疏水层析蛋白质动力学与平衡过程的考察

疏水层析是分离生物大分子的常用技术之一，但对疏水层析中蛋白质吸附动力学和平衡过程的研究并不多见．本文对蛋白质疏水吸附动力学和平衡过程作了基本假设，并用实验进行了验证。制备了两种不同丁基密度的疏水琼脂糖介质，用其吸附牛血清白蛋白(BSA)以验证对疏水吸附动力学与平衡过程作的假设，考察了盐浓度及配基密度对蛋白质疏水吸附的影响．还对三种疏水性不同的蛋白质：核糖核酸酶、卵清蛋白和牛血清白蛋白的混合体系进行了分离性能的研究，获得了满意的分离效果．实验表明，蛋白质在疏水介质上的吸附动力学和平衡过程与所作假设相符，在实验条件下等温吸附线符合Langmuir吸附等温方程：研制的丁基琼脂糖疏水介质具有优良的使用性能。     

硅胶自环己烷溶液中吸附苯甲酸和苯的计量置换吸附模型

在293~313 K温度范围, 研究了硅胶在环己烷溶液中对苯甲酸和苯的吸附. 发现苯甲酸能非常好地服从计量置换吸附模型(SDM-A). 在用SDM-A处理苯的吸附时, 出现折线形的吸附等温线, 折线的转折点正好是单分子层吸附与多分子层吸附的分界点. 基于SDM-A, 研究了吸附热力学, 建立了吸附热力学的计算公式. 发现在环己烷溶液中苯甲酸被硅胶吸附是自发的、放热的熵增大过程, 而苯被吸附是自发的放热的熵减少过程, 苯甲酸的吸附自由能大于苯, 而吸附焓小于苯, 这是因为苯甲酸有更大的亲吸附剂作用和疏溶剂作用的结果.     

SAPO-34上甲醇及二甲醚吸附等温线及吸附热测量与分析(英文)

在25,60和100°C下分别测定了甲醇及二甲醚在SAPO-34分子筛上的吸附等温线,同时用微量热法测定了微分吸附热与覆盖率的关系曲线(量热线),提出了吸附数据需要利用双吸附位Langmuir方程拟合,并获取了相应的吸附参数.对比测得的吸附等温线与量热线发现,在一定压力下,当甲醇及二甲醚在SAPO-34上达到一定吸附量后,随着吸附质分压增加,量热线快速下降,而吸附等温线显示出吸附量仍然继续增加.由此推断,在SAPO-34分子筛上存在两种吸附位——常规吸附位及弱吸附位,其中弱吸附位在高分压下继续吸附.如缺乏量热数据提供的常规吸附位饱和吸附量数据,对吸附等温线进行单吸附位拟合获取吸附参数极易导致错误结果,尤其是当吸附质分压较高时.建议采用双吸附位Langmuir方程,参照量热线提供的常规吸附位的饱和吸附量,通过拟合可以获得两种吸附位的吸附参数.     

壳聚糖插层蒙脱土复合材料吸附酸性染料的动力学和热力学研究

通过离子交换的方法将天然大分子壳聚糖引入蒙脱土的层间,利用XRD和TG对得到的复合材料进行表征。将该复合材料用于酸性黑10B的吸附,考查了pH值、染料起始浓度、吸附时间以及温度对吸附性能的影响。结果表明,吸附动力学实验数据符合准二级动力学模型。应用Langmuir和Freundlich两种模型描述吸附等温线,结果显示Langmuir模型的拟合效果更好。计算得到吸附过程的热力学参数△Go、△Ho和△So的值分别为-27.16kJ/mol(20℃)、-14.18kJ/mol和44.0J/mol.K,说明复合材料对酸性染料的吸附是一个自发进行的放热过程。     

超高交联树脂对壬基酚聚氧乙烯醚的吸附机理(英文)

研究了壬基酚聚氧乙烯醚(NPEO-10)在3种具有不同比表面积和孔径大小的超高交联树脂上的吸附行为与机理.3种超高交联树脂对壬基酚聚氧乙烯醚的吸附量受它们的比表面积和孔径大小以及溶液温度的影响.壬基酚聚氧乙烯醚在3种超高交联树脂上的吸附等温线可以用Langmuir和双Langmuir模型很好地拟合,而用Freundlich模型拟合则效果不好,但这些拟合曲线都具有相似的形状.热力学分析表明吸附过程主要表现为吸附质分子的疏水部分和吸附剂表面的作用以及吸附质分子在其表面形成胶束状的聚集体,即分散的、单层及双层聚集体的混合分布.吸附动力学曲线中的两个平台也证明了吸附过程存在单层和双层聚集体.脱附研究为实现超高交联树脂吸附分离水溶液中的壬基酚聚氧乙烯醚提供了合适的操作条件.     

胺甲基化聚丙烯酰胺阳离子交换剂的合成与表征

采用反相悬浮聚合法合成20%交联度的聚丙烯酰膀(Polyacrylamide,PAM)树脂,经过Mannich反应修饰(nacrylamide:nformaldehyde:ndimethylamine=1:1:1.2)得到高亲水性弱碱性阴离子交换剂氨甲基化聚丙烯酰胺(Aminomcthylated Polyacrylamide,APAM).随着修饰反应时间的增加,得到的APAM的弱碱交换量与蛋白质吸附量增加,在选定的实验条件下,确定Mannich反应时间以1h为宜,所得树脂对牛血清白蛋白吸附量达到433mg/g,过长的反应时间导致树脂结构有一定程度的破坏.树脂对蛋白质的吸附等温线符合Langmuir方程,实际分离牛血清白蛋白和血红蛋白效果较好,柱体积不随洗脱液中盐浓度的增加而变化.     

氨基双四唑型金属螯合磁性纳米粒子的制备及其对蛋白质的吸附性能

通过4步化学反应对磁性Fe3O4@Si02纳米粒子进行化学修饰,设计和制备了一种N,N’-二(5-四唑亚甲基)胺修饰的金属螯合磁性纳米粒子.用X射线光电子能谱(XPS)、Zeta电位对该新型吸附剂进行了表征.用静态吸附法研究了螯合Cu(Ⅱ)吸附剂对溶菌酶、细胞色素C和α-糜蛋白酶的吸附性能以及溶液pH值、盐浓度、蛋白初始浓度对吸附量的影响.结果表明,吸附剂对蛋白质的吸附主要通过金属配位机理进行,且符合Langmuir吸附模型,对溶菌酶、细胞色素C和α-糜蛋白酶的最大吸附量分别20.0、13.5和17.9 mg/g.此外,将螯合Cu(Ⅱ)吸附剂用于混合蛋白质样品的吸附,发现此吸附剂对混合蛋白质样品中的溶菌酶具有选择性吸附作用,说明此金属螯合吸附剂在蛋白质选择性分离富集中具有一定应用价值.     

吸附法和溶胶-凝胶法固定化醇脱氢酶比较研究

采用吸附法与溶胶-凝胶(sol-gel)包埋法固定化醇脱氢酶(ADH),对两种方法固定化的ADH的活性进行了比较.采用大孔硅胶为载体对ADH进行吸附,研究了吸附动力学和吸附平衡,得到了吸附动力学曲线和吸附等温线,ADH在硅胶上的吸附等温线可以用Langmuir方程拟合.并且考察了硅胶孔径对ADH吸附量的影响,发现大孔径的硅胶对ADH有着较大吸附量.同时采用sol-gel法对ADH进行包埋固定化.在PH 7.0、25℃下,对两种固定化酶催化甲醛转化为甲醇的反应活性进行比较.由实验测得的反应初速度及拟合得到的米氏常数表明吸附法固定化ADH表现出比sol-gel法固定化ADH高的催化活性.     

功能化的石墨烯和磁铁掺杂的还原氧化石墨烯对亚甲基蓝的吸附作用

用简单可行的方法合成了功能化的石墨烯(GNSPF6)和磁铁掺杂的还原氧化石墨烯(RGO-Fe3O4),并进一步研究了pH值、接触的时间和温度对它们吸附亚甲基蓝(MB)的影响.结果表明,随着pH值和温度的增加其吸附量也随之变大,从而说明该吸附过程是自发吸热的.因为GNSPF6的吸附过程只用了不到20min的时间,所以它的吸附是高效的.用经典的准一级反应、准二级反应和粒内扩散模型对其吸附过程进行动态分析,从结果可以发现,准二级动力学模型比准一级动力学模型更适用于描述吸附过程.采用传统的Langmuir,Freundlich和L-F吸附等温线模型来模拟分析数据,在20℃时,由Langmuir吸附等温线模型模拟分析得知GNSPF6和RGO-Fe3O4对MB的最大吸附量分别为374.4和118.4mg/g.     

N-乙烯吡咯烷酮/甲基丙烯酸-β-羟乙酯无规共聚物凝胶对蛋白质吸附机理的研究

用紫外分光光度法研究了牛血清白蛋白(BSA)在N-乙烯吡咯烷酮(NVP)/甲基丙烯酸-β-羟乙酯(HEMA)共聚物水凝胶上的吸附量.结果表明,BSA在凝胶上的吸附关系既可用Langmuir方程描述,又可用计量置换吸附Freundlich方程描述,且用Langmuir方程描述更为优越.研究了凝胶对BSA的吸附动力学行为,建立牛血清白蛋白的吸附动力学模型,发现用Bangharm方程对BSA吸附动力学曲线拟合程度较好,Bangharm方程可以较好地描述BSA在NVP/HEMA凝胶上的吸附动力学行为.     

奥美拉唑对映体在自制手性柱上吸附等温线的测定

采用吸附-脱附法研究了奥美拉唑对映体在自制的纤维素三苯基氨基甲酸酯涂敷型手性柱上的吸附性能,并用Langmuir方程拟合出吸附平衡方程.当样品浓度降低时,Langmuir方程退化为直线关系,直线斜率即为吸附平衡常数.这一吸附平衡常数与从脉冲色谱流出曲线求得的吸附平衡常数相等,表明吸附-脱附法测得的吸附平衡关系准确,Langmuir方程能描述这一吸附平衡关系.     

Isotherms for adsorption of cellobiohydrolase I and II fromtrichoderma reesei on microcrystalline cellulose

Adsorption to microcrystalline cellulose (Avicel) of pure cellobiohydrolase I and II (CBH I and CBH II) fromTrichoderma reesei has been studied. Adsorption isotherms of the enzymes were measured at 4‡C using CBH I and CBH II alone and in reconstituted equimolar mixtures. Several models (Langmuir, Freundlich, Temkin, Jovanovic) were tested to describe the experimental adsorption isotherms. The isotherms did not follow the basic (one site) Langmuir equation that has often been used to describe adsorption isotherms of cellulases; correlation coefficients (R²) were only 0.926 and 0.947, for CBH I and II, respectively. The experimental isotherms were best described by a model of Langmuir type with two adsorption sites and by a combined Langmuir-Freundlich model (analogous to the Hill equation); using these models the correlation coefficients were in most cases higher than 0.995. Apparent binding parameters derived from the two sites Langmuir model indicated stronger binding of CBH II compared to CBH I; the distribution coefficients were 20.7 and 3.7 L/g for the two enzymes, respectively. The binding capacity, on the other hand, was higher for CBH I, 1.0 Μmol (67 mg) per gram Avicel, compared to 0.57 Μmol/g (30 mg/g) for CBH II. The isotherms when analyzed with the combined Langmuir-Freundlich model indicated presence of unequal binding sites on cellulose and/or negative cooperativity in the binding of the enzyme molecules.     

Adsorption and desorption kinetics of benzene derivatives on mesoporous carbons

Adsorption and desorption of benzoic and salicylic acids and phenol from a series of synthesized mesoporous carbons is measured and analyzed. Equilibrium adsorption isotherms are best described by the Langmuir–Freundlich isotherm. Intraparticle diffusion and McKay’s pore diffusion models, as well as mixed 1,2-order (MOE), integrated Langmuir kinetic equation (IKL), Langmuir–Freundlich kinetic equation and recently derived fractal-like MOE (f-MOE) and IKL models were compared and used to analyze adsorption kinetic data. New generalization of Langmuir kinetics (gIKL), MOE and f-MOE were used to describe desorption kinetics. Analysis of adsorption and desorption half-times shows simple relation to the size of carbon pores.     

Nonlinear isotherm and kinetics of adsorption of copper from aqueous solutions on bentonite

Bentonite is one of the most significant of clay minerals that has been studied extensively due to its potential applications in removal of various environmental pollutants. This ability is related to its high ionic exchange capacity and high specific surface area. Copper is one of the important elements of non-ferrous metals found in industrial waste waters. In the present work, the removal of copper from aqueous solutions with Iranian bentonite (from Birjand area, southeastern Iran) used without any chemical pretreatment, was studied. The experimental results were fitted by adsorption isotherms equations with two or three parameters, which include Langmuir, Freundlich, Dubinin-Radushkevich (D-R), Redlich-Peterson, Khan, and Toth models. The best correlation coefficient (r²) is 0.9879 observed for Langmuir model, maximum adsorption capacity of bentonite was 55.71 mg/g. The first-order and pseudo-second-order kinetic equations were used to describe the kinetics of adsorption. The experimental data were well fitted by the pseudo-second-order kinetics.     

阴离子型有机化合物在LDHs上的动力学和热力学研究

本文考察水滑石焙烧产物MgAl-LDO吸附3种阴离子染料AcidRed88（AR88）、AcidOrange 3（AO3）、AcidViolet90（AV90）过程中的热力学和动力学机理,并在不同温度下探究该吸附过程的热力学参数。实验结果表明：MgAl-LDO对染料阴离子的吸附过程复合Langmuir吸附等温模型,且为自发、放热的过程。3种染料在MgAl-LDO上的吸附过程均符合准二级反应动力学模型,且该吸附过程是由MgAl-LDO与阴离子染料之间的反应速率控制而不是两者之间的扩散作用。计算所得的吉布斯自由能绝对值在7~15kJ·mol^-1,这主要是由染料阴离子与MgAl-LDHs层板的氢键作用产生,结合MaterialsStudio 5.5软件模拟染料分子在MgAl-LDHs上的排列分布,推测MgAl-LDO对阴离子染料的吸附机理是表面吸附（占优势）与层间插层的协同作用。     

阴离子型有机化合物在LDHs上的动力学和热力学研究

考察了水滑石焙烧产物MgAl-LDO吸附3种阴离子染料Acid Red 88(AR88)、Acid Orange 3(AO3)、Acid Violet 90(AV90)过程中的热力学和动力学机理,并在不同温度下探究该吸附过程的热力学参数。实验结果表明:MgAl-LDO对染料阴离子的吸附过程复合Langmuir吸附等温模型,且为自发、放热的过程。3种染料在MgAl-LDO上的吸附过程均符合准二级反应动力学模型,且该吸附过程是由MgAl-LDO与阴离子染料之间的反应速率控制而不是两者之间的扩散作用。计算所得的吉布斯自由能绝对值在7~15 kJ·mol-1,这主要是由染料阴离子与MgAl-LDHs层板的氢键作用产生,结合Materials Studio 5.5软件模拟染料分子在MgAl-LDHs上的排列分布,推测MgAl-LDO对阴离子染料的吸附机理是表面吸附(占优势)与层间插层的协同作用。     

Comparison of Adsorption Isotherms of Methylxanthines on C18 Column

A comparison of the adsorption isotherms of caffeine, theophylline and theobromine and the competitive adsorption of the three compounds on a C 18 column were investigated. The experimental parameters of the equilibrium isotherms were estimated by linear and nonlinear regression analyses. The linear equation as a function of the adsorption concentration of the single compound in its solution and the competitive adsorption of a single compound in a mixed solution were then determined. The adsorption equilibrium data were then correlated to the linear, Langmuir, Freundlich, Langmuir-Freundlich and stoichiometric displacement theory for adsorption(SDT-A) isotherm models. The mixed compounds of the three compounds were competitively adsorbed on the C 18 particles. The expression of stoichiometric displacement theory for adsorption was found to be more suitable for adsorption of methylxanthines on a C 18 column.     

自然水体生物膜吸附Co,Ni和Cu的特征研究

研究了在自然水体中培养的生物膜吸附Co,Ni和Cu等3种重金属的热力学和动力学特征,并对生物膜吸附各重金属的热力学数据进行了非线性拟合.结果表明,3种重金属的吸附过程均符合Langmuir吸附等温曲线.在溶液中重金属浓度<0.5μmol/L时,生物膜对3种重金属元素的吸附能力顺序是Co>Cu>Ni;在重金属浓度>0.5μmol/L时,顺序是Cu>Co>Ni.对动力学数据进行非线性拟合的结果表明,生物膜对Co,Ni和Cu的吸附均在数小时内达到平衡,吸附过程符合Langmuir等动力学曲线.     

Adsorption Isotherms of Quercetin and Catechin Compounds on Quercetin-MIP

A molecular imprinted polymer(MIP)was prepared with quercetin as the template and methacrylic acid(MAA)as the functional monomer.Acetonitrile and methanol were used as the porogen with ethylene glycol dimethacrylate(EGDMA)as the crosslinker and 2,2'-azobis(isobutyronitrile)(AIBN)as the initiator.The experimental parameters of the equilibrium isotherms were estimated via linear and nonlinear regression analyses.The linear equation as the functions of the adsorption concentration of the single compound in its solution and the competitive adsorption of the single compound in its mixed compounds solution was then expressed,and the adsorption equilibrium data were correlated to Langmuir and Freundlich isotherm models.The mixture compounds show competitive adsorption on the specific binding sites of quercetin-MIP.Furthermore,the competitive Langmuir isotherms were applied to the mixture compounds.The adsorption concentrations of quercetin,( )catechin( C),and(-)epicatechin(EC)on the quercetin molecular imprinted polymer were compared.The quercetin-imprinted polymer shows extraordinarily higher adsorption ability for quercetin than for the two catechin compounds that were also assessed.