CO2/C3H6O在金属氧化物耦合吡咯氮生物炭表面的共/竞吸附机理研究

本研究采用密度泛函理论,通过比较吸附量、吸附能以及态密度和电荷差分密度的分析,探究了不同金属氧化物耦合吡咯氮生物炭(CN5@MO_x,MO_x=ZnO、CaO、Na₂O)表面CO₂与C₃H₆O(CO₂&C₃H₆O)的吸附机理。首先从CO₂/C₃H₆O单组分方面计算了其在CN5@MO_x表面吸附量和吸附能,计算结果表明,在333 K、100 kPa时CN5@Na₂O表面对CO₂/C₃H₆O单组分吸附量分别为3.65、15.34 mmol/g,吸附能分别为-145.86、-132.47 kJ/mol,均高于CO₂/C₃H₆O单组分在CN5@CaO及CN5@...     

CeO2对CuCl/活性炭吸附剂C2H4/C2H6吸附分离性能促进作用

通过等体积浸渍方法制备了添加CeO₂助剂的用于C₂H₄/C₂H₆吸附分离的CuCl/活性炭(AC)吸附剂,使用氮气吸附-脱附曲线、X射线衍射(XRD)、X射线光电子能谱(XPS)、扫描电子显微镜(SEM)、能量分散X射线光谱(EDX)等分析方法对吸附剂进行了表征.结果表明,吸附剂表面Cu(II)在氮气气氛焙烧过程中被部分还原成Cu(I).重点研究了Ce元素的添加对于吸附剂的C₂H₄/C₂H₆吸附分离性能的影响,等温吸附曲线结果表明添加了CeO₂的吸附剂通过降低乙烷的吸附容量从而显著提高了吸附分离性能. XRD及XPS结果表明,和未添加助剂样品相比,其表面晶体团簇较小,分散性更好, Cu(II)还原程度更高.添加CeO₂的吸附剂样品5Ce50Cu(CeO₂和CuCl2的质量分数(w)分别为5%和50%)获得了最好的吸附分离效果,相对于未添加CeO₂的样品50Cu,其在660 kPa下的吸附选择性由4.2提升到8.7.     

Cu/WO3-TiO2光催化剂上丙烯和二氧化碳合成MAA反应性能

研究了Cu/WO₃-TiO₂对CO₂和C₃H₆的吸附特性和光催化性能.结果表明,在Cu/WO₃-TiO₂催化剂表面存在金属位Cu,Lewis酸位W⁶⁺和Ti⁴⁺以及Lewis碱位W-O-Ti的桥氧和WO的端氧三类活性中心;在金属位Cu和Lewis酸位Ti⁴⁺(或W⁶⁺)的协同作用下,CO₂形成活性较高的卧式吸附态Cu-(CO)-O→Ti⁴⁺(或W⁶⁺),C₃H₆的β-H和β-C分别吸附在Lewis碱位WO与金属位Cu上,形成Cu-(CH₂)C(CH₃)-H→OW吸附态;Cu/WO₃-TiO₂催化剂吸收阈值蓝移和光吸收量的提高均有利于其催化活性的提高,担载质量分数为10%的WO₃光催化剂的催化活性优于其它含量的催化剂,光量子效率最高(19.7%);在383K,0.1MPa,空速200h^-1和125W紫外灯辐照下,C₃H₆转化率为7.4%,甲基丙烯酸(MAA)的选择性超过95%.根据实验结果提出了光促表面催化合成反应的机理.     

过渡金属离子与烷烃反应机理的理论研究──镍离子(2D)与丙烷反应中氢分子的还原消除机理

以Ni⁺与C₃H₈反应作为过渡金属离子与烷烃反应的范例体系,用B₃LYP密度泛函方法计算了[Ni,C₃,H₈]⁺基态势能面上各驻点的构型、频率和能量,结果表明,该反应的H₂分子消除需经历两个基元步骤,即Ni⁺首先插入一级或二级C-H键,然后经H转移过渡态异构化为较稳定的中间体,继而解离产生H₂分子.计算的反应热为142.28kJ/mol,与相应的实验值(127.85kJ/mol)符合较好.     

UTSA-280的氨改性以及C2H4/C2H6分离性能研究

炼厂干气中回收乙烯是扩宽C₂H₄来源的有效途径,但C₂H₄和C₂H₆物理性质和分子尺寸非常接近,分离困难.金属有机骨架材料（MOFs）近年来在低碳烃分离领域展现出广阔的前景.本工作采用氨吸附改性调节UTSA-280的结构,通过一维直孔道大小的调节实现C₂H₄/C₂H₆的高效分离.改性后的UTSA-280具有独特的超微孔结构能提升C₂H₄的吸附,而完全不吸附稍大的C₂H₆,实现理想的C₂H₄/C₂H₆吸附选择性（>1000）.结果表明,改性后的UTSA-280的C₂H₄吸附量可提高至2.83 mmol/g,与未改性的材料相比增加29%,并且能阻挡C₂H₆的吸附,最终达到>1200的C₂H₄/C₂H₆选择性.蒙特卡罗分子模拟（GCMC）计算C₂H₄/C₂H₆混合气体（1：1）的吸附得出,改性后UTSA-280孔内的C₂H₄吸附相比于C₂H₆具有更多的吸附分布.通过C₂H₄/C₂H₆混合气体穿透实验测试,改性后的UTSA-280材料能展现出48 min以上的分离时间,相比于未改性的材料,分离性能提升近1倍.     

H2,C2H4在铂及铂锡合金上化学吸附的量子化学计算

本文详尽地分析了推广的休克尔分子轨道理论方法(EHMO)中参量化过程。借助于计算双原子体系选择出合理的经验参数和近似方式,引进了过渡金属内层原子轨道排斥作用项。分别计算了H,H₂,C₂H₄和C₂H₃在铂及铂锡合金上化学吸附键能,计算结果表明,同铂金属比较,在铂锡合金上H原子,C₂H₄分子的化学吸附键变弱在锡富集的铂锡合金上单个的铂原子不能解离吸附H₂分子,在铂锡合金上C₂H₄脱氢反应较难进行。     

266 nm激光光解C2H5SSC2H5产物的激光诱导荧光光谱

有机硫化物是大气主要污染物之一,其在大气中的光解产物还将造成二次污染,除了存在于有机硫化物中, S―S键还存在于胱氨酸等蛋白质中, S―S键的形成和断裂决定该类蛋白质的活性.本工作中,我们研究了用实验室常见的Nd:YAG激光器的四倍频266 nm激光光解C₂H₅SSC₂H₅过程,通过激光诱导荧光(LIF)光谱方法检测乙硫自由基C₂H₅S等光解产物.实验表明266 nm激光主要光解C₂H₅SSC₂H₅的S―S键产生C₂H₅S自由基.本文应用密度泛函理论的Becke3-Lee-Yang-Parr泛函(B3LYP方法)得到C₂H₅SSC₂H₅的S―S键、C―S键和C―C键的解离势能曲线,可知在266 nm光解条件下, C₂H₅SSC₂H₅在基态能够发生S―S键、C―S键解离, C―C键不发生解离.本文采用全活化空间自洽场(CASSCF)方法优化得到态和态的C₂H₅S自由基结构及其跃迁的绝热激发能,以辅助解析实验检测的C₂H₅S自由基的LIF光谱.实验结合理论计算最终得出,本实验266 nm光解条件下, C₂H₅SSC₂H₅主要发生S―S键解离,不排除少量分子发生C―S键解离的可能性.     

CO和CH3O在Cu2O(111)表面吸附特性及共吸附的理论研究

基于密度泛函理论, 采用广义梯度近似方法结合周期平板模型, 对Cu₂O(111)非极性表面上CO和CH₃O的吸附和共吸附进行了系统的研究. 计算了CO以4种吸附模式和CH₃O以O端在Cu₂O(111)表面上的吸附, 通过对不同吸附位置的吸附能、几何构型参数和Mulliken电荷的计算和比较发现, Cu₂O(111)表面上配位未饱和铜离子(Cu_CUS)为CO的活性吸附位; 配位饱和铜离子(Cu_CSA)为CH₃O的活性吸附位. CO和CH₃O吸附于Cu₂O(111)表面后, 表面弛豫现象明显改善. CO和CH₃O与Cu₂O(111)表面能够形成共吸附体系, CO和CH₃O之间的相互作用力达到75.89 kJ/mol, 为典型的化学作用, 有助于促进CO和CH₃O反应形成表面物种CH₃OCO, 计算结果与实验事实一致.     

C4H6O,C4H6S与XF (X＝F,Cl, Br)分子间卤键的电子密度拓扑研究

运用MP2/aug-cc-pVDZ方法对2,5-二氢呋喃, 2,5-二氢噻吩与XF (X＝F, Cl, Br)之间的卤键作用进行了理论研究. 研究发现: C₄H₆O, C₄H₆S与XF之间不仅存在O(S)…XF n型卤键, C＝C双键与XF分子亦可形成π型卤键|对于C₄H₆O与XF之间的n型和π型卤键以及C₄H₆S与XF之间的π型卤键, 卤键键能ΔE、键鞍点处的电子密度ρ(r_c)以及电子给体到受体之间的电子转移数Δq(XF)均按B…F₂＜B…ClF＜B…BrF (B＝C₄H₆O, C₄H₆S)的顺序依次增大|对于卤键键能较大的体系C₄H₆O…BrF(n), C₄H₆O…BrF(π), C₄H₆S…F₂(n), C₄H₆S…ClF(n), C₄H₆S…BrF(n), C₄H₆S…BrF(π), 卤键作用介于离子键和共价键之间|而对于其它的卤键键能较小的体系, 卤键作用为闭壳层静电作用.     

Cu纳米针上电场促进C-C耦合增强CO2电还原生成C2产物

电催化CO₂减排技术利用电能将过量的CO₂转化为有附加值的化学品,是解决能源危机、实现碳中和的有效途径之一.电催化CO₂还原反应(CO₂RR)中的多碳产物(C₂),如乙烯和乙醇,因其比C1产物具有更高的能量密度和更广泛的应用而受到较大关注.目前为止,Cu基催化剂被认为是获得C₂产物的独特材料.研究者在提高Cu基催化剂C₂产物的活性和选择性方面做了大量的工作,如催化剂形貌工程、活性位点设计和中间吸附性能调控等.许多理论和实验研究已经证明,Cu基催化剂上的C-C偶联过程是C₂产物生成的速率决定步骤.优化C-C偶联过程的能垒是提高C₂产物活性和选择性的重要而直接的策略.CO₂RR在Cu上是由CO₂还原吸附CO(*CO)并二聚生成C₂产物引起的.C-C偶联过程与*CO的吸附性能密切相关.众所周知,CO是一种典型的极性分子,因此其在催化剂表面的吸附性能可能会受到活性位点周围的局部电场的影响.构建合适的局部电场是调节CO吸附性能和C-C偶联过程的潜在手段之一.前期工作(Nature,2016,537,382-386)证明了高曲率金纳米针可以在尖端产生高的局部电场.高局域电场诱导K+聚集,使活性位点周围CO₂浓度升高,大大促进了Au纳米针上的CO生成.基于Au纳米针的局域电场促进了CO₂RR的CO生成.本文利用Cu纳米针促进并优化C-C偶联反应来提高C₂产物活性和选择性.结果表明,局部电场可以促进C-C偶联过程,进而增强CO₂电还原生成C₂产物.有限元模拟结果表明,高曲率铜纳米针处存在较强的局部电场;密度泛函理论计算结果表明,强电场能促进C-C耦合过程.在此基础上,制备了一系列不同曲率的Cu催化剂,其中,Cu纳米针(CuNNs)的曲率最高,Cu纳米棒(CuNRs)和Cu纳米颗粒(CuNPs)曲率次之.实验测得CuNNs上吸附的K+浓度最高,证明了纳米针上的局部电场最强.同时,CO吸附传感器测试表明,CuNNs对CO的吸附能力最强,原位傅里叶变换红外光谱显示,CuNNs的*COCO和*CO信号最强.由此可见,高曲率铜纳米针可以诱导高局部电场,从而促进C-C耦合过程.催化性能测试结果表明,在低电位(-0.6 V vs.RHE)下,Cu NNs对CO₂RR的生成C₂产物的法拉第效率值为44%,约为Cu NPs的2.2倍.综上,本文为CO₂RR过程中提高多碳产物提供了新的思路.     

氯化亚铜在活性炭载体表面单层分散的密度泛函理论计算

 应用量子化学计算方法研究了活性炭载体表面CuCl活性组分的单层分散行为. 以C16H10,C13H9和C12H12原子簇模型模拟活性炭表面,用密度泛函理论中的B3LYP方法计算得到了CuCl在活性炭表面分散的活性位、稳定构型、相互作用能以及单层分散阈值. 结果表明,CuCl以铜端垂直附着在活性炭表面的顶位和桥位上,相互作用能为76.84～80.79 kJ/mol,单层分散阈值为0.471 g/g. 而XRD测得的单层分散阈值为0.467 g/g,与量子化学计算的结果一致; 按照密置单层模型计算得出的单层分散阈值为0.941 g/g,远大于实验测定结果. 因此,应用量子化学计算方法可以得到活性炭表面活性组分单层分散的丰富信息,并能确定活性组分的单层分散阈值.     

多壁碳纳米管对稀土元素的吸附性能

研究了改性多壁碳纳米管(MWCNTs)对稀土元素的吸附。 采用硝酸、次氯酸钠、过氧化氢、高锰酸钾4种方法对MWCNTs进行改性,考察了改性MWCNTs对稀土元素的吸附能力。 采用紫外-可见分光光度法测定稀土元素的浓度,比较了未处理和不同方法处理的MWCNTs对稀土元素的吸附能力。实验结果表明,NaClO改性的MWCNTs对稀土元素的吸附能力最强。以稀土元素钐(Sm)、钆(Gd)、镱(Yb)为代表,研究了NaClO改性MWCNTs对稀土元素的吸附性能。 考察了溶液pH值、离子强度、吸附剂用量、温度等因素对吸附性能的影响。当溶液pH值在2~7范围内,NaClO改性的MWCNTs对Sm、Gd、Yb的吸附随pH值增大而增强。 当离子强度和MWCNTs的用量增大时,对稀土元素的吸附能力降低。3种元素在NaClO改性的MWCNTs上的吸附均为放热过程,其反应焓变ΔH分别为：-6.44、-5.63和8.31 kJ/mol。吸附等温线符合Langmuir和Freundlich等温吸附方程。     

Adsorption of carbon monoxide on Pd low‐index surfaces and (110) reconstructed surface

Adsorption and diffusion of carbon monoxide on Pd low‐index surfaces and missing‐row Pd (110) reconstructed surface have been investigated by the extended London–Eyring–Polyani–Sato (LEPS) method constructed by means of a five‐parameter Morse potential. All critical characteristics, such as adsorption site, adsorption geometry, binding energy, CO vibrational frequency have been obtained and compared with the experimental and theoretical data. On these surfaces, the stable adsorption sites of CO are changed with increasing CO coverage. On the missing‐row Pd (110) reconstructed surface, there are five stable adsorption sites: H₁, H₂ (H₁ and H₂ are threefold hollow sites on (111) subsurface), B (bridge site on the second layer), SB (short‐bridge site), and T (top site). Copyright © 2010 John Wiley & Sons, Ltd.     

Adsorption of p-Nitrophenol in Untreated and Treated Activated Carbon

The adsorption of p-nitrophenol in one untreated activated carbon (F100) and three treated activated carbons (H₂, H₂SO₄ and Urea treated F100) was carried out at undissociated and dissociated conditions.To characterize the carbon, N₂ and CO₂ adsorption were used. X-ray Photoelectron Spectroscopy (XPS) was used to analyze the surface of the activated carbon.The experimental isotherms are fitted via the Langmuir homogenous model and Langmuir binary model. Variation of the model parameters with the solution pH is studied. Both Q _max and the adsorption affinity coefficient (K ₁) were dependent on the PZC of the carbons and solution pH. The Effect of pH must be considered due to its combined effects on the carbon surface and on the solute molecules. Adsorption of p-nitrophenol at higher pH was found to be dependent on the concentration of the anionic form of the solute.     

Removal of H2S from Exhaust Gas by Use of Alkaline Activated Carbon

The purpose of this research was to select an activated carbon and alkaline solution blend that generated the best H₂S adsorption on alkaline-activated carbon. RB₂ (activated carbon) impregnated with NaOH solution was shown to have the optimum H₂S removal efficiency. The optimum NaOH concentration was 50 mg per gram of carbon. H₂S adsorption via RB₂-NaOH₅₀ was five times that of a corresponding fresh-activated carbon. The adsorption equivalent of H₂S is nearly 1 (mol-H₂S/mol-AOH), therefore, H₂S + AOH AHS + H₂O was the major reaction. The H₂S adsorption isotherm corresponded to the Freundlich isotherm.     

A New Radical Initiator of the Binary System of Cupric Methoxide and Carbon Monoxide

Under carbon monoxide pressure, cupric alkoxides such as cupric methoxide, Cu(OCH₃)₂, and cupric acetylacetonate methoxide, Cu(acac)(OCH₃), initiate the polymerization of vinyl monomers. The microstructure of polybutadiene and the composition of styrene-methacrylate copolymer by these catalyst systems have indicated a free radical mechanism. The mechanism of the initiation was examined by the end group of product polymer and the analysis of the reaction between the catalyst components. Reduction of Cu(OCH₃)₂ and Cu(acac)(OCH₃) with carbon monoxide to Cu(OCH₃) and Cu(acac), respectively, was responsible for the initiating activity. The decomposition of these unstable cuprous species produces methoxyl and acetylacetonyl radicals which initiate the polymerization.     

原位化学沉积法制备碳/聚苯胺复合材料作为超级电容器材料的研究

Polyaniline （PA） film was chemically deposited onto the surface of activated carbon （AC） uniformly. Chemical deposition was carried out in 0.1 mol/L aniline plus 0.5 mol/L H2SO4 solution adopting V2O5·nH2O coated on the surface of activated carbon as oxidant. The surface morphologies and structures of the composite materials were characterized by scanning electron microscopy and FT-IR spectra. The electrochemical properties of the composite material electrodes were studied by cyclic voltammetry and constant current charge/discharge tests in 1 molFL H2SO4 solutions. The specific capacitance of composite materials was exhibited as high as 237.5 F/g at a current density of 1.0 A/g compared with a value of 120 F/g for pure carbon electrode. Good power characteristic and good stability of composite electrodes were also demonstrated.     

Kinetics and mechanism of the low-temperature oxidation of carbon monoxide with oxygen on a PdCl<Subscript>2</Subscript>–CuCl<Subscript>2</Subscript>/γ-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalyst

A systematic study of the kinetics of the low-temperature oxidation of carbon monoxide with oxygen on a PdCl₂–CuCl₂/γ-Al₂O₃ supported catalyst was carried out over a wide range of the partial pressures of oxygen, water, and CO in order to test hypotheses on the reaction mechanism. It was shown that, as the temperature was increased from 20 to 38°C, rate of formation of CO₂ decreased and the apparent activation energy was about–40 kJ/mol. The hypotheses of different degrees of complexity concerning the reaction mechanism were formulated based on physicochemical data and a Langmuir–Hinshelwood model. Mechanisms in which carbon dioxide is formed on the interaction of the surface Pd(I) and Pd(II) complexes that include carbon monoxide and water with the surface complex of Cu(I) that coordinates oxygen were recognized as the most probable.     

多元醇法制备Cu2O/CNTs复合材料的研究

以Cu(CH₃COO)₂•H₂O和经硝酸处理的CNTs作为原料, 采用多元醇法成功合成了纳米氧化亚铜均布于碳纳米管表面的复合光催化剂. 用透射电镜(TEM), 高分辨透射电镜(HRTEM), X射线粉末衍射(XRD)对样品进行了表征, 测试结果表明大小为2～5 nm的氧化亚铜纳米颗粒均匀分散于碳纳米管的表面. 讨论了反应条件对Cu₂O在CNTs上负载效果的影响并就多元醇法合成Cu₂O/CNTs复合材料的反应机理作了初步探讨.     

Electrooxidation of Chlorophenols Catalyzed by Nickel Octadecylphthalocyanine Adsorbed on Single‐Walled Carbon Nanotubes

We described the synthesis of nickel octadecylphthalocyanine (NiPc(C₁₀H₂₁)₈), followed by its adsorption on single‐walled carbon nanotubes (SWCNT) to form SWCNT‐NiPc(C₁₀H₂₁)₈ conjugates. SWCNT‐NiPc(C₁₀H₂₁)₈ was used to modify a glassy carbon electrode (GCE) and for the electrooxidation of 4‐chlorophenol and 2,4‐dichlorophenol. The SWCNT and NiPc(C₁₀H₂₁)₈ have a synergistic effect on each other in terms of improving electrocatalysis for the detection of chlorophenols. The stability of the electrode improved in the presence of NiPc(C₁₀H₂₁)₈ or NiPc compared to the bare GCE. The presence of SWCNT improves the electrocatalytic behaviour of NiPc(C₁₀H₂₁)₈ but not of unsubstituted NiPc. All modified electrodes showed improved stability towards the detection of 2,4‐dichlorophenol. The best stability for 4‐CP detection was observed in the presence of SWCNT for NiPc(C₁₀H₂₁)₈.