铝掺杂及钨酸锂表面包覆双效提升富锂锰基正极材料的循环稳定性

采用溶胶-凝胶法合成Al掺杂富锂锰基Li_1.2Mn_0.54-xAl_xNi_0.13Co_0.13O₂（x=0、0.03）锂离子电池正极材料,之后采用一步液相法制备Li₂WO₄包覆层,系统地研究了Al掺杂和Li₂WO₄包覆双效改性对富锂锰基正极材料电化学性能的影响.结果表明,Al掺杂后明显提升富锂锰基正极材料的循环稳定性,包覆层Li₂WO₄明显改善其倍率性能和放电平台电压衰减问题.Li₂WO₄包覆量为5% Li_1.2Mn_0.51Al_0.03Ni_0.13Co_0.13O₂正极材料在2.0~4.8 V充放电电压区间及1000 mA·g^-1电流密度下比容量仍高达110 mAh·g^-1左右,同时在100 mA·g^-1的电流密度下循环300次容量保持率为78%,而且循环过程中放电平台电压衰减也明显减缓.该工作为解决锂离子电池富锂锰基正极材料循环稳定性和平台电压衰减提供了新的思路.     

锂离子电池正极材料Li1.2Mn0.54Ni0.13Co0.13O2研究进展

富锂锰基正极材料Li_1.2Mn_0.54Ni_0.13Co_0.13O₂因具有超过250 mA·h·g^-1的可逆比容量和高工作电压(>3.5 V. Li/Li⁺)以及经济成本低的特点，在便携式电子设备中发挥着重要的作用，也被认为是下一代混合动力汽车(HEV)和电动汽车(EV)的理想动力源，是一种有前途的正极材料。由于富锂锰基正极材料存在低倍率容量、电压衰减严重、初始容量损失大的问题，因此提高电池的容量和寿命是目前研究的重点。为此综述了锂离子电池富锂锰基正极材料Li_1.2Mn_0.54Ni_0.13Co_0.13O₂的储锂机理、制备方法以及改性研究。     

锂离子电池富锂锰基正极材料的研究进展

随着新能源如电动汽车、储能电站的蓬勃发展,人们对下一代高性能锂离子电池的能量密度、功率密度和循环寿命提出了更高的要求. 而富锂锰基正极材料xLi₂MnO₃·(1-x)LiMO₂（0 < x < 1,M = Mn、Co、Ni…）具有可逆比容量高（240 ~ 280 mAh·g^-1,2.0 ~ 4.8 V）、电化学性能较佳、成本较低等优点,已吸引了研究者的关注,有望成为下一代锂离子电池用正极材料. 本实验室采用固相法和溶胶-凝胶法制备不同的富锂锰基正极材料,其中,溶胶-凝胶法制得的Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂电极首周期放电比容量277.3 mAh·g^-1,50周期循环后容量272.8 mAh·g^-1,容量保持率98.4%. 本文重点结合本实验室的研究工作,对新型富锂锰基正极材料xLi₂MnO₃·(1-x)LiMO₂的结构、合成、电化学性能改性和充放电机理等进行总结与评述.     

富锂锰基正极材料的表面改性研究进展

随着电动汽车和储能电站等电力设备的快速发展,对高能量密度的锂离子电池的需求日益增加.高比容量（>250 mAh·g^-1）的富锂锰基正极材料,有望成为锂离子电池实现高比能量（>350 Wh·kg^-1）的关键正极材料.富锂锰基正极材料的Li₂MnO₃相和晶格氧参与电化学反应使其拥有了高容量,但这也导致表面结构和成分容易发生变化,进而造成富锂锰基正极材料存在着诸如首次库伦效率低、倍率性能差和循环后电压和容量衰减严重等问题.因此,本文综述了富锂锰基正极材料的表面包覆、表面掺杂和表面化学处理三种表面改性方法,并进一步讨论了三种表面改性方法对材料性能提升的机制机理和优缺点.在此基础上,介绍了近些年基于多方法的表面联合改性工作.通过对富锂锰基正极材料进行表面联合改性,不仅可以改善其结构稳定性和抑制电极/电解液界面副反应,而且可以缓解其在循环过程中不断发生的结构转变和晶格氧的析出问题.最后,对富锂锰基正极材料表面改性研究方向进行了总结和展望.     

原位包覆纳米碳提升钴锰氧化物材料储锌性能

钴锰氧化物（CMO）具有安全无毒、价格便宜、活性位点多等优点,是极具潜力的锌离子电池正极材料.目前,充放电过程中电极材料溶解造成的结构坍塌成为限制其发展的瓶颈问题.本工作提出了一种原位碳包覆的方法来缓解CMO的溶解问题,在提高材料容量的基础上成功地延长了其循环寿命.通过简单的一步水热方法,成功制备了纳米碳（nC）包覆的钴锰氧化物（CMO@C）材料,X射线衍射（XRD）、X射线光电子能谱（XPS）、拉曼光谱（Raman）等表征证明,nC包覆层的引入并没有改变CMO材料的基本组分结构.而且,相较于CMO,CMO@C的电荷转移阻力更小,离子扩散更快,表现出更优异的电化学性能.在0.5 A·g^-1的电流密度下,CMO@C显示出271.9 mAh·g^-1的比容量,且经过1000圈循环后,材料的比容量没有发生衰减,性能大大优于CMO对比样品（103.7 mAh·g^-1;130圈失效）.由此可见,纳米碳包覆层可同时提升CMO的储锌容量和循环寿命.本工作为双金属氧化物正极材料的优化改性提供了新的策略.     

纳米Al2O3包覆富锂锰基正极材料Li1.2Ni0.13Co0.13Mn0.54O2的性能研究

采用纳米三氧化二铝(Al₂O₃)对富锂锰基正极材料Li_1.2Ni_0.13Co_0.13Mn_0.54O₂进行表面均匀包覆, 并考察了最优纳米Al₂O₃包覆量下材料的电化学性能. 扫描电子显微镜(SEM)和透射电子显微镜(TEM)显示了纳米Al₂O₃对富锂锰基正极材料表面均匀包覆, X射线衍射分析(XRD)结果表明包覆后富锂材料依然具有良好的层状结构. 恒流充/放电循环测试发现, 包覆后的Li_1.2Ni_0.13Co_0.13Mn_0.54O₂材料的首次放电比容量为249.7 mA·h/g, 循环100次后的容量保持率为89.5%, 与未包覆的Li_1.2Ni_0.13Co_0.13Mn_0.54O₂材料相比, 容量保持率提升约13%. 循环伏安(CV)和电化学阻抗(EIS)测试结果表明, 纳米Al₂O₃包覆可有效抑制材料极化, 降低界面阻抗和电荷转移阻抗, 进而提升富锂锰基正极材料的电化学性能.     

碳包覆碳酸钴锂离子电池负极材料的制备及电化学性能

以葡萄糖作为碳源,通过简单的水热反应获得菱形碳包覆碳酸钴(CoCO₃/C)复合材料,并研究了其作为锂离子电池负极材料的电化学性能.晶型和表面形貌通过X射线衍射(XRD)、扫描电子显微镜(SEM)和透射电子显微镜(TEM)进行表征,用热重-差热分析法(TG-DTA)来测试CoCO₃/C材料中碳的含量,用拉曼光谱分析无定型碳的存在. Barrett-Joyner-Halenda (BJH)则用来分析材料的孔径分布情况.实验表明,碳包覆不仅在CoCO₃颗粒表面包覆了一层无定性碳,使得CoCO₃材料在充放电过程中保持结构的稳定性,也形成了一些大约30 nm左右的介孔,这种孔的存在有助于电解液中离子的传输,从而提高材料的电化学性能.电极材料在0.90C(1.00C = 450 mAh•g^-1)倍率下进行循环测试, 500次后的容量仍保持在539 mAh•g^-1,显示出了较好的循环性能.当增加到3.00C倍率时CoCO₃/C容量为130 mAh•g^-1,再恢复到0.15C倍率时容量依然能够达到770 mAh•g^-1,表现出了CoCO₃/C具有良好的稳定性.     

电压敏感性聚三苯胺修饰隔膜用于锂硫电池过充保护

本文以三苯胺为原料,通过化学氧化法制备了具有电压敏感性的聚三苯胺(PTPAn)并将其成功应用到锂硫电池隔膜上。电导率测试结果表明,PTPAn/聚丙烯(PP)隔膜的离子电导率达1.56 mS·cm^-1;循环伏安(CV)测试结果表明,PTPAn/PP隔膜在3.5–4.2 V内具有氧化还原峰。在0.1C倍率下,采用PTPAn/PP隔膜和空白PP隔膜的锂硫电池在经200周循环后,放电比容量分别为424.8和407.2 mAh·g^-1,库伦效率分别为99.38%和98.59%,倍率测试表明(0.1C、0.2C、0.5C、1C),采用PTPAn/PP隔膜的锂硫电池在不同倍率下放电比容量均高于采用空白PP隔膜的锂硫电池。与此同时,对采用PTPAn/PP隔膜的锂硫电池进行过充实验,在第4周过充时,充电比容量为843.1 mAh·g^-1,放电比容量为839.8 mAh·g^-1;第10周过充时,充电比容量为690.2 mAh·g^-1,放电比容量为669.2 mAh·g^-1。第16周过充时,电池的充电比容量为538.7 mAh·g^-1,放电比容量为512.9 mAh·g^-1。倍率过充测试表明,经过不同倍率过充实验后,采用PTPAn/PP隔膜的锂硫电池仍能正常工作,在1C倍率下过充,电池电压稳定保持在3.9 V,充电比容量为349.8 mAh·g^-1,放电比容量为328.7 mAh·g^-1。     

芘基共轭微孔聚合物用于锂离子电池电极材料性能研究

共轭微孔聚合物由于其高的比表面积、优良的物理化学稳定性以及沿分子链延伸的共轭结构等特点,使其在锂离子电池电极材料方面具有巨大的应用前景.本工作以四溴芘和对苯二硼酸为构建单元,通过Suzuki偶联反应合成了具有高比表面积的芘基共轭微孔聚合物PyDB,并研究了其作为锂离子电池电极材料的电化学性能.当PyDB用作锂离子电池正极材料时,在50 mA·g^-1的电流密度下,放电容量达到163 mAh·g^-1,即使在3000 mA·g^-1的电流密度下仍具有62 mAh·g^-1的可逆容量,在100 mA·g^-1的电流密度下循环300次仍具有167 mAh·g^-1的容量.当该聚合物用作负极材料时,在50 mA·g^-1电流密度下的放电容量达到495 mAh·g^-1,在200 mA·g^-1的电流密度下循环300次,仍具有245 mAh·g^-1的容量.PyDB优异的电化学性能主要归因于其延伸的共轭结构和高比表面积的多孔结构,大的共轭结构有利于分子链的掺杂反应和电子传导,高比表面积的多孔结构有利于提供大量的活性位点并促进离子的迁移.     

分级结构氮掺杂碳纳米笼:高倍率长寿命可充电镁电池正极材料

可充电镁电池成本低、安全性好,是非常有前景的下一代二次电池,其关键之一是开发高性能的正极材料.本工作首次利用分级结构氮掺杂碳纳米笼（hNCNC）作为可充电镁电池的正极材料,展现出高放电比容量（71 mAh·g^-1@100 mA·g^-1）、优异的倍率性能（60 mAh·g^-1@2000 mA·g^-1）和长循环稳定性（1000圈容量保留率83%@1000 mA·g^-1）.hNCNC呈现电容行为主导的储镁机制,理论研究表明镁离子主要吸附在微孔边缘的碳原子、吡啶氮或吡咯氮等活性位点上.其优异储镁性能可归因于：（1） hNCNC的大比表面积（1590 m²·g^-1）、丰富微孔缺陷和高吡啶/吡咯氮含量（4.49 at.%）有效提升了储镁容量;（2） hNCNC的高导电性、多级孔道结构及N掺杂导致的高浸润性有利于电荷传输,降低了电池的等效串联电阻,从而改善了倍率性能;（3） hNCNC的稳定碳骨架结构及其表面吸附储镁机制使其具有优异的长循环稳定性.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

A carbanion induced synthesis of highly congested pyrazole and imidazole containing heterocycles

An efficient approach to the synthesis of highly congested di, penta and hexacyclic pyrazoles as well as imidazole fragment containing novel heterocyclic molecule has been developed through a carbanion induced transformation of suitably functionalized 2H-pyran-2-ones, benzo[h]chromene and thiochromeno[4,3-b]pyrans. Due to the presence of fluorescence, we report their prime application metal sensor as off/on switching in ferric ions.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

正丁胺对激光染料荧光谱影响的研究

用正丁胺作为碳源,采用射频辉光放电制备碳膜,选用激光染料R6G和聚乙二醇混合液作为蒸气源,采用单源热蒸发,在蒸发室与染料同时沉积得到混合膜,用拉曼光谱和红外光谱分析了碳膜的结构和键合方式,分析表明:碳膜中存在胺基团和氢原子.混合膜的荧光谱测量结果表明,认为正丁胺对染料荧光谱的影响是因为胺基和氢原子的存在.     

Selective synthesis of 4,5-dihydroimidazo- and imidazo[1,5-a]quinoxalines via modified Pictet–Spengler reaction

An efficient tandem approach for the selective synthesis of 4,5-dihydroimidazo[1,5-a]quinoxalines 6a–g and imidazo[1,5-a]quinoxalines 7a–h by the reaction of 2-imidazolyl anilines 4a–c with aryl aldehydes 5a–k under mild reaction conditions is described. Introduction of electron releasing alkyl groups in substrates 4a–b was found to be instrumental for the success of the reaction.     

Understanding the Diels-Alder reactivity of 1,2-azaborine analogues

The Diels-Alder reactivity of 1,2-heteroborines (H₄C₄B(H)X, X?=?NH, PH, AsH; O, S, Se) has been computationally explored by means of Density Functional Theory (DFT) calculations. The influence of the HB?=?X fragment on the reactivity of the system has been quantitatively analyzed in detail by means of the so-called Activation Strain Model (ASM) of reactivity. It is found that the interaction between these species and the dienophile is significantly stronger than that computed for their all-carbon isoelectronic counterpart, benzene. In addition, the strain energy plays a key role in the observed reactivity trends. The role of the aromaticity strength of these heteroarenes on the reactivity is also assessed.