覆银(Ag)纳米粒子; 以正硅酸乙酯为硅源, 在十六烷基三甲基溴化铵的导向下实现介孔二氧化硅(mSiO₂)可控包覆, 去除模板得到Ag/mSiO₂空心微球. 透射电子显微镜(TEM)和氮气吸附-脱附分析结果表明, SiO₂壳层厚度约为20 nm, 介孔孔径为2.1 nm, 孔道分布均匀. 进一步利用虹吸作用使对巯基苯胺(4-ATP)分子进入微球内与Ag粒子结合, 构建表面增强拉曼散射(SERS)标记材料. SERS测试结果表明, 该标记材料检测限达到10^-7 mol/L, SERS增强因子达到3.7×10⁵.     

具有碱催化活性的有序氮氧化硅MCM-41介孔分子筛的制备与性能研究

以介孔氧化硅MCM-41为氮化前驱体, 以纯的氨气为氮源, 通过调节氮化工艺参数, 制备出了氮含量高达23.01 wt%、比表面积高达665.4 m²•g^－1、平均孔径为2.5 nm的氮氧化硅有序介孔分子筛材料. 采用CNH元素分析、N₂吸附- 脱附分析、小角XRD、高分辨透射电镜(HRTEM)、红外光谱以及²⁹Si 固体核磁共振谱(MAS NMR)等技术对材料的结构进行系统的研究. 并且通过苯甲醛和丙二腈的缩合反应研究了该类材料的碱催化活性. 研究表明, 在30 ℃反应3 h后苯甲醛的转化率达到99.9%.     

Mesoporous silica spheres from colloids

A novel method has been developed to synthesize mesoporous silica spheres using commercial silica colloids (SNOWTEX) as precursors and electrolytes (ammonium nitrate and sodium chloride) as destabilizers. Crosslinked polyacrylamide hydrogel was used as a temporary barrier to obtain dispersible spherical mesoporous silica particles. The influences of synthesis conditions including solution composition and calcination temperature on the formation of the mesoporous silica particles were systematically investigated. The structure and morphology of the mesoporous silica particles were characterized via scanning electron microscopy (SEM) and N2 sorption technique. Mesoporous silica particles with particle diameters ranging from 0.5 to 1.6 microm were produced whilst the BET surface area was in the range of 31-123 m2 g-1. Their pore size could be adjusted from 14.1 to 28.8 nm by increasing the starting particle diameter from 20-30 nm up to 70-100 nm. A simple and cost effective method is reported that should open up new opportunities for the synthesis of scalable host materials with controllable structures.     

Studies on mesoporous niobosilicates synthesized using F127 triblock copolymer

A detailed characterization of cage-like mesoporous SBA-16 niobosilicate with tailored features of the structure is reported. The materials were synthesized in a EO₁₀₆PO₇₀EO₁₀₆(F127)-water system under acidic conditions and the pore diameters were tuned by varying the hydrothermal treatment temperature and time. The effects of the synthesis parameters on the structural/textural properties of the cubic Im3m niobosilicates have been investigated systematically. We show that the total pore volume, pore diameter, and micro-/mesopores ratio can be controlled very efficiently by changing the synthesis parameters.     

几种手性醇在纤维素键合的SBA-15基手性固定相上的直接拆分

在强酸性条件下, 以三嵌段聚醚P123为模板, 合成了孔径大且粒径均匀的SBA-15介孔二氧化硅微球. 将含有少量三乙氧硅丙基氨基甲酸酯残基的纤维素-三(3,5-二甲基苯基氨基甲酸酯)通过分子间缩聚作用固载到氨丙基化的SBA-15微球上, 制得手性固定相; 采用常规和非常规的流动相模式, 对一些芳香醇的消旋体进行了手性拆分. 实验结果表明, 所制备的SBA-15微球不仅分散性良好, 具有规则的二维六方孔道结构, 而且消除了微孔; 所制备的键合手性固定相不仅固载手性选择剂的量大, 而且经六甲基二硅胺烷封端后可有效改善拖尾现象, 对实验选用的手性醇具有较高的拆分能力; 与大孔硅胶为基质的同类纤维素键合手性固定相相比, 该固定相对同种手性消旋体的分离因子明显提高.     

General Information to Obtain Spherical Particles with Ordered Mesoporous Structures

Conditions for the synthesis of aluminum organophosphonate (AOP) and aluminophosphate (AlPO) spheres containing periodic mesopores were optimized and demonstrated to be general morphological controls for the surfactant‐assisted synthesis of mesoporous materials. High‐quality AOP and AlPO spheres with uniform mesopores were obtained at low and high temperatures, respectively. The aerosol‐assisted synthesis of materials with uniform mesopores was categorized by using the difference in relative density of soluble AOP and AlPO oligomers that interact with ethylene oxide (EO) units in EO_nPO_mEO_n triblock copolymer (PO=propylene oxide). Then, ordered mesoporous structures are constructed with the adequate amount of species in resultant frameworks, and the number of interactive points in soluble species determines the resultant density of the frameworks after self‐assembly. Consequently, temperature‐dependent synthesis, which allows controlled infiltration of soluble species to match the density of resultant frameworks, is required for the formation of ordered mesoporous structures under morphological control.     

Synthesis and characterization of pore size-tunable magnetic mesoporous silica nanoparticles

Magnetic mesoporous silica nanoparticles (M-MSNs) are emerging as one of the most appealing candidates for theranostic carriers. Herein, a simple synthesis method of M-MSNs with a single Fe(3)O(4) nanocrystal core and a mesoporous shell with radially aligned pores was elaborated using tetraethyl orthosilicate (TEOS) as silica source, cationic surfactant CTAB as template, and 1,3,5-triisopropylbenzene (TMB)/decane as pore swelling agents. Due to the special localization of TMB during the synthesis process, the pore size was increased with added TMB amount within a limited range, while further employment of TMB lead to severe particle coalescence and not well-developed pore structure. On the other hand, when a proper amount of decane was jointly incorporated with limited amounts of TMB, effective pore expansion of M-MSNs similar to that of analogous mesoporous silica nanoparticles was realized. The resultant M-MSN materials possessed smaller particle size (about 40-70 nm in diameter), tunable pore sizes (3.8-6.1 nm), high surface areas (700-1100 m(2)/g), and large pore volumes (0.44-1.54 cm(3)/g). We also demonstrate their high potential in conventional DNA loading. Maximum loading capacity of salmon sperm DNA (375 mg/g) was obtained by the use of the M-MSN sample with the largest pore size of 6.1 nm.     

Synthesis and Characterization of Ordered Mesoporous Silica Spheres Using Anionic and Nonionic Mixed Surfactants for Their Potential Application in LC

Ordered mesoporous silicas (OMSs) with spherical morphology were synthesized by using mixed surfactants of anionic sodium dodecyl sulfate and nonionic block copolymer EO₂₀PO₇₀EO₂₀ (P123) as template through an acid-catalyzed silica sol?Cgel process. A variety of characterizations demonstrated that the silica products exhibited well-formed spherical morphology, ordered mesostructure, narrow pore size distribution and large surface area (~700 m² g^?1). It was found that the synthesized OMSs had high adsorption capacity by using oxymatrine as model solute. The column packed with the silica spheres exhibited low back pressure and baseline separation of aromatic compounds such as benzene and nitrobenzene could be achieved. These results demonstrated the synthesized OMSs as a potential stationary phase for liquid chromatography.     

Highly aminated mesoporous silica nanoparticles with cubic pore structure

Mesoporous silica with cubic symmetry has attracted interest from researchers for some time. Here, we present the room temperature synthesis of mesoporous silica nanoparticles possessing cubic Pm3?n symmetry with very high molar ratios (>50%) of 3-aminopropyl triethoxysilane. The synthesis is robust allowing, for example, co-condensation of organic dyes without loss of structure. By means of pore expander molecules, the pore size can be enlarged from 2.7 to 5 nm, while particle size decreases. Adding pore expander and co-condensing fluorescent dyes in the same synthesis reduces average particle size further down to 100 nm. After PEGylation, such fluorescent aminated mesoporous silica nanoparticles are spontaneously taken up by cells as demonstrated by fluorescence microscopy.     

Facile method to synthesize platelet SBA-15 silica with highly ordered large mesopores

Highly ordered mesoporous SBA-15 silica with large pore diameter of 18 nm (nominal BJH pore diameter ~22 nm) and short pore length (~500 nm) was synthesized using a micelle expander 1,3,5-triisopropylbenzene in the absence of ammonium fluoride by employing short initial stirring time at 17 °C followed by static aging at low temperature. Scanning and transmission electron microscopies revealed that the material comprised of platelet particles in which large mesopores were nearly flawlessly arranged within uniform domains up to 3 μm in size. The platelet SBA-15 had the (100) interplanar spacing of 17 nm, high surface area (~470 m(2) g(-1)) and large pore volume (~1.6 cm(3) g(-1)). The hydrothermal treatment at 130 °C for 2 days was employed to eliminate constrictions from the pore channels. The control experiment showed that a sample prepared with prolonged stirring had very similar mesoporous properties, but the particle size was smaller and the domains were irregular, proving that the static conditions facilitate the formation of SBA-15 with platelet particle morphology. The absence of ammonium fluoride was also critical in attaining the platelet particle shape.     

Fabrication and characterization of hexagonal mesoporous silica monolith via post-synthesized hydrothermal process

Large-sized, optical transparent mesostructured Brij 56/silica monolith has been fabricated using a lyotropic liquid crystal of Brij 56 (C₁₆EO₁₀) as a template and TMOS as a silica source, combined with a optimizing sol-gel process and a hydrothermal aging process. By programmed temperature drying and calcinations, translucent mesoporous silica monolith with two-dimensional hexagonal structure (P6mm) has bee obtained. The ordered mesoporous silica monoliths have been characterized by small-angle X-ray diffraction, transmission electron microscopy (TEM), and nitrogen adsorption, which shows that the materials have a highly ordered two-dimensional hexagonal mesostructure with the high specific surface area of 837 m² · g⁻¹ and narrow pore distribution with a mean BJH pore diameter of 2.73 nm. Based on calculations and differential scanning calorimetry and thermogravimetric analyses, the action mechanism of the hydrothermal aging process has been proposed: the 100°C hydrothermal conditions and autogenous 2.3 atm pressure promote the condensation and dehydration of silanol groups, with the result that cross-linking degree, the flaws and moisture content in gels are reduced notably. Those processes guarantee the integrity of gels in the following drying process.