蒸馏沉淀聚合法制备窄分散聚二乙烯基苯-co-丙烯腈功能聚合物微球

采用蒸馏沉淀聚合法,利用过氧化苯甲酰(BPO)为引发剂,在不加任何稳定剂和不搅拌的情况下,丙烯腈(AN)和二乙烯基苯(DVB)为共聚单体制备了不同交联度的微米和亚微米窄分散聚合物微球,考查了共聚单体对球体的影响,并用扫描电镜(SEM)和红外光谱对微球进行了表征.     

沉淀聚合法制备单分散聚(4-乙烯基吡啶-co-二乙烯基苯/三羟甲基丙烷三甲基丙烯酸酯)聚合物微球

以4-乙烯基吡啶(4-VP)为功能单体、二乙烯基苯(DVB)和三羟甲基丙烷三甲基丙烯酸酯(TRIM)为混合交联剂,偶氮二异丁腈(AIBN)为引发剂,乙腈为反应介质,采用沉淀聚合法制备单分散聚合物微球.考察了共聚单体、溶剂、引发剂等聚合条件对聚合物微球粒径、分散性以及产率的影响.并用扫描电镜(SEM)、激光粒度分析仪、热重分析仪和红外光谱对微球进行了表征.结果表明,聚合物微球的表面形貌和产率可通过改变溶剂体积、单体/交联剂摩尔比和引发剂浓度等因素进行控制.降低乙腈溶液体积、增加DVB摩尔比例及交联剂摩尔比、可增加聚合物粒径及粒度分布均匀性,而聚合物产率随溶剂体积和DVB摩尔比增大而减小,随交联剂摩尔比和引发剂浓度的增加而增加.在最优条件下,即DVB和TRIM两者摩尔比4∶1,单体/交联剂摩尔比1∶5,乙腈用量为5.6 m L(单体和交联剂占介质体积的7%),引发剂浓度为2 wt%~6 wt%(占总反应单体的量)时,可获得形貌规则、产率较高的单分散poly(4-VP-co-DVB/TRIM)微球,微球平均粒径约4.02μm,粒径分布指数(U)为1.013.此外,热重分析结果显示,聚合微球于350℃时开始分解,600℃时失重率达84.9%.     

沉淀聚合法Poly(DVB-co-EGDMA-co-MAA)功能聚合物微球的制备及表征

采用二乙烯基苯-55(DVB-55)和乙二醇二甲基丙烯酸酯(EGDMA)作为混合交联剂,乙腈为溶剂,偶氮二异丁腈(AIBN)为引发剂,以甲基丙烯酸为功能单体采用沉淀聚合法合成了单分散或窄分散的、表面具有羧基的交联聚合物微球,所得微球的粒径变化范围为0.6～3.8μm.通过调节交联剂DVB-55和EGDMA的投料比,可以对微球的粒径、粒径分布、产率、热稳定性以及表面官能团含量进行有效控制.文中对混合交联剂DVB-55与EGDMA比例的改变对微球的粒径、粒径分布以及产率的影响机理给出了理论解释;对DVB和EGDMA的兼容性研究表明,制备的三元聚合物微球的核拥有比投料比稍多的DVB单元,而微球的外层则以在预聚混合物中占更大比例的交联剂为主.     

蒸馏沉淀聚合过程中交联度对单分散聚合物微球形成的影响

以苯乙烯为单体、二乙烯基苯(DVB)为交联剂,过氧化二苯甲酰(BPO)为引发剂研究了蒸馏沉淀聚合法制备聚合物微球过程中交联单体二乙烯苯的用量对单分散聚合物微球成球的影响.结果表明,增加二乙烯基苯的比例,即提高交联度有利于形成单分散的聚合物微球.     

两亲磁性高分子微球的合成与表征

在Fe3O4磁流体存在下 ,通过苯乙烯与聚氧乙烯大分子单体 (MPEO)分散共聚制备两亲磁性高分子微球 .研究了聚氧乙烯大分子单体对微球粒径的影响 .用扫描电子显微镜 (SEM)、原子力显微镜 (AFM)表征了磁性微球的粒径、表面形貌以及表面粗糙度 ,用傅立叶红外光谱 (FTIR)鉴定了共聚物的结构 .随着聚合物中聚氧乙烯大分子单体含量的增加 ,微球表面的粗糙度增加 ,通过改变共聚物中MPEO的含量 ,可以得到含有 0 4～ 3 5mg g羟值的两亲磁性高分子微球     

核-壳型白藜芦醇分子印迹微球研制及应用

以表面修饰乙烯基团的SiO2微球为基体,白藜芦醇为模板分子,丙烯酰胺(AA)为功能单体,乙二醇二甲基丙烯酸酯(EGDMA)为交联剂,采用表面印迹技术制备核-壳型白藜芦醇印迹微球。采用红外光谱(IR)、扫描电子显微镜(SEM)对该分子印迹微球进行表征,结果表明,SiO2表面成功接枝一层厚度为200nm的印迹聚合物,该印迹微球颗粒分散均匀。采用高效液相色谱技术对印迹微球的吸附性进行研究表明,此印迹微球具有良好的识别性能,利用Scatchard模型分析得出印迹微球的最大吸附量分别为Qmax1=9.087mg/g和Qmax2=13.80mg/g。此印迹微球成功用于分离虎杖提取液中白藜芦醇。     

热敏性聚(N-乙烯基异丁酰胺)接枝高分子微球的合成

用自由基聚合和端基反应法合成了大分子单体聚 (N 乙烯基异丁酰胺 ) (PNVIBA) ,将其与苯乙烯在乙醇 水的混合溶剂中进行分散共聚 ,得到了PNVIBA接枝聚苯乙烯 (PNVIBA g PSt)高分子微球 .用GPC、激光光散射和电子显微镜等对聚合物的分子量和微球直径及形态进行了表征 .研究结果表明 ,大分子单体PNVIBA和PNVIBA g PSt高分子微球具有明显的热敏性 ,并且发现PNVIBA g PSt微球直径和形态可通过改变反应条件加以控制 ,得到了一种新形态的亚微米级高分子微球     

三羟甲基丙烷三丙烯酸酯-甲基丙烯酸甲酯沉淀聚合制备单分散聚合物微球

以三羟甲基丙烷三丙烯酸酯(TMPTA)为交联剂,甲基丙烯酸甲酯(MMA)为共聚单体,偶氮二异丁腈为自由基引发剂,以乙醇或乙醇-水混合物作溶剂,在2 wt%的单体浓度下通过沉淀聚合制备了交联聚合物微球.探究了聚合时间、混合溶剂的含水量以及交联剂TMPTA用量对聚合过程及聚合产物的影响.结果表明,增加TMPTA用量可提高单体转化率和微球产率;所得微球的粒径则随着TMPTA用量的增加而减小.TMPTA用量占单体总量40 wt%至80 wt%,反应时间不少于6 h时可制得高度单分散聚合物微球,产率达到80%以上.在反应介质中加入水可明显提高单体转化率和微球产率,当混合溶剂中水的体积分数为35%时,仍可制得高度单分散聚合物微球,产率可达94%;但当混合溶剂中水的体积分数达40 vol%时,所得微球的多分散系数增大.     

种子聚合制备表面磺酸基功能化聚苯乙烯微球

首先采用分散聚合法制备得到单分散的粒径约1.4～2.7 μm的聚苯乙烯(PS)种子微球,并研究了控制微球粒径及其分布的工艺参数.然后采用种子聚合法,使用苯乙烯磺酸钠(NaSS)作为具有磺酸基的功能单体与苯乙烯(St)单体进行共聚.通过扫描电子显微镜(SEM)和X-射线光电子能谱(XPS)对最终微球的表面形貌和组成成分进行表征,结果表明:成功获得了表面磺酸基功能化的聚苯乙烯微球;苯乙烯磺酸钠与苯乙烯单体共聚的最佳摩尔比为1:3.     

阻抗蛋白质吸附载体微球的制备与性能研究

聚合条件对制备功能化微球起到至关重要的作用。在本文中,通过功能单体、烯丙基聚氧乙烯醚(APEG)和苯乙烯的分散共聚制备了一种阻抗蛋白质吸附的功能化微球;然后,通过红外光谱(FT-IR)、动态光散射(DLS)和扫描电镜(SEM)等手段分析这些功能微球的粒径、表面形态和性能;最后通过牛血清蛋白(BSA)吸附实验评价其阻抗吸附性能。实验结果表明：APEG兼具功能单体和稳定剂的功能,在合适的条件下,可以得到良好单分散性的微球。此外,每克聚(苯乙烯-烯丙基聚氧乙烯醚)(P(St-co-APEG))微球的BSA吸附量为0.66 mg,而每克聚(苯乙烯-甲基丙烯酸缩水甘油酯)(P(St-co-GMA))微球的BSA吸附量为4.8 mg。总之,通过分散共聚制备了一种阻抗蛋白质吸附的微球。     

Preparation of narrow or monodisperse poly(ethyleneglycol dimethacrylate) microspheres by distillation-precipitation polymerization

Highly crosslinked narrow or monodisperse poly(ethyleneglycol dimethacryltae) (polyEGDMA) microspheres were prepared by distillation-precipitation polymerization in neat acetonitrile with 2,2′-azobis(2-methyl propinitrile) (AIBN) as an initiator. The polymer microspheres with clean surfaces due to the absence of any added stabilizer in the reaction system were formed simultaneously through a precipitation manner during the distillation of acetonitrile off the reaction system. The effects of the solvent, initiator concentration, monomer concentration and comonomer (divinylbenzene, DVB) fraction on the formation of the microspheres were investigated. Narrow- or monodisperse particles with spherical shape and smooth surface were obtained with diameters between 1.18 and 2.50 μm with monomer loading lower than 3.13 vol%. The surfaces of the microspheres became rougher, some elliptic particles and doublet or triplet appeared with the increase of monomer concentration (as high as 3.75 vol%). The yield of polymer microspheres was increased from 31% to 75% with the increase of EGDMA fraction from 0 to 100% when EGDMA was copolymerized with DVB. The resulting polymer microspheres were characterized with scanning electron microscope (SEM) and Fourier transform-IR spectra.     

Synthesis of monodisperse anionic submicron polystyrene particles by stabilizer-free dispersion polymerization in alcoholic media

In this work, monodisperse polystyrene (PS) particles were synthesized in ethanol/water medium using sodium salt of styrene sulfonic acid and 2,2′-azobis(isobutyronitrile) as ionic comonomer and nonionic initiator, respectively. The polymerization was carried out at low agitation speed, and no stabilizer (or surfactant) was added to the polymerization medium. This polymerization system (stabilizer-free dispersion polymerization) was initiated as a homogeneous solution of monomer, comonomer, medium, and initiator. With the production of free radicals, polymerization developed into a heterogeneous system. The effect of various polymerization conditions on the size and size distribution of the obtained particles was evaluated. The experimental results showed that with an increase in ethanol content, the size of the particles increased while no significant change was observed in particle size distribution. Furthermore, with increasing ionic comonomer content, the size of the particles decreased and their size distribution became broader. Moreover, it was observed that addition of an electrolyte to the polymerization medium also increased the particles’ size and broadened their size distribution. It is noteworthy to point out that the coagulation occurred in higher amounts of electrolyte. Finally, it is concluded that the polar component of Hansen solubility parameter of the polymerization medium affects the particle size and particle size distribution greatly.     

Dispersion copolymerization of styrene and other vinyl monomers in polar solvents

Dispersion polymerization is a very attractive method for preparing micrometer‐size monodisperse polymer particles. The applications of microspheres have been greatly expanded by the use of copolymers. Here, the dispersion copolymerization of styrene and seven other vinyl monomers was carried out in polar solvents. The effect of the different comonomers on the particle size was systematically investigated. The particle size first decreased and then increased with an increasing fraction of acrylamide in the monomer feed, and at a higher fraction of such a comonomer, only a gel‐like polymer was obtained. The particle size also increased with the increase in the contents of the hydrophilic comonomers in the monomer mixtures, and the copolymer molecular weight decreased meanwhile. Although the amount of the hydrophobic comonomer in the monomer mixture changed, the particle size was hardly affected. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 555–561, 2001     

Preparation of monodisperse poly(St‐co‐PETEA) microspheres by precipitation polymerization using ethanol as solvent

Precipitation polymerization of styrene (St) was carried out with pentaerythritol tetraacrylate (PETEA) to produce monodisperse crosslinked microspheres. A much safer ethanol replaced acetonitrile as a solvent in precipitation polymerization of monodisperse crosslinked poly(St‐co‐PETEA) microspheres. Monodisperse crosslinked microspheres with high monomer conversion were achieved within 4 hr. Uniform and well‐separated monodisperse were obtained in ethanol when PETEA concentration varied from 30 vol% to 90 vol% and the particle diameter decreased from 0.75 to 0.58 µm. The particle yield increased from 36.51 to 64.38% by increase in the initiator loading from 1 to 8 wt%. No coagulum occurred between particles when the polymerization time varied from 2 to 10 hr. Copyright © 2010 John Wiley & Sons, Ltd.     

Efficient synthesis of monodisperse,highly crosslinked,and “living” functional polymer microspheres by the ambient temperature iniferter‐induced “living” radical precipitation polymerization

The facile and efficient one‐pot synthesis of monodisperse, highly crosslinked, and “living” functional copolymer microspheres by the ambient temperature iniferter‐induced “living” radical precipitation polymerization (ILRPP) is described for the first time. The simple introduction of iniferter‐induced “living” radical polymerization (ILRP) mechanism into precipitation polymerization system, together with the use of ethanol solvent, allows the direct generation of such uniform functional copolymer microspheres. The polymerization parameters (including monomer loading, iniferter concentration, molar ratio of crosslinker to monovinyl comonomer, and polymerization time and scale) showed much influence on the morphologies of the resulting copolymer microspheres, thus permitting the convenient tailoring of the particle sizes by easily tuning the reaction conditions. In particular, monodisperse poly(4‐vinylpyridine‐co‐ethylene glycol dimethacrylate) microspheres were prepared by the ambient temperature ILRPP even at a high monomer loading of 18 vol %. The general applicability of the ambient temperature ILRPP was confirmed by the preparation of uniform copolymer microspheres with incorporated glycidyl methacrylate. Moreover, the “livingness” of the resulting polymer microspheres was verified by their direct grafting of hydrophilic polymer brushes via surface‐initiated ILRP. Furthermore, a “grafting from” particle growth mechanism was proposed for ILRPP, which is considerably different from the “grafting to” particle growth mechanism in the traditional precipitation polymerization. © 2013 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Synthesis of large-sized monodisperse polystyrene microspheres by dispersion polymerization with dropwise monomer feeding procedure

Highly monodisperse polystyrene (PS) microspheres in the size range of 3.75–7.09 μm were synthesized by dispersion polymerization with dropwise monomer feeding procedure. The morphology, size, and particle size distribution (PSD) of the PS microspheres obtained by different monomer feeding modes, including batch polymerization and various feeding rates, were investigated. The PSD of particles showed a close dependence on feeding rate. The PS microspheres with low coefficient of variation (CV) values all less than 4.8% obtained by the optimum feeding rates revealed better uniformity than those by batch polymerization (CV values all more than 8.2%). According to the time courses of monomer conversion and particle numbers, the effects of monomer feeding modes on the polymerization reaction of the large-sized PS microspheres were clarified. It is found that the dropwise monomer feeding procedure is promising for the synthesis of large-sized monodisperse PS particles in 3.75–7.09 μm.     

分散共聚法制备窄分布P(St-co-nBA)微球

用分散共聚法制得窄分布苯乙烯(St)和丙烯酸正丁酯(nBA)的共聚物微球.采用1H-NMR、DSC、FTIR、SEM、LS等对共聚物的结构、形态、性能进行表征,考察了初始单体配比、温度、稳定剂浓度、分散介质极性、引发剂对微球粒径、粒径分布及转化率的影响.实验结果表明,初始单体比nBA/St增大,微球粒径增大,分布变宽,...