F-T组分改性KCuZrO2催化剂上CO加氢合成异丁醇的性能研究

采用共沉淀法分别制备了不同F-T组分(Fe、Co、Ni)改性的KCuZrO_2催化剂,并用于催化CO加氢合成异丁醇。通过BET、XRD、TEM、XPS、H_2-TPR、CO-TPD以及in-situ DRIFTS对催化剂进行了表征。结果显示,F-T组分的加入促进了乙醇和丙醇的形成,但是对异丁醇选择性影响不同。结果表明,Fe促进了催化剂中各组分的分散,活性组分Cu在催化剂表面发生了富集,提高了H_2/CO活化吸附;另外,KFeCuZrO_2的催化剂表面含有较多的C1物种,有利于乙醇和丙醇进一步发生β-加成反应得到异丁醇,而Co和Ni改性的催化剂上缺少足够的C1物种,因此,异丁醇的选择性并未明显增加。Co的引入对催化剂结构以及Cu的分散影响不大,但是Co改性后催化剂性能有所下降,其原因是催化剂发生了失活; Ni添加后催化剂比表面积有所减小,且催化剂表面Cu/Zr物质的量比也降低到0. 19,催化剂粒径增大,Cu-Zr之间相互作用减弱,异丁醇选择性降低。     

结构助剂SiO2、Al2O3对铁基催化剂浆态床F-T合成性能的影响

采用连续共沉淀与喷雾干燥成型技术相结合的方法制备了微球状Fe/Cu/K/SiO2和Fe/Cu/K/Al2O3催化剂，研究SiO2和Al2O3作为结构助剂对铁基催化剂吸附行为、炭化行为及F-T合成反应性能的影响。表征结果表明,与Al2O3相比较，SiO2抑制了H2的吸附，但促进了CO的吸附，有利于催化剂的炭化。催化剂在260℃、1.5MPa、H2/CO=0.67和2000h-1下的浆态床F-T合成反应评价表明，Fe/Cu/K/SiO2催化剂具有较高的F-T合成活性、高的水煤气变换反应（WGS）活性，且其烃产物选择性明显向高炭数方向偏移，而Fe/Cu/K/Al2O3催化剂则表现出较低的F-T合成活性、低的水煤气变换反应（WGS）活性和高的轻质烃选择性。但Fe/Cu/K/Al2O3催化剂比Fe/Cu/K/SiO2催化剂具有更好的运行稳定性。     

Cu/Fe催化剂催化甲醇部分氧化制氢

采用共沉淀法制备的Cu/Fe催化剂催化甲醇部分氧化制氢结果表明，Fe的引入，有利于降低CO选择性，Cu/Fe比对催化性能有明显影响，当Cu/Fe比为2：8时，甲醇转化率最高，与其它的Cu基催化剂相比，在较宽的Cu/Fe比范围内，CO的选择性均保持在较低的水平，利用XRD，XPS等方法，对Cu/Fe催化剂进行表征，结果表明，Fe的引入，有利于活性组分Cu在催化剂表面上的分散，在反应过程中Cu组分向表面富集，因而可使得催化剂表面的Cu物种不因Fe的引入而减少。     

Fe、Co组成对Cu-Fe-Co基混合醇催化剂合成性能的影响

采用共浸渍法制备了一系列不同Fe、Co组成的Cu-Fe-Co基混合醇催化剂,对其CO加氢合成混合醇反应性能进行了考察,并采用BET比表面积分析、X射线衍射（XRD）、X射线光电子能谱（XPS）、场发射扫描电子显微镜（FE-SEM）及H₂程序升温还原（H₂-TPR）等手段对其进行了表征.结果表明:Cu-Fe二元催化剂添加适量的Co可以明显提高催化剂醇的明空收率（STY）、CO转化率,而总醇选择性不变.当活性组分Cu、Fe及助剂Co的质量分数分别为25%、22%、3%时,催化剂醇的时空收率高达205.6 g·kg^-1·h^-1,CO转化率为56.6%.XRD、XPS和TPR结果表明:在Cu组分含量不变时,少量Co组分的引入使催化剂表面形成微量的CuFe₂O₄相,促进了Cu-Fe组分间相互作用的增强,改善了催化剂活性组分的分散度,有利于提高催化剂活性及醇的时空收率;随Co含量的增大,催化剂中金属组分间的相互作用发生转变,形成了Cu-Co尖晶石相,导致催化剂的醇选择性有所下降.     

SnO_2-SiO_2负载Cu、Ni催化剂的CO_2加氢反应性能

采用表面反应改性法制备了SnO2 SiO2 (SnSiO)表面复合物载体 ,用等体积浸渍法制备了SnSiO担载的Cu Ni双金属催化剂。借助BET、XRD、TPR、IR和微反等技术研究了SnSiO及其负载的Ni、Cu双金属催化剂的表面构造、化学吸附及CO2 加氢反应性能。结果表明 :SnSiO是SnO2 单分子层价联于SiO2 表面的复合氧化物 ,仍保持类似SiO2载体的孔结构和比表面 ;SnO2 引入SiO2 表面后可以有效地促进CuO、NiO的还原 ,还原后成为负载在SnSiO载体表面的Cu Ni合金 ;CO2 在负载型Cu Ni合金表面Cu或表面Ni位上发生化学吸附 ,形成线式和剪式吸附态 ;CO2 在催化剂上的加氢反应产物主要是CH3 OH、CH4 、CO和H2 O ,生成CH3 OH的选择性与催化剂组成及反应条件密切相关。Cu Ni催化剂 ,在 0 5MPa ,170℃ ,H2 /CO2 (mol/mol)为 3的条件下 ,CH3 OH的选择性达到 84 6 %。     

溶剂化金属原子浸渍法制备高分散载型催化剂 II. Fe,Co,Ni催化剂的分散度和催化性能研究

本文利用一种新的方法-溶剂化金属原子浸渍法制备了Fe/γ-Al_2O_3, Fe/SiO_2, Co/γ-Al_2O_3,Co/SiO_2, Ni/γ-Al_2O_3和Ni/SiO_2六种催化剂。H_2化学吸附, TEM和XRD测定结果表明这些催化剂中Fe, Co, Ni金属颗粒平均直径都小于3.0 nm, 金属分散度均大于50%。作者研究了Fe/γ-Al_2O_3, Co/γ-Al_2O_3和Ni/γ-Al_2O_3三种催化剂在CO+H_2反应中的催化行为, 测定了碳氢产物分布和比催化活性, 表明随着H_2/CO比增大和反应温度升高。较高分子量物种产量减少, 有利于生成甲烷。催化剂的活性大小次序为Fe>Ni>Co。     

溶剂化金属原子浸渍法制备高分散负载型催化剂——Ⅱ,Fe,Co,Ni催化剂的分散度和催化性能研究

本文利用一种新的方法-溶剂化金属原子浸渍法制备了Fe/γ-Al_2O_3,Fe/SiO_2,Co/γ-Al_2O_3,Co/SiO_2,Ni/γ-Al_2O_3和Ni/SiO_2六种催化剂。H_2化学吸附,TEM和XRD测定结果表明这些催化剂中Fe,Co,Ni金属颗粒平均直径都小于30A,金属分散度均大于50%。作者研究了Fe/γ-Al_2O_3,Co/γ-Al_2O_3和Ni/γ-Al_2O_3三种催化剂在CO+H_2反应中的催化行为,测定了碳氢产物分布和比催化活性,表明随着H_2/CO比增大和反应温度升高。较高分子量物种产量减少,有利于生成甲烷。催化剂的活性大小次序为Fe>Ni>Co。     

过渡金属对分子筛担载Pd催化剂上CO氧化性能影响

分别采用共浸和连续浸渍法制备了一系列添加过渡金属的Pd-M-Ox-NaZSM-5(M=Cr，Mn，Fe，Co，Ni，Cu，Zn，Mo，Zr等)负载型催化剂．以CO氧化为探针反应，考察了不同制备方法对CO氧化性能影响，结果表明共浸法制备的各催化剂其活性明显优于连续浸渍法．详细考察了反应温度、Fe含量、氢气预还原、空速以及水蒸气等对共浸Pd-Fe-Ox-NaZSM-5催化剂上CO氧化行为影响，并应用XRD和XPS等手段对催化剂体相结构和表面状态进行了表征．结果表明：加入Fe2O3可明显提高Pd/NaZSM-5催化剂活性，且催化CO氧化的转化率随反应温度及Fe含量增加而增加；空速增加以及H2预还原作用导致Pd-Fe-Ox-NaZSM-5活性有所降低；催化剂对水蒸气较为敏感．XRD测试结果表明催化剂中Pd组分处于较高分散状态，以红铁矿形式存在的Fe2O3的引入，促进了Pd物种在NaZSM-5载体上的分散．表面XPS分析证实Fe2O3与Pd物种间存在较强的相互协同作用，且催化剂表面Pd物种处于较高氧化状态．Pd的高分散及其与Fe2O3的相互协同作用是共浸催化剂具有高活性的关键因素．     

Cu/Ni负载型Beta分子筛催化剂的乙醇水蒸气重整制氢催化性能研究

采用等体积浸渍的方式,在全硅Beta分子筛载体上担载Cu、Ni活性组分,制备出一系列xCuyNi-ABZ多功能乙醇水蒸气重整制氢催化剂。通过XRD、TEM、SEM-EDX以及XPS等多种表征手段,研究催化剂的结构特性、活性组分含量等因素对催化性能的影响,依据反应产物分布,揭示其作用机理。结果表明,以Beta分子筛为载体可促使活性组分以纳米颗粒的形式高度分散于载体表面,并且存在较强的载体-金属作用力。与传统SiO_2为载体催化剂相比,2.5Cu2.5Ni-ABZ催化剂具备良好的乙醇水蒸气重整催化性能,当反应温度为450℃,实现100%的乙醇转化率和67.23%的H_2选择性,且副产物CO(4.14%)、CH_4(5.65%)含量相对较低。这可归因于Cu和Ni活性组分间的高效协同作用,Cu具有良好的乙醇脱氢性能,生成反应中间体乙醛;在反应过程中,乙醛的重整和分解是两个受温度影响的竞争反应,Ni组分利用其较强的C-C键断裂能力,随温度的升高,乙醛重整反应占主导作用,生成目标产物H_2。通过对反应后样品分析表明,2.5Cu2.5Ni-ABZ催化剂具备良好的抗烧结和抗积炭催化性能。     

双配体CuFe@MOFs材料为前驱体的催化剂的组分调控对CO2加氢制C2+醇性能的影响

采用水热法制备了以对苯二甲酸和对氨基苯甲酸为配体的双配体Fe基MOFs材料(MIL-88B(Fe)),在浸渍一定量Cu物种后经氮气气氛焙烧得到活性组分均匀分散的CuFe基催化剂。通过改变2种配体的比例调控催化剂表面Fe活性物种的价态分布,并考察了其用于固定床反应器上CO_2加氢制C_(2+)醇的催化性能,结合X射线衍射(XRD)、H_2程序升温还原(H2-TPR)、N_2吸附-脱附、扫描电子显微镜(SEM)、X射线光电子能谱(XPS)等表征结果发现,对苯二甲酸与对氨基苯甲酸物质的量之比为5∶2时,催化剂表面低价态铁原子占比为71.27%,催化剂展现最优的催化活性,CO_2转化率为8.80%,总醇选择性为31.52%,其中C_(2+)醇的物质的量分数达到94.70%。     

Ga_2O_3改性Cu/SiO_2催化剂降低水蒸气催化重整产物中CO选择性

采用蒸氨法制备的xGa-Cu/SiO_2催化剂可以同时产生Cu~0和Cu~+物种,加入Ga后催化剂的二甲醚水蒸气重整反应活性和选择性都有很大程度的提高,其中5Ga-Cu/SiO_2催化剂在380°C时的二甲醚转化率为99.8%,CO选择性为4.8%。通过透射电子显微镜(TEM),氢气-程序升温还原(H_2-TPR),N_2O滴定和X射线光电子能谱(XPS)结果发现,Ga与Cu物种之间的相互作用,一方面可以提高Cu物种的分散度,另一方面可以促进Cu~+的形成。通过改变Ga负载量可以调变Cu~+/(Cu~0+Cu~+)的比例,氢气的时空收率结果表明,Ga通过调变Cu~+/(Cu~0+Cu~+)影响催化活性,并且当Cu~+/(Cu~0+Cu~+)=0.5时,氢气时空收率达到最大值为5.02mol·g~(-1)·h~(-1)。程序升温表面反应(TPSR)结果表明,Ga通过促进水气变换反应提高反应产物CO_2选择性。     

CaO对Cu-ZnO-ZrO_2催化CO_2加H_2合成甲醇性能影响

用CaO作为改性助剂,采用并流共沉淀法制备了CuO∶ZnO∶ZrO_2为5∶4∶1(物质的量比),CaO添加量为0、1%、2%、4%、8%、16%(摩尔分数)的六组催化剂。用X射线衍射(XRD)、微商热重(TG-DTG)、傅里叶红外(FT-IR)、N2吸附脱附(BET)、X射线光电子能谱(XPS)、氢气程序升温还原(H_2-TPR)、CO_2程序升温脱附(CO_2-TPD)、NH_3程序升温脱附(NH_3-TPD)对催化剂进行了表征。用自制固定床评价了催化剂活性。结果表明,添加CaO后,催化剂路易斯酸性和表面碱性增强;催化剂母体中高温碳酸盐含量增加,热稳定性增强,CuO颗粒粒径变小,Cu-Zn协同作用增强,Cu比表面积增大,分散性变好。催化剂活性受到表面酸碱性、铜比表面积、Cu-Zn协同作用和铜分散性共同影响。当CaO为2%时,铜比表面积为79.3 m2/g、铜分散度为34.8%、CO_2转化率为24.55%、甲醇选择性为19.01%、甲醇收率为0.044 g/(gcat·h),催化剂活性最好。过量CaO占据催化剂孔道和覆盖表面活性位,使催化剂路易斯酸性和表面碱性过强,CuO与H_2有效接触减少,CO_2难以脱附,催化活性下降。因此,适量CaO(2%)添加可促进CO_2加氢反应合成甲醇。     

Cu@UiO-66衍生的Cu+-ZrO2界面位点用于高效催化CO2加氢制甲醇

Cu/ZrO₂ catalysts have demonstrated effective in hydrogenation of CO₂ to methanol, during which the Cu-ZrO₂ interface plays a key role. Thus, maximizing the number of Cu-ZrO₂ interface active sites is an effective strategy to develop ideal catalysts. This can be achieved by controlling the active metal size and employing porous supports. Metal-organic frameworks (MOFs) are valid candidates because of their rich, open-framework structures and tunable compositions. UiO-66 is a rigid metal-organic skeleton material with excellent hydrothermal and chemical stability that comprises Zr as the metal center and terephthalic acid (H₂BDC) as the organic ligand. Herein, porous UiO-66 was chosen as the ZrO₂ precursor, which can confine Cu nanoparticles within its pores/defects. As a result, we constructed a Cu-ZrO₂ nanocomposite catalyst with high activity for CO₂ hydrogenation to methanol. Many active interfaces could form when the catalysts were calcined at a moderate temperature, and the active interface was optimized by adjusting the calcination temperature and active metal size. Furthermore, the Cu-ZrO₂ interface remained after CO₂ hydrogenation to methanol, as confirmed by transmission electron microscopy (TEM), demonstrating the stability of the active interface. The catalyst structure and hydrogenation activity were influenced by the content of the active component and the calcination temperature; therefore, these parameters were explored to obtain an optimized catalyst. At 280 ℃ and 4.5 MPa, the optimized CZ-0.5-400 catalyst gave the highest methanol turnover frequency (TOF) of 13.4 h^-1 with a methanol space-time yield (STY) of 587.8 g·kg^-1·h^-1 (calculated per kilogram of catalyst, the same below), a CO₂ conversion of 12.6%, and a methanol selectivity of 62.4%. In situ diffuse-reflectance infrared Fourier transform spectroscopy (DRIFTS) of CO adsorption over the optimized catalyst revealed a predominant, unreducible Cu⁺ species that was also identified by X-ray photoelectron spectroscopy (XPS). The favorable activity observed was due to this abundant Cu⁺ species coming from the Cu⁺-ZrO₂ interface that served as the methanol synthesis active center and acted as a bridge for transporting hydrogen from the active Cu species to ZrO₂. In addition, the oxygen vacancies of ZrO₂ promoted the adsorption and activation of CO₂. These vacancies and Cu⁺ trapped in the ZrO₂ lattice are the active sites for methanol synthesis from CO₂ hydrogenation. The X-ray diffraction (XRD) patterns of the catalyst before and after reaction revealed the stability of its structure, which was further verified by time-on-stream (TOS) tests. Furthermore, in situ DRIFTS and temperature-programmed surface reaction-mass spectroscopy (TPSR-MS) revealed the reaction mechanism of CO₂ hydrogenation to methanol, which followed an HCOO-intermediated pathway.     

Selective hydrogenation of dimethyl maleate to tetrahydrofuran over Cu/SiO2 catalyst: Effect of Cu+ on the catalytic performance

Cu/SiO_2 catalysts prepared by different methods have been investigated focusing on the influence of Cu~+on the catalytic performance.The composition,structure and copper valence state were characterized by means of BET,XRD,XPS,FTIR,N_2O-titration.It was found that the Cu/SiO_2 prepared by ammoniaevaporation(AE) method had much higher TOF value than that prepared by wetness-impregnation(WI)with the same THF selectivity.The higher TOF value was attributed to the coexistence of Cu~+ and Cu~0species in the activated AE-Cu/SiO_2.while only Cu° species existing in the activated Wl-Cu/SiO_2.Researches suggest that Cu~+ can adsorb and polarize the C=0 bond of DMM.It is concluded that Cu°could be the main active site and the synergistic effect between Cu~0 and Cu~+ could contribute to hydrogenation of DMM to THF.     

Cu/SiO2催化剂结构对乙酸甲酯加氢性能的影响

采用尿素水解法制备了Cu/SiO₂催化剂, 探究其用于乙酸甲酯(MA)加氢制取乙醇的催化性能, 并通过N₂物理吸附、X射线衍射(XRD)、程序升温还原(TPR)、透射电子显微镜(TEM)和X射线光电子能谱(XPS)等表征方法分析了催化剂的物理化学特性, 探究了铜负载量和还原温度等对催化剂结构的影响, 以及与催化活性之间的关系. 发现在铜负载量分别为10%、20%和30% (质量分数, w)的催化剂中, 铜负载量为20%的催化剂因具有较多且分散均匀的活性组分而表现出最佳的加氢效果. 接着在铜负载量为20%的催化剂上研究了还原温度(270, 350, 450 ℃)对催化性能的影响, 发现在350 ℃下还原的催化剂活性最高, 在最佳的反应条件下, 乙酸甲酯转化率达到97.8%, 乙醇选择性达到64.9% (理论最大值为66.6%), 主要归属于它具有较高的铜物种分散度, 最合适的Cu⁰/(Cu⁰+Cu⁺)摩尔比例, 同时实现了解离氢气和活化乙酸甲酯的功能.     

Catalytic Performance and Texture of TEOS Based Cu/SiO2 Catalysts for Hydrogenation of Dimethyl Oxalate to Ethylene Glycol

Highly active and selective Cu/SiO₂ catalysts for hydrogenation of dimethyl oxalate(DMO) to ethylene glycol(EG) were successfully prepared by means of a convenient one-pot synthetic method with tetraethoxysilane( TEOS) as the source of silica. XRD, H₂-TPR, SEM, TEM, XRF and N₂ physisorption measurements were performed to characterize the texture and structure of Cu/SiO2 catalysts with different copper loadings. The active components were highly dispersed on SiO₂ supports. Furthermore, the coexistence of Cu⁰ and Cu⁺ contributed a lot to the excellent performance of Cu-TEOS catalysts. The DMO conversion reached 100% and the EG selectivity reached 95% at 498 K and 2 MPa with a high liquid hourly space velocity over the 27-Cu-TEOS catalyst with an actual copper loading of 19.0%(mass fraction).     

催化剂表面Cu0含量对二氧化碳加氢合成C2+醇性能的影响

通过在空气气氛下焙烧Cu@Fe-MIL-88B MOF材料制备了CuFe组分均匀分散的催化剂前驱物, 该前驱物经过不同温度下的预还原制得表面具有不同Cu和Fe价态分布的系列催化剂. 将所制备的催化剂用于固定床反应器上CO₂加氢合成C₂₊醇的性能研究, 并结合催化剂的X射线衍射(XRD)、 X射线光电子能谱(XPS)、 氢气程序升温还原(H₂-TPR)、 氮气吸附-脱附、 扫描电子显微镜(SEM) 和高分辨率透射电子显微镜(HRTEM)等表征结果发现, 较高的还原温度增加了催化剂表面低价态的Cu和Fe的含量; 当还原温度为350 ℃时, 催化剂表面Cu⁰/(Cu⁺+Cu⁰)摩尔比为73.9%, 单质Fe摩尔分数为0.40%, 催化效果最好, CO₂转化率达到6.82%, 总醇选择性为39.4%, 其中C₂₊醇的摩尔比达到95.1%.     

ZnO逆修饰小尺寸Cu/SiO2催化剂及其在CO2加氢制甲醇中的应用

Cu-ZnO is broadly used as a catalyst in CO₂ reduction to produce methanol, but fabricating small-sized Cu-ZnO catalysts with strong Cu-ZnO interactions remains a challenge. In this work, a simple, low-cost method is proposed to synthesize small-sized Cu-ZnO/SiO₂ with high activity and controllable Cu-ZnO interactions derived from copper silicate nanotubes. A series of Cu-ZnO/SiO₂ samples with different amounts of ZnO were prepared. The activities of the as-prepared catalysts for methanol synthesis were tested, and the results revealed a volcano relationship with the weight fraction of ZnO. At 523 K, the methanol selectivity increased from 20% to 67% when 14% ZnO was added to the Cu/SiO₂ catalyst, while the conversion of CO₂ increased first and then decreased with the addition of ZnO. The optimum space time yield (STY) of 244 g·kg^-1·h^-1 was obtained on C-SiO₂-7%ZnO at 543 K under 4.5 MPa H₂/CO₂. Furthermore, the synergistic effect of Cu and ZnO was studied by high resolution transmission electron microscopy (HRTEM), powder X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), in situ diffuse-reflectance infrared Fourier transform spectroscopy (DRIFTS), and temperature-programmed reduction (TPR) analyses. The HRTEM images showed that the Cu particles come in contact with ZnO more frequently with increased addition of ZnO, indicating that the catalysts with higher ZnO contents have a greater probability of formation of the Cu-ZnO interface, which promotes the catalytical activity of Cu-ZnO/SiO₂. Meanwhile, the HRTEM images, XRD patterns, and TPR results showed that the addition of excess ZnO leads to an increase in the size of the Cu particles, which in turn decreases the total number of active sites and further degrades the activity of the catalysts. The activation energy (E_a) for methanol synthesis and reverse water gas shift (RWGS) was calculated based on the results of the catalytical test. With the addition of ZnO, E_a for methanol synthesis decreased from 72.5 to 34.8 kJ·mol^-1, while that for RWGS increased from 61.3 to 102.7 kJ·mol^-1, illustrating that ZnO promotes the synergistic effect of Cu-ZnO. The results of XPS and in situ DRIFTS showed that the amount of Cu⁺ species decreases with the addition of ZnO, indicating that the Cu-ZnO interface serves as the active site. The Cu surface area and the turnover frequency (TOF) of methanol were calculated based on the H₂-TPR curves. The TOF of methanol on the Cu-ZnO/SiO₂ catalysts at 543 K increased from 1.5 × 10^-3 to 3.9 × 10^-3 s^-1 with the addition of ZnO, which further confirmed the promotion effect of the Cu-ZnO interface on the methanol synthesis. This study provides a method to construct Cu-ZnO interfaces based on copper silicate and to investigate the influence of ZnO on Cu-ZnO/SiO₂ catalysts.     

铝添加量对Cu/ZnO/Al_2O_3甲醇合成催化剂性能的影响

采用分步沉淀法制备出一系列不同铝含量的催化剂样品,通过X射线衍射(XRD)、热重-质谱(TG-MS)、荧光光谱仪(XRF)、N_2物理吸附、氢气程序升温还原(H_2-TPR)对样品进行表征,考察了不同铝添加量对铜基甲醇催化剂性能的影响。结果表明,铝元素的添加对前驱物中碱式碳酸盐组分产生作用,促进了焙烧后样品中高温碳酸盐的形成,进而影响到催化剂的性能。随着铝元素的添加,焙烧后催化剂的比表面积、催化剂活性和热稳定性均有增加。当Al~(3+)/(Cu~(2+)+Zn~(2+)+Al~(3+))物质的量比增加至30%时,催化剂在230℃、4 MPa和合成气(13%CO、1.2%CO_2、80%H_2、5.8%Ar)的评价条件下,热处理前后的CO转化率分别为76%和67%,仍保持着较高的活性和热稳定性。     

Cu-Ni-Al尖晶石催化甲醇重整制氢:Al含量的影响

采用固相球磨法制备了Al含量不等的Cu-Ni-Al三元尖晶石固溶体催化剂，通过BET、XRD、H₂-TPR、XPS表征和催化性能评价，研究了Al含量对Cu-Ni-Al尖晶石的物化性质和甲醇制氢缓释催化性能的影响。结果表明，恒定Cu：Ni（molar ratio）=0.95：0.05，增加Al含量时（Al=2、3、4），所得催化剂的比表面积和孔体积都明显增大，且尖晶石晶胞常数和晶粒尺寸均减小，催化剂也变得难以还原。进一步研究发现，随着Al含量增加，尖晶石Ni²⁺含量略微增加，但尖晶石Cu²⁺含量大幅降低，因此，尖晶石结构中Cu²⁺和Ni²⁺的总量降低，表明Ni²⁺的存在抑制了Cu²⁺进入尖晶石结构。表面分析结果证实，Al含量增加导致催化剂表面由富Cu转变为富Al，表层尖晶石Cu²⁺含量降低，但仍高于体相含量。评价结果显示，随着Al含量增加，反应初始活性增大，CO选择性降低，但Al过量太多时催化稳定性降低，综合来说，Al=3的催化剂表现出较好的催化性能。结果表明，对于Cu-Ni-Al尖晶石缓释催化剂，存在最佳Al含量，对催化稳定性起到关键作用。