室温下电化学活化CO2与环氧化合物反应合成环碳酸酯

室温下用铝为牺牲阳极, 以四丁基溴化铵/N,N-二甲基甲酰胺作电解质溶液, 在无隔膜电解池中电化学活化CO₂, 与环氧化合物反应, 合成了环状碳酸酯. 考察了不同电极材料、导电盐、CO₂的压力以及溶剂等因素对电合成结果的影响, 结果表明以Pt为阴极, 在0.05 mol•L^－1 Bu₄NBr/DMF电解质溶液中和4 MPa CO₂下, 环状碳酸酯产率可高达65%～98%.     

手性β-氨基醇的合成及其催化二乙基锌与醛的不对称加成反应

以烯烃为原料通过Sharpless不对称双羟化等多步反应合成7种手性β-氨基醇, 并将该类化合物用于催化二乙基锌和醛的不对称加成反应. 分别考察了影响对映选择性的催化剂结构、催化剂用量、溶剂、反应温度等各种因素. 当催化剂用量为5%、甲苯溶剂、在－10 ℃下、以(1S,2R)-(＋)-2-氨基-1,2-二苯基乙醇(1b)作催化剂时, 所得仲醇的对映体过量最高为85% ee, 产率高达100%.     

手性二胺修饰的负载型钌催化剂催化芳香酮不对称加氢

研究了用手性修饰剂(1S,2S)-(－)-1,2-二苯基乙二胺修饰的负载型钌催化剂(Ru/γ-Al₂O₃)催化芳香酮的不对称加氢反应, 在KOH的异丙醇溶液中, 10～20 ℃, p_H2＝5 MPa条件下, 芳香酮及其衍生物加氢产物的ee值达79.5%～85.0%, 2-乙酰基噻吩加氢产物的ee值可达86.2%. 此催化剂制备简单, 容易与产物分离, 重复使用4次, 对映选择性基本保持不变.     

苯二胺和联苯二胺类叔芳胺的合成及发光性能的研究

N,N′-二苯基-1,4-苯二胺和N⁴,N^4'-二苯基-4,4'-联苯二胺分别与芳基溴在Pd(OAc)₂/P(t-Bu)₃催化下于120 ℃邻二甲苯溶液中反应生成苯二胺和联苯二胺类叔芳胺有机电致发光材料, 这些化合物的熔点都在300 ℃以上. 产物的结构经¹H NMR, ¹³C NMR, ¹³C (DEPT), MS (HREI和EI)表征. 用UV-Vis, PL, DSC测定了苯二胺和联苯二胺类叔芳胺化合物的发光性能.     

手性β-氨基醇催化α,β-不饱和酮的不对称环氧化反应

将以烯烃为原料通过Sharpless不对称双羟化等多步反应合成的8种手性β-氨基醇, 作为有机小分子催化剂, 用于催化α,β-不饱和酮的不对称环氧化反应．考察了影响对映选择性的催化剂结构、催化剂用量、氧化剂种类、溶剂、反应温度等因素．结果表明, 当催化剂用量为30 mol%、氧化剂为TBHP(叔丁基过氧化氢)、正己烷溶剂、在室温下、以(1S,2R)-(＋)-1,2-二苯基-2-甲氨基乙醇(3)作催化剂时, 所得环氧化物的对映体过量最高为70% ee, 产率最高为84%.     

N-甲基-2-(4'-N-乙基咔唑基)-[60]富勒烯吡咯烷及其衍生物的合成, 电荷分离态特征

通过1,3-偶极环加成方法在微波照射下合成了N-甲基-2-(4'-N-乙基咔唑基)-富勒烯吡咯烷(C₆₀-Cz)和N-甲基-2- (4'-N,N-二苯基氨基)-富勒烯吡咯烷(C₆₀-TPA), 用质谱, ¹H NMR, IR等对其结构进行了表征. 用激光光解时间分辨瞬态谱研究了N-甲基-2-(4'-N-乙基咔唑基)-富勒烯吡咯烷的分子内电荷转移过程, 在近红外区观测到了长寿命电荷分离态C₆₀^•--C_Z^•+的存在, 其寿命为0.28 μs. 运用Gaussian 98量子化学程序包, 利用密度泛函的方法对N-甲基-2-(4'-N,N-二苯基氨基)-富勒烯吡咯烷几何构型进行了优化, 并在优化基础上用ZINDO方法计算了化合物C₆₀-TPA的电子光谱, 计算结果表明, 光谱吸收峰在440 nm, 与实验值433 nm基本一致.     

纳米Cu2O催化二苯甲烷二氨基甲酸苯酯无溶剂热分解制备二苯甲烷二异氰酸酯

研究了无溶剂条件下纳米Cu₂O催化二苯甲烷二氨基甲酸苯酯(MDPC)热分解制备二苯甲烷二异氰酸酯(MDI),考察了纳米Cu₂O的制备条件与反应条件对MDPC热分解反应性能的影响.结果表明,水解法制备的纳米Cu₂O在Ar中于300℃焙烧2h,其催化性能最佳;最佳的反应条件为Cu₂O用量为原料总重的0.06%,反应温度220℃,反应压力0.6kPa,反应时间12min,此时MDPC转化率达到99.8%,MDI选择性86.2%.     

二丁基氧化锡催化碳酸二甲酯与苯酚酯交换反应机理研究

研究了二丁基氧化锡催化碳酸二甲酯与苯酚酯交换合成碳酸二苯酯的反应机理, 发现原料苯酚和产物DPC都能与二丁基氧化锡生成同一种中间体, 并测定了其晶体结构. 该晶体属于单斜晶系, P2₁/n空间群; 晶胞参数: a＝1.3336(2) nm, b＝1.7208(2) nm, c＝1.3759(3) nm, β＝101.00(2)°; V＝3.0993(9) nm³; D_c＝1.432 g/cm³; Z＝4; F(000)＝1352; μ＝1.635 mm^－1. 分析结果显示该中间体是一种新型的二聚四烃基二锡氧烷化合物[Bu₂Sn(OPh)OSnBu₂O(Ph)]₂ (I), 该化合物具有中心对称的层状结构. MS和XPS结果证实I在酯交换反应条件下能稳定存在. 基于实验结果, 本文提出了一个合理的酯交换反应机理.     

电化学还原合成1,5-二氨基萘

研究了以1,5-二硝基萘为原料电化学还原合成1,5-二氨基萘的反应. 室温下, 运用循环伏安法研究了1,5-二硝基萘的循环伏安行为, 1,5-二硝基萘的还原是一受扩散控制的不可逆反应; 循环伏安图上两个连续的还原峰对应于两个硝基的还原; 求出了反应的传递系数α₁在0.275～0.335之间, α₂在0.360～0.437之间. 探讨了电解电位(E)、底物浓度(c₁)、电解电量(Q)、硫酸浓度(c₂)以及溶剂(DMF)与水的体积比(Y)对产物产率的影响, 在最优条件下1,5-二氨基萘的产率最高可达77%.     

维生素C溶液有氧降解动力学

建立了一种恒温高压氧药物稳定性加速试验方法, 用这种方法可在较短的时间内求得药物氧化反应的动力学参数. 以10%维生素C溶液为例, 维生素C在有氧和无氧条件下均可降解, 总的降解速率常数k_t由两部分构成: k_t＝k_an＋k_ae, k_an为无氧降解速率常数, 可表达为k_an＝A_an•exp(－E_a,an /RT); k_ae为有氧降解速率常数, 可表达为k_ae＝A_ae•exp(－E_a,ae/ RT)• .     

Fe(III)EDTA作为氧化羰化苯酚合成碳酸二苯酯一种有效的氧化还原催化助剂

研究了氧化羰化苯酚合成碳酸二苯酯反应。发现了Fe(III)EDTA 在PdCl2/Fe(III)EDTA/1,4 苯醌/ 四丁基溴化铵催化体系中具有很好的助催化效果。讨论了上述催化体系中的每一组分的作用，并提出了一个催化反应机理。氧化羰化苯酚合成碳酸二苯酯反应的最佳温度为100℃～120℃。当反应在100℃、PCO=2.0MPa、PO2=0.5MPa、苯酚 0.5mol、 PdCl2 0.28mmol、n(PdCl2)∶n(Fe(III)EDTA)∶n(苯醌)∶n(四丁基溴化铵)=1∶1∶10∶40、 4A 分子筛 5.0g、 4h进行时，碳酸二苯酯的产率和选择性分别为8.35%和97.5%。压力越高对生成碳酸二苯酯越有利。     

嫁接Al改性MCM-41介孔分子筛催化合成双酚F

以十六烷基三甲基溴化铵和正硅酸乙酯为原料,合成纯硅MCM-41介孔分子筛。 再利用九水硝酸铝为改性剂来嫁接改性纯硅MCM-41介孔分子筛,NH3-TPD结果表明,嫁接后的AlMCM-41产生了中强酸。 用改性后不同n(Si)/n(Al)的AlMCM-41催化合成双酚F,在n（苯酚）/n（甲醛）=30、反应时间5 h、反应温度90 ℃、m（甲醛）/m（AlMCM-41）=7的反应条件下,在一定范围内,双酚F的产率随Al含量增加而增加,但在n（Si）/n（Al）＜50时,双酚F的产率反而下降,当n（Si）/n（Al）=50时,双酚F的产率最高,为42.28%。     

Copper (II) adsorbed on SiO(2)/SnO(2) obtained by the sol-gel processing method: application as electrochemical sensor for ascorbic acid

With the objective of producing a material showing better conductive properties to be used as a support for electroactive species, a SiO(2)/SnO(2) mixed oxide was prepared. The procedure for SiO(2)/SnO(2) mixed oxide preparation using the sol-gel processing method, starting from tetraethylorthosilicate and SnI(4) as precursor reagents, is described. SiO(2)/SnO(2) with composition Sn=15.6 wt% and S(BET) = 525 m(2)g(-1), V(p)=0.28 mlg(-1), and D(p)= 1.5 nm, where S(BET), V(p) and D(p) are the specific surface area, the average pore volume, and the average pore diameter, respectively, was obtained. The X-ray photoelectron spectroscopy showed that the mixed oxide was thermally very stable for samples heat-treated at up to 1073 K. The Br?nsted acid sites, probed with pyridine molecules for samples heat-treated at various temperatures, were chemically stable up to 473 K. Segregation of SnO(2) crystalline phase was observed at 1473 K but no crystalline phase was verified for SiO(2) at this temperature. The porous SiO(2)/SnO(2) matrix was used as base for Cu(II) immobilization and an electrode was developed for application in electrochemical detection of vitamin C in tablets.     

Zn-Al水滑石催化碳酸二甲酯与苯酚酯交换反应的研究

用共沉淀法制备了Zn-Al水滑石,并用于多相催化酯交换合成碳酸二苯酯的反应.研究了不同n(Zn)/n(Al)比的水滑石及其焙烧产物等对酯交换反应的催化活性.结果表明,Zn-Al水滑石催化剂对该反应的催化活性和选择性很高,当n(Zn)/n(Al)=3时,在150～180℃,n(PhOH)/n(DMC)=2,催化剂用量为反应物总质量的1.5%,在反应时间为12h的条件下,DMC的转化率达到55.9%,DPC和MPC的收率分别为25.3%和27.0%,酯交换产物的选择性达到93.6%.利用XRD,TG-DTA和TEM等手段对催化剂进行了表征.     

Synthesis of 3-(1-Cyclohexenyl)-2-butanone via Environmentally Friendly Catalysts

Introduction3- ( 1 - Cyclohexenyl) - 2 - butanone( CHB) is oneofthe importantchemicals and has a potential valuein perfume industry.Beak et al.[1] reported thatthe acylation of ethylidenecyclohexane( EDC) withzinc chloride as a catalystgave3- ( 1 - cyclohexenyl) -2 - butanone in a good yield,butthey have notmadea more detailed investigation.The use of such aconventional catalyst as zinc chloride leads to anumber of problems such as corrosion,unclean re-action products and the disposal of pot…     

Synthesis,Characterization and in vitro Antitumour Activity of the Di—n—butyltin（IV） Complexes of Some Arylhydroxamates

Fourteen new di-n-butyltin(IV)complexes of hydroxamic acids of the formula Bu2SnL2(HL-hydroxamic acids)were synthesized by the reaction of Bu2SnO and hydroxamic acids in dry toluene and ethanol media.The compounds were characterized by elemental analyses,molecular weight,IR and 1H NMR spectoscopy.The results indicate that n-Bu2SnL2 have distorted trans-octahedral structure.The antitumor activity in vitro against human A-549 tumor cells and P388 leukemia was presented,and their structure-activity relationship was discussed.     

Improved lithium cyclability and storage in mesoporous SnO2 electronically wired with very low concentrations (≤1 %) of reduced graphene oxide

On the wire: Mesoporous tin dioxide (SnO(2)) wired with very low amounts (≤1?%) of reduced graphene oxide (rGO) exhibits a remarkable improvement in lithium-ion battery performance over bare mesoporous or solid nanoparticles of SnO(2). Reversible lithium intercalation into SnO(2)/SnO over several cycles was demonstrated in addition to conventional reversible lithium storage by an alloying reaction.     

Photovoltaic cells using composite nanoclusters of porphyrins and fullerenes with gold nanoparticles

Novel organic solar cells have been prepared using quaternary self-organization of porphyrin (donor) and fullerene (acceptor) units by clusterization with gold nanoparticles on nanostructured SnO2 electrodes. First, porphyrin-alkanethiolate monolayer-protected gold nanoparticles (H2PCnMPC: n is the number of methylene groups in the spacer) are prepared (secondary organization) starting from the primary component (porphyrin-alkanethiol). These porphyrin-modified gold nanoparticles form complexes with fullerene molecules (tertiary organization), and they are clusterized in acetonitrile/toluene mixed solvent (quaternary organization). The highly colored composite clusters can then be assembled as three-dimensional arrays onto nanostructured SnO2 films to afford the OTE/SnO2/(H2PCnMPC+C60)m electrode using an electrophoretic deposition method. The film of the composite clusters with gold nanoparticle exhibits an incident photon-to-photocurrent efficiency (IPCE) as high as 54% and broad photocurrent action spectra (up to 1000 nm). The power conversion efficiency of the OTE/SnO2/(H2PC15MPC+C60)m composite electrode reaches as high as 1.5%, which is 45 times higher than that of the reference system consisting of the both single components of porphyrin and fullerene.     

掺杂TiO2纳米粉的合成、表征及催化性能研究

 考察了制备方法对掺杂Fe2O3,ZrO2或SnO2的TiO2纳米粉的XRD谱及催化性能的影响．结果表明,用共沉淀法制备的Fe2O3·TiO2对其XRD谱强度的影响较大,而负载法制备Fe2O3／TiO2对其XRD谱的强度无影响;两种方法制备的掺杂ZrO2或SnO2的TiO2样品对XRD谱均无影响．TEM结果表明,TiO2纳米粉的晶粒均匀,粒径为14～18nm．苯酚水溶液的光催化氧化分解反应结果表明,与TiO2样品相比,负载型Fe2O3／TiO2的催化活性明显较高,但ZrO2／TiO2,SnO2／TiO2和共沉淀型Fe2O3·TiO2的催化活性变化不大．可以认为,对掺杂Fe2O3的TiO2催化剂,负载法是较好的制备方法．     

Experimental and theoretical studies of the thermal behavior of titanium dioxide-SnO2 based composites

In this paper we report experimental and theoretical studies concerning the thermal behavior of some organotin-Ti(IV) oxides employed as precursors for TiO(2)/SnO(2) semiconducting based composites, with photocatalytic properties. The organotin-TiO(2) supported materials were obtained by chemical reactions of SnBu(3)Cl (Bu = butyl), TiCl(4) with NH(4)OH in ethanol, in order to impregnate organotin oxide in a TiO(2) matrix. A theoretical model was developed to support experimental procedures. The kinetics parameters: frequency factor (A), activation energy, and reaction order (n) can be estimated through artificial intelligence methods. Genetic algorithm, fuzzy logic, and Petri neural nets were used in order to determine the kinetic parameters as a function of temperature. With this in mind, three precursors were prepared in order to obtain composites with Sn/TiO(2) ratios of 0% (1), 15% (2), and 30% (3) in weight, respectively. The thermal behavior of products (1-3) was studied by thermogravimetric experiments in oxygen.