二茂铁-Nafion修饰葡萄糖传感器的研究

1 引言 第二代电流式酶传感器采用非生理的氧化还原介体如二茂铁及其衍生物、铁氰化钾、四硫富瓦烯、醌及其衍生物、钉化合物及麦尔多蓝等代替氧,起着酶与电极之间的电子传递作用,克服了第一代电流式酶传感器背景电流大,响应特性差,易受环境中氧浓度的影响,干扰大等缺点。但目前第二代电流式酶电极还存在着介体流失,电极污染及一些电活性物质干扰等问题。商品化的Nafion甲醇溶液不易溶解酶且能使部分酶失活,本文把Nafion甲醇溶液制成Nafion水溶液,将葡萄糖氧化酶溶解在Nafion水溶液,然后把它修饰在修饰有二茂铁的玻碳电极的表面,最后再修饰一层Nafion膜,成功地制备了二茂铁-Nafion修饰葡萄糖传感器,Nafion膜不仅能把抗坏血酸、尿酸等电活性物质阻挡在电极外,防止其干扰,同时具有防污性能,而且能防止二茂铁的流失,提高电极的稳定性。该传感器具有抗干扰能力强,响应快等特点。     

以Nafion修饰的镀铂玻碳电极为基底的半乳糖传感器的制备

在镀铂的玻碳电极表面,修饰一层全氟代磺酸酯(Nafion)膜,制成基底电极。用化学交联法将半乳糖氧化酶(GAD)固定在基底电极表面,即制成半乳糖传感器。和光亮铂相比,镀铂电极对过氧化氢有更高的响应,而Nafion膜可以消除抗坏血酸,尿酸等电活性物质对测定的影响,提高了酶电极测定的选择性。D-半乳糖测定的线性范围为0.25～4.25 mmol/L,响应时间小于30s。电极连续使用300次,没有明显的电流变化。该电极具有快速、准确,选择性高的特点。     

烟酰胺辅酶在聚甲苯胺蓝膜修饰的玻碳电极上的电催化氧化

用循环伏安法在玻碳电极上电沉积一层稳定的甲苯胺蓝聚合物膜 ,研究了这层膜在 0 .2mol/L磷酸缓冲溶液 (pH 6 .86 )中的电化学性质 ,并且考察了该膜修饰的玻碳电极对烟酰胺辅酶 (NADH)的电催化作用 ,用旋转圆盘电极测量了NADH在该修饰电极上的催化反应常数。实验发现 ,在该修饰电极上 ,NADH氧化峰电位比未修饰的玻碳电极负移了 4 5 0mV ,且其催化反应速率常数为 3.5× 10 3 L·mol-1·s-1,说明聚甲苯胺蓝膜对NADH有良好的电催化作用     

基于多壁碳纳米管/壳聚糖多层膜修饰玻碳电极邻苯二酚的测定

改进了碳纳米管在壳聚糖溶液中的分散方法,制备了多壁碳纳米管/壳聚糖多层膜修饰玻碳电极,对比了不同修饰层数膜电极的循环伏安和电化学阻抗行为,5层多壁碳纳米管/壳聚糖膜修饰玻碳电极的电化学性能优良.在最优实验条件下,该修饰玻碳电极对邻苯二酚(CAT)有灵敏的响应,CAT浓度在3.99×10-6～9.09×10-4mol/L范围内与氧化峰电流呈良好的线性关系,检出限为2.39×10-6mol/L(S/N=3).该修饰玻碳电极性能稳定,测定4×10-5mol/LCAT溶液,RSD(n=10)为2.1%;15周后,该电极的响应值仅降低1.9%.     

天青Ⅰ修饰玻碳电极的电化学性质及其对NADH的催化氧化

本文利用滴涂于玻碳表面的Nafion膜中负电性的磺酸基与天青I阳离子之间的静电作用,以实现天青I的固定化,从而制备出Nafion/天青I电催化型烟酰胺腺嘌呤二核苷酸(NADH)传感器。采用循环伏安法考察了传感器的电化学性质,并研究了该修饰电极对NADH的电催化作用。实验结果表明:该修饰电极对NADH有良好的电催化作用,NADH氧化峰电位比未修饰的玻碳电极负移了660 mV,响应电流与NADH的浓度在8.7×10-5~1.5×10-2mol/L范围内呈良好的线性关系。该方法检出限为3.0×10-5mol/L。     

肌红蛋白在Nafion/Fe3O4- CdTe/CdS量子点复合膜内的直接电化学及其应用于H2O2的生物传感

利用磁性纳米Fe3O4和CdTe/CdS量子点结合Nafion的良好成膜性,将肌红蛋白(Mb)固定在玻碳 电极表面制备成Nafion/Fe3O4 - CdTe/CdS - Mb/GCE修饰电极.在pH 7.0的0.1 mol/L磷酸盐缓冲溶液 (PBS)中,固定在膜内的Mb表现出良好的直接电化学性质,在-0.351...     

硫堇/Nafion/石墨烯修饰电极对NADH的电催化活性研究

为了提高电化学检测NADH的分析性能,制备了硫堇/Nafion/石墨烯修饰的玻碳电极(GCE),利用Nifion的强离子交换能力将硫堇修饰在电极表面,形成硫堇/Nafion/石墨烯复合电极.与裸玻碳电极相比,在NADH的反应中观察到了电位明显降低和电流响应显著增大.证实了硫堇/Nafion/石墨烯复合电极对NADH有协同的电催化能力.为构造有效地检测NADH的电化学传感器提供一个良好的应用平台.     

联吡啶钌/氮掺杂石墨烯/Nafion复合修饰电极电化学分析盐酸异丙嗪的研究

本文采用电化学性能独特的联吡啶钌(Ru(bpy)32+)、氮掺杂石墨烯(NG)和Nafion膜构建了一种新型的盐酸异丙嗪电化学传感器。采用红外光谱和扫描电子显微镜对氮掺杂石墨烯的形貌进行了表征。在Nafion膜中添加导电性好、比表面积大的氮掺杂石墨烯可以增加电子传递速度并且可以防止联吡啶钌扩散到Nafion膜的非电活性区域而增加电极使用寿命。在p H 7.0的磷酸盐缓冲溶液中,盐酸异丙嗪在Ru(bpy)32+/NG/Nafion修饰电极上的循环伏安曲线表明,与单一的裸玻碳电极、Ru(bpy)32+/Nafion修饰电极以及NG/Nafion修饰电极相比,该修饰电极使盐酸异丙嗪得氧化峰电流显著增加,而峰电位明显负移,表明采用Ru(bpy)32+/NG/Nafion膜制备的复合修饰电极对盐酸异丙嗪呈现出较强的电化学催化作用。优化实验条件后,发现在1.0×10-6mol·L-1~1.0×10-4mol·L-1.浓度范围内,盐酸异丙嗪的氧化峰电流与其浓度呈良好的线性关系,检测限为3.6×10-7mol·L-1。而且该电极的重现性、稳定性和选择性良好,采用标准加入法可成功用于商业盐酸异丙嗪注射液中盐酸异丙嗪的测定。     

CdTe量子点修布电极的阳极电致化学发光

制备了CdTe量子点/Nafion修饰玻碳电极(CdTe QDs/Nafion/GCE),并研究了该修饰电极在中性磷酸盐缓冲溶液(PBS)中的电致化学发光(ECL)行为.结果表明,三丙胺(TPA)作为共反应剂存在时,QDs/Nafion/GCE在中性PBS中可以产生强的阳极电化学发光信号.考察了量子点的用量、Nafion的用量、pH、电解质等条件对ECL的影响.抗坏血酸对QDs/Nafion/GCE的ECL具有抑制作用,且抑制程度与抗坏血酸浓度呈线性关系,为利用电致化学发光法检测抗坏血酸提供了新方法.     

六氰合铁酸锰铬修饰电极的制备及其电化学行为

应用循环伏安法在活化玻碳电极(GCE)表面制备六氰合铁酸锰铬(MnCrHCF)膜修饰电极(MnCrH-CF/GCE)并研究其电化学性质.探讨影响膜电沉积的因素,研究pH值以及不同支持电解质等制备条件对该修饰电极性能的影响,优化制备工艺,分析其反应机理.     

乙酰胆碱酯酶/Nafion/普鲁士蓝修饰玻碳电极的制备及其在有机农药检测中的应用

制备了乙酰胆碱酯酶/Nafion/普鲁士蓝修饰的玻碳电极,测试了该修饰电极检测有机农药西维因(carbaryl)和敌百虫(trichlorfon)的性能指标。 利用原子力显微镜和电化学技术研究了电极的构造及其对于有机农药检测性能指标的影响。 结果表明,乙酰胆碱酯酶均匀地分散到Nafion/普鲁士蓝修饰的玻碳电极上。 在最优的实验条件下,构筑的修饰电极检测西维因和敌百虫的线性范围分别为0.01~0.5 μmol/L及2.0~10.0 μmol/L和0.02~1.0 μmol/L及2.0~8.0 μmol/L,检出限分别为5.0和10.0 nmol/L。 并对模拟的实际样品进行了检测,发现该方法有较高的检测灵敏度、较好的重复性和抗干扰性。     

Differential pulse anodic stripping voltammetric determination of traces of copper with a tobramycin-Nafion modified electrode.

A Nafion-modified glassy carbon electrode incorporated with tobramycin for the voltammetric stripping determination of Cu2+ has been explored. The electrode was fabricated by tobramycin containing Nafion on the glassy carbon electrode surface. The modified electrode exhibited a significantly increased sensitivity and selectivity for Cu2+ compared with a bare glassy carbon electrode and the Nafion modified electrode. Cu2+ was accumulated in HAc-NaAc buffer (pH 4.6) at a potential of -0.6 V (vs. SCE) for 300 s and then determined by differential pulse anodic stripping voltammetry. The effects of various parameters, such as the mass of Nafion, the concentration of tobramycin, the pH of the medium, the accumulation potential, the accumulation time and the scan rate, were investigated. Under the optimum conditions, a linear calibration graph was obtained in the concentration range of 1.0 x 10(-9) to 5.0 x 10(-7) mol l(-1) with a correlation coefficient of 0.9971. The relative standard deviations for eight successive determinations were 4.3 and 2.9% for 1.0 x 10(-8) and 2.0 x 10(-7) mol l(-1) Cu2+, respectively. The detection limit (three times signal to noise) was 5.0 x 10(-10) mol l(-1). A study of interfering substances was also performed, and the method was applied to the direct determination of copper in water samples, and also in analytical reagent-grade salts with satisfactory results.     

一氧化氮在Nafion-钴席夫碱膜修饰电极上的电催化氧化及其测定

将一种杂环席夫碱N,N′-2 ,6 -二乙酰吡啶缩双苯胺和Nafion修饰在铂电极上 ,然后与钴 (Ⅱ )反应 ,得到Nafion -钴席夫碱膜修饰电极。实验结果表明 ,该修饰电极具有良好的机械、化学和电化学稳定性 ,对生物分子一氧化氮的电化学氧化有显著的催化作用。以1.5次微分线性扫描伏安法测定一氧化氮 ,当浓度在2.8×10-6～8.4×10-8 mol/L范围时 ,氧化电流与浓度有良好的线性关系 ,抗坏血酸、精氨酸及亚硝酸根不干扰测定。     

Cuprous Oxide/Nitrogen-doped Graphene Nanocomposites as Electrochemical Sensors for Ofloxacin Determination

Cu₂O/nitrogen-doped grapheme(NG) nanocomposite material was prepared via a facile one step chemical reduction and characterized by means of X-ray diffraction(XRD) and scanning electron microscopy(SEM). A new electrochemical sensor was then fabricated by coating Cu₂O/nitrogen-doped graphene nanocomposite with Nafion on glassy carbon electrode(Cu₂O/NG/Nafion/GCE). The electrochemical response of this modified electrode toward ofloxacin was examined by cyclic voltammetry. The results indicate that Cu₂O/NG/Nafion composite-modified electrode exhibits higher catalytic activity in the electrochemical oxidation of ofloxacin compared with glassy carbon electrode(GCE), Cu₂O/Nafion modified electrode(Cu₂O/Nafion/GCE), and N-doped graphene/Nafion modified electrode(NG/Nafion/GCE). Under optimal conditions, the peak current was found to be linearly proportional to the concentration of ofloxacin in the 0.5-27.5 μmol/L and 27.5-280 μmol/L ranges with a lower detection limit of 0.34 μmol/L, higher sensitivity of 39.32 μA·L·mmol^-1 and a shorter reaction time of less than 2 s. In addition, Nafion can enhance the stability of the modified electrode and prevent some negative species. Thus the modified electrode exhibits good selectivity and a long working life. The Cu₂O/NG/Nafion composite modified electrode shows promising application in electrochemical sensors, biosensors, and other related fields because of its excellent properties.     

微过氧化物酶-11修饰电极对O2和H2O2的电催化还原

运用电化学循环伏安法和旋转圆盘电极技术研究了Ｏ２和Ｈ２Ｏ２在Ｎａｆｉｏｎ膜固定的微过氧化物酶－１１修饰的玻磷（ＭＰ－１１＋Ｍａｆｉｏｎ／Ｇｃ）电极上的电化学还原,结果表明,饰电极 对Ｏ２和Ｈ２Ｏ２的还原均具电催化作用。测定和比较了Ｏ２和Ｈ２Ｏ２在ＭＰ－１１＋Ｎａｆｉｏｎ／ＧＣ的电极上电催化还原反应的一些动力学参数。发现Ｏ２在修饰电极上经历了四电子还原,且还原过程与溶液的ＰＨ值有关。     

Electrochemical and electrocatalytic behaviors of Safranin O/Nafion film deposited on the glassy carbon electrode

The glassy carbon (GC) electrode modified with Nafion and Safranin O (SFO) was prepared and its electrochemical properties were investigated. The SFO molecules were strongly and irreversibly adsorbed on the Nafion — modified GC surface. The electrochemical behavior and mechanism for interactions of the SFO molecules with the Nafion film were investigated through cyclic voltammetric method. The electrocatalytic reduction of nitric oxide was performed at this modified electrode by cyclic voltammetric and hydrodynamic amperometric techniques. The Nafion membrane played a duel role as a matrix for the SFO immobilization and also helped to partition the nitric oxide from the solution phase. The diffusion coefficient of NO at the SFO/Nafion/GC modified electrode was calculated using chronoamperometry. The dependence of response currents on the concentration of NO was examined and was linear in the range of 0.05–1.9 mM of NO.     

基于Nafion/碳纳米粒子修饰的葡萄糖传感器

采用滴涂法制备了Nafion/碳纳米粒子复合物修饰玻碳电极,该电极对H2O2具有良好的电催化氧化性能。还利用滴涂法制备了Nafion/碳纳米粒子复合物包裹的葡萄糖酶电化学生物传感器,该生物传感器对葡萄糖有着良好的电催化作用。应用该传感器对葡萄糖进行了检测,检测线性范围为2.0×10-6～6.0×10-3mol/L,检出限为1.6×10-6mol/L(S/N=3),实验结果表明该传感器具有良好的稳定性、重现性和抗干扰能力。对小鼠血清样品中的葡萄糖进行检测,结果令人满意。     

A glucose biosensor using methyl viologen redox mediator on carbon film electrodes

A new methyl viologen-mediated amperometric enzyme electrode sensitive to glucose has been developed using carbon film electrode substrates. Carbon film electrodes from resistors fabricated by pyrolytic deposition of carbon were modified by immobilization of glucose oxidase through cross-linking with glutaraldehyde in the presence of bovine serum albumin. The mediator, methyl viologen, was directly immobilised with the enzyme together with Nafion cation-exchange polymer. The electrochemistry of the glucose oxidase/methyl viologen modified electrode was investigated by cyclic voltammetry and by electrochemical impedance spectroscopy. The biosensor response to glucose was evaluated amperometrically; the detection limit was 20 μM, the linear range extended to 1.2 mM and the reproducibility of around 3%. When stored in phosphate buffer at 4 °C and used every day, the sensor showed good stability over more several weeks.     

Nafion/tetraruthenated porphyrin glassy carbon-modified electrode: characterization and voltammetric studies of sulfite oxidation in water–ethanol solutions

In this work, the modification of a glassy carbon electrode with tetraruthenated porphyrins electrostatically assembled onto a Nafion film, previously adsorbed on the electrode surface, is reported. This modified electrode was characterized by scanning electron microscopy–energy-dispersive X-ray, Raman spectroscopy, UV-Vis spectroelectrochemistry, and cyclic voltammetry. The Nafion film onto the glassy carbon electrode shows a smooth disposition; when the tetraruthenated porphyrin is incorporated on the Nafion film, the complex is adsorbed in a homogeneous way. The modified electrode catalyzes HSO₃⁻ oxidation in water–ethanol solutions and shows an enhanced stability compared with the electrode modified with the dip coating method. Rotating disk electrode experiments showed a kinetic limitation to the electron transfer controlled by charge propagation in the film. I/E curves show a Tafel slope of 120 mV/decade corresponding to a first electron-transfer reaction, depending on the potential, as the determining step. Spectroelectrochemical experiments demonstrated that Ru(II) is the active site for the electrocatalysis.     

Rapid amperometric detection of coliforms based on MWNTs/Nafion composite film modified glass carbon electrode

A multi-wall carbon nanotubes (MWNTs)/Nafion modified glassy carbon electrode (GCE) was fabricated for the rapid amperometric detection of coliforms, represented by Escherichia coli (E. coli). In the bacterial solution, beta-galactosidase which was used as an indicator of coliforms reacted with substrate, p-aminophenol-beta-galactopyranoside (PAPG), and produced p-aminophenol (PAP). PAP was detected by MWNTs/Nafion modified GCE. Due to the cation-exchange capacity of Nafion and the electrocatalytic ability of MWNTs, the detection sensitivity of PAP was improved and the detection time of coliforms was shortened. The bacterial can be detected within 5h ranging from 10 to 10(4)cfu/mL. The MWNTs/Nafion modified GCE was easy to be constructed and regenerated. To our best knowledge, it was the first time to use MWNTs/Nafion modified GCE to detect the concentration of coliforms.