双异质诱导层对红荧烯薄膜晶体管性能的影响

在二氧化硅衬底上依次真空沉积p-六联苯(p-6P)和酞菁铜(CuPc)构成双异质诱导层,研究了不同衬底温度下双异质诱导层对红荧烯薄膜形貌的影响,以及红荧烯分子在双异质诱导层上的生长过程.分析发现,第二诱导层酞菁铜的局部有序性对红荧烯薄膜的结晶度有直接影响.随着衬底温度的升高,酞菁铜薄膜有序区域面积增大,红荧烯的棒状晶粒也逐渐增大.当酞菁铜和红荧烯的衬底温度均为90℃,红荧烯蒸镀厚度为20 nm时,红荧烯薄膜形成高度有序、内部连接及具有特定方向的棒状晶畴.利用X射线衍射(XRD)和透射电子显微镜(TEM)分析了红荧烯薄膜的晶体结构,发现经过双异质诱导后的红荧烯薄膜转变为多晶形态.另外,红荧烯薄膜晶体管性能也明显提高,开态电流提高了约3个数量级,迁移率提高了30倍,阈值电压降低了20 V.     

氧化锌有序结构在Au(111)和Cu(111)上的生长

利用NO₂或O₂作为氧化剂,研究了氧化锌在Au(111)和Cu(111)上的生长和结构。NO₂表现了更好的氧化性能,有利于有序氧化锌纳米结构或薄膜的生长。在Au(111)和Cu(111)这两个表面上,化学计量比氧化锌都形成非极性的平面化ZnO(0001)的表面结构。在Au(111)上,NO₂气氛下室温沉积锌倾向于形成双层氧化锌纳米结构;而在更高的沉积温度下,在NO₂气氛中沉积锌则可同时观测到单层和双层氧化锌纳米结构。O₂作为氧化剂时可导致形成亚化学计量比的ZnO_x结构。由于铜和锌之间的强相互作用会促进锌的体相扩散,并且铜表面可以被氧化形成表面氧化物,整层氧化锌在Cu(111)上的生长相当困难。我们通过使用NO₂作为氧化剂解决了这个问题,生长出了覆盖Cu(111)表面的满层有序氧化锌薄膜。这些有序氧化锌薄膜表面显示出莫尔条纹,表明存在一个ZnO和Cu(111)之间的莫尔超晶格。实验上观察到的超晶格结构与最近理论计算提出的Cu(111)上的氧化锌薄膜结构相符,具有最小应力。我们的研究表明,氧化锌薄膜的表界面结构可能会随氧化程度或氧化剂的不同而变化,而Cu(111)的表面氧化也可能影响氧化锌的生长。当Cu(111)表面被预氧化成铜表面氧化物时,ZnO_x的生长模式会发生变化,锌原子会受到铜氧化物晶格的限域形成单位点锌。我们的研究表明了氧化锌的生长需要抑制锌向金属基底的扩散,并阻止亚化学计量比ZnO_x的形成。因此,使用原子氧源有利于在Au(111)和Cu(111)表面上生长有序氧化锌薄膜。     

电沉积Cu2xIn2-2xSe2薄膜的光电化学研究

用电沉积法制得Cu_2xIn_2-2xSe₂(铜铟硒)(0[1]并用EDAX对其组成进行分析。对薄膜电极的光电化学性能、光谱响应、能隙与x的依赖关系进行了研究。借助于现场微区扫描光电流谱观察了热处理、薄膜厚度、光极化对薄膜电极的光电性能影响。研究了Pb(NO₃)₂有效的浸渍对薄膜光电性能的影响。     

二维金属-六亚氨基苯框架材料的气体吸附效应

利用密度泛函理论研究了气体分子(NH₃, H₂O, H₂S, NO₂)吸附在二维M₃(HIB)₂(M=Ni, Cu; HIB为六亚氨基苯)薄膜上体系的几何结构和电子结构的变化. 结果表明, 2种薄膜对气体分子的响应不同. 其中NH₃, H₂O和H₂S在M₃(HIB)₂薄膜表面的吸附较弱, 主要与薄膜的亚氨基形成氢键, 吸附能均小于-0.36 eV, 吸附对体系电子性质的影响很小. 但是 NO₂分子在薄膜表面形成化学吸附, 吸附能在-0.65~-1.72 eV范围内. 吸附NO₂分子使其电子结构发生明显改变, 如Cu₃(HIB)₂在费米能级处打开带隙, 由金属性质转变为半导体性质. 这是由于NO₂分子的p_z轨道与金属原子$d_{z}^{2}$ 轨道发生了强烈的轨道杂化. 此外, 研究发现高浓度的NO₂分子吸附能够使Ni₃(HIB)₂薄膜由非磁性变为磁性体系, 由普通金属性质变为半金属性质; 而高浓度的NO₂分子使Cu₃(HIB)₂薄膜由金属性质变为半导体性质, 薄膜电导率降低.     

铜掺杂与氮化碳复合氧化锌材料结构和二氧化氮气体传感性质的密度泛函理论计算

氮氧化物已引发环境污染和危害人类健康等诸多问题.然而,氧化锌基传感器件在监测时存在响应和恢复时间长、核心材料和传感反应过程中间体结构不明确、传感机制不清楚等缺点.为应对这些挑战,采用了全电子密度泛函理论探索铜掺杂氧化锌(标记为ZOC)及其复合物材料的结构和对NO₂的传感反应;计算了复合物ZOC/CN和ZOC/Gr,并与纯ZnO进行对比,其中CN和Gr分别代表二维材料石墨型氮化碳和石墨烯.计算显示, ZOC具有Cu-Zn杂核双金属活性吸附位点;铜的引入增大了金属成分对最前线占据轨道贡献,使得ZOC可同时通过Cu/Zn-O供体作用和反馈供体作用吸附NO₂;其吸附自由能相比ZnO增大0.27 eV.这很好地解释了铜掺杂氧化锌有更快NO₂响应时间的实验结果.进一步复合CN能够提高NO₂传感性能:ZOC/CN具有最大的NO₂吸附能、很小的吸附第二个NO₂上坡能(决速步)和较大的硝酸盐生成能.通过电子结构、反应能和界面相互作用计算,揭示了传感NO₂     

电沉积表面修饰对染料敏化太阳电池微观性能影响机理研究

为了改善染料敏化太阳电池内电子的传输复合过程, 研究者尝试不同方法制备或改性TiO₂薄膜. 对TiO₂薄膜进行后处理, 在其表面引入一层小颗粒层, 是一种有效的方法并被广泛研究. 通过对TiO₂薄膜不同时间的电沉积表面修饰, 细致研究了表面修饰后染料敏化太阳电池微观性能的变化机制. 采用阳极氧化法在TiCl₃水溶液中对TiO₂薄膜进行电沉积后处理, 将溶液pH值调至2.2, 装置的反应速率由恒电位仪控制. 不同沉积时间电池带边移动以及电子传输复合的动力学过程, 借助强度调制光电流谱(IMPS)/强度调制光电压谱(IMVS)和电化学阻抗谱(EIS)等探测技术表征. 研究表明, 电沉积在TiO₂薄膜表面引入了大量浅能级陷阱态, 以致电势较高时电容随沉积时间延长增加明显. 不同时间的电沉积表面修饰在TiO₂薄膜表面形成了新的小颗粒层并改善了TiO₂颗粒间接触, 在改善电子注入及收集过程的同时, 也有效抑制了内部电子复合. IMPS/IMVS结果表明, 电沉积对动力学过程改善的效果受光强影响明显, 弱光下作用更为突出. 此外, 电池开路电压主要受带边移动及内部复合变化影响, 随沉积时间延长, 表面电荷的增多使TiO₂薄膜带边逐渐正移, 有效改善了光电流却限制了开路电压的提升. 在适合的电沉积时间下, 电沉积表面修饰可以同时改善光电流和光电压.     

新型双核铜金属配合物为中性载体的硫氰酸根离子高选择性电极的研究

研制了基于N,N'-亚乙基(μ-5,5-亚甲基-二水杨醛根)(乙酰丙酮根)合二铜(II) [Cu₂(II)-MDSBAE]金属配合物为中性载体的阴离子选择性电极. 试验表明, 以Cu₂(II)-MDSBAE金属配合物为中性载体的电极对SCN^－具有良好的电位响应特性, 且呈现反Hofmeister行为,其选择性序列为: SCN^－＞Sal^－＞I^－＞ClO₄^－＞NO₃^－＞Br^－＞NO₂^－＞Cl^－≈SO₃^2－＞SO₄^2－. 在pH 5.0的磷酸盐缓冲体系中, 电极电位呈现近能斯特响应, 线性响应范围为1.0×10^－6～1.0×10^－1 mol/L, 斜率为－53. 6 mV/dec (25 ℃), 检测下限为8.1×10^－7 mol/L. 用交流阻抗研究了电极的响应机理, 并用紫外可见光谱技术测定了电极载体与SCN^－, Sal^－, I^－, ClO₄^－和NO₃^－离子间的配位数及缔合常数. 将该电极用于实验室废水和工业废水中硫氰酸根的检测, 其结果令人满意.     

硝酸异丙酯与Cl原子、 OH和NO3自由基反应的机理及动力学

采用CCSD(T)//M06-2X/6-311++G(d,p)方法, 结合传统过渡态理论, 研究了硝酸异丙酯与Cl原子、 OH及NO₃自由基的反应机理和动力学. 两个反应物单体首先形成氢键复合物, 随后X(X=Cl原子、 OH和NO₃自由基)提取硝酸异丙酯中叔碳的α-H原子或甲基的β-H原子, 室温下, 以X提取α-H原子为主. 反应的主要历程为 Cl原子(OH或NO₃自由基)提取(CH₃)₂CHONO₂的α-H原子, 生成HCl(H₂O或HNO₃)分子和(CH₃)₂CONO₂自由基, 后者分解为丙酮和NO₂. 结果表明, 在200~500 K温度范围内, 随着温度的升高, 丙酮和NO₂的产率降低; 在室温下, 硝酸异丙酯与Cl原子、 OH和NO₃自由基反应的速率常数分别为3.933×10^-11, 1.182×10^-13和7.134×10^-19 cm³·molecule^-1·s^-1. 计算所得硝酸异丙酯与OH自由基反应的动力学数据与实验结论一致.     

镍-氧化镍/铜-氧化亚铜复合纳米粒子修饰玻碳电极测定过氧化氢

在含镍离子和铜离子的溶液中用循环伏安法在玻碳电极(GCE)表面电化学沉积一层镍-氧化镍及铜-氧化亚铜纳米粒子 ( Ni /NiO、 Cu/Cu₂O),在-0.3 V电位条件下,该传感器能催化还原H₂O₂。用安培法测定H₂O₂的响应电流与浓度在2.5×10^-6 ~2.8×10^-3 mol/L范围内呈线性关系,研究了各种实验条件对H₂O₂传感器性能的影响。该传感器制作简单, 使用寿命长,在实际试样的回收率测定中,结果满意。     

二氧化碳刺激响应的荧光传感器*

CO₂刺激响应聚合物作为一种智能刺激响应材料,因其在可逆的调控过程中通常只涉及CO₂气体的通入和排出而具有广泛的应用前景。CO₂荧光传感器是将CO₂的浓度变化转化为可检测到的荧光信号,可实现对CO₂浓度的实时监测和可逆调控,也有助于我国如期实现2030年前碳达峰和2060年前碳中和的生态文明建设目标。本文简要介绍CO₂刺激响应物质的基本原理和常见分类方式,阐述该类物质在构筑荧光传感器方面的妙用,围绕响应灵敏性、响应速率、循环使用性和抗干扰性等传感性能指标的研究成果进行讨论。最后对CO₂刺激响应荧光传感器的改进方向和应用前景进行了展望。     

Substituent effects on the frontier molecular orbitais of aryl isonitriles

An investigation of the frontier molecular orbitais ofo- and p-RC₆H₄NC (R=H, CH₃, NO₂, F, Cl, CF₃, OCH₃) was carried out so that a thorough understanding of the intricacies of σ donation and π acceptance could be developed and used to modify subtly the electron density on metal centers. The results of this study-Indicate that the substituent position (ortho vs. para ) does alter the electron density in the ligand appreciably and that substitution of the phenyl ring with the groups indicated has a smaller effect on the σ-donating ability than it does on the π-accepting ability of the isonitrile ligand.

The π-accepting abilities of the isonitrile ligands increase in the order o-, p-CH₃OC₆H₄NC, o-, p-CH₃C₆H₄NC, o-, p-C₆H₅NC, o-, p-FC₆H₄NC, o-, p-CF₃C₆NC, o-, p-ClC₆H₄NC, o-, p-NO₂C₆H₄NC while the σ-donating ability decreases in this order. The energies of the σ-donor and π-acceptor orbitais are shown to correlate well with observed E values of Cr(RC₆H₄NC)₆ and Mn(RC₆H₄NC)₆⁺¹ complexes. This demonstrates how the theoretical results can be useful in understanding the observed physical properties of isonitrile-metal complexes.     

Tetrakis-4-(2,4-di-tertamylphenoxy)phthalo-cyaninato-polysiloxane Langmuir-Blodgett Films and Their Gas Sensitive Properties

Tetrakis-4-(2,4-di-amylphenoxy) phthalocyaninato-polysiloxane (R₁PcPS) Langmuir-Blodgett (LB) films were prepared onto planar interdigital microelectrode arrays and their pas sensitive, properties were investigated. The results of response and recovery process were Shown when the (R₁PcPS) LB films were exposed to NH₃, NO₂ and I₂ gas in air. THh gas sensitive sensor consisting of (R₁PcPS) LB film can be used to detect NH₃ gas down to 0.0005% in air.     

电活性铁氰化镍膜电极对稀土钇的电控离子分离

通过电沉积方法分别在镀铂石英晶片和铂基底上制备了电活性铁氰化镍膜,并考察了膜电极在含钇离子溶液中的电控离子交换性能. 在0.1 mol·L^-1的硝酸钇溶液中,使用循环伏安法及石英晶体微天平技术测试考察了铁氰化镍膜对钇离子的置入释放性能及对应的质量变化,同时比较了铁氰化镍膜电极在Y(NO₃)₃和Sr(NO₃)₂溶液中的电化学性能. 在0.1 mol·L^-1 [Y(NO₃)₃ + Sr(NO₃)₂]混合溶液中,通过循环伏安法分析了薄膜对Y³⁺/Sr²⁺离子的选择性. 用扫描电子显微镜观察了铁氰化镍膜的表面形貌,并通过X射线光电子能谱仪测定了膜在氧化和还原状态下的元素组成. 结果表明,铁氰化镍膜在含Y³⁺溶液中具有良好的离子交换行为,其中氧化过程薄膜质量减少,对应着钇离子的释放;还原过程薄膜质量增加,对应钇离子的置入;在0.0 V或0.9 V调控膜电极的氧化还原状态实现对钇离子的有效分离.     

Catalytic selective oxidation of benzyl alcohols to aldehydes with rhenium complexes

The system (ⁿBu₄N)ReO₄ 5/PhIO/CH₂Cl₂, T = 298 K catalyses effectively and with total selectivity the anaerobic oxidation of a range of primary substituted benzyl alcohols (o-, m-, p-X-C₆H₄-CH₂OH, X = H, Me, MeO, Cl, NO₂, CF₃) to the corresponding aldehydes; in contrast, it is unreactive towards secondary benzyl and aliphatic (primary and secondary) alcohols. This may prove of interest in synthetic organic transformations, when several alcoholic functionalities are present in the same molecule.     

Substrate-induced anisotropy of c-axis textured NaxCoO2 thin films

Na_xCoO₂ [x = 0.51, 0.54, and 0.59] thin films have been grown on SrTiO₃ (100)-oriented single crystals with a 5° vicinal cut towards [010] by pulsed laser deposition. We analysed the films by X-ray diffractometry, atomic force microscopy (AFM), and dc-transport measurements. X-ray diffraction patterns of the films show single phase and c-axis textured growth with the film plane closely aligned to the [001]-direction of 5° miscut SrTiO₃ (001) substrates. In addition to the structural analysis of these films we performed transport measurements along and perpendicular to the substrate tilt direction and determined the resistivity anisotropy as a function of temperature. The results enable the development of a strategy for the fabrication of Na_xCoO₂ based thermoelectric thin film devices.     

脉冲激光沉积LiFePO4阴极薄膜材料及其电化学性能

采用脉冲激光沉积结合高温退火的方法在不锈钢基片上制备了LiFePO₄薄膜电极. XRD谱图显示, 经650 ℃退火制得的是具有橄榄石结构的LiFePO₄薄膜. 充放电测试表明, LiFePO₄薄膜具有3.45/3.40 V的充放电平台, 与LiFePO₄粉体材料相当. 首次放电容量约为27 mAh•g^－1, 充放电循环100次后容量衰减51%.     

Systematische untersuchungen über das verhalten von organozinnverbindungen gegenüber flüssigem schwefeldioxid II. Reaktionen von arylstannanen mit flüssigem SO2

The behaviour of tetraarylstannanes, R₄Sn (R = C₆H₅CH₂, C₆H₅, o-, m-, p-CH₃C₆H₄), towards SO₂ under various conditions has now been studied in detail. Compared to aliphatic tetraorganostannanes, the variability of the reaction products is much less, so that in nearly all cases only disulfinates, R₂Sn(O₂SR)₂, are formed. The aromatic tin(IV) mono-, di- and tri-sulfinates are also obtained by metathetical reaction between the corresponding organotin halides and sodium sulfinates. A unique feature of triaryltin chlorides, R₃SnCl (R = C₆H₅, o-, m-, p-CH₃C₆H₄), is their disproportionation in liquid SO₂ leading to disulfinates, R₂Sn(O₂SR)₂, and dichlorides, R₂SnCl₂. (p-CH₃C₆H₄)₂SnCl₂, under more efficient conditions, also accepts SO₂ forming (p-CH₃C₆H₄SO₂)₂SnCl₂. The structural investigations of the newly prepared compounds are carried out on the basis of their IR and ¹H NMR spectra.     

Properties of chemical vapour deposited nanocrystalline TiO2 thin films and their use in dye-sensitized solar cells

Nanocrystalline titanium dioxide (TiO₂) thin films have been prepared using titanium(IV) isopropoxide as a precursor onto the glass and fluorine doped tin oxide coated glass substrates by chemical vapour deposition technique at 400 °C substrate temperature. X-ray diffraction study confirms the polycrystalline nature of TiO₂ with anatase phase having tetragonal crystal structure. The films are 975 nm thick and transparent having transmittance grater than 80%. Atomic force microscopy (AFM) images reveal the nanocrystalline morphology with grain size of 200 nm. The film shows a sharp absorption edge near 350 nm. Photoelectrochemical study shows that TiO₂ thin film sensitized with Brown Orange dye is found to exhibit relatively maximum I_sc and V_oc among the studied dyes. The values of fill factor (FF) and efficiency (η) for the dye-sensitized solar cell (Brown Orange dye-sensitized TiO₂) are 0.54 and 0.17%, respectively. Such films would serve as better prospects for dye-sensitized solar cells.     

Preparation of epitaxial La0.6Ca0.4Mn1−xFexO3 (x = 0, 0.2) thin films: Variation of the oxygen content

Perovskite thin films with a nominal composition of La_0.6Ca_0.4Mn_1−xFe_xO₃ (x = 0, 0.2) were deposited by pulsed reactive crossed beam laser ablation. The film properties, such as electrical conductivity and magnetoresistance are studied as a function of the oxygen content and substrate type. The oxygen content of the thin films was determined by Rutherford Backscattering and controlled by varying the background gas pressure, pressure of the gas pulse and by using alternatively O₂ and N₂O as the gas pulse.

LaAlO₃ and SrTiO₃ were used as substrates at deposition temperature of 650 °C. The grown films were analyzed by X-ray diffraction in order to optimize the growth conditions, i.e. to obtain epitaxial thin films. Thin films doped with 20% Fe were grown under the same experimental conditions as the undoped LCMO films and the effect of the doping on the structural and transport properties of the thin films has been investigated.

The temperature of the metal–insulator transition was measured as a function of the oxygen content and substrate type.