WQD-1沸石离子交换性能的研究

测定了W_QD-1沸石在一价碱金属离子混合溶液中的分配系数、饱和交换量和在25℃时，NH⁺₄/K⁺、NH⁺₄/Na⁺交换等温线。得出该沸石一价离子选择性序列为：Cs⁺>Rb⁺>K⁺>Na⁺>Li⁺, Na⁺/K⁺交换自由焓变ΔG(T,P)=-6.745 KJ/mol。     

K+掺杂双钙钛矿Cs2AgInCl6的发光性质

采用固相球磨法制备了K⁺掺杂双钙钛矿Cs₂AgInCl₆纳米材料,该方法无需配体辅助,绿色环保。通过X射线衍射和拉曼光谱对晶体结构进行研究,通过激发光谱、发射光谱和时间分辨光谱对其发光性能进行研究。结果表明,Cs₂AgInCl₆为立方晶体,属于Fm3m空间群,由于宇称禁戒跃迁,其荧光量子产率(PLQY)低,小于0.1%。低于60%的K⁺掺杂主要取代Ag⁺的位置,引起Cs₂AgInCl₆的晶格膨胀,消除了晶格结构的反演对称性,打破了宇称禁戒跃迁,掺杂后Cs₂AgInCl₆的光致发光强度显著增强。K⁺的最佳掺杂比例为40%,Cs₂Ag_0.6K_0.4InCl₆材料发射中心波长为640 nm,半高宽为180 nm,平均荧光寿命达到29.2 ns,PLQY达到10.5%。当K⁺掺杂比例超过60%,K⁺开始取代Cs⁺的位置,产物发生相变,出现立方相的Cs_2-xK_1+x-yAg_yInCl₆和单斜相的Cs_2-xK_1+xInCl₆产物,这些产物由于强电子-声子耦合,非辐射复合占据主导地位。     

双阳离子体系高通量丝光沸石膜的合成及其乙酸脱水应用（英文）

采用多种表征技术详细研究了碱金属阳离子对丝光沸石分子筛膜生长和渗透汽化性能的影响。结果表明,Li~+、Na~+、K~+和Cs~+以及Na~+-Li~+、Na~+-K~+和Na~+-Cs~+的不同离子组合对丝光沸石分子筛膜的形貌和性能有很大影响。研究发现,碱金属阳离子通过促进硅在初始凝胶中的溶解,在硅铝酸盐的重排过程中起到结构导向作用,进而起到构筑丝光沸石晶体骨架结构的作用。Na~+对丝光沸石晶体的结晶有明显的促进作用,而Li~+、K~+和Cs~+在相同的结晶时间内表现出较慢的结晶速率。在合成凝胶中用K~+代替少量Na~+可以显著改善膜表面的亲水性。特别是合成凝胶中Na~+/K~+比(n_(Na~+)/n_(K~+))为2时,形成了更致密、更亲水的丝光沸石分子筛膜,显示出更高的渗透汽化性能。对于90℃下HAc质量分数为90%的HAc/H_2O混合物的分离,该膜显示出2.67 kg·m~(-2)·h~(-1)的高渗透通量和约为4 000的分离因子。此外,最优条件下合成的丝光沸石分子筛膜在90℃下长达240 h渗透汽化分离90%的HAc/H_2O混合物依然显示优越的酸稳定性。     

γ-AlOOH/Al2O3修饰硅藻土的制备与Cs+、Pb2+吸附性能

以结晶氯化铝(AlCl₃·6H₂O)作为铝源,十二烷基苯磺酸钠(SDBS)为模板剂,采用水热法在硅藻土盘上制备了束状纳米结构γ-AlOOH/Al₂O₃复合吸附剂。采用XRD、SEM、TEM、TG/DSC、N₂吸脱附等对样品进行了表征。研究了样品对¹³³Cs⁺及Pb²⁺的吸附能力。研究表明,样品γ-AlOOH/硅藻土、γ-Al₂O₃/硅藻土对Cs⁺及Pb²⁺均具有良好的吸附性能,两者对Cs⁺的去除率分别为98.9%和99.6%;对Pb²⁺的最大吸附量分别为357.1、416.7mg·g^-1。两种样品对Pb²⁺的吸附均符合Langmuir吸附模型。     

ZnAl2O4:Mn材料的制备及发光性能

以共沉淀法与煅烧法联用,成功制备了一系列ZnAl₂O₄:xMn样品。通过扫描电镜和X射线粉末衍射测试研究了样品的形貌和物相特征,结果表明尖晶石结构的ZnAl₂O₄中[AlO₆]的八面体位可以有效被Mn⁴⁺替代。通过荧光激发和发射光谱研究了样品的发光性能,发现Mn⁴⁺在ZnAl₂O₄体系中掺杂可以显示出明亮的红色发光(发射峰值位于680 nm处)。比较不同Mn⁴⁺浓度(Mn与Al的物质的量之比)掺杂样品的发光强度时发现,Mn⁴⁺最佳掺杂浓度为0.06%。通过德克斯特公式分析了发光强度与浓度关系,探究浓度猝灭机制,结果表明最邻近离子之间能量传递造成Mn⁴⁺浓度猝灭的发生。为了提高Mn⁴⁺的发光强度,选择了7种金属离子(Li⁺、Na⁺、K⁺、Ca²⁺、Sr²⁺、Sn²⁺和Ga³⁺)与Mn⁴⁺共掺杂进入ZnAl₂O₄基质中,其中效果较突出的为Li⁺和Ga³⁺,其共掺杂使Mn⁴⁺发光强度分别增强0.6倍和1倍。     

间歇式水热合成制备丝光沸石膜及其异丙醇脱水应用

采用市售廉价大孔α-Al₂O₃管作为基质材料，通过热浸渍法在管外表面涂敷晶种，随后在无模板剂体系下，利用新型的间歇式水热合成法制备丝光沸石膜。对比了传统加热和间歇式加热对丝光沸石膜形貌、结构及渗透蒸发异丙醇脱水分离性能的差异。考察了合成液中Na₂O/SiO₂、SiO₂/Al₂O₃和NaF/SiO₂物质的量之比在间歇式水热合成下对丝光沸石膜的影响。研究结果表明，当合成液中Na₂O/SiO₂、SiO₂/Al₂O₃和NaF/SiO₂物质的量之比分别为0.24、16.7和0.25时，制备的丝光沸石膜渗透蒸发异丙醇脱水分离性能最佳，在75℃下，对异丙醇/水(9∶1，w/w)的渗透通量达5.60 kg·m^-2·h^-1，水对异丙醇的分离因数大于10 000。     

钌(Ⅱ)配合物[Ru(dpq)2L]4+的合成、晶体结构及与G-四链体DNA的相互作用

以cis-[Ru(dpq)₂Cl₂]·2H₂O(dpq=二吡啶[3,2-d:2',3'-f]二氮萘)为原料与5,5'-二(1-(三乙胺)甲基)-2,2'-联吡啶阳离子(L)合成钌(Ⅱ)配合物[Ru(dpq)₂L](PF₆)₄,并研究了该配合物与G-四链体DNA的作用:FRET实验表明,配合物对人端粒DNAh-telo具有选择性,其作用能力要强于同癌基因启动子区域的四链DNA,如c-myc和bcl2;CD光谱表明,在Na⁺和K⁺都不存在的情况下,配合物能诱导h-telo形成平行结构;此外,紫外和发射光谱都显示,配合物在K⁺溶液中与h-telo的作用力要大于在Na⁺溶液中的。     

溶胶-凝胶法合成Li1-xNaxMn2O4及其作为水系锂离子电池正极材料的电化学性能

用溶胶凝胶法合成了Na⁺离子掺杂的Li_1-xNa_xMn₂O₄(x=0,0.01,0.03,0.05)。X射线衍射图表明Na⁺取代Li⁺进入Li_1-xNa_x Mn₂O₄晶格中,扫描电镜图看出产物是粒径为100~300 nm的颗粒。恒流充放电测试结果表明,Li_0.97Na_0.03Mn₂O₄在2C倍率下循环100圈后放电容量保持率比未掺杂的LiMn₂O₄从51.2%提升到84.1%。循环伏安测试表明Na⁺离子掺杂降低了材料极化且增大了锂离子扩散系数。10C倍率下Li_0.97Na_0.03Mn₂O₄仍有79.0 mAh·g^-1的放电容量,高于未掺杂样品的52.1 mAh·g^-1。Na⁺离子掺杂可以稳定材料结构并提高锂离子扩散系数,从而提高LiMn₂O₄的电化学性能,是一种可行的改性方法。     

电荷补偿对Ba2ZnGe2O7：Bi3+荧光粉发光性质的影响

采用高温固相法制备了2个系列的荧光粉样品：Ba_2-xZnGe₂O₇：xBi³⁺（系列Ⅰ）和Ba_1.994-yK_yZnGe₂O₇：0.006Bi³⁺（系列Ⅱ）。X射线衍射（XRD）测试结果表明,少量Bi³⁺、K⁺的掺杂不会明显改变材料的物相结构。样品的荧光光谱测试结果表明,虽然2个系列样品的发光光谱都随组成成分变化有少量变化,但发光颜色基本上均为黄绿色。在358 nm的激发下,荧光粉的发射光谱呈现一个峰值在500 nm的宽发射带,归属于³P₁→¹S₀能级跃迁。在500 nm监测下,荧光粉的最强激发峰位于358 nm,归属于¹S₀→³P₁能级跃迁,此外还有一个位于320 nm的肩峰归属于O^2--Bi³⁺电荷转移带。系列Ⅰ样品的光谱数据结果指出,Bi³⁺的最佳掺杂量x为0.006。在该基质中,Bi³⁺掺杂取代Ba²⁺属于不等价取代,会在晶格中产生Ba²⁺空位或间隙O^2-,对材料的发光强度产生负面影响。对此,采用K⁺与Bi³⁺协同掺杂起到电荷补偿的作用,填补Ba²⁺空位或捕获间隙O^2-缺陷。空位被填补或间隙被捕获均减少了晶格畸变,从而使发光强度明显提高。系列Ⅱ样品的光谱数据表明,完全电荷补偿的荧光粉样品相比于没有掺K⁺的样品,其发光强度提高了约2.5倍。     

MFI纳米片沉积层气相转化制备超薄b轴取向沸石膜

利用乙二胺-水蒸汽进行气相转化(VPT)制备超薄、取向MFI沸石膜,通过将MFI纳米片沉积层转化为致密的沸石膜,实现了膜厚度的有效控制。扫描电子显微镜和X射线衍射表明,制备的沸石膜膜厚度约为280 nm,具有高度b轴取向的致密结构。丁烷异构体双组分分离测试结果表明,在333 K下,等物质的量的正丁烷/异丁烷混合物的正丁烷渗透速率和分离因子分别为1.5×10^-7 mol·m^-2·s^-1·Pa^-1和14.8。Na₂SiO₃作为低聚硅源在MFI沸石纳米片二次生长过程中能够提供硅源和碱度,通过在胺类蒸汽中实现MFI沸石纳米片间的融合生长,进一步提高了膜的取向度和致密性。     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.     

Mechanism of action of base-catalyzed oxygenation of phenol derivatives

Cyclopropyl derivative of 2,6-di-tert-butylphenol is synthesized as a probe to investigate the mechanism of base-catalyzed autooxidation of phenol derivatives. Our study indicates that one electron reduction of molecular oxygen from phenolate gives phenoxyl radical 3, a key intermediate of autooxidation. The coupling of phenoxyl radical and superoxide radical gives peroxylate anion 4 and produces the final epoxy alcohol adduct 6.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

化学计量中不确定度评定研究进展

测量不确定度是表征合理地赋予被测量之值的分散性的参数。本文针对化学计量不确定度评定基础模型仅适用于线性模型、概率分布为正态分布或缩放位移t分布等局限,介绍了近年来不确定度评定的研究热点:蒙特卡罗方法(Monte Carlo Method,MCM),不确定度评定的来源、评定概念、评估方法及其发展过程,扩大了测量不确定度评定与表示的适用范围。     

微量钙的测定方法研究进展

介绍了1995-2006年期间测定微量和痕量钙的方法,如电感耦合等离子体-原子发射光谱法、原子吸收光谱法以及离子色谱法等的工作原理和特点,并说明了其测定微量钙的应用领域。并对微量钙的测定技术进行了展望(引用文献55篇)。     

Stages of thermal decomposition of sodium oxo-salts of sulphur

Thermal behaviour of sodium oxo-salts of sulphur: Na₂SO₄, Na₂S₂O₇, Na₂S₂O₆, Na₂SO₃, Na₂S₂O₅, Na₂S₂O₄, Na₂S₂O₃, Na₂S₃O₆ and of sulphides Na₂S and Na₂S₂ was studied on heating up to 1000°C. The experiments were performed with anhydrous compounds obtained from commercial products by recrystallisation and dehydration. The stage mechanisms of decomposition of anionic sub-lattices of the salts have been proposed basing on the Górski’s morphological classification of simple species. The thermal stability and the stage decomposition mechanisms were correlated with the structure and the potential chemical properties of the salt anions. The thermal decomposition processes were studied by means of thermal analysis, and the decomposition products were identified by means of X-ray phase analysis.