二氧化钛纳米棒在空心微球表面的定向生长

通过表面预处理和水热法开展了用二氧化钛包覆空心微球的研究, 用扫描电子显微镜(SEM)和X射线衍射仪(XRD)等表征了所得产品, 并探索了各种反应参数对产物形貌和结构的调控作用. 实验结果表明, 空心微球的表面溶胶-凝胶预处理至关重要. 采用表面溶胶-凝胶技术预处理空心微球表面, 然后在一定条件下进行水热反应, 我们在空心微球表面上成功地包覆了垂直于微球表面并紧密排列的锐钛矿型二氧化钛纳米棒. 该材料质轻、耐腐蚀, 有望成为一种新型光催化剂, 应用于治理水体表面的大面积污染.     

锌离子掺杂的二氧化钛介孔空心微球的制备及光催化性能

以二氧化硅为模板,钛酸四丁酯(TBOT)为钛源,硝酸锌为锌源,采用溶胶凝胶法制备了锌离子掺杂的介孔二氧化钛空心微球。采用X射线衍射(XRD)、比表面积(BET)、透射电镜(TEM)、扫描电镜(SEM)和X射线光电子能谱(XPS)等技术对样品进行表征,以亚甲基蓝(MB)的光催化降解为目标反应评价其光催化活性。结果表明,去核之后的复合微球为空心微球,壁厚为20 nm左右。钛酸四丁酯溶液的滴加时间对微球的形貌影响较大,当滴加时间大于15 min时,可以得到结构清晰的空心微球。用氢氧化钠溶液去除二氧化硅核,反应90 min,二氧化硅可以被完全去除。X射线衍射表明,实验得到的掺杂锌离子的空心微球和没有掺杂锌离子的空心微球都是锐钛矿。当锌离子的摩尔分数为0.3%时,二氧化钛空心微球的晶粒尺寸最小,比表面积最大,催化亚甲基蓝降解的效率最高。     

锌离子掺杂的二氧化钛介孔空心微球的制备及光催化性能

以二氧化硅为模板,钛酸四丁酯（TBOT）为钛源,硝酸锌为锌源,采用溶胶凝胶法制备了锌离子掺杂的介孔二氧化钛空心微球。采用X射线衍射（XRD）、比表面积（BET）、透射电镜（TEM）、扫描电镜（SEM）和X射线光电子能谱（XPS）等技术对样品进行表征,以亚甲基蓝（MB）的光催化降解为目标反应评价其光催化活性。结果表明,去核之后的复合微球为空心微球,壁厚为20nm左右。钛酸四丁酯溶液的滴加时间对微球的形貌影响较大,当滴加时间大于15min时,可以得到结构清晰的空心微球。用氢氧化钠溶液去除二氧化硅核,反应90min,二氧化硅可以被完全去除。X射线衍射表明,实验得到的掺杂锌离子的空心微球和没有掺杂锌离子的空心微球都是锐钛矿。当锌离子的摩尔分数为0.3%时,二氧化钛空心微球的晶粒尺寸最小,比表面积最大,催化亚甲基蓝降解的效率最高。     

空心锌铬铁氧体/二氧化钛复合物的制备及去污性能

以葡萄糖溶液为原料,通过水热法制备了分散性良好的碳微球;以碳微球为模板,应用化学沉淀法和热处理技术除去碳核获得空心铬锌铁氧体;用钛酸四丁酯作为钛源,在空心铁氧体表面包覆二氧化钛制备了锌铬铁氧体/二氧化钛二元复合物.采用现代分析技术表征了制备样品的微观结构、形貌和电磁性能,并对其吸附和降解染料废水的性能进行了研究.结果表明,Zn Cr_(0.25)Fe_(1.75)O_4对染料废水具有较好的去污效果,对甲基橙和罗丹明B的去污效率分别为87%和83%;TiO_2对铁氧体的包覆能提高复合物对染料废水的光催化降解性能,其中m_(T/ZCF)=0.3的ZnCr_(0.25)Fe_(1.75)O_4/TiO_2复合物的去污效果最佳,几乎与纯二氧化钛相仿.     

纳米棒和纳米片构建的CuO空心微球可控合成及其形貌依赖的声催化活性

在180℃下,CuCl_2和NH_3·H_2O水热反应制备了纳米片构建的CuO空心微球。在上述体系中,加入乙二醇,制备了纳米棒构建的CuO空心微球。其形成机理是以NH_3气泡为模板的原位吸附生长过程。以酸性大红为例,比较了两者的声催化性能,结果表明,纳米棒构建的CuO空心微球声催化性能强于纳米片构建的CuO空心微球。     

单分散α-Fe_2O_3纳米结构空心亚微球的制备及表征

采用一种新的溶液生长法结合多步包覆法在自制的不同粒径SiO2单分散亚微球表面包覆不同厚度的β-FeOOH涂层,得到单分散β-FeOOH/SiO2核壳结构亚微球.实验结果表明,SiO2核心颗粒尺寸对表面涂层的形态和包覆均匀性有很大影响.当SiO2核心颗粒的平均粒径为250 nm左右时,β-FeOOH表面涂层均匀,颗粒间团聚较少,一次包覆后涂层厚度约为35 nm.涂层中β-FeOOH纳米棒的尺寸随着所选SiO2核心颗粒粒径的增大而相应增大.经多次包覆能够显著提高涂层的厚度,3次包覆后β-FeOOH表面涂层厚约100 nm.β-FeOOH/SiO2核壳结构亚微球与质量分数5%的NaOH溶液反应后,于600℃焙烧2 h得到了单分散α-Fe2O3空心微球.单分散α-Fe2O3空心亚微球表层是由α-Fe2O3纳米棒搭建而成的三维网络结构,α-Fe2O3纳米棒的尺寸与核壳结构中β-FeOOH纳米棒的尺寸基本一致.     

金纳米棒@碳中空胶囊的制备及催化性能

以聚吡咯为碳壳前驱体制备了金纳米棒镶嵌于碳壳内的中空胶囊.先合成羧基修饰的聚苯乙烯微球和十六烷基三甲基溴化铵稳定的金纳米棒; 再利用二者之间的静电力将金纳米棒组装在聚苯乙烯微球表面; 最后, 通过氧化聚合将聚吡咯壳包覆在聚苯乙烯@金纳米棒复合物的表面.在氮气保护下经高温煅烧, 聚吡咯壳被碳化为碳壳的同时聚苯乙烯微球分解, 从而制得金纳米棒@碳中空胶囊.在煅烧过程中, 由于碳壳的保护, 金纳米棒很好地保持了“棒状”形貌.通过调节吡咯单体的浓度, 可以控制聚吡咯壳和碳壳的厚度.金纳米棒@碳中空胶囊在以NaBH₄为还原剂还原亚甲基蓝的反应中表现出良好的催化活性.     

膨胀石墨层间生长高活性氧化锌及其光催化性能

以醋酸锌和膨胀石墨为原料, 采用真空辅助压力诱导手段使反应溶液注入膨胀石墨层间, 在180℃下溶剂热反应12 h, 一步得到氧化锌纳米棒/石墨烯复合光催化剂, 采用X射线衍射仪(XRD)和透射电子显微镜(TEM)等对复合光催化剂的结构和形貌进行了表征. 结果表明, 合成的氧化锌纳米棒具有六方晶系纤锌矿结构; 氧化锌纳米棒在石墨烯表面分散性较好, 其平均直径约50 nm, 长度约150~200 nm. 所得氧化锌纳米棒/石墨烯复合材料对亚甲基蓝的降解效率优于目前应用最广泛的光催化剂Degussa P25.     

共沉淀法制备Ag/AgCl-TiO2空心复合纳米微球及其光催化性能

通过甲基丙烯酸与苯乙烯聚合制备了表面负电性的聚苯乙烯(PSt)纳米乳胶粒. 在乙醇与水的混合溶剂中, 用硅烷偶联剂乙烯基三甲氧基硅烷对其进行表面改性后加入钛酸四丁酯、 氯化钠和硝酸银, 以PSt乳胶粒为模板采用共沉淀法制备了PSt-AgCl-TiO₂复合微球. 在180 ℃对其进行液相预处理及煅烧去除PSt模板后制备了Ag/AgCl-TiO₂空心复合粒子. 对各阶段产物的形貌、 晶体结构和比表面积等进行了表征. 结果表明, 所得产物为Ag/AgCl与锐钛矿型TiO₂复合的空心粒子, 其比表面远大于商品TiO₂(P25). 考察了Ag/AgCl-TiO₂复合粒子在紫外光与可见光下对罗丹明B(RhB)降解的催化活性. 结果表明, 在紫外光下n(Ag)/n(Ti)=0.1%的Ag/AgCl-TiO₂复合粒子活性最高, 30 min时对RhB的降解率比不含Ag/AgCl的TiO₂空心微球提高了13%; 虽然Ag/AgCl-TiO₂在可见光下的催化活性远比紫外光下低, 但与纯TiO₂空心纳米微球相比其催化活性仍明显增强. n(Ag)/n(Ti)=2.0%的Ag/AgCl-TiO₂复合粒子催化活性最高, 120 min时对RhB的降解率比不含Ag/AgCl的TiO₂空心微球提高了38%.     

环境化学实验“自制海藻酸钙包覆纳米铁降解亚甲基蓝速率常数的测定”

纳米铁系材料用于去除水体中的污染物是当前环境修复领域的研究热点之一。将自制的海藻酸钙包覆纳米铁材料用于降解亚甲基蓝的实验引入环境化学实验教学中具有极其重要的意义。实验过程包括制备海藻酸钙包覆纳米铁材料,绘制了亚甲基蓝的标准曲线,比较不同材料降解亚甲基蓝的效果,比较不同温度下海藻酸钙包覆纳米铁降解亚甲基蓝的效率,研究温度对其降解速率常数的影响。     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

恶臭嗅辨实验室建设探讨

针对恶臭测试的环境影响问题,提出了解决的实例方案,并对方案的要点及优缺点进行讨论,此方案在实际操作中具有较好的效果。     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.