微胶囊制备新方法——乳滴模板法

本文介绍一种新颖、灵活的微胶囊制备方法--乳滴模板法.胶体粒子在乳滴表面自组装形成有序的球面胶体壳,交联固定乳滴表面的胶体粒子制备新型的"胶体体(colloidosome)"微胶囊,即以胶体粒子为壳的微胶囊.乳滴模板法制备微胶囊的优点是方法简单,胶囊的尺寸、渗透性、机械强度容易调控.这种新型的微胶囊在功能食品、药物载体、生物医药,尤其是细胞移植等领域具有潜在的应用前景.     

碱式碳酸铜微球的表面改性和组装

报道了通过分散聚合反应在碱式碳酸铜微球表面锚接聚苯乙烯纳米粒子, 以调节其亲水/亲油性的方法. 结果表明, 锚接的聚苯乙烯纳米粒子尺寸愈大, 所得的改性碱式碳酸铜微球疏水性愈强. 用对油和水润湿性适中的改性碱式碳酸铜微球为乳化剂, 能够制备出稳定的油包水型Pickering乳液. 改性碱式碳酸铜微球组装在Pickering乳液的分散相液滴表面, 形成一个固体壳层. 将Pickering 乳液的分散相水核凝胶化, 合成出分级结构琼脂糖凝胶微球.     

Pickering乳液聚合制备核-壳结构PS-SiO2复合微球

用二氯二甲基硅烷对纳米SiO2粒子进行疏水改性,当其表面Zeta电位由-54.8 mV变成-25.8 mV时,SiO2粒子就能在苯乙烯-水界面自组装,形成稳定的Pickering乳液,即以胶体粒子为乳化剂的乳液.利用Pickering乳液聚合制备了以聚苯乙烯(PS)为核、纳米SiO2为壳的PS-SiO2复合微球.用FT-IR、XPS、SEM、偏光显微镜等对复合微球进行了表征.结果表明:复合微球由聚苯乙烯和纳米二氧化硅粒子组成,二氧化硅粒子以单层、六方密排的方式分布在聚苯乙烯微球表面.     

制备方法对模板法制备SiO_2中空微球形貌的影响

模板法是制备无机中空微球的重要方法之一.首先通过苯乙烯和甲基丙烯酸的无皂乳液聚合法制得表面含羧基、粒径为360nm的单分散聚苯乙烯(PSt)乳胶粒,并以此为模板,分别采用表面改性-前驱体水解法(PHC)和SiO2纳米颗粒层层自组装法(LBL),制备出了不同壳层厚度的PSt/SiO2核壳结构复合微球,然后经500℃煅烧4h,得到SiO2中空微球.利用透射电镜和扫描电镜对微球结构形态进行了表征.研究表明,首先利用γ-氨丙基三乙氧基硅烷(KH-550)对PSt模板微球进行表面改性、然后再在乙醇-水混合介质中进行原硅酸乙酯(TEOS)水解与缩合反应的PHC法,是制备PSt/SiO2核壳结构复合微球的简便方法,复合微球经煅烧可制得表面均匀、结构致密、壳层厚度和形貌可控的SiO2中空微球;而LBL法制备PSt/SiO2核壳结构复合微球的工艺复杂,煅烧后所得SiO2中空微球结构疏松,易于破碎.     

双重Pickering乳液模板法制备无机-有机复合空心微球

以疏水性ZnO粒子和亲水性Fe_3O_4粒子稳定的W/O/W型双重Pickering乳液为模板,制备了具有空心结构的无机-有机复合微球.采用X射线衍射(XRD)仪、扫描电子显微镜(SEM)、X射线能谱仪(EDS)、傅里叶变换红外光谱(FTIR)仪及光学显微镜等对制备的无机粒子、乳液和复合材料进行了表征.结果表明,制备了ZnO和Fe_3O_42种无机粒子,油酸能够对Zn O进行有效的疏水改性,改性后的接触角为84.3°.制备的双重Pickering乳液稳定性好、粒径分布较宽(50～200μm),以该双重乳液为模板制备的无机-有机复合材料为空心球形结构,粒径范围为100～200μm.     

空心球壳型V2O5的制备研究

无机空心微球含可容纳大量客体的中空部分,具有比表面积大、密度小、表面渗透能力强、稳定性好等特点,在化学、生物、材料科学和光电领域均有重要的应用,如控制释放胶囊(药物、颜料、化妆品、油墨)、催化剂及催化剂载体、分离材料、声学隔音材料以及电子学元件等。[1-3]空心球壳材料的制备方法通常有喷雾干燥法,乳液法[4],模板合成法[5]。近年来以胶体粒子为模板合成空心材料引起了人们的高度重视,其中聚苯乙烯微球(PSt)由于其形貌规整,粒径均一而被广泛用作形成空心结构的有机模板[6]。通过对锂离子电池正极材料的广泛研究,发现空心球壳型…     

Pickering乳液模板法制备有机/无机杂化微胶囊

以亲水性的二氧化硅(SiO2)纳米粒子稳定的水包油Pickering乳液为模板,利用聚氧化丙烯二醇和二苯基甲烷二异氰酸酯预聚物(PPG-TDI)与二乙烯三胺(DETA)在油水界面的聚合反应制备了聚脲(PU)包裹苯乙酸乙酯(EPA)-异佛尔酮二异氰酸酯(IPDI)有机/无机杂化微胶囊.通过控制不同油水比得到不同粒径大小的微胶囊,粒径分布为20~90μm.热重分析表明EPA-IPDI的装载量达到53 wt%.扫描电子显微镜图片可以看出,微胶囊表面光滑,呈规整球形,厚度均一,约2μm.     

二苯基二甲氧基硅烷单体制备空心微胶囊的模板合成方法研究

制备了直径在700～1500 nm范围内的空心聚硅氧烷微球. 在O/W型聚二苯基硅氧烷微乳模板核上, 加入一定比例的二苯基二甲氧基硅烷(D型官能团)和甲基三甲氧基硅烷(T型官能团)的有机硅单体, 使之围绕在模板核表面聚合交联形成核壳结构的聚硅氧烷微胶囊, 利用合适溶剂溶解透析的方法去除模板核得到空心微胶囊. 通过TEM和AFM测定考察, 讨论了体系的各反应条件对空心微球的形态结构和大小分布的影响.     

以胶体粒子为模板制备核壳纳米复合粒子*

核壳纳米复合粒子具有许多不同于单组分胶体粒子的独特的光、电、磁、催化等物理与化学性质,是构筑新型功能复合材料的重要组元,在光子带隙材料、微波吸收材料、电磁流变液、催化剂和生物等领域有重要应用.本文从控制核壳复合粒子的微观结构及壳层均匀性与厚度的角度,详细评述了目前以胶体粒子为模板制备粒径从纳米到微米尺度的核壳复合粒子的方法.指出利用胶体粒子模板表面与壳层物质或其前驱物间的特殊相互作用(包括静电和化学相互作用),是完善现有制备方法和发展新方法来制备具有设定组成、结构和性能的核壳复合粒子的关键,同时也是将来的粒子表面纳米工程和获取有序的、先进纳米复合材料的主要方向。     

纳米结构型PMAA/CdS复合微球的微凝胶模板法制备研究

以微凝胶为模板,利用微凝胶三维网络结构对无机沉积反应的限域和导向作用,制备了具有核-壳结构的聚甲基丙烯酸/硫化镉(PMAA/CdS)有机/无机复合微球材料.复合微球的制备包含两个基本步骤首先,以反相乳液聚合法得到包含Cd(Ac)2的聚甲基丙烯酸微凝胶;然后,在搅拌过程中向反应体系中缓慢通人H2S气体,使镉离子沉积为CdS,经洗涤处理后得到PMAA/CdS复合微球.SEM观察表明,复合微球表面呈现均一的微纳米结构,这种结构可因微球制备条件的不同而不同.而且,超声处理可使微球表面趋于光滑.X射线衍射分析表明复合微球中CdS处于晶态,具有立方结构.此外,复合微球因CdS的存在而具有光致发光特性.     

纳米玉米醇溶蛋白微球稳定的O/W型Pickering乳液

利用相分离工艺制备玉米醇溶蛋白(zein)纳米微球,微球粒径可控制在40 nm左右;经旋转蒸发制得zein溶胶体系,zein溶胶具有明显的丁达尔现象,静置数月不聚沉,Zeta电位法测得zein微球在pH值为4.0时分散性能最佳。 以纳米zein微球为固相稳定剂制备O/W型Pickering乳液,考察了zein胶体加入量、油水体积比等因素对乳液稳定性的影响。 实验结果表明,zein胶体加入量的质量分数控制为0.4%,高油水体积比将有利于Pickering乳液的长时间稳定。 基于zein分子的两亲结构和界面组装特点,提出了zein微球稳定Pickering乳液的作用机制。     

紫外光引发Pickering乳液聚合制备中空复合微球的研究

用光引发剂2-羟基-4-(2-羟乙氧基)-2-甲基苯丙酮(IHT-PI 659)对纳米SiO₂表面进行接枝使之兼具两亲性及光引发特性|以该功能性纳米SiO₂为稳定剂构筑O/W(水包油)型Pickering乳液|用紫外光引发处于内油相的甲基丙烯酸甲酯单体聚合, 制备出具有中空结构的SiO₂/PMMA复合微球, 采用傅里叶变换红外光谱(FTIR)、热失重分析仪(TGA)、透射电镜(TEM)及扫描电子显微镜(SEM)对复合微球进行了表征, 并提出了紫外光引发Pickering乳液聚合制备中空复合微球的机理.     

PMMA colloid particles armored by clay layers with PDMAEMA polymer brushes

Poly[2‐(dimethylamino) ethyl methacrylate] (PDMAEMA) brushes on the surfaces of clay layers were prepared by in situ free‐radical polymerization. Poly (methyl methacrylate) (PMMA) colloid particles stabilized and initiated by clay layers with PDMAEMA polymer brushes were prepared by Pickering emulsion polymerization. Transmission electron microscopy was used to characterize the structure and morphology of the colloid particles. The X‐ray diffraction (XRD) results indicated that the intercalated structures of the clay layers were almost destroyed in Pickering emulsion polymerization, and clay layers with exfoliated structures were created. The surface of the colloid particles was analyzed by using X‐ray photoelectron spectroscopy (XPS). The XPS results provide direct evidence that the clay layers with PDMAEMA chains cover the PMMA colloid particles. © 2008 Wiley Periodicals, Inc. JPolym Sci Part A: Polym Chem 46: 2632–2639, 2008     

Hollow microspheres with covalent‐bonded colloidal and polymeric shell by Pickering emulsion polymerization

Hollow microspheres with SiO₂/polymer binary shell were fabricated from Pickering emulsion stabilized solely by methacryloxypropyltrimethoxysilane‐modified SiO₂ particles, and were characterized by optical microscopy, scanning electron microscopy, Fourier transformation infrared spectrum, thermogravimetric analysis (TGA), and energy dispersive X‐ray spectroscopy. The microspheres were templated by the Pickering droplets and the inner structure was affect by the proportion of crosslinking reagent. TGA result indicated that 60.3% of polymer in the shell was connected with SiO₂ by covalent bond which was formed by copolymerization of styrene and the reactive C?C group on SiO₂ stabilizer. Copyright © 2011 John Wiley & Sons, Ltd.     

Pickering乳液模板法制备Janus粒子

本文以SiO₂粒子稳定的水包油(O/W)型Pickering乳液作为模板, 在乳液连续相进行SI-ATRP, 将聚合物刷接枝到SiO₂粒子外半表面, 破乳得到半修饰的Janus粒子.     

CO2-triggered switchable Pickering emulsion stabilized by guanidine-functionalized silica particles

The guanidine group-modified silica particles were used as emulsifier to obtain a CO₂-responsive Pickering emulsion. To compare the wettability effect of the particles on the stability of the emulsion, both guanidine and alkyl chain were attached on the surface of silica particles. The influences of tension, particles concentration, oil-water fraction, NaCl concentration, and CO₂ on Pickering emulsion properties were investigated. Although the particles did not decrease the surface and interfacial tensions of the air/oil-water interfaces, they attached on the oil–water interfaces and stabilized the emulsions at room temperature for at least 4 weeks. Addition of salt increased the emulsion stability and induced phase inversion at high salt concentration. The stabilization–destabilization cycles of the emulsion could be successively controlled by alternative CO₂/heating triggers due to the protonation-deprotonation of guanidine groups on the particle surfaces.     

Pickering乳液的制备和应用研究进展

Pickering乳液是一种由固体粒子代替传统有机表面活性剂稳定乳液体系的新型乳液。与传统乳液相比,Pickering乳液具有强界面稳定性、减少泡沫出现、可再生、低毒、低成本等优势,在化妆品、食品、制药、石油和废水处理等行业具有广阔的应用前景,受到越来越多研究者们的关注。本文综述了近年来Pickering乳液的研究进展,先介绍Pickering乳液相对于表面活性剂乳液的特色与优势,然后介绍Pickering乳液的制备研究进展,最后介绍Pickering乳液的应用研究进展。     

A novel formulation of the pickering emulsion stabilized with silica nanoparticles and its thermal resistance at high temperatures

Stabilization of emulsions with solid particles can be used in several fields of oil and gas industry because of their higher stability. Solid particles should be amphiphilic to be able to make Pickering emulsions. This goal is achieved by using surfactants at low concentrations. Oil-in-water (o/w) emulsions are usually stabilized by surfactant but show poor thermal stability. This problem limits their applications at high-temperature conditions. In this study, a novel formulation for o/w stabilized emulsion by using silica nanoparticles and the nonionic surfactant is investigated for the formulation of thermally stable Pickering emulsion. The experiments performed on this Pickering emulsion formula showed higher thermal stability than conventional emulsions. The optimum wettability was found for DME surfactant and silica nanoparticles, consequently, in that region; Pickering emulsion showed the highest stability. Rheological changes were evaluated versus variation in surfactant concentration, silica concentration and pH. Scanning electron microscopy images approved the existence of a rigid layer of nanoparticle at the oil-water interface. Finally, the results show this type of emulsion remains stable in harsh conditions and allows the system to reach its optimum rheology without adding any further additives.     

Interaction of antigen and antibody on core-shell polymeric microspheres

Monodispersed microspheres with polystyrene as the core and poly(acrylamide-co-N-acryloxysuccinirnide) as the shell were synthesized by a two-step surfactant-free emulsion copolymerization.The core-shell morphology of the microspheres was shown by scanning electron microscopy and transmission electron microscopy.Rabbit immunoglobulin G (as antigen) was covalently coupled onto the microspheres by the reaction between succinimide-activated ester groups on the shell of the microspheres and amino groups of the antigen molecules.The size of particles was characterized by dynamic light scattering technique and was found to vary upon bioconjugation and interaction with proteins.The binding process was shown to be specific to goat anti-rabbit immunoglobulin G(as antibody) and reversible upon the addition of free antigen into the system.     

Synthesis of ZnO/polystyrene composites particles by Pickering emulsion polymerization

ZnO/polystyrene composite particles were synthesized by Pickering emulsion polymerization. ZnO nanoparticles were first prepared by reaction of zinc acetate and sodium hydroxide in ethanol medium. Then different amount of styrene monomer was emulsified in water in the presence of ZnO nanoparticles either by mechanical stirring or by sonication, followed by polymerization of styrene. Two kinds of initiators were used to start the polymerization, azobisisobutyronitrile (AIBN) and potassium persulfate (KPS). The X-ray diffraction pattern verified the crystal structure of ZnO and FT-IR spectra evidenced the existence of ZnO and polystyrene (PS) in ZnO/polystyrene composite particles. Different morphologies were observed for the composite particles when using different initiators. From TEM photographs, AIBN-initiated system produced mainly core-shell composite particles with PS as core and ZnO as shell, while KPS-initiated system showed both composite particles and pure PS particles. Two schemes of reaction mechanism were proposed to explain the morphologies accordingly. Both systems of composite particles showed good pH adjusting ability.