硅橡胶热降解动力学的研究

用恒温热失重方法，研究了甲基硅橡胶（Ｓｉ—Ｏ—１），用氢氧化钾催化聚合的甲基硅橡胶（Ｓｉ—Ｏ—２），主链含环二硅氮烷的硅氮橡胶（Ｓｉ—Ｎ—１）以及它与Ｓｉ—Ｏ—１的共混物Ｓｉ—Ｏ—３和与Ｓｉ—Ｏ—２的共混物Ｓｉ—Ｏ—４的热降解反应动力学．结果表明Ｓｉ—Ｎ—１有最高的热稳定性，在氮气下，其降解反应活化能为３４４ｋＪ／ｍｏｌ．并且发现它分别与Ｓｉ—Ｏ—１和Ｓｉ—Ｏ—２的共混物的热稳定性大幅度提高．Ｓｉ—Ｏ—３在氮气下的降解活化能由未加入Ｓｉ—Ｎ—１前的１５２ｋＪ／ｍｏｌ提高到２３０ｋＪ／ｍｏｌ；Ｓｉ─Ｏ─４则由未混入Ｓｉ─Ｎ─１前的６１ｋＪ／ｍｏｌ提高到１４４ｋＪ／ｍｏｌ．我们认为这种作用机理是由于硅氮橡胶除去了微量吸附水和硅羟基并导致催化剂的离子对难于分离的结果．     

茂金属间规立构聚丙烯结晶动力学研究

用ＤＳＣ和密度法对茂金属间规立构聚丙烯（ｓＰＰ）样品进行了等温和非等温结晶动力学研究．测得平衡熔点Ｔ０ｍ为１５８℃,平衡熔融热焓ΔＨ０ｍ为３７ｋＪ／ｍｏｌ,侧表面自由能σ＝５２ｅｒｇ／ｃｍ２,折叠链表面自由能σｅ＝６９ｅｒｇ／ｃｍ２,链堆砌功ｑ＝３３７５ｋＪ／ｍｏｌ．对非等温结晶过程研究表明,由熔体结晶的ｓＰＰ具有非均相成核,三维球状生长机理．成核与生长活化能ΔＥ＝７３１ＫＪ／ｍｏｌ     

脱水KFI沸石中钾离子分布的模拟退火研究

基于四个固定的参量设值：阳离子位能差ＥＭ２－ＥＭ１＝２５．５０ｋＪ／ｍｏｌ、ＥＭ３－ＥＭ１＝－１０．７３ｋＪ／ｍｏｌ和最近邻阳离子对互作用能Ｗ１２＝４５．６ｋＪ／ｍｏｌ、Ｗ１４＝０．５６ｋＪ／ｍｏｌ以及一个温度依赖的参量ＥＭ４－ＥＭ１＝２．６８（Ｔ／３２３）２．５ｋＪ／ｍｏｌ，以能量极小原则，通过模拟退火优化途径研究了ＫＫＦＩ（Ｋ２２．４Ａｌ２２．４Ｓｉ７３．６Ｏ１９２）沸石分子筛中钾离子在四个结晶学不等价可交换阳离子位（Ｍ１－４）上分布的温度依赖。理论预测的阳离子位占据率Ｐｉ（ｉ＝１～４）在Ｔ＝３２３～９２３Ｋ温域与高温ＸＲＤ实验分析数据相符。     

丙烯酰胺微乳液聚合

由乳化剂聚乙二醇壬基苯基醚ＯＰ、聚乙二醇壬基苯基醚（ＴＸ—４）、丙烯酸胺、水和煤油组成微乳液时，体系中水相丙烯酸胶浓度及体系温度对乳化剂最小量有明显的影响；而ＯＰ、ＴＸ—４比例及油水比例的影响不大．本文研究了辐射引发微乳液聚合的动力学，得到如下表达式：聚合速率及聚合物特性粘数的表观活化能分别为５３．２ＫＪ／ｍｏｌ，－３３．２ＫＪ／ｍｏｌ．聚丙烯酸胺微乳液具有特殊的增稠性能，与聚电解质增稠剂相比，电解质对增稠效果的影响不大，而其他表面活性剂的影响较大．     

阳离子交换树脂催化氯乙酸和甲醇酯化反应动力学

以强酸性阳离子交换树脂为催化剂合成氯乙酸甲酯，研究催化反应的动力学，研究确定为表观正、逆向二级反应，求得其表观活化能为Ｅａ＋＝３４．２０１ＫＪ／ｍｏｌ，Ｅａ＝４８．３０５ＫＪ／ｍｏｌ。     

交换稀土La^3^＋离子NaY型分子筛的交流电导

本文用Ｘ－射线衍射，原子吸收光谱，差热热重，化学分析等方法测定了交换Ｌａ＾３＾＋离子ＮａＹ分子筛的物相及组成，用交流阻抗谱仪测量了其离子电导。由电导率随温度的变化，得到ＮａＹ和ＬａＮａＹ的电导表观活化能为４９．６ＫＪ／ｍｏｌ和４１．３ＫＪ／ｍｏｌ。讨论了交换Ｌａ＾３＾＋离子对分子筛骨架结构中的钠离子分布，落位及其扩散迁移的影响。     

在N—甲基吡咯烷酮中聚苯硫醚合成的宏观动力学

研究了无水硫化钠与对二氯苯（以Ｎ－甲基吡咯烷酮为溶剂）合成聚苯硫醚反应的宏观动力学，该反应是一个小分子缩合串联自缩聚的过程，通过测定不同反应聚合体系中氯化钠的徨成率和硫化内的转化率，建立了该反应的宏观动力学方程：１／（１－ＰＮａＣｌ＋ＰＮａ２ｓ）＝Ｃ０Ｋｔ＋１；并计算得到２２０、２５０℃的表观反应速率为４．５×１０＾－４和３．０×１０＾－３ｋｇ／（ｍｏｌ．ｓ），表观活化能为１３４ｋＪ／ｍｏｌ。     

TiO2超细粉热稳定性的研究

本实验以ＴｉＣｌ４为原料，采用超临界流体干燥法地出ＴｉＯ气凝胶超细粉，在６２３－９２３Ｋ温度范围内考察了其织构和结构的热稳定性。实验发现，随着焙烧温度的提高，样吕的比表面和孔体积减小表面堆积密度增大，同时伴随颗粒烧结长大并连成链状。对ＴｉＯ２气胶超细粉的烧结机理研究表明，其烧结为表面扩散控制过程，烧结活化能为２２２．６ｋＪ／ｍｏｌ。     

卡宾与醚C——H键插入反应的理论研究（Ⅱ）：——二氯卡宾？…

用量子化学从头算方法在ＭＰ２／６－３１Ｇ（ｄ）水平上研究了单重态的ＣＸ２（Ｘ＝Ｆ,Ｃｌ）与二甲醚中Ｃ－－Ｈ键的插入反应。两个体系的插入反应都是自发的,插入过程是ＣＸ２的亲电－新核过程。ＣＸ２与二甲醇的插入势垒分别为１２５．９ＫＪ／ｍｏｌ（经零点能校正后为１３２．２ＫＪ／ｍｏｌ,Ｘ＝Ｃｌ）和２５５．３ＫＪ／ｍｏｌ（经零点能校正后为２５７．６ＫＪ／ｍｏｌ,Ｘ＝Ｆ）。ＣＦ２的插入反应实际上难以发生。     

用ab initio方法研究NaN_3的几何构型、电子结构和热力学、动力学性质

用ａｂｉｎｉｔｉｏＭＯ方法，在ＭＰ２（ｆｕｌ）／６３１１Ｇ水平下，全优化计算了叠氮化钠（ＮａＮ３）分子的线状和环状两种稳定构型及其转化过渡态的几何参数、电荷分布、分子总能量和振动频率，并研究了它们的热力学性质及转化速率常数和平衡常数．结果表明，线状比环状构型稍稳定（能量低６．０４ｋＪ／ｍｏｌ）；两者相互转化的能垒分别为１３．１５ｋＪ／ｍｏｌ（线型→环状）和７．１１ｋＪ／ｍｏｌ（环状→线型）．热力学和动力学计算均表明：ＮａＮ３通常主要以线型结构存在（占８５％以上），且随温度升高而增多（在１０００Ｋ大于９１％）．     

多苯基三联苯有机硅化合物的合成及其对聚合物耐热性影响的研究

本文通过Diels-Alder反应合成了1,4-双(2′,3′,6′-三苯基,4′-四甲基乙烯基二硅氧基苯基)苯(简称Ⅰ)和1,4-双(2′,3′,6′-三苯基,4′-三乙氧基硅基苯基)苯(Si称Ⅱ)两种新的多苯基三联苯有机硅单体,产率均为80％左右,并作了下列耐热性研究,其结果:(1)把化合物(Ⅰ)作为硅橡胶的热稳定剂,所得硅弹性体在300℃×150小时老化后,具有较好的耐热性和机械性能;(2)化合物(Ⅱ)可以做室温胶的交联剂,所得胶片在300℃×48小时老化,仍保持好的弹性。     

Quantification of radiation induced crosslinking in a commercial, toughened silicone rubber, TR55 by H MQ-NMR

Radiation induced degradation in a commercial, filled silicone composite has been studied by SPME/GC-MS, DMA, DSC, swelling, and multiple quantum NMR. Analysis of volatile and semi-volatile species indicates degradation via decomposition of the peroxide curing catalyst and radiation induced backbiting reactions. DMA, swelling, and spin-echo NMR analysis indicate an increase in crosslink density of near 100% upon exposure to a cumulative dose of 250 kGray. Analysis of the sol fraction via Charlesby-Pinner analysis indicates a ratio of chain scission to crosslinking yields of 0.38, consistent with the dominance of the crosslinking observed by DMA, swelling and spin-echo NMR and the chain scissioning reactions observed by MS analysis. Multiple quantum NMR has revealed a bimodal distribution of residual dipolar couplings near 1 krad/s and 5 krad/s in an approximately 90:10 ratio, consistent with bulk network chains and chains associated with the filler surface. Upon exposure to radiation, the mean 〈Ω_d〉 for both domains and the width of both domains increased. The MQ-NMR analysis provided increased insight into the effects of ionizing radiation on the network structure of silicone polymers.     

交联剂对无皂P(MMA-EA-MAA)种子聚合乳胶粒成孔的影响

采用完全无皂种子乳液聚合技术合成了粒径窄分布的P(MMA-EA-MAA)乳胶粒,通过对上述胶乳进行碱处理,制备出了具有空腔结构和多孔结构的聚合物乳胶粒,研究了交联剂的种类和用量对聚合过程、胶粒特性及胶粒结构形态的影响.结果表明,体系中加入交联剂后,单体转化率都有不同程度的提高;随交联剂用量的增加,乳胶粒粒径略有减小,交联剂用量较高时,乳胶粒粒径分布加宽;二乙烯基苯(DVB)的交联效率稍高于双甲基丙烯酸乙二醇酯(EGDMA);不加入交联剂及EGDMA用量低于0.5%时,处理后乳胶粒呈空腔结构,加入DVB及EGDMA用量高于1.0%时,处理后乳胶粒呈多孔结构,并且乳胶粒体积增量随交联剂用量的增加而减小.     

Thermal behaviour and mechanical properties of novel RTV silicone rubbers using divinyl-hexa[(trimethoxysilyl)ethyl]-POSS as cross-linker

Divinyl-hexa[(trimethoxysilyl)ethyl]-POSS (DVPS) as an octavinyl-POSS derivative was first prepared. A series of novel polydimethylsiloxane (PDMS)/DVPS hybrid materials as room temperature vulcanized (RTV) silicone rubber were prepared. The chemical incorporation of novel POSS into hydroxyl-terminated PDMS system by hydrolytic condensation reaction was verified by attenuated total reflection (ATR) infrared spectroscopy. Thermal degradation, thermo-oxidative stability and mechanical properties of these novel RTV silicone rubbers were studied by means of thermogravimetric analysis and tensile testing. The results exhibited significantly enhanced effects on the thermal stabilities and mechanical properties as compared to the PDMS polymer prepared with tetraethoxysilane (TEOS). The observed improvements in thermal properties could be attributed to the effective three-dimensional network structures resulting from the structure of DVPS. The thermal decomposition of the RTV silicone rubbers in nitrogen was also monitored by TGA coupled with real-time FTIR, and the degradation residues were also characterized by FTIR. It was found that the POSS cross-linker facilitated the formation of cross-links in the degradation residues. The striking improvement in mechanical properties could be attributed to the synergistic action of the structure of three-dimensional multi-arm cross-linker (vinyl-POSS derivative), the plasticization of self-cross-linking Vinyl-POSS derivative and perfect distribution of vinyl-POSS derivative.     

高热稳定性硅橡胶的研究

阐述了在硅橡胶主链中引入硅氮结构,在硅橡胶中添加硅氮化合物或采用硅氮交联剂对改进硅橡胶热稳定性的影响,提出了利用Ｓｉ－Ｎ键的反应去消除引起硅橡胶主链降解的硅羟基和水平达到提高其热稳定性的作用机理。采用阴离子活性聚合的方法合成了具有低玻璃化温度的耐高温的聚硅氧烷弹性体。     

Synergistic effect between POSS and fumed silica on thermal stabilities and mechanical properties of room temperature vulcanized (RTV) silicone rubbers

In this paper, both divinyl-hexa[(trimethoxysilyl)ethyl]-POSS (DVPS) and fumed silica were firstly introduced into polydimethylsiloxane (PDMS) system using as the cross-linker and the reinforcing filler respectively. And a series of novel RTV silicone rubbers synergistically enhanced by DVPS and fumed silica were prepared. The cross-linked networks in the novel RTV silicone rubbers have been studied by attenuated total reflection infrared spectroscopy, and the dispersions of POSS and fumed silica in these novel RTV silicone rubbers have been observed by means of scanning electron microscope (SEM). And thermal stabilities, thermo-oxidative stabilities and mechanical properties of these novel RTV silicone rubbers were studied by means of thermal gravimetric analysis and universal tensile testing machine, respectively. From the obtained results, it was found that synergistic effect between POSS-rich areas and fumed silica on thermal stability and mechanical property of RTV silicone rubber indeed existed. And the experimental results also exhibited that the thermal stabilities and mechanical properties of the novel RTV silicone rubbers were far better than those of the reference materials (DVPR and MTFR). The striking enhancements in thermal properties and improvements on mechanical properties of novel RTV silicone rubbers were likely attributed to the synergistic effect between POSS-rich domains and fumed silica. Meanwhile, it was found that the mechanical properties of RTV silicone rubbers prepared with a given amount of POSS cross-linker were enhanced with the increment of the loading amount of fumed silica.     

碳酸钙与碳化硅对室温硫化硅橡胶的补强作用

在有关硅橡胶补强的研究中,人们已经对ＳｉＯ２ 等补强性填料对硅橡胶的补强作用进行了深入的研究,但对非补强填料对室温硫化硅橡胶的补强作用则相对涉及较少．作者研究了ＣａＣＯ３ 和ＳｉＣ 两类非补强性填料以及填料的粒径与分布对室温硫化硅橡胶拉伸强度、断裂伸长率和耐温性能等的影响,发现合适粒径的非补强性填料对室温硫化硅橡胶有较好的补强效果,且在填料粒径及分布匹配时有最好的补强效果,选用ＳｉＣ时还可以有效提高室温硫化硅橡胶的热稳定性．     

交联剂用量对PMVS/CB复合材料压阻特性的影响

本文研究交联剂用量对PMVS/CB导电复合材料单轴压阻特性的影响, 并讨论PMVS交联密度与复合体系单轴压阻性能之间的关系.     

Viscoelastic and thermal characterization of crosslinked PVC

Soft PVC is employed for the manufacturing of a wide range of products with different properties and a relatively low cost. The utilization of soft PVC is restricted by the poor thermal, chemical and mechanical resistance properties. Also, plasticizer migration can modify the properties or can make useless the materials for some applications because of toxicity or a general loss of properties. PVC crosslinking is the most effective way to improve mechanical and transport properties of rigid or flexible PVC at high temperatures, but at the same time the thermal stability of PVC may be significantly reduced. In this work, the crosslinking reaction of plasticized poly(vinyl chloride) (PVC) through difunctional amines was studied. The mechanisms involved in the crosslinking reaction were explained by Fourier transform infrared (FTIR) analysis. The thermal activated crosslinking reaction was studied by cone and plate rheometry, analyzing the evolution of viscoelastic properties of the suspension as a function of time and temperature. The effect of the addition of crosslinking agents on the thermal stability of the polymer was studied by thermogravimetric analysis (TGA), which revealed that crosslinking reactions promote thermal degradation phenomena in the polymer matrix. This is attributed to the formation of HCl and other species promoting polymer degradation during crosslinking, thus leading to higher weight loss during thermal treatment with respect to unmodified PVC plastisols. This was also confirmed by an evident yellowing after crosslinking, especially at higher temperatures.     

丙烯酸酯类吸油树脂的合成与性能研究

以丙烯酸酯、甲基丙烯酸酯为主要单体,二丙烯酸丁二醇酯为交联剂,过氧化二苯甲酰为引发剂,采用悬浮聚合方法,合成聚丙烯酸酯类高吸油树脂.研究了分散剂、引发剂、交联剂用量及单体配比等因素对树脂吸油性能的影响.结果表明,分散剂用量为单体质量的0.12%,引发剂用量为1.0%,交联剂用量为1.5%时树脂的吸油能力最佳,吸甲苯倍率可达15倍,吸汽油倍率可达10倍,吸机油倍率可达近9倍.