AZ91镁合金表面稀土转化膜的制备及耐蚀性能研究

采用在镁合金表面形成无毒、无污染的稀土铈转化膜的方法解决AZ91镁合金表面的腐蚀问题。确定了最佳成膜工艺参数，讨论了处理液的浓度、成膜温度和成膜时间等因素对转化膜耐蚀性的影响。利用湿热实验、阳极极化曲线的测定等实验方法评价了转化膜对镁合金表面的防护作用。结果表明，在潮湿温热条件下稀土铈转化膜试样仍能保持膜层的完整性并具有较高的覆盖度，腐蚀现象不明显。腐蚀电势升高，出现钝化现象，腐蚀电流密度下降，稀土铈转化膜可以提高AZ91镁合金的耐蚀性能。用扫描电镜观察了膜的微观形貌，稀土铈转化膜是由基膜和附着的细小颗粒组成，最佳工艺形成的铈转化膜无破碎现象，对AZ91镁合金表面的腐蚀过程的发生有明显的抑制作用。     

电化学阻抗谱研究铈盐转化膜形成过程中的影响因素

应用电化学阻抗谱(EIS)连续测试B95铝合金在0.01 mol·L-1CeCl3溶液中铈盐转化膜的形成过程,通过成膜过程中交流阻抗值的变化研究了温度,溶解氧O2的变化对B95铝合金稀土转化膜成膜过程的影响机制,采用等效电路的方式对测试的EIS进行了解析.结果表明:温度在20,25,30 ℃时B95铝合金在0.01 mol·L-1CeCl3溶液中的阻抗谱等效电路与成膜形成阶段的相同;温度为35,40,45℃B95铝合金的阻抗谱与成膜成长阶段的等效电路相同,表明升高温度缩短了稀土膜形成阶段的时间,铝合金基体溶解迅速被抑制;升高温度有利于铈盐氧化膜的形成;通O2对稀土Ce转化膜的形成无明显促进作用,O2参与的反应不是Ce转化膜形成的决速步骤.     

铝合金稀土转化膜成膜工艺研究

应用正交实验设计 ,开发并研究了LY1 2铝合金 4价铈盐转化膜的成膜工艺及其膜层的耐蚀性能 .实验表明 :经稀土转化处理的铝合金其点蚀电位升高 ,自然腐蚀电位有所降低 ,从而降低了点蚀敏感性 ;试样极化阻力提高 70倍以上 ,耐蚀性能大大提高 ,与铬酸盐相当 ;另外 ,还结合电化学测试和表面分析 ,初步探讨了铝合金稀土转化膜的耐蚀机理     

掺铈纳米TiO2薄膜制备及光催化降解甲醛甲苯

通过Sol-Gel工艺在玻璃表面及多孔陶瓷表面制得了均匀透明的掺铈纳米TiO2薄膜．通过SEM、XRD及UV-Vis等手段对玻璃表面掺铈纳米TiO2薄膜进行了表征．结果表明，薄膜表面无开裂现象、膜内部比表面积大、TiO2分布均匀．薄膜中出现的锐钛矿相在(101)面有一定的择优取向，且UV-Vis研究表明，掺铈纳米TiO2薄膜在近紫外的吸光度有明显提高．利用自行设计的反应器，以多孔陶瓷为介质，对甲醛、甲苯等有机物进行了光催化降解研究．结果表明，掺铈纳米TiO2薄膜对甲醛甲苯有极高的光催化降解效率，由于薄膜成本低廉，易于工业化，为净化室内空气开辟了新的途径．     

铝合金阳极氧化膜上交流电沉积制备含铈复合膜

通过交流电解沉积的方法在铝合金阳极氧化膜上制备了稀土铈复合膜, 并考察了氧化膜的厚度对形成复合膜的影响. 电解成膜溶液为含1 g · L-1 CeCl3 · 7H2O和10 mL · L-1 H2O2的水溶液, 正弦交流电的平均电压为10 V, 交流沉积的时间为5 min. 结果表明, 阳极氧化膜的厚度是影响成膜的主要因素, 在实验中, 氧化膜的厚度大于6.8 μm时才能形成连续均匀的复合膜. 测试分析结果表明, 复合膜表面的铈元素分布均匀, 平均含量为1.70%(质量分数);Ce元素主要分布在氧化膜多孔层的表层, 分布深度约1.5 μm.     

石墨纤维增强铝基复合材料表面稀土转化膜微观结构

石墨纤维表面和铝基体表面均有稀土膜层存在，EDS面扫描结果认定Ce含量达47．48％，Ce，O，Al，Si是组成膜的主要元素。Ce转化膜在成膜初期微裂纹不明显，但这一阶段成膜较薄，10min时膜层开始出现明显微裂纹。稀土膜层衍射斑点中存在连续的衍射环，也有大量的衍射斑点里不连续的环状排布，说明稀土膜层的晶体结构为纳米微晶，同时存在部分非晶体。由于Ce化合物十分复杂尚未能标定出它的具体晶体结构。Gr（f）／Al复合材料表面稀土膜层是由纳米微晶和非晶体的混合物颗粒堆积而成的，颗粒堆积留下的微孔在成膜初期不明显，但随成膜时间延长，堆积产生的微孔效应越来越明显，由此产生了稀土膜的微裂纹；加之成膜过程的不均匀性，膜层内应力增加以及膜层水分散失等原因也会导致微裂纹的形成。     

环氧树脂涂覆LY12铝合金在NaCl溶液中的阻抗模型

分别研究了裸LY12铝合金及涂覆环氧树脂涂层后合金在3.5％NaCl溶液中的电化学阻抗谱（EIS）.结果表明,LY12铝合金在点蚀电位以下阻抗谱上出现两个容抗弧,高频段对应Cl－参与的成膜阻抗,低频段对应铝阳极溶解的电化学反应阻抗.合金发生点蚀后出现低频感抗弧.合金/电极在NaCl溶液中先发生涂层吸水,当水及O2抵达基体后建立起电化学反应界面,合金遭受腐蚀；受涂层阻挡的影响,腐蚀产物的扩散逐渐成为控制步骤；当扩散速度较慢的Cl－抵达涂层/金属界面后,与界面处聚集的腐蚀产物间发生化学反应,完成成膜过程,阻抗谱上出现盐膜的阻抗,而扩散阻抗消失.提出了不同浸泡失效阶段涂层电极体系的阻抗模型.     

碳钢表面稀土转化膜的XPS和AES研究

用浸渍法在Ａ３钢表面上获得了稀土转化膜，此膜呈均匀的金黄色，有良好的装饰效果。硫酸铜点滴、盐水浸泡、硫化氢气体等加速腐蚀试验以及膜层的电化学测试均证实此膜具有一定的耐蚀性能。膜层的ＸＰＳ９Ｘ射线光电子光谱）分析结果表明，膜层由铁、铈、氧等元素组成；在膜层的表面，铁以Ｆｅ＾３＋，铈以Ｃｅ＾４＋状态存在，在膜层的内部，铁以Ｆｅ＾３＋及Ｆｅ＾３＋，铈以Ｃｅ＾３＋和Ｃｅ＾４＋状态存在；从ＡＥＳ（俄歇Ｆｅ＾     

L-蛋氨酸对预腐蚀Q235碳钢缓蚀性能的分子动力学研究

采用失重法、密度泛函理论和分子动力学模拟研究了预腐蚀对L-蛋氨酸在60℃、1M的HCl溶液中对Q235碳钢的影响和缓蚀剂的缓蚀机理。结果表明:预腐蚀作用降低了L-蛋氨酸对Q235碳钢缓蚀作用,缓蚀率下降15%。密度泛函理论和分子动力学模拟结果表明,羧基上的氧原子带有明显的负电荷能够吸附到金属表面形成缓蚀剂膜,发挥缓蚀作用,为成膜缓蚀机理。L-蛋氨酸在没有预腐蚀的Q235碳钢表面吸附分子数为24时,缓蚀剂膜最致密。而L-蛋氨酸在预腐蚀后的Q235碳钢表面吸附时的吸附能显著降低,缓蚀剂在碳钢表面的分布密度也明显下降,这很好解释了预腐蚀作用降低了缓蚀剂缓蚀率的实验结果。本文的研究结果对缓蚀剂的研究和实际应用具有一定的指导意义。     

镁合金铈转化膜的形成及表征

采用X射线光电子能谱（XPS）、原子力显微镜（AFM）、电化学方法等对AZ31镁合金铈转化膜的组成、形貌结构及耐蚀性能进行了表征,并结合成膜动力学研究探讨了膜的形成机制。结果表明,镁合金铈转化膜的主要成分为铈的氧化物/氢氧化物,铈在膜中以三价和四价两种价态存在。膜可以分为两层,内、外层膜由不同的微结构组成,这种微结构的差异使内、外层膜之间结合力较弱,成为限制膜耐蚀性能提高的根本原因之一。成膜过程中,成膜溶液pH值升高,使Ce3＋发生水解反应沉积析出铈的氢氧化物/氧化物。铈转化膜的生长动力学遵循抛物线规律。     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

恶臭嗅辨实验室建设探讨

针对恶臭测试的环境影响问题,提出了解决的实例方案,并对方案的要点及优缺点进行讨论,此方案在实际操作中具有较好的效果。     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.     

Mechanism of action of base-catalyzed oxygenation of phenol derivatives

Cyclopropyl derivative of 2,6-di-tert-butylphenol is synthesized as a probe to investigate the mechanism of base-catalyzed autooxidation of phenol derivatives. Our study indicates that one electron reduction of molecular oxygen from phenolate gives phenoxyl radical 3, a key intermediate of autooxidation. The coupling of phenoxyl radical and superoxide radical gives peroxylate anion 4 and produces the final epoxy alcohol adduct 6.     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

解决能源问题的新途径——光解水制氢的研究

面对日益枯竭的能源危机,氢能是一种洁净、最有前景的替代能源。目前在各种制氢的方法中光催化分解水制氢的研究最多,光解水过程中催化剂最关键,本文对利用太阳能光解水的途径、提高光催化反应效率以及光催化剂的开发研究进行了综述。