多波长线性回归紫外吸光光度法同时测定炼油厂污水中苯酚和苯胺

提出用多波长线性回归紫外吸光光度法同时测定炼油厂污水中的苯酚和苯胺.方法省去了萃取、蒸馏、显色等步骤,操作简单.对合成水样进行测定,相对标准偏差≤4.57%,相对误差≤±2.3%.对炼油厂水样进行测定并进行加标回收试验,苯酚和苯胶的回收率分别为99.4%～103.0%和97.2%～104.0%,结果良好.苯酚和苯胶的最低检出限分别为0.010和0.048μg·ml~(-1).     

停流-抑制动力学荧光法测定痕量苯酚

用停流技术研究了在H2SO4介质中,苯酚抑制BrO-3氧化丁基罗丹明B荧光猝灭反应,并探讨了反应机理。基于苯酚对该反应诱导期的影响作用,建立了停流-抑制动力学荧光法测定痕量苯酚的新方法。方法的检出限为1.4×10-8g.L-1,线性范围为0.4~15.0μg.L-1,11次测定7.0μg.L-1苯酚的相对标准偏差为2.1%。本法灵敏、简便,用于测定制药废水和番茄酱样品中痕量苯酚,结果满意。     

流动注射化学发光法测定工业废水中苯酚

采用流动注射技术,研究了高锰酸钾-过氧化氢-苯酚的化学发光行为,对影响化学发光强度的因素进行了试验,建立了流动注射化学发光法测定苯酚的方法。方法的检出限为3×10-5g.L-1,线性范围为1.0×10-4~1.0×10-1g.L,对浓度为4.0×10-4g.L的苯酚作试验,求得其相对标准偏差(n=11)值为1.6%。方法用于废水中苯酚含量的测定,结果与分光光度法测得值一致。     

高效液相色谱法同时测定染发剂中11种氨基苯酚

建立了高效液相色谱测定直接型与氧化型染发剂中11种氨基苯酚含量的分析方法。样品在亚硫酸氢钠的保护下用甲醇提取,高速冷冻离心净化;采用Agilent Zorbax SB C18色谱柱分离,流动相为5 mmol/L庚烷磺酸钠-40 mmol/L pH 2.8磷酸盐缓冲液和乙腈,梯度洗脱,11种氨基苯酚分别于230、270和400 nm下检测。11种氨基苯酚在0.05～500 mg/L线性范围内相关系数不小于0.9992,4-氨基-3-硝基苯酚、2-氨基-5-硝基苯酚、3-硝基-4-(2-羟乙基)氨基苯酚的方法定量限为5 mg/kg,其他8种氨基苯酚包括对氨基苯酚、对甲氨基苯酚、间氨基苯酚、邻氨基苯酚、5-氨基-2-甲基苯酚、4-氨基-3-甲基苯酚、2-甲基-5-(2-羟乙基)氨基苯酚和2-氨基-4-硝基苯酚定量限为20 mg/kg,方法回收率为88.5%～109.5%,相对标准偏差为2.2%～8.3%。测定了多种市售染发剂,结果表明该方法操作简单、测定结果准确,可用于直接型与氧化型染发剂中11种氨基苯酚的测定。     

阻抑高碘酸钾氧化甲基紫褪色光度法测定苯酚

基于HAc-NaAc缓冲体系中,反应温度为25℃时,苯酚阻抑高碘酸钾氧化甲基紫的褪色反应,建立了测定苯酚的阻抑褪色光度新方法.该方法最大吸收波长为580 nm,线性范围为0.02μg/mL～2·2μg/mL,检出限为3.8×10<'-3>μg/mL,方法用于环境水中苯酚的测定,相对标准偏差为1.97%～2.25%,回收...     

间接法测定工业废水中微量苯酚

研究了用吸光光度法间接测定微量苯酚的方法。在KBrO3和KBr溶液中,以淀粉 碘化钾为显色剂,最大吸收波长为590nm,线性范围为0.10～2.00mg·L-1,回收率为92%～110%,NH+4、Ca2+、Fe3+等不干扰测定。该法用于测定工业废水中痕量苯酚,结果满意。     

高效液相色谱法同时测定2,4-二硝基苯酚钾对-硝基苯酚钾和邻-硝基苯酚钾

2,4-二硝基苯酚钾、对-硝基苯酚钾和邻-硝基苯酚钾等原料混配,用作植物生长调节剂.目前,关于这三种成分同时测定的方法未见报道.经试验研究,采用反相高效液相色谱法在同一分析条件下同时测定三种有效成分,操作简便、准确度高、精密度好,适于工业生产及产品质量监督的需要.1 试验部分1.1 仪器与试剂岛津LC—10A高效液相色谱仪SPD—10A紫外检测器2,4-二硝基苯酚、对-硝基苯酚、邻-硝基苯酚:纯度均为99.5%     

酶催化荧光法测定环境水样中的痕量苯酚

利用苯酚对血红蛋白模拟酶催化H2O2和L-酪氨酸荧光体系的猝灭作用,建立了酶催化荧光法测定痕量苯酚的新方法。研究了该猝灭反应的最佳实验条件,其猝灭程度与苯酚的浓度成线性关系。测定的线性范围为3.0~70μmol/L,检出限为1.64μmol/L。对浓度为15μmol/L的苯酚标准溶液进行了11次平行测定,其相对标准偏差为3.0%。方法可用于环境水样中苯酚含量的测定。     

气相色谱–质谱法测定食品接触材料聚苯醚中2,6-二甲基苯酚的迁移量

建立食品接触材料聚苯醚中2,6-二甲基苯酚迁移量的气相色谱–质谱检测方法。将聚苯醚样品加至食品模拟液中,于60℃下迁移2 h,再用乙酸乙酯提取。进样口温度为180℃,初始温度为80℃,保持2 min,以20℃/min升温至200℃,保持2 min,再升温至240℃,经DB–WAX气相色谱柱(30 m×0.25 mm,0.25μm)分离,质谱法测定,以保留时间定性,外标法定量。2,6-二甲基苯酚的质量浓度在0.01～0.5 mg/L范围内与色谱峰面积呈良好的线性关系,线性相关系数为0.999 9,方法检出限为0.01 mg/L。用4%乙酸、10%乙醇、95%乙醇和异辛烷分别进行加标回收试验,方法的回收率为91.7%～104.5%,测定结果的相对标准偏差为1.11%～4.63%(n=6)。该方法为检测食品接触材料中2,6-二甲基苯酚迁移含量测定提供了准确、可靠的方法。     

支持向量回归-分光光度法对苯酚、苯胺和苯甲酸的同时测定

用支持向量回归(SVR)结合分光光度法对苯酚、苯胺、苯甲酸进行了同时测定.在230～300 nm的波长范围内,用SVR方法建立校正模型,用留一交叉验证的方法优化SVR方法建模,并对苯酚、苯胺、苯甲酸的模拟样品进行了测定.苯酚、苯胺、苯甲酸的预测结果的回收率在98.1%～101.1%之间.     

A carbanion induced synthesis of highly congested pyrazole and imidazole containing heterocycles

An efficient approach to the synthesis of highly congested di, penta and hexacyclic pyrazoles as well as imidazole fragment containing novel heterocyclic molecule has been developed through a carbanion induced transformation of suitably functionalized 2H-pyran-2-ones, benzo[h]chromene and thiochromeno[4,3-b]pyrans. Due to the presence of fluorescence, we report their prime application metal sensor as off/on switching in ferric ions.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Selective synthesis of 4,5-dihydroimidazo- and imidazo[1,5-a]quinoxalines via modified Pictet–Spengler reaction

An efficient tandem approach for the selective synthesis of 4,5-dihydroimidazo[1,5-a]quinoxalines 6a–g and imidazo[1,5-a]quinoxalines 7a–h by the reaction of 2-imidazolyl anilines 4a–c with aryl aldehydes 5a–k under mild reaction conditions is described. Introduction of electron releasing alkyl groups in substrates 4a–b was found to be instrumental for the success of the reaction.     

Understanding the Diels-Alder reactivity of 1,2-azaborine analogues

The Diels-Alder reactivity of 1,2-heteroborines (H₄C₄B(H)X, X?=?NH, PH, AsH; O, S, Se) has been computationally explored by means of Density Functional Theory (DFT) calculations. The influence of the HB?=?X fragment on the reactivity of the system has been quantitatively analyzed in detail by means of the so-called Activation Strain Model (ASM) of reactivity. It is found that the interaction between these species and the dienophile is significantly stronger than that computed for their all-carbon isoelectronic counterpart, benzene. In addition, the strain energy plays a key role in the observed reactivity trends. The role of the aromaticity strength of these heteroarenes on the reactivity is also assessed.     

Synthesis of N-substituted carbazolones from α-iodo enaminones via Pd(0)-catalyzed intramolecular coupling under microwave irradiation

A variety of N-aryl and N-alkyl carbazolones were conveniently achieved in good to high yields via Pd₂(dba)₃-mediated intramolecular coupling of N-substituted α-iodo enaminones under microwave irradiation. The Pd(0)-catalyzed cyclization was found to proceed favorably with the more electron-deficient phenyl ring during the reactions involving unsymmetrical N,N-diaryl α-iodo enaminones. This unique property enables the construction of carbazolone skeleton containing nitro substituted benzenoid ring.     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of substituted 2,4,5,6-tetrahydrocyclopenta[c]pyrazoles and 2,4,5,6-tetrahydropyrrolo[3,4-c]pyrazoles by intramolecular nitrilimine cycloaddition

Both substituted 2,4,5,6-tetrahydrocyclopenta[c]pyrazoles and 2,4,5,6-tetrahydropyrrolo[3,4-c]pyrazoles have been synthesized by the 3+2 intramolecular dipolar cycloaddition of nitrilimines to alkynes. This cyclization has been extended to more versatile 3-bromo derivatives by the use of alkynylbromides as dipolarophiles.