Dynamic mechanical properties of homogeneous copolymers of ethylene and 1-alkenes

The dynamic mechanical properties of homogeneous copolymers of ethylene with 1-butene, 1-octene, and 1-octadecene prepared by means of a vanadium-based catalyst system have been determined. The 1-butene copolymers show α′ and α transitions in the 20–60°C temperature range, whereas the 1-octene and 1-octadecene copolymers show single α transitions. The intensity of the β transition increases with comonomer content in 1-butene and 1-octene copolymers and also with the amount of interfacial material present. In ethylene-1-octadecene copolymers, this intensity is comparatively low, even though there is about 20% interfacial material present. The implications of these results with regard to the nature of interfacial material are discussed.     

PVT properties of polyethylene copolymer melts

PVT properties of four polyethylene random copolymers (ethylene-propylene, ethylene-1-butene, ethylene-1-hexene, and ethylene-1-octene) and linear polyethylene were measured at temperatures from 313 to 493 K and pressures up to 200 MPa. Dependence of properties such as specific volume, thermal expansion coefficient, isothermal compressibility, and characteristic parameter of equations of state on the length of the polymer branched chains were examined. It was found that the length of the branched chain did not affect the thermal expansion coefficient and isothermal compressibility. The specific volume of copolymers having longer branched chains were slightly larger than those copolymers with short branched chains.     

15个乙烯—乙烯基化合物共聚物的取代基参数

本文应用取代基参数（ＳＣＳ）方法处理了１５个ＥＶ共聚物的＾１３ＣＮＭＲ谱，它们是：（１）乙烯α－烯烃共聚物，即乙烯－丙烯共聚物，乙烯－丁烯－１共聚物，乙烯４－甲基－１－戊烯共聚物，乙烯－己烯－１共聚物和乙烯－辛烯－１共聚物；（２）乙烯－含氧乙烯共聚物，即乙烯－甲基丙烯酸Ｎ，Ｎ－二甲基胺乙酯共聚物，乙烯－丙烯酸甲酯共聚物，乙烯－丙烯酸共聚物，乙烯－乙酸乙烯酯，乙烯－乙烯醇，乙烯－一氧化碳共聚物（ＥＣ     

The influence of side branches on the structure of crystalline phase in ethylene-1-alkene copolymers

The influence of side branches on the unit cell dimensions in ethylene-1-alkene copolymers was investigated both at room temperature as well as during heating of the samples up to melting. Time resolved X-ray diffraction investigations revealed that in the case of ethylene-1-octene copolymers with low and moderate comonomer content, the transversal expansion of the unit cell occurs due to the limited thickness of lamellae, however the samples with higher comonomer content (above 5 mol %) exhibit distinctly larger expansion resulting from the stresses imparted on the basal surfaces of crystals by the excluded branches. At high temperatures, independently on the thermal expansion, an additional increase of the unit cell volume occurs, caused probably by a penetration of the end-parts of side branches, residing near the crystals surface, into the surface cells. Similar phenomenon is observed for ethylene-1-butene copolymer. On contrary, the ratio of the average unit cell volume in ethylene-1-propene copolymer to the unit cell volume in linear polyethylene at the same temperature, decreases starting from about 50 °C. Such a behavior is a new confirmation of a partial inclusion of methyl branches into the crystalline phase. Most probably, when the temperature increases, the volume of included branch becomes a decreasing fraction of the thermally expanding unit cell volume.     

Thermal properties of ethylene/long chain α-olefin copolymers produced by metallocenes

Metallocene type copolymers of ethylene with the α-olefins 1-octene, 1-tetradecene and 1-octadecene were characterized by dynamic scanning calorimeter (DSC) and by dynamic mechanical analysis (DMA). At a similar comonomer content above 3 mol%, the higher α-olefins gave lower melting points, crystallinities and densities than 1-octene. In DSC a separation technique sorting the crystalline sequence lengths of the polymer into groups was applied, and DSC index, DI, which gave a semiquantitative idea of the chemical homogeneity of the comonomer compositional distributions. By DMA the storage modulus as an indicator of stiffness and loss modulus and loss tangent as a measure of the effect of branching on the β relaxations were studied. The DMA measurements showed the loss modulus maximum to be a more sensitive value than the loss tangent maximum for the characterization of the comonomer distribution. The intensity of the β transition of 1-octadecene did not increase with increasing branching in contrast to the situation for 1-octene and 1-tetradecene copolymers.     

TiCl_4/MgCl_2催化丙烯/1-辛烯共聚合研究

本文用TiCl_4/MgCl_2-Al(i-Bu)_3催化剂进行丙烯/1-辛烯共聚合,研究发现引入少量共聚单体1-辛烯时,能提高丙烯的聚合活性。30℃时,测得共聚合竟聚率为r_丙=5.63,r_辛=0.32。共聚物的结晶度和己烷不溶物含量随其1-辛烯含量的增加而迅速下降。X射线衍射及~(13)C-NMR测定结果表明,共聚物的己烷可溶部分为非结晶的无规共聚物,己烷不溶部分是具有镶嵌着半个1-辛烯单体单元的长嵌段聚丙烯链结构的结晶性共聚物。     

A fully integrated high-throughput screening methodology for the discovery of new polyolefin catalysts: discovery of a new class of high temperature single-site group (IV) copolymerization catalysts

For the first time, new catalysts for olefin polymerization have been discovered through the application of fully integrated high-throughput primary and secondary screening techniques supported by rapid polymer characterization methods. Microscale 1-octene primary screening polymerization experiments combining arrays of ligands with reactive metal complexes M(CH(2)Ph)(4) (M = Zr, Hf) and multiple activation conditions represent a new high-throughput technique for discovering novel group (IV) polymerization catalysts. The primary screening methods described here have been validated using a commercially relevant polyolefin catalyst, and implemented rapidly to discover the new amide-ether based hafnium catalyst [eta(2)-(N,O)[bond](2-MeO[bond]C(6)H(4))(2,4,6-Me(3)C(6)H(2))N]Hf(CH(2)Ph)(3) (1), which is capable of polymerizing 1-octene to high conversion. The molecular structure of 1 has been determined by X-ray diffraction. Larger scale secondary screening experiments performed on a focused 96-member amine-ether library demonstrated the versatile high temperature ethylene-1-octene copolymerization capabilities of this catalyst class, and led to significant performance improvements over the initial primary screening discovery. Conventional one gallon batch reactor copolymerizations performed using selected amide-ether hafnium compounds confirmed the performance features of this new catalyst class, serving to fully validate the experimental results from the high-throughput approaches described herein.     

The influence of comonomer on ethylene/α-olefin copolymers prepared using [bis(N-(3-tert butylsalicylidene)anilinato)] titanium (IV) dichloride complex

We describe the synthesis of [bis(N-(3-tert-butylsalicylidene)anilinato)] titanium (IV) dichloride (Ti-FI complex) and examine the effects of comonomer (feed concentration and type) on its catalytic performance and properties of the resulting polymers. Ethylene/1-hexene and ethylene/1-octene copolymers were prepared through copolymerization using Ti-FI catalyst, activated by MAO cocatalyst at 323 K and 50 psi ethylene pressure at various initial comonomer concentrations. The obtained copolymers were characterized by DSC, GPC and 13C-NMR. The results indicate that Ti-FI complex performs as a high potential catalyst, as evidenced by high activity and high molecular weight and uniform molecular weight distribution of its products. Nevertheless, the bulky structure of FI catalyst seems to hinder the insertion of α-olefin comonomer, contributing to the pretty low comonomer incorporation into the polymer chain. The catalytic activity was enhanced with the comonomer feed concentration, but the molecular weight and melting temperature decreased. By comparison both sets of catalytic systems, namely ethylene/1-hexene and ethylene/1-octene copolymerization, the first one afforded better activity by reason of easier insertion of short chain comonomer. Although 1-hexene copolymers also exhibited higher molecular weight than 1-octene, no significant difference in both melting temperature and crystallinity can be noticed between these comonomers.     

Monomer-isomerization polymerization. XX. Monomer-isomerization polymerization of 2-, 3-, and 4-octenes with Ziegler–Natta catalyst

A study of the monomer isomerization polymerization of 2-, 3-, and 4-octenes has been made with TiCl₃–(C₂H₅)₃Al catalyst at 80°C in comparison with the ordinary polymerization of 1-octene. It was found that all these octenes underwent monomer-isomerization polymerization to give high-molecular-weight homopolymer consisting exclusively of the 1-octene unit. The addition of an isomerization catalyst such as nickel acetylacetonate accelerated this polymerization. The rates of polymerization were found to decrease in the following order: 1-octene > 2-octene > 3-octene > 4-octene. These results indicate that the isomerization proceeded by a stepwise double-bond migration. It was also found that the monomer-isomerization copolymerization of 2-octene and 2-butene occurred under similar conditions and produced copolymers of both 1-olefin units.     

Microstructure of vinyl acetate–butyl acrylate copolymers studied by 13C-NMR spectroscopy: Influence of emulsion polymerization process

The compositions and sequence distributions of vinyl acetate–butyl acrylate copolymers obtained with batch and semicontinuous emulsion polymerizations have been studied by ¹H and ¹³C NMR. The batch process gives heterogeneous copolymers while with the semicontinuous one the sequence distribution is statistical. These differences in sequence distributions have been related to the physical properties of the copolymers.     

Crystallinities of copolymers of ethylene and 1-alkenes

Random copolymers of ethylene with 1-butene, 1-octene, and 1-octadecene have been prepared using a homogeneous vanadium-based catalyst system. Comonomer contents determined by ¹³C-NMR analysis of polymer solutions are in the range 1–10 mol%. Crystallinities were estimated by means of density measurements, x-ray diffraction, differential scanning calorimetry, laser Raman spectroscopy, and CPMAS ¹³C-NMR spectroscopy. The results are compared with those obtained for heterogeneous copolymers of ethylene containing 1–4 mol% 1-butene. As the comonomer content is increased, the crystallinity decreases. The dimension perpendicular to the 110 plane in orthorhombic crystallites decreases linearly with crystallinity. This decrease in crystallite size is accompanied by an increase in the size of the orthorhombic unit cell. For copolymers containing large amounts of 1-octene and 1-octadecene, a second crystalline form appears. Differences in estimates of crystallinity are discussed in terms of looser packing in highly branched copolymers and the extent to which the second crystalline form participates in the phase structure.     

Simultaneous Deconvolution of Molecular Weight Distribution and Chemical Composition Distribution of Ethylene/1-Olefin Copolymers Synthesized with Multiple-Site-Type Catalytic Systems

Summary: Ethylene/1-olefin copolymers synthesized with multiple-site-type catalytic systems typically exhibit broad molecular weight distribution (MWD) and chemical composition distribution (CCD). These microstrucral characteristics can be described by the presence of several active site types, each of which produces chains with distinct chain microstructures. In this work, a new approach to identify the number of active site types and chain microstructures produced on each active site type was developed based on simultaneous deconvolution of the bivariate MWD/CCD information. Chain microstructures produced on each active site type are assumed to follow Stockmayer's bivariate distribution. The proposed approach was validated with simulated data of model ethylene/1-butene and ethylene/1-octene copolymers.     

Copolymerization of propylene with 1-octene initiated by highly efficient isospecific metallocene catalytic systems

The copolymerization of propylene with 1-octene in liquid propylene is carried out in the presence of a highly active homogeneous ansa-m etallocene catalyst with the C ₂-symmetry rac-Me₂Si(4-Ph-2- MeInd)₂ZrCl₂ activated by methyl aluminoxane and in the presence of ansa- metallocene C₄H₆Si(2-Et4- PhInd)₂ZrCl₂ (rac: meso = 2:1) supported on silica gel treated with methylaluminoxane. In the case of the heterogenized metallocene, (iso-C ₄ H ₉ )₃Al is used as a cocatalyst. The copolymers of propylene and 1-octene containing up to 24 and 9.3 mol% units of the second comonomer are prepared with the homogeneous and heterogenized systems, respectively. The copolymerization of propylene with 1-octene in liquid propylene shows the azeotropic (ideal) character, and the distribution of comonomer units in the copolymers is close to statistical. The modification of PP with even small amounts of 1-octene affects the regularity of polymer chains, molecular-mass characteristics of the copolymers, their melting temperature, and the degree of crystallinity and makes it possible to vary their rigidity and elasticity in a wide range. The character of changes in thermal and mechanical properties is almost the same for the copolymers synthesized with homogeneous and heterogenized catalysts.     

Structure and Properties of Ethene Copolymers Synthesized by Metallocene Catalysts

Abstract

The microstructure of ethylene copolymers based on 1-hexene, 1-octene, and norbornene as comonomers was studied and related to its melting, crystallization, and glass transition behavior as well as to tensile strength.     

COPOLYMERIZATION OF 1-OCTENE WITH STYRENE BY RARE EARTH COORDINATION CATALYSTS

The copolymerization of l-octene with styrene catalyzed by rare earth coordination catalysts has been studied for the first time. Some features and kinetic behavior are described. The overall activation energy of the copolymerization was 22.2 KJ/mol and the copolymerization rate could be expressed as R_p=K_p [Nd] [M]~2. (=1.68×10~(-3) L~2/mol~2. S, 50℃, [Oct]/[St]=1). The catalytic activity of various rare earth elements in Ln (naph)_3 for the copolymerization was compared and shows the following sequence: Dy, Y, Yb>Ho>Sm, Gd, Nd>Pr>Ce>La>Tm. Both monomers of l-octene and styrene in the copolymerization by Nd (naph)_3-AlEt_3 have the tendency of constant proportion copolymerization. The structure of the copolymers was studied by ~1H-NMR.     

Structure formation of random isotactic copolymers of propylene and 1-hexene or 1-octene at rapid cooling

The effect of variation the cooling rate in a wide range between 10^?2 and 10³ K s^?1 on solidification the relaxed melt of random isotactic copolymers of propylene with low amount of 1-hexene or 1-octene has been studied. Emphasis has been placed on the structure formation at rapid cooling and an evaluation of the conditions required to permit crystallization, mesophase formation, or suppression of any ordering. The presence of low amount of either 1-hexene or 1-octene co-units in the propylene chain decreases drastically the critical cooling rate required for suppression of crystallization from about 150–200 K s^?1 in the homopolymer to about only 10 K s^?1 in the copolymers; increasing the cooling rate beyond these limits allowed mesophase formation or even generation of fully amorphous samples. The study of the kinetics of formation of specific structures is completed by a complementary analysis of the X-ray structure, morphology and superstructure of the ordered phase. The hindrance of non-isothermal crystallization and mesophase formation of random copolymers of propylene with 1-hexene or 1-octene is compared with that in propylene–1-butene copolymers; addition of only 2–3 mol% 1-hexene or 1-octene into the propylene chain leads to even larger hindrance of the ordering process than the addition of more than 10 mol% 1-butene.     

The effect of supramolecular structure on deformation and relaxation transitions in ethylene-1-hexene copolymers crystallized from solution

Structure and mechanical properties of three samples based on ethylene-1-hexene copolymers prepared by crystallization from decalin solutions were studied. The rate of decrease in the true yield stress was shown to depend on temperature. This behavior was assumed to be due to the involvement in deformation of the “intermediate phase” that is located at the lamellar surface between the crystalline and amorphous phases.     

Melting behavior of polyethylene/α‐olefin copolymers: Narrow composition distribution copolymers and fractions from Ziegler–Natta and single‐site catalyst products

The melting temperature and heat of fusion were measured for an extensive series of compositionally uniform copolymers of ethylene with butene‐1, hexene‐1, and octene‐1. Fractions and whole polymers that exhibited minimal interchain compositional heterogeneity were from commercial copolymers made with either Ziegler–Natta (ZN) or single‐site metallocene catalysts. The present results do not support recent claims that ZN and corresponding metallocene catalyst copolymers melt at significantly different temperatures, nor the implication that comonomer incorporation is “blocky” in ZN copolymers. In five of the six comonomer/catalyst systems the dependencies of the melting temperature on comonomer type and amount were scarcely distinguishable. This common behavior is the same as that for a model random copolymer, so we conclude that most ethylene/α‐olefin copolymers have random distributions of ethylene sequences. The exception in the present study is a metallocene ethylene/butene‐1 copolymer that melts at lower temperatures and apparently has perceptibly alternating sequence distributions. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3416–3427, 2004     

全氟磺酰氟树脂热裂解的研究

全氟磺酰氟树脂是四氟乙烯和全氟3,6-二氧杂、4-甲基、7-辛烯磺酰氟(1)的共聚物(2):     

Stabilisation of metallocene ethylene-1-octene copolymers during multiple extrusions

The melt stabilising efficiency of antioxidants with different structures based on hindered phenols, phosphite esters, phosphonite and a lactone was examined during multi-pass extrusions at 265 °C in three metallocene ethylene-1-octene copolymers (m-LLDPE) having different extent of short chain branching (SCB) and one Zeigler copolymer (z-LLDPE) containing the same level of SCB corresponding to one of the m-LLDPE polymers. The effect of the different antioxidants, when used separately and in combination, was investigated by characterising the changes in the polymer's rheological behaviour, colour formation and structural changes based on unsaturated groups and carbonyl content during five multi-pass extrusions. The results showed that all stabilisation systems examined offered higher efficiency in the metallocene polymers compared to the Zeigler. The effect of the extent of SCB in the metallocene polymers on the stabilising efficacy of the antioxidant systems was also examined, and it was shown that it had a significant effect, with both single and combinations of antioxidants giving higher efficiency in the m-LLDPE polymer containing higher extent of SCB. The presence of the lactone HP136 in mixtures containing hindered phenol-phosphite antioxidant systems gave a higher melt stabilisation efficiency than in its absence and this has been attributed to a co-operative antioxidant reaction steps that take place between the antioxidants resulting in the possible regeneration of the lactone antioxidant through a redox reaction. In all the metallocene PE polymers examined, the biologically hindered phenol, Irganox E, was shown to be more effective than the conventionally hindered phenol Irganox 1076, when examined alone or in combination with phosphite esters.