间接原子吸收法测定苯并三氮唑

乙酸钠介质中 ,加入过量的铜 (Ⅱ )与苯并三氮唑生成沉淀 ,用火焰原子吸收法测定上清液中剩余的铜(Ⅱ ) ,工作曲线法测定了工业合成样品及内燃机冷却水中的苯并三氮唑。该方法测定苯并三氮唑线性范围为1 2mg/L～ 30mg/L ,回收率 (n =5)为 98.9～ 1 0 1 .0 %。文中还测定了难溶化合物的溶解度、溶度积和化合物的组成比。     

高效液相色谱法测定苯并三氮唑

提出了高效液相色谱法测定苯并三氮唑产品以及工业循环冷却水中苯并三氮唑含量的方法。色谱分离采用Kromasil C18(4.6 mm×250 mm,5μm)色谱柱,以乙腈-水(25+75)为流动相,流量为1.0 mL.min-1,检测波长为260 nm。苯并三氮唑的质量浓度在3.84~76.8 mg.L-1范围内与峰面积呈线性关系,平均回收率为96.4%。     

邻苯二甲酸在苯并三氮唑银为银源的光敏热显影体系中的作用

本文研究了邻苯二甲酸(H₂PA)的用量以及H₂PA的阴离子和阳离子对以苯并三氮唑银为银源的光敏热显影体系的影响.结果表明,在苯并三氮唑银体系中,邻苯二甲酸(H₂PA)的阳离子(H⁺)降低了体系的pH值,还原剂的显影活性和H₂PA与银离子的络合能力;而其阴离子(PA^2-)则与苯并三氮唑银生成中间体,起到传输银离子的作用.     

碲氢化钠与胺烷基化苯并三氮唑的反应

碲氢化钠是一个用途广泛的磁试剂,自作为有用的去溴试剂以来,日益受到化学工作者的关注,不断有文献报道它的合成及应用.例如能有效地还原卤代烃、硝基化合物、叠氮化合物和亚胺等.近年来,Katritzky报道了胺烷基化苯并三氮唑衍生物的合成及应用,此衍生物中的苯并三氮唑基是很好的离去基团,易被各种亲核试剂所取代.我们在前文中对硒氢化钠与胺烷基化苯并三氮唑反应生成二苄基二硒醚的合成进行了报道.本文用碲氢化钠与胺烷基化苯并三氮唑反应,结果生成还原产物N-取代胺.     

苯并三氮唑类化合物的合成及生物活性

设计并合成了6种新的苯并三氮唑类化合物,其结构均经^1H NMR和IR确认。初步测定了其生物活性．结果表明6种化合物对小白菜的胚根、根和苗的生长均具有一定的调节作用。     

含苯并三氮唑单元的聚对苯撑乙炔类聚合物的合成及性能

利用Pd（Ⅱ）配合物为催化剂,使用4,7-二溴-2-十二烷基-1,2,3-苯并三氮唑和1,4-二乙炔基-2,5-二（烷氧基）苯通过Sonogashira反应合成了3个带有不同长度烷氧基侧链,主链中含有1,2,3-苯并三氮唑单元的聚苯乙炔类聚合物。采用FT-IR、1H-NMR对其化学结构进行了表征。结果表明：这类聚合物的数均分子量在0.93×104～1.13×104,苯并三氮唑单元上长链烷基和苯环上长链烷氧基的存在使此类聚合物在CHCl3、THF等溶液中的溶解度较大,其固态薄膜也较容易制备,聚合物在固态薄膜状态下的紫外-可见最大吸收波长比在CHCl3溶液中红移了约45 nm,在固态薄膜状态下的荧光发射峰比在CHCl3溶液中也发生了较大的红移。     

苯并三氮唑及其羧酸酯衍生物对铜缓蚀机理的分子动力学模拟研究

用分子动力学(MD)方法, 模拟计算了5种铜缓蚀剂[苯并三氮唑(BTA)、苯并三氮唑-5-羧酸甲酯(MBTC)、苯并三氮唑-5-羧酸丁酯(BBTC)、苯并三氮唑-5-羧酸己酯(HBTC)、苯并三氮唑-5-羧酸辛酯(OBTC)]与Cu₂O晶体的相互作用. 结果发现, 中性条件下缓蚀剂分子与Cu₂O晶体的结合能均大于酸性条件下的数值, 但两种条件下结合能的大小排序均为OBTC＞HBTC＞BBTC＞MBTC＞BTA. 对体系各种相互作用以及对关联函数g(r)的分析表明, 体系结合能主要由库仑作用提供, Cu₂O晶体中的Cu原子与缓蚀剂分子中的N原子之间形成了配位键. 在与Cu₂O(001)晶面结合过程中, BTA及其衍生物分子发生了扭曲变形, 但形变能远小于体系的非键相互作用能.     

羧基功能化苯并三氮唑类离子液体的合成及在萃取-氧化脱硫中的应用

合成了新型离子液体(ILs)1-烷基-3-羧甲基苯并三氮唑双三氟甲磺酰亚胺盐,并对其进行了表征.将其与双氧水组成催化氧化体系,考察了脱除模型油品中硫化物的效果.结果表明,以离子液体1-5基-3-羧甲基苯并三氮唑双三氟甲磺酰亚胺盐[C2O2BBTA][NTf2]为萃取/催化剂,设定n(H2O2)∶n(S)=2.5∶1,m(模型油)∶m(离子液体)=5∶1,在75℃下反应1 h后,模型油中二苯并噻吩(DBT)、苯并噻吩(BT)和4,6-二甲基二苯并噻吩(4,6-DMDBT)的脱硫率分别为98.3%,98.3%和96.6%.所合成离子液体重复使用10次,脱硫率无明显变化.该方法操作简单、反应条件温和,可以实现深度脱硫.     

含1,2,3-三氮唑结构的1,5-苯并硫氮杂[艹卓]的合成及其抑真菌活性

设计合成了三类含1,2,3-三氮唑结构的1,5-苯并硫氮杂[艹卓]化合物3-(1H-1,2,3-三氮唑)-4-芳基-2,5-二氢-1,5-苯并硫氮杂[艹卓](5a^5f)、3-(2H-1,2,3-三氮唑)-4-芳基-2,3-二氢-1,5-苯并硫氮杂[艹卓](6a^6f)和3-(1H-1,2,3-三氮唑)-4-芳基-2,3,4,5-四氢-1,5-苯并硫氮杂[艹卓](7a^7f).研究了中间体及目标产物的合成条件,分离出其中两个副产物并进行了结构确定.目标产物的抑真菌活性测试表明,化合物5a^5f对真菌具有良好的抑制作用,对新生隐球菌的抑制效果尤为突出.初步抑真菌构效关系研究表明, 1H-1,2,3-三氮唑环和C=C双键是化合物5a^5f抑真菌活性的关键官能团.     

改进法合成1-苄基-3-烷基苯并三氮唑类离子液体及其表征

通过改进的方法合成了1-苄基-3-烷基苯并三氮唑类离子液体。 目标产物结构经FT-IR、1H NMR和13C NMR确证。 当烷基取代的苯并三氮唑、催化剂CuI和溴苄的物质的量比为10∶2.5∶11时,反应5~6 h收率可达82.7%~86.1%,探讨了离子液体溶解性及熔点与结构的关系。     

Corrosion inhibition of carbon steel immersed in a 1 M HCl solution using benzothiazole derivatives

Corrosion inhibition effect of 2-mercaptobenzothiazole (MBT) and 2-aminobenzothiazole (ABT) compounds on ST-37 carbon steel in 1 M hydrochloric acid solution was investigated by electrochemical impedance spectroscopy (EIS), and it was observed that both of these compounds have corrosion inhibition effect on carbon steel. Evaluation of electrochemical behavior in test solutions showed that by increasing the immersion time from 15 to 300 min, corrosion resistance of samples is increased and at the same immersion time MBT has a better corrosion inhibition in comparison to ABT. AFM technique was performed for MBT and ABT. The results of calculations showed superior inhibition efficiency of MBT in comparison to ABT. This can cause easier protonation and consequently adsorption on the metal surface occurs.     

Crystal Structures of 2-Aminobenzothiazole-based Inhibitors in Complexes with Urokinase-type Plasminogen Activator

Urokinase-type plasminogen activator （uPA） plays a crucial role in the regulation of plasminogen activation, tumor cell adhesion and migration. The inhibition of uPA activity is a promising mechanism for anti-cancer therapy. Most current uPA inhibitors employ a highly basic group （either amidine or guanidine group） to target the S1 pocket of uPA active site, which leads to poor oral bioavailability. Here we study the possibility of using less basic 2-aminobenzothiazole （ABT） as S1 pocket binding group. We report the crystal structures of uPA complexes with ABT or 2-amino-benzothiazole-6-carboxylic acid ethyl ester （ABTCE）. The inhibitory constants of these two inhibitors were measured by a chromogenic competitive assay, and it was found that ABTCE is a better inhibitor for uPA （Ki = 656 μM） than ABT （Ki = 5.03 mM）. This work shows that 2-amniobenzothiazole can be used as P1 group which may have better oral bioavailability than the commonly used amidine or guanidine group. We also found the ethyl ester group occupies the characteristic oxyanion hole and contacts to uPA 37- and 60-loops. Such work provides structural information for further improvements of potency and selectivity of this new class of uPA inhibitor.     

2‐Aminobenzenethiol‐Functionalized Silver‐Decorated Nanoporous Silicon Photoelectrodes for Selective CO2 Reduction

A molecularly thin layer of 2‐aminobenzenethiol (2‐ABT) was adsorbed onto nanoporous p‐type silicon (b‐Si) photocathodes decorated with Ag nanoparticles (Ag NPs). The addition of 2‐ABT alters the balance of the CO₂ reduction and hydrogen evolution reactions, resulting in more selective and efficient reduction of CO₂ to CO. The 2‐ABT adsorbate layer was characterized by Fourier transform infrared (FTIR) spectroscopy and modeled by density functional theory calculations. Ex situ X‐ray photoelectron spectroscopy (XPS) of the 2‐ABT modified electrodes suggests that surface Ag atoms are in the +1 oxidation state and coordinated to 2‐ABT via Ag?S bonds. Under visible light illumination, the onset potential for CO₂ reduction was ?50 mV vs. RHE, an anodic shift of about 150 mV relative to a sample without 2‐ABT. The adsorption of 2‐ABT lowers the overpotentials for both CO₂ reduction and hydrogen evolution. A comparison of electrodes functionalized with different aromatic thiols and amines suggests that the primary role of the thiol group in 2‐ABT is to anchor the NH₂ group near the Ag surface, where it serves to bind CO₂ and also to assist in proton transfer.     

Complexes of Eu(III), Tb(III) and Cu(II) with proton transfer compound between 2,6-pyridinedicarboxylic acid and 2-aminobenzothiazole: characterization of the structures and physical properties

A proton transfer compound, (ABTH)⁺(PydcH)^? (1), obtained from 2-aminobenzothiazole (ABT) and 2,6-pyridinedicarboxylic acid (Pydc) as well as its Eu(III), Tb(III), and Cu(II) complexes (ABT)₃[Eu(Pydc)₃]·5H₂O (2), (ABT)₃[Tb(Pydc)₃]·5H₂O (3), and (ABT)[Cu(Pydc)(PydcH)]·3H₂O (4) were obtained under ambient conditions and structurally verified by single-crystal X-ray diffraction analyses and further characterized by elemental analyses, powder X-ray diffraction (PXRD), infrared spectroscopy (IR), thermogravimetric analysis (TGA), and magnetic measurements. Compounds 2–4 are the first known solids containing complex anions with Pydc ligands, 2-aminobenzothiazole cations (ABT), and solvate water molecules. During the synthesis of 3, a secondary phase with the formula ABTCl?H₂O was obtained and characterized by elemental analysis and single-crystal X-ray diffraction. The asymmetric unit of 5 consists of six symmetry independent ABT cations, six chlorides, and six water molecules. The two lanthanide complexes showed characteristic emissions of Eu³⁺ and Tb³⁺ ions. The good solubilities of these complexes in water and their luminescence properties make them attractive luminescent labels of biological molecules.     

Determination of 2-substituted benzothiazoles of industrial use from water by liquid chromatography/electrospray ionization tandem mass spectrometry

A method was developed for the analysis of 2-substituted benzothiazoles from wastewaters by reversed-phase liquid chromatography/electrospray ionization tandem mass spectrometry (LC/ESI-MS/MS). While benzothiazole (BT), 2-amino- (ABT), 2-methyl-, 2-thiocyanomethylthio- and 2-methylthiobenzothiazole were separated with a methanol gradient acidified with formic acid and detected in the positive mode, 2-mercapto- and 2-hydroxybenzothiazole (OHBT) as well as benzothiazole-2-sulfonic acid (BTSA) were separated with the addition of ammonium acetate and detected in the negative ion mode. Detection limits range from 10 ng L(-1) for ABT to 200 ng L(-1) for OHBT after direct injection of 100 μL sample volumes, while BT requires 2.5 μg L(-1). The method is, thus, suitable for direct analysis in wastewaters. Its application to tannery effluent samples revealed, that, besides a 90-95% elimination of total benzothiazoles, the concentration of OHBT and BTSA increased during the biological treatment. Copyright 2000 John Wiley & Sons, Ltd.     

Diazocoupling reaction for the spectrophotometric determination of physiologically active catecholamines in bulk and pharmaceutical preparations

A simple and sensitive spectrophotometric method for the determination of four catecholamines viz., adrenaline bitartarate (ABT), methyldopa (MDP), dopamine hydrochloride (DPH), and levodopa (LDP), in both pure form and in pharmaceutical formulations is described. The method is based on the reaction of diazotized sulphanillic acid (DSA) with catecholamines in a basic medium to yield orange-red colored products having absorption maxima at 507 nm for MDP and at 475 nm for others analytes. The colored species obeyed Beer’s law in the range of 1–27, 0.5–17, 0.6–15, and 1.5–19.2 μg/mL for ABT, MDP, DPH, and LDP, respectively. The molar absorptivity values as obtained from Beer’s law data were found to be 0.812 × 10⁴, 0.947 × 10⁴, 0.927 × 10⁴, and 0.709 × 10⁴ L/(mol cm), while Sandell’s sensitivity values were observed to be 412.03, 25.15, 20.44, and 27.81 ng/cm² for ABT, MDP, DPH, and LDP, respectively. Common excipients did not interfere with the proposed method. The results of the proposed methods compare favorably with those of official methods. The proposed method offers a simplicity, reliability, rapidity, and accuracy compared to the existing methods. The text was submitted by the author in English.     

Synthesis,structure, photochromic,and fluorescent imaging properties of sodium-3,3′-azobis(1,2,4-triazole)

A crystal of [Na₂(ABT)?·?5H₂O] (ABT?=?3,3′-azobis(1,2,4-triazole)) (1) was characterized by single-crystal X-ray diffraction. Complex 1 features a 1-D chain and each ABT^2? is a µ_1,2,6 bridge with three triazole nitrogen atoms coordinating to three different sodium(I). Aqueous solution of 1 (6.0?×?10^?5?mol?L^?1) shows photochromism. Fluorescence of solid 1 displays green photoluminescence under UV-light or laser irradiation and can be employed to label onion cell.     

Preferential adsorption of fetal bovine serum on bare and aromatic thiol-functionalized gold surfaces in cell culture media

Intracellular uptake of serum-coated gold nanoparticles (AuNPs) in a single mammalian cell was examined in order to investigate the interactions of cell culture media and aromatic thiol-functionalized gold surfaces using micro-spectroscopic tools. The AuNPs modified by the aromatic thiols of para-aminobenzenethiol (ABT), para-hydroxy benzenethiol (HBT), and para-carboxylic benzenethiol (CBT, para-mercaptobenzoic acid) bearing NH(2), OH, and COOH surface functional groups are presumed to adsorb the serum proteins as indicated from the compiled quartz crystal microbalance (QCM) data. The QCM results indicate that among the constituents, fetal bovine serum (FBS) should be the major adsorbate species on AuNPs incubated in Roswell Park Memorial Institute (RPMI) medium. The functionalized AuNPs were found to be internalized as an aggregation state in mammalian cells as evidenced by transmission electron microscopy (TEM) images. We monitored such cellular uptake behaviors of aromatic thiol-modified AuNPs using dark-field microscopy (DFM)-guided confocal surface-enhanced Raman scattering techniques in order to identify the three-dimensional localization inside the single cell. We found that the uptake amounts of ABT, HBT, and CBT were similar by counting up to 70 particles inside the cells incubated in the solution mixture of the aromatic thiol and 1,4-phenylenediisocyanide (PDIC) as a reference. This result indicates for the short aromatic thiol compounds, the AuNPs should enter the cell after the serum-coating regardless of the surface functional groups. Considering that the aromatic thiols have little effect on the serum coating, the DFM/SERS method is an effective tool for monitoring the localization of AuNPs inside a single cell.     

Coordination modes of 1-allyl benzotriazole: synthesis and characterization of cobalt(II), nickel(II), copper(II), copper(I) and silver(I) complexes

Summary The synthesis and coordination behaviour of 1-allylbenzotriazole (ABT), containing both -donating heterocyclic ring nitrogen(s) and a -bonding olefinic group, has been studied by complexation with Co^II, Ni^II, Cu^II, Cu^I and Ag^I salts. The solid complexes M(ABT)₂X₂ (M=Co, Ni or Cu and X=a counterion) and M(ABT)X (M=Cu or Ag and X=Br, I, or NO₃) have been characterised by¹H-n.m.r. (representative Cu^I species) and other physical data. Different modes coordination for the title ligand have been proposed based upon i.r. data which indicate the participation of a -donating ring nitrogen only in complexes with bivalent metal salts, and the involvement of both the ring nitrogen and the allylic olefinic component in bonding to a monovalent metal ion.¹H-n.m.r. data are qualitatively commensurate with participation of the allyl group in monovalent metal complexes.     

Electrochemical and Quantum Chemical Studies of Azoles as Corrosion Inhibitors for Mild Steel in Hydrochloric Acid

The inhibition effect of three azole compounds, 2-aminobenzimidazole(ABM), 2-aminothiazole(AT) and 2-aminobenzothiazole(ABT), on the corrosion of mild steel in a 1 mol/L HCl solution was investigated by means of potentiodynamic polarization measurement, electrochemical impedance spectroscopy(EIS) and scanning electron mi-croscopy(SEM). The correlation between inhibition efficiency and molecular structure of inhibitor was theoretically studied via quantum chemical calculations. The results show that the inhibition efficiency(η) of the inhibitors follows the order of η_ABT >η_AT >η_ABM. Moreover, ABM, AT and ABT belong to mixed-type inhibitors. The adsorption of the inhibitors on the steel surface follows the Langmuir adsorption isotherm, with both physisorption and chemisorption.