树脂填充EVAL中空纤维膜吸附剂的吸附及脱附性能研究

以亲水性乙烯-乙烯醇共聚物(EVAL)为膜吸附剂基质材料,阳离子交换树脂D061为功能树脂,采用干-湿法纺丝技术,制备了树脂填充EVAL中空纤维膜吸附剂。实验采用连续循环膜过滤工艺,研究了这种吸附剂对目标蛋白(牛血清白蛋白-BSA)的吸附和脱附性能。考察了树脂填充量、缓冲溶液pH值等对蛋白质吸附和脱附性能的影响。实验结果表明,树脂填充EVAL中空纤维膜吸附剂对目标蛋白BSA具有较高的吸附容量和脱附率,随着树脂填充量的增加,膜吸附剂对BSA吸附容量增加,并且最大吸附容量在牛血清蛋白等电点(4.8～5.2)附近出现。当树脂填充量65%,缓冲溶液pH4.5时树脂填充EVAL中空纤维膜吸附剂对BSA的吸附容量可达到71.47mgBSA/g膜吸附剂。     

利用辅助识别聚合物链制备牛血清白蛋白分子印迹聚合物

论文提出了一种新的蛋白质分子印迹方法, 即以聚乙烯醇接枝聚合物作为辅助识别聚合物链(ARPCs), 以丙烯酰胺为单体, 在丙烯酸酯树脂载体表面进行聚合, 制备牛血清白蛋白分子印迹树脂. 实验使用2.00 mol•L⁻¹氯化钾(KC1)溶液除去模板蛋白质, 使用十二烷基磺酸钠-聚丙烯酰胺凝胶电泳(SDS-PAGE)检测吸附蛋白质, 并设计使用0.150, 0.500和2.00 mol•L⁻¹KC1溶液分别对吸附蛋白质进行梯度洗提. 电泳实验结果表明, 2.00 mol•L⁻¹KC1溶液洗脱的蛋白质是大孔树脂的吸附效应; 0.500 mol•L⁻¹KC1溶液洗脱掉的是印迹蛋白质. 引入ARPCs制得的分子印迹树脂, 用于混合蛋白质体系吸附时, 对模板蛋白质的吸附量为80~100μg•g⁻¹, 其特异性吸附能力较未引入ARPCs之前有明显提高.     

酚羟基修饰的超高交联聚苯乙烯树脂对苯酚吸附及脱附性能的研究

对超高交联聚苯乙烯树脂进行酚羟基修饰得到修饰后的超高交联聚苯乙烯树脂(JN-2),将该树脂与大孔吸附树脂(Amberlite XAD-4)和超高交联树脂(NDA-150)在水溶液中对苯酚进行吸附-脱附性能比较,经过酚羟基修饰的超高交联聚苯乙烯树脂(JN-2)对苯酚的吸附性能有所提高,同时脱附性能明显改善,该树脂可望在含酚废水治理中得到广泛应用.     

微波辅助合成聚酰胺-胺修饰硅胶及其对牛血清白蛋白的吸附性能研究

采用微波辅助合成法制备了聚酰胺-胺树枝状大分子修饰硅胶,并考察了其对牛血清白蛋白(BSA)的吸附性能。PAMAM修饰硅胶的合成条件通过元素分析进行考察,不同代数PAMAM修饰硅胶通过傅里叶变换红外光谱法表征。结果表明,在微波辅助下制备的PAMAM修饰硅胶的红外光谱图中出现酰胺的特征吸收峰与采用传统加热方法的文献报道一致,而采用微波辅助和传统加热方法的反应时间分别为40min和24h,由此说明微波辅助合成聚酰胺-胺树枝状大分子修饰硅胶是可行的。同时研究还发现聚酰胺-胺修饰硅胶对蛋白的吸附能力比未经修饰的硅胶强,而且蛋白的吸附量随着聚酰胺-胺代数的增加而增加。     

微纳米多孔不锈钢表面高效吸附活性生物大分子

不锈钢(AISI 316L)是目前在医药器械中应用最为广泛的商业化材料. 下一代的不锈钢智能材料将特殊功能的生物活性分子(或纳米粒子)修饰在金属表面以模拟组织功能、提高生物/细胞相容性, 这是目前材料科学研究的热点领域之一. 本文研究了具有微纳米多孔表面结构的316L 不锈钢对抗体和生物酶分子的吸附作用,并与这些生物分子在光滑表面以及镀金表面的吸附进行了比较. 研究发现不锈钢可通过简单的电化学腐蚀方法在表面产生微纳米多孔结构. 微纳米孔不锈钢表面可稳定地吸附抗体或辣根过氧化物酶分子, 其吸附量与喷镀金表面相当或更好. 用表面活性剂(10%牛血清白蛋白(BSA)或0.2% Tween-20)洗涤不能除去吸附的蛋白.用5% Tween-20 预处理金属表面, 则可减少一半的抗体吸附量; 但表面活性剂预处理对辣根过氧化物酶的吸附没有影响. 吸附蛋白质后的金属表面湿润度大大增加; 蛋白质修饰的微纳米孔不锈钢表面表现出了很好的亲水性(水接触角小于50°), 指示了很好的生物相容性. 而金属表面的湿润度则主要取决于蛋白质物种, 并与蛋白质的吸附量正相关. 吸附于不锈钢微纳米孔表面的抗体仍保持了良好的生物活性; 用此种方式制备的抗CD34抗体修饰的不锈钢血管支架可以高密度并高选择性地吸附其目标细胞(如KG-1细胞). 本文工作为未来制备新型的无高聚物涂层的不锈钢智能医学生物材料提供了基础.     

富羧类吸附树脂对水溶液中HIPI的吸附研究

以NDA99和NDA150树脂作为参照,通过等温吸附实验和吸附动力学实验探讨了修饰后的树脂对水溶液中5-对羟基苯基海因(HIPI)的吸附性能和机理.结果表明:羧基修饰的超高交联吸附树脂(FZH124)比NDA99和NDA150树脂对水溶液中HIPI具有更好的吸附效果,而且在303K时吸附效果最好.Langmuir和Freundlich方程均能较好拟合修饰树脂对HIPI的吸附等温线.HIPI在FZH124树脂上的动态吸附符合准一级动力学方程,303K时,树脂对HIPI的吸附速率最大,颗粒内扩散过程是该吸附过程的主要控制步骤.     

一种后交联大孔吸附树脂的合成及其对苯酚和维生素B_(12)吸附性能研究

工业二乙烯苯悬浮聚合制备的大孔树脂,在二氯乙烷溶剂中以无水三氯化铁为催化剂进行悬挂双键后交联反应,得到的后交联树脂的比表面积和孔容都有显著增加.低温氮气吸附/脱附等温线得到的孔径分布曲线证明初始共聚物PDT-55(polydivinylbenzene,toluene as porogen)和PDH-55(polydivinylbenzene,heptane andtoluene as porogen)经后交联反应,所形成的新孔以微孔为主.树脂对水溶液中苯酚和维生素B12(VB12)的静态吸附研究发现树脂经后交联后,对苯酚的吸附量有显著提高,但对VB12的吸附量增加不大,原因是分子尺寸较大的VB12无法进入由悬挂双键后交联反应所形成的微孔.树脂PDT-55pc对苯酚的吸附量大于商品树脂XAD-4;后交联前后树脂PDT-55、PDT-55pc(post-crosslinking of PDT-55)、PDH-55、PDH-55pc(post-crosslinking ofPDH-55)对VB12的吸附量均大于树脂XAD-4.在本研究的实验条件下,Langmiur和Freundlich吸附等温线方程能很好地拟合树脂对水溶液中苯酚和VB12的吸附,相关系数在0.99以上.静态吸附动力学实验结果表明后交联前后树脂对苯酚的吸附较VB12更容易达到吸附平衡.吸附动力学数据的拟合结果显示,McKay二级吸附动力学模型符合树脂对苯酚的吸附,而对VB12的吸附更符合Lagergren一级吸附动力学模型.     

化学修饰超高交联吸附树脂对水中四环素的吸附研究

本文采用偏苯三酸酐修饰的超高交联吸附树脂(TMAMR)和羟丙基纤维素修饰的超高交联吸附树脂(HPCMR)作为吸附剂,以NDA150树脂作对照,研究了3种树脂对水中四环素的吸附性能和吸附机理,同时考察了p H值和Na+浓度对TMAMR和HPCMR树脂吸附四环素的影响。结果表明,TMAMR和HPCMR树脂的比表面积较高,树脂表面修饰了大量的羟基,对四环素均具有较好的吸附性能。3种树脂对四环素的吸附量均随着温度的升高而增大,吸附过程中同时存在较强的物理吸附和化学吸附作用。Langmuir和Freundlich等温吸附方程均能够较好地拟合吸附等温线,吸附机理较复杂。吸附热力学结果表明,四环素在3种树脂上的吸附为自发的吸热过程,且吸附过程的熵增加。p H值对TMAMR和HPCMR树脂吸附四环素有较大的影响,在中性条件下,树脂对四环素的吸附量最大,在强酸和强碱条件下树脂的吸附量均较低。吸附液中加入无机盐后,发生盐析作用,导致TMAMR和HPCMR树脂对四环素的吸附量增大。     

牛血清白蛋白在NVP/HEMA无规共聚物水凝胶上的吸附研究

合成了不同含水量的N-乙烯吡咯烷酮(NVP)／甲基丙烯酸-β-羟乙酯(HEMA)共聚物水凝胶．研究了温度、pH值，蛋白质初浓度及离子强度等因素对牛血清白蛋白吸附性能的影响．采用紫外分光光度法测定BSA的吸附量．结果表明，蛋白质初浓度越高．温度越高，离子强度越大；蛋白质内部更多的疏水性氧基酸残基暴露于外部．吸附量增加：在等电点pH=4．7附近蛋白质沉积量最大．     

氨基膦酸树脂的合成及其对氟离子的吸附

本文以伯胺树脂、亚磷酸、甲醛为原料,通过Mannich反应合成了功能基为-CH_2NHCH_2P(OH)_2的氨基膦酸树脂。该树脂与Al~(3+)的络合物对F~-的吸附量最高可达9.297mg/ml。去除率为75％以上。     

A carbanion induced synthesis of highly congested pyrazole and imidazole containing heterocycles

An efficient approach to the synthesis of highly congested di, penta and hexacyclic pyrazoles as well as imidazole fragment containing novel heterocyclic molecule has been developed through a carbanion induced transformation of suitably functionalized 2H-pyran-2-ones, benzo[h]chromene and thiochromeno[4,3-b]pyrans. Due to the presence of fluorescence, we report their prime application metal sensor as off/on switching in ferric ions.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Selective synthesis of 4,5-dihydroimidazo- and imidazo[1,5-a]quinoxalines via modified Pictet–Spengler reaction

An efficient tandem approach for the selective synthesis of 4,5-dihydroimidazo[1,5-a]quinoxalines 6a–g and imidazo[1,5-a]quinoxalines 7a–h by the reaction of 2-imidazolyl anilines 4a–c with aryl aldehydes 5a–k under mild reaction conditions is described. Introduction of electron releasing alkyl groups in substrates 4a–b was found to be instrumental for the success of the reaction.     

Understanding the Diels-Alder reactivity of 1,2-azaborine analogues

The Diels-Alder reactivity of 1,2-heteroborines (H₄C₄B(H)X, X?=?NH, PH, AsH; O, S, Se) has been computationally explored by means of Density Functional Theory (DFT) calculations. The influence of the HB?=?X fragment on the reactivity of the system has been quantitatively analyzed in detail by means of the so-called Activation Strain Model (ASM) of reactivity. It is found that the interaction between these species and the dienophile is significantly stronger than that computed for their all-carbon isoelectronic counterpart, benzene. In addition, the strain energy plays a key role in the observed reactivity trends. The role of the aromaticity strength of these heteroarenes on the reactivity is also assessed.     

Synthesis of N-substituted carbazolones from α-iodo enaminones via Pd(0)-catalyzed intramolecular coupling under microwave irradiation

A variety of N-aryl and N-alkyl carbazolones were conveniently achieved in good to high yields via Pd₂(dba)₃-mediated intramolecular coupling of N-substituted α-iodo enaminones under microwave irradiation. The Pd(0)-catalyzed cyclization was found to proceed favorably with the more electron-deficient phenyl ring during the reactions involving unsymmetrical N,N-diaryl α-iodo enaminones. This unique property enables the construction of carbazolone skeleton containing nitro substituted benzenoid ring.     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of substituted 2,4,5,6-tetrahydrocyclopenta[c]pyrazoles and 2,4,5,6-tetrahydropyrrolo[3,4-c]pyrazoles by intramolecular nitrilimine cycloaddition

Both substituted 2,4,5,6-tetrahydrocyclopenta[c]pyrazoles and 2,4,5,6-tetrahydropyrrolo[3,4-c]pyrazoles have been synthesized by the 3+2 intramolecular dipolar cycloaddition of nitrilimines to alkynes. This cyclization has been extended to more versatile 3-bromo derivatives by the use of alkynylbromides as dipolarophiles.