Synthesis of new 1‐decene‐based LLDPE resins and comparison with the corresponding 1‐octene‐ and 1‐hexene‐based LLDPE resins

This article extends the composition of linear low‐density polyethylene (LLDPE) resins to that containing 1‐decene comonomer units, and examines the effects of comonomer (type and concentration) to copolymerization and physical properties of LLDPE resins. CGC metallocene technology, under high temperature and high pressure (industrial reaction condition), was used to prepare three types of well‐defined LLDPE copolymers containing 1‐hexene, 1‐octene, and 1‐decene units. They show high molecular weight with narrow molecular weight and composition distributions, comparative catalyst activities, and similar comonomer effects. However, 1‐decene seems to exhibit significantly higher comonomer incorporation than 1‐hexene and 1‐octene, which may be associated with its high boiling point, maintaining liquid phase during the polymerization. The resulting LLDPE copolymers show a clear structure–property relationship. Melting temperature and crystallinity of the copolymer are governed by mole % of comonomer. The increase of branch density linearly decreases the LLDPE melting point and exponential reduction of its crystallinity. On the other hand, the density of the copolymer decreases with the increase of comonomer weight %, which shows a sharp linear relationship in the low comonomer content. The tensile properties of 1‐decene‐based LLDPE are very comparative with those of the commercial LLDPE resins with similar compositions. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 639–649, 2007     

Spatially inhomogeneous crystallinity in heterogeneous ethylene‐α‐olefin copolymers

The crystallinity development in heterogeneous ethylene‐1‐butene copolymers is compared with that in ethylene copolymers, with more bulky 1‐heptene as a comonomer. The thermal transitions of the 1‐heptene based copolymers persistently occur at higher temperatures than of the corresponding 1‐butene copolymers. The earlier crystallization onset is reflected in thicker primary crystals, which in turn are associated with the presence of longer ethylene sequences because of the inaccessibility of 1‐heptene to sterically shielded catalytic sites. In addition, the 1‐heptene based copolymers are characterized by a higher degree of primary crystallinity, whereas the 1‐butene copolymers exhibit more prominent secondary crystallization. The 1‐butene based copolymers thus have a less heterogeneous chemical composition distribution. At high comonomer contents, the highly heterogeneous nature of the 1‐heptene copolymers is emphasized by a more pronounced presence of low crystalline spherulite inclusions accomplished by the liquid–liquid phase separation of dissimilar polymeric chains before crystallization. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3000–3018, 2005     

Permeation measurements in ethylene‐1‐hexene,ethylene‐1‐octene,and ethylene‐1‐dodecene copolymers synthesized with metallocene catalysts

The permeation behavior of different ethylene‐1‐hexene, ethylene‐1‐octene, and ethylene‐1‐dodecene copolymers synthesized with metallocene catalysts has been analyzed. These copolymers cover a wide range of comonomer contents, so their crystallinities display rather considerable variations. The results for the permeability to oxygen of the different ethylene copolymers show that the main factor influencing the permeability is the noncrystalline fraction, although some influence of the kind of comonomer may also be present, which may be explained by the fact that when the alkyl branch of the α‐olefin is longer, there is an increase in the free volume in the amorphous and interfacial regions, causing slightly higher values of the permeability coefficient. From the results with different gases, it follows that, in general, an increase in the size of the penetrant (as expressed by its kinetic diameter or critical molar volume) leads to an increase in the solubility and a decrease in the diffusion coefficient. A wide range of permeability values is covered by these ethylene copolymers, depending basically on the crystallinity of the sample, but the permselectivity of CO₂ with respect to oxygen (and probably between other pairs of gases) does not differ very much among the different copolymers. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2174–2184, 2003     

Metallocenic copolymers of ethylene and 5,7‐dimethylocta‐1,6‐diene: Structural characterization and mechanical behavior

The relationship between the structure and mechanical properties has been established for several copolymers of ethylene and 5,7‐dimethylocta‐1,6‐diene synthesized with a metallocene catalyst. A dependence on the composition and polymerization temperature has been found. The branches cannot be incorporated into the orthorhombic crystal lattice, and consequently, structural parameters such as the crystallinity and crystal size are considerably affected as the 5,7‐dimethylocta‐1,6‐diene content increases in the copolymers. The viscoelastic relaxations have been analyzed and compared with those exhibited by high‐density polyethylene (HDPE). The β relaxation does not appear in HDPE and is exclusively seen in the copolymers. As the 5,7‐dimethylocta‐1,6‐diene content rises, the intensity of this process is increased, and its location is shifted to a lower temperature up to comonomer contents of approximately 6–8 mol % in the copolymers. On the other hand, the α mechanism associated with motion within the crystalline regions is also moved to a lower temperature and its intensity is diminished as the 5,7‐dimethylocta‐1,6‐diene molar fraction increases in the copolymers. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3797–3808, 2004     

The copolymerization of propylene with higher,linear α‐olefins

Propylene was copolymerized with the linear α‐olefins 1‐octene, 1‐decene, 1‐tetradecene, and 1‐octadecene. The metallocene catalyst Me₂Si(2‐Me Benz[e]Ind)₂ZrCl₂, in conjunction with methylalumoxane as a cocatalyst, was used to synthesize the copolymers. The copolymers were characterized by ¹³C and ¹H NMR with a solvent mixture of 1,2,4‐trichlorobenzene (TCB) and benzene‐d₆ (9/1) at 100 °C. Thermal analyses were carried out to determine the melting and crystallization temperatures, whereas the molecular weights and molecular weight distributions were determined by gel permeation chromatography with TCB at 140 °C. Glass‐transition temperatures were determined with dynamic mechanical analysis. Relationships among the comonomer type and amount of incorporation and the melting/crystallization temperatures, glass‐transition temperature, crystallinity, and molecular weight were established. Moreover, up to 3.5% of the comonomer was incorporated, and there was a decrease in the molecular weight with increased comonomer content. Also, the melting and crystallization temperatures decreased as the comonomer content increased, but this relationship was independent of the comonomer type. In contrast, the values for the glass‐transition temperature also decreased with increased comonomer content, but the extent of the decrease was dependent on the comonomer type. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 4110–4118, 2000     

High molar mass ethene/1‐olefin copolymers synthesized with acenaphthyl substituted metallocene catalysts

The influence of ligand structure on copolymerization properties of metallocene catalysts was elucidated with three C₁‐symmetric methylalumoxane (MAO) activated zirconocene dichlorides, ethylene(1‐(7, 9)‐diphenylcyclopenta‐[a]‐acenaphthadienyl‐2‐phenyl‐2‐cyclopentadienyl)ZrCl₂ ( 1 ), ethylene(1‐(7, 9)‐diphenylcyclopenta‐[a]‐acenaphthadienyl‐2‐phenyl‐2‐fluorenyl)ZrCl₂ ( 2 ), and ethylene(1‐(9)‐fluorenyl‐(R)1‐phenyl‐2‐(1‐indenyl)ZrCl2 ( 3 ). Polyethenes produced with 1 /MAO had considerable, ca. 10% amount of trans‐vinylene end groups, resulting from the chain end isomerization prior to the chain termination. When ethene was copolymerized with 1‐hexene or 1‐hexadecene using 1 /MAO, molar mass of the copolymers varied from high to moderate (531–116 kg/mol) depending on the comonomer feed. At 50% comonomer feed, ethene/1‐olefin copolymers with high hexene or hexadecene content (around 10%) were achievable. In the series of catalysts, polyethenes with highest molar mass, up to 985 kg/mol, were obtained with sterically most crowded 2 /MAO, but the catalyst was only moderately active to copolymerize higher olefins. Catalyst 3 /MAO produced polyethenes with extremely small amounts of trans‐vinylene end groups and relatively low molar mass 1‐hexene copolymers (from 157 to 38 kg/mol) with similar comonomer content as 1 . These results indicate that the catalyst structure, which favors chain end isomerization, is also capable to produce high molar mass 1‐olefin copolymers with high comonomer content. In addition, an exceptionally strong synergetic effect of the comonomer on the polymerization activity was observed with catalyst 3 /MAO. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 373–382, 2008     

The “comonomer effect” in ethylene/α‐olefin copolymerization using homogeneous and silica‐supported Cp2ZrCl2/MAO catalyst systems: Some insights from the kinetics of polymerization,active center studies,and polymerization temperature

Homogeneous and silica‐supported Cp₂ZrCl₂/methylaluminoxane (MAO) catalyst systems have been used for the copolymerization of ethylene with 1‐butene, 1‐hexene, 4‐methylpentene‐1 (4‐MP‐1), and 1‐octene in order to compare the “comonomer effect” obtained with a homogeneous metallocene‐based catalyst system with that obtained using a heterogenized form of the same metallocene‐based catalyst system. The results obtained indicated that at 70 °C there was general rate depression with the homogeneous catalyst system whereas rate enhancement occurred in all copolymerizations carried out with the silica‐supported catalyst system. Rate enhancement was observed for both the homogeneous and the silica‐supported catalyst systems when ethylene/4‐MP‐1 copolymerization was carried out at 50 °C. Active center studies during ethylene/4‐MP‐1 copolymerization indicated that the rate depression during copolymerization using the homogeneous catalyst system at 70 °C was due to a reduction in the active center concentration. However, the increase in polymerization rate when the silica‐supported catalyst system was used at the same temperature resulted from an increase in the propagation rate coefficient. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 267–277, 2008     

Copolymerization of propylene with various higher α‐olefins using silica‐supported rac‐Me2Si(Ind)2ZrCl2

The copolymerization of propylene with 1‐hexene, 1‐octene, 1‐decene, and 1‐dodecene was carried out with silica‐supported rac‐Me₂Si(Ind)₂ZrCl₂ as a catalyst. The copolymerization activities of the homogeneous and supported catalysts and the microstructures of the resulting copolymers were compared. The activity of the supported catalyst was only one‐half to one‐eighth of that of the homogeneous catalyst, depending on the comonomer type. The supported catalyst copolymerized more comonomer into the polymer chain than the homogeneous catalyst at the same monomer feed ratio. Data of reactivity ratios showed that the depression in the activity of propylene instead of an enhancement in the activity of olefinic comonomer was responsible for this phenomenon. We also found that copolymerization with α‐olefins and supporting the metallocene on a carrier improved the stereoregularity and regioregularity of the copolymers. The melting temperature of all the copolymers decreased linearly with growing comonomer content, regardless of the comonomer type and catalyst system. Low mobility of the propagation chain in the supported catalyst was suggested as the reason for the different polymerization behaviors of the supported catalyst with the homogeneous system. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3294–3303, 2001     

Structure characterization of copolymers of ethylene and 1‐octadecene

Four ethylene‐1‐octadecene copolymers and the corresponding polyethylene homopolymer, synthesized with a metallocene catalyst, have been analyzed by using three characterization techniques in the solid state: differential scanning calorimetry, wide‐angle X‐ray diffraction, and Raman spectroscopy. Very important annealing effects are observed in the copolymers with higher comonomer content while standing at room temperature, in such a way that the enthalpies of melting derived from the first and second melting are different. The X‐ray diffractograms have been analyzed in terms of amorphous and crystalline components, determining both the crystallinity and the position of the different reflections. The variation of the unit cell parameters has been calculated from those reflections. No indication of a possible participation of the relatively long 1‐octadecene branches in the crystallization can be deduced from the X‐ray data. The degree of crystallinity has also been determined from the Raman spectra, following two procedures. The results indicate that the crystallinities deduced from the band at 1416 cm⁻¹ are much lower than those derived from the other two characterization techniques. On the contrary, the data from the 1060 cm⁻¹ band are practically coincident with the X‐ray determinations. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1440–1448, 2000     

Differential scanning calorimetry,small‐angle X‐ray scattering,and wide‐angle X‐ray scattering on homogeneous and heterogeneous ethylene‐α‐copolymers

The objective of this work was to use both X‐ray and differential scanning calorimetry techniques in a comparative study of the lamellar and crystalline structures of heterogeneous and homogeneous ethylene‐α‐copolymers. The samples differed in the comonomer type (1‐butene, 1‐hexene, 1‐octene, and hexadecene), comonomer content, and catalyst used in the polymerizations. Step crystallizations were performed with differential scanning calorimetry, and the crystallinity and lamellar thicknesses of the different crystal populations were determined. Wide‐angle X‐ray scattering was used to determine crystallinities, average sizes of the crystallites, and dimensions of the orthorhombic unit cell. The average thickness, separation of the lamellae, and volume fractions of the crystalline phase were determined by small‐angle X‐ray scattering (SAXS). The results revealed that at densities below 900 kg/m³, polymers were organized as poorly organized crystal bundles. The lamellar distances were smaller and the lamellar thickness distributions were narrower for the homogeneous ethylene copolymers than for the heterogeneous ones. Step‐crystallization experiments by SAXS demonstrated that the long period increased after annealing. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1860–1875, 2001     

Chain microstructure of homogeneous ethylene‐1‐alkene copolymers and characteristics of single site catalysts using a direct 13C NMR peak method I. Theory and models

To describe the detailed microstructure of homogeneous ethylene‐1‐alkene copolymer chains and to study the characteristics of single site catalysts, Markov statistics are used to fit peak intensities of all relevant ¹³C NMR signals of series of copolymers. In the case of the occurrence of inverted comonomer units, a first‐order Markov terpolymer is applied, otherwise a second‐order Markov copolymer model. Chain propagation probabilities are obtained via modeling of the entire NMR spectrum. This procedure results in an accurate reproduction of the chain microstructure, including ethylene, 1‐alkene, and methylene sequence length distributions. If the experimental (co)monomer feeds are known, the reactivity ratios and the theoretical (co)monomer feeds are also found providing information about the copolymerization kinetics and the characteristics of the catalyst. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 722–737, 2006     

Synthesis of new amphiphilic diblock copolymers containing poly(ethylene oxide) and poly(α‐olefin)

This article discusses an effective route to prepare amphiphilic diblock copolymers containing a poly(ethylene oxide) block and a polyolefin block that includes semicrystalline thermoplastics, such as polyethylene and syndiotactic polystyrene (s‐PS), and elastomers, such as poly(ethylene‐co‐1‐octene) and poly(ethylene‐co‐styrene) random copolymers. The broad choice of polyolefin blocks provides the amphiphilic copolymers with a wide range of thermal properties from high melting temperature ～270 °C to low glass‐transition temperature ～?60 °C. The chemistry involves two reaction steps, including the preparation of a borane group‐terminated polyolefin by the combination of a metallocene catalyst and a borane chain‐transfer agent as well as the interconversion of a borane terminal group to an anionic (? O^?K⁺) terminal group for the subsequent ring‐opening polymerization of ethylene oxide. The overall reaction process resembles a transformation from the metallocene polymerization of α‐olefins to the ring‐opening polymerization of ethylene oxide. The well‐defined reaction mechanisms in both steps provide the diblock copolymer with controlled molecular structure in terms of composition, molecular weight, moderate molecular weight distribution (M_w/M_n < 2.5), and absence of homopolymer. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3416–3425, 2002     

Copolymerization of ethylene with 1‐hexene promoted by novel multi‐chelated non‐metallocene complexes with imine bridged imidazole ligand

A series of novel bridged multi‐chelated non‐metallocene catalysts is synthesized by the treatment of N,N‐imidazole, N,N‐dimethylimidazole, and N,N‐benzimidazole with n‐BuLi, 2,6‐dimethylaniline, and MCl₄ (M = Ti, Zr) in THF. These catalysts are used for copolymerization of ethylene with 1‐hexene after activated by methylaluminoxane (MAO). The effects of polymerization temperature, Al/M molar ratio, and pressure of monomer on ethylene copolymerization behaviors are investigated in detail. These results reveal that these catalysts are favorable for copolymerization of ethylene with 1‐hexene featured high catalytic activity and high comonomer incorporation. The copolymer is characterized by ¹³C NMR, WAXD, GPC, and DSC. The results confirm that the obtained copolymer features broad molecular weight distribution (MWD) about 33–35 and high 1‐hexene incorporation up to 9.2 mol %, melting temperature of the copolymer depends on the content of 1‐hexene incorporation within the copolymer chain and 1‐hexene unit in the copolymer chain isolates by ethylene units. The homopolymer of ethylene has broader MWD with 42–46. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 417–424, 2010     

Copolymerization of ethylene with cyclopentene or 2‐butene with half titanocenes‐based catalysts

Half titanocenes (CpCH₂CH₂O)TiCl₂ (1), (CpCH₂CH₂OCH₃)TiCl₃ (2), and CpTiCl₃ (3), activated by methylaluminoxane (MAO) were tested in copolymerization of ethylene with internal olefins such as cyclopentene. All the catalysts were able to give incorporation of cyclopentene in polyethylene matrix. ¹³C NMR analysis of obtained copolymers showed that the catalytic systems have low regiospecificity. In fact, in ethylene–cyclopentene copolymers, cyclic olefin inserts with both 1,2 and 1,3‐enchainment. X‐ray powder diffraction analysis of these copolymers confirmed that 1,2 inserted cyclopentene units are excluded from crystalline phase, whereas 1,3‐cyclopentene units are included, giving rise to expansion of unit cell of crystalline polyethylene. Titanium‐based catalysts were investigated also in the copolymerization of ethylene with E and Z‐2‐butene. Only complex (1) was able to give copolymers and ¹³C NMR analysis of products showed 2‐3, 1‐3, and 1‐2 insertion of 2‐butene. Differential scanning calorimetry analysis displayed that ethylene–cyclopentene, as well as ethylene‐2‐butene, copolymers are crystalline and their melting point decreases by increasing the comonomer content. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4725–4733, 2008     

Copolymerization of propylene with higher α‐olefins in the presence of the syndiospecific catalyst i‐Pr(Cp)(9‐Flu)ZrCl2/MAO

The catalyst system i‐Pr(Cp)(9‐Flu)ZrCl₂/methylaluminoxane was used for the synthesis of random syndiotactic copolymers of propylene with 1‐hexene, 1‐dodecene, and 1‐octadecene as comonomers. An investigation of the microstructure by ¹³C NMR spectroscopy revealed that the stereoregularity of the copolymers decreased because of an increase in skipped insertions in the presence of the higher 1‐olefin. The melting temperature of the copolymers, as measured by differential scanning calorimetry (DSC), decreased linearly with increasing comonomer content independently of the comonomer nature. During the DSC heating cycle, an exothermic peak indicating a crystallization process was observed. The decrease in the crystallization temperature with higher 1‐olefin content, measured by crystallization analysis fractionation, indicated a small but significant dependence on the nature of the comonomer. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 40: 128–140, 2002     

Ethylene/1‐heptene copolymers as interesting alternatives to 1‐octene‐based LLDPE: Molecular structure and physical properties

Classical linear low density polyethylenes (LLDPEs) are copolymers of ethylene and 1‐octene or 1‐hexene, respectively. In the past, other 1‐olefins have been tested as comonomers but the resulting LLDPEs were never commercialized as large scale products. The present study focuses on the use of 1‐heptene as an interesting comonomer for the synthesis of LLDPE. For a comparison of the molecular structure and the physical properties of 1‐heptene‐ and 1‐octene‐based LLDPEs, five Ziegler–Natta LLDPEs of varying comonomer contents based on 1‐heptene and 1‐octene, respectively, were acquired and analysed using advanced methods. The comonomer contents of the resins were between 0.35 and 6.4 mol %. Crystallization‐based techniques revealed similar bimodal distributions that are due to the formation of copolymer and polyethylene homopolymer fractions. The compositional distribution of the copolymers was studied by high‐temperature (HT) HPLC and HT‐2D‐LC. The analytical results indicate similar chemical heterogeneities and molar mass distributions of the two sets of LLDPE up to a comonomer content of 3 mol %. Similar to the molecular structure, the physical properties of the materials are quite similar. At comonomer contents of ≥3 mol % differences between the two sets of samples are seen that are attributed to differences in the abilities of 1‐heptene and 1‐octene in disrupting the crystal arrangements of the polymer chains in solid state. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 962–975     

Multi‐center nature of heterogeneous Ziegler–Natta catalysts: TREF confirmation

A new approach to detailed Tref analysis of ethylene/α‐olefin copolymers prepared with multi‐center polymerization catalysts is developed. It is based on resolution of complex Tref curves into elemental components described with the Lorentz distribution function. This approach was applied to the study of a series of ethylene/1‐butene copolymers prepared with a supported Ti‐based catalyst. The analysis showed that the copolymers, which, on average, contain from 6.5 to 3.5 mol % of 1‐butene, consist of seven discrete components with different compositions, ranging from a completely amorphous material with a 1‐butene content of > 15–20 mol %, to two highly crystalline components with 1‐butene contents < 1 mol %. A comparison of these Tref results with the data on the molecular weight distribution of the copolymers (based on resolution of their GPC curves) shows that Tref and GPC data provide complimentary information on the properties of active centers in the catalysts in terms of the molecular weights of the material they produce and their ability to copolymerize α‐olefins with ethylene. Tref analysis of copolymers produced at different reaction times showed that the active centers responsible for the formation of various Tref components differ in the rates of their formation and in stability. The centers that produce copolymer molecules with a high 1‐butene content are formed rapidly but decay rapidly as well whereas the centers producing copolymer molecules with a low 1‐butene content are formed more slowly but are more stable. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 4351–4362, 2005     

Effects of Alterations to Ziegler–Natta Catalysts on Kinetics and Comonomer (1‐Butene) Incorporation

Various MgCl₂‐supported Ziegler–Natta (ZN) catalysts are synthesized with the intention to influence polymerization performance and 1‐butene incorporation in an ethylene copolymer. Modifications are introduced during different steps in the synthesis process, namely support preparation, titanation, and catalyst workup. While multiple different effects are observed upon modification, heat treatment during titanation shows the greatest impact. Increasing the heat‐treatment temperature increases polymerization activity. More importantly, the 1‐butene distribution can be shifted toward a more homogeneous profile. The amount of 1‐butene incorporated is similar to both for short‐ and for very long‐chain molecules. This behavior has so far been known only from metallocene‐based polyethylene and suggests that active sites are distributed more homogeneously in the ZN catalyst.

     

Ethylene/1‐octene copolymerization studies with in situ supported metallocene catalysts: Effect of polymerization parameters on the catalyst activity and polymer microstructure

Ethylene and 1‐octene copolymerizations were carried out with an in situ supported rac‐[dimethylsilylbis(methylbenzoindenyl)] zirconium dichloride catalyst. In a previous study, it was found that some in situ supported metallocenes produced polyethylene/α‐olefin copolymers with broad and bimodal short chain branching distributions and narrow molecular weight distributions. The ability to produce polyolefins with multimodal microstructural distributions in a single metallocene and a single reactor is attractive for producing polymers with balanced properties with simpler reactor technology. In this study, a factorial experimental design was carried out to examine the effects of the polymerization temperature and ethylene pressure, the presence of hydrogen and an alkylaluminum activator, and the level of the comonomer in the feed on the catalyst activity, short chain branching distribution, and molecular weight distribution of the polymer. The temperature had the most remarkable effect on the polymer microstructure. At high 1‐octene levels, the short chain branching distribution of the copolymer broadened significantly with decreasing temperature. Several factor interactions, including the hydrogen and alkylaluminum concentrations, were also observed, demonstrating the sensitivity of the catalyst to the polymerization conditions. For this catalyst system, the responses to the polymerization conditions are not easily predicted from typical polymerization mechanisms, and several two‐factor interactions seem to play an important role. Given the multiple‐site nature of the catalyst, it has been shown that predicting the polymerization activity and the resulting microstructure of the polymer is a challenging task. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 4426–4451, 2002     

Correlation of the elution behavior in temperature rising elution fractionation and melting in the solid‐state and in the presence of a diluent of polyethylene copolymers

Compositionally homogeneous poly(ethylene‐α‐olefin) random copolymers with 1‐butene and 1‐hexene comonomers have been studied. The melting of solution‐crystallized specimens of these copolymers in the presence of trichlorobenzene as a diluent with differential scanning calorimetry (DSC) is well correlated with analytical temperature rising elution fractionation (A‐TREF) elution temperature profiles. This indicates that the A‐TREF experiment is essentially a diluent melting experiment. Furthermore, the correction of the corresponding solid‐state melting endotherms of these copolymers with Flory's diluent melting equation yields curves that also correlate very well with the DSC diluent melting curves and the A‐TREF elution temperature profiles. Values of χ, the Flory–Huggins interaction parameter, are determined for these copolymers in trichlorobenzene. χ decreases as short‐chain branching increases. The A‐TREF elution temperature profiles of one of these copolymers are the same, within experimental error, for dilute‐solution crystallizations of the copolymer performed over an extremely broad time schedule (10 s to 3 days). This indicates the profound effect of the branches, as limiting points of the ethylene sequences, in controlling the crystal thickness distribution, which in turn controls the melting point in the presence of the diluent, or the elution temperature from the A‐TREF. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2819–2832, 2001